pakedgedevice&software inc. User Manual
Contents
1. 2 The switch and the relevant components are away from electrical noise sources such as radios transmitters and broadband amplifiers 3 The switch is away from environments beyond recommend moisture levels Desktop Installation 1 Install the switch on a level surface that can support the weight of the unit and the relevant components 2 Plug the switch with the female end of the provided power cord and plug the male end to the power outlet Rack mount Installation The switch is supplied with rack mounting brackets and screws for rack mounting the unit Procedures to Rack Mounting the Switch tn the rack 1 Disconnect all the cables from the switch before continuing 2 Place the unit on a hard flat surface with the front facing you 3 Locate the mounting bracket over the mounting holes on one side of the unit 4 Insert the screws and fully tighten with a screwdriver 5 Repeat the two previous steps for the other side of the unit 6 Insert the unit into the rack and secure with suitable screws 7 Reconnect all the cables I nstallation of Network Cables l Crossover or straight through cable Al the ports on the switch support Auto MDI MDI X functionality Both Straight through or crossover cables can be used to connect the switch 2 Category 3 4 5 or 5e UTP STP cable To make a valid connection and obtain the optimal performance use appropriate cables corresponding to different transmitting re2. without having an electrical outlet close by Over current protection and circuit shorting protection are also supported to ensure safe operations The SW8 4PB is plug n play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel provide the operating status of individual port and whole system Key Features e Complies with TOBASE T specifications of the IEEE802 3 standard e Complies with LOOBASE TX specifications of the IEEE802 3u standard e Compliant with IEEE 802 3af PoE standard DTE power via MDI X e Provides 4 PoE ports with classification identify Supports 15 4W maximum per PoE port Supports over current protection and circuit shorting protection e 9 RJ 45 ports for 100BASE TX and LOBASE T connectivity e Supports NWay protocol for speed 10 100Mbps and duplex mode Half Full auto detection Supports MDI MDI X auto crossover Wire speed packet filtering and forwarding rate e Store and forward architecture filters fragment amp CRC error packets e Supports 1K MAC entries 768K Bits buffer memory Supports extensive LED indicators for network diagnostics e Internal universal switching power supply FCC Class A CE VCCI Class A The Front Panel The front panel consists of LED indicators Please refer to the following paragraph for detailed LED definition LEDs Definition The switch contain 1 pow
3. ceiving speed Please refer to the following table for information Media Speed Wiring 10 Mbps Category3 4 5 10 100 Mbps UTP STP ports 100 Mbps Category 5 UTP STP Ports that 10 100 Mbps Category5 5e support PoE UTP STP or Port 1 Port4 above S PoE 1 4Port 2 x 2 J PoE IP Camera Hh aS AP Router Rou Wireless PoE Router AP Desktop PC NoteBook Product Specifications i EEE802 3 LOBASE T i EEE802 3u 100BASE TX Standard EEE802 3af Power over Ethernet o LLLL1IEEE802 3x flow control 8 10 100 Mbps auto MDI MDI X RJ 45 ports Port1 4 support PoE power feeding Interface Network Data 10 100 Mbps Rate Auto negotiation Transmission 10 100Mbps Full duplex Mode Haltaupex LED System Power indications Ports 10 100M PoE gt gt gt gt gt E gt gt gt 1K MAC entries 768K Bits buffer Memory FCC Class A ot CE VCCI ClassA o 64 32W max with 4 x 15 4 Power W PoE Device connected Consumption 4 848W max with no PoE Device connected Operating 0 40 C 32 104 F Temperature 77 7 Operating i ano Humidity 10 90 non condensing 48V 1 35A Power Supply 100 240V 47 63 H
4. er LED for the device 1 10 100M LED for each port and 1 PoE LED for port 1 port 4 System LED Status Operation powered on powered off Port LEDs LED Status Operation Green The port is connected 10 LOOM Green receiving No valid link on this port One PoE compliant Green device is connecting with this port There is no PoE compliant device connecting with this port Off The Rear Panel The rear panel consists of one power receptacle and 8 RJ 45 ports Port 1 to Port 4 also support connecting to PoE devices Pet ww Power Receptacle To be compatible with the electric service standards around the world the switch accepts a power supply in the range of 100 to 240VAC 50 60Hz Please make sure that your outlet is within this range To power on the switch please plug the female end of the power cord firmly into the receptacle of the switch and the other end into an electric service outlet After the power cord installation please check if the power LED is lit for normal power status Installation This switch can be placed on your desktop directly or mounted in a rack The installation is a snap Users can use all the features of the switch by simply attaching the cables and turning the power on Before installing the switch we strongly recommend 1 The switch is placed in a well ventilated environment a minimum 25mm space around the unit is recommended
5. pakedgedevice amp software inc SW8 4PB 8 Port Fast Ethernet with 4 Port PoE Switch User Manual Version 2 1 FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Merk lei This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible
6. that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2007 All Rights Reserved Unpacking I nformation Thank you for purchasing Pakedge Device amp Software SW8 4PB Before installation please check that your package contains the following items 1 One 4 4 10 100 PoE Switch 2 One power cord 3 User s Manual Introduction General Description SW8 4PB is a powerful high performance Fast Ethernet Switch with all 8 ports capable of 10 or 100Mbps auto negotiation operation NWay The SW8 4PB could automatically negotiate with the connected partners on network speed and duplex mode It Is ideal for micro segmenting large networks into smaller connected subnets for improved performance thus enabling the bandwidth demanding multimedia and imaging applications Moreover the 10 100Mbps auto sensing ability provides an easy way to migrate 10Mbps to 100Mbps network with easy The SW8 4PB supports PoE which supplies power for connected devices via CAT 5 and above twisted cables By integrating the data transmitting cable and power cord it make setting up your network easier You could easily connect a Wireless AP or a VoIP phone to this switch
7. z universal Input Technical Support Please visit our website for up to date support information Website www pakedge com Email support pakedge com CONTACT INFORMATION Pakedge Device amp Software Inc 1011 Edwards Road Burlingame CA 94010 Pakedge Device amp Software Inc 2007 All Rights Reserved
Download Pdf Manuals
Related Search