USER MANUAL
Contents
1. LP 101 USER MANUAL wireless electronics Thank you for purchasing Wintec products Based on the innovative technology in this ever changing environment we have been developed many wireless products that have attract more consumers attentions We sincerely appreciate your interest for our products and we suggest you read the instruction carefully Your comment will be highly valued Please read through the manual in order to get familiar with the device and learn the features of this model Certificate Approval fe O fs Z Safety Warning The following safety precautions shall always be observed during operation Do not modify the radio for any reason Use only Wintec supplied or approved batteries and chargers To avoid electromagnetic interference and or compatibility conflicts turn off your radio in any area where posted notices instruct you to do so Turn off your radio before boarding an aircraft Any use of a radio must be in accordance with airline regulations or crew instructions Turn off your radio prior to entering any area with explosive and flammable materials Do not use any portable radio that has a damaged antenna If a damaged antenna comes into contact with your skin a minor burn can result Do not expose the radio to direct sunlight over a long time nor place it close to heating source When transmitting with a portable radio hold the radio in a vertical position with the microphone 3 to 4 centimet2. Press and hold the power button around 1sec to power on the radio Press and hold the power button around 1sec to turn radio off Note When turned off successfully the monitor will shut down and you ll hear the turn off sound Receiving Transmitting Before press and hold the PTT button please check if the LED indicator turns on green or not Green stands for channel busy Press PTT button and speak clearly with your mouth about 5cm away from the microphone The LED indicator turns on red during transmission Release PTT button when you finish speaking and receive signals During receiving LED indicator turns on green Adjusting Volume Press repeatedly on Up button to adjust the volume louder Press repeatedly on Down button to decrease the volume Press and hold UP or Down button can quick adjust the volume louder or lower There is a total of 16 levels display and each adjustment increase or decrease by 2 levels Adjust the volume slowly to avoid outburst of sound harmful to ears Channel Adjustment Press CH button While channel icon blinks the radio is in the channel selection mode Press A V to select the assigned channel Press CH button or PTT again to set the channel and exit the channel selection CTCSS Tone Adjustment Press twice CH button the icon will flash and enter the CTCSS adjustment mode The Screen indicate OF when the code turns off above the icon Press A V
3. to enable and select the assigned tone on channel When the code is set press PTT CH or SET button to jump off and return to the main page There are 51 standard codes of CTCSS as below table Factory default is OFF ctcss e e25 16 1140 26 1622 96 2335 26 1890 e s85 18 1230 28 173 8 ea 2503 28 1095 e ors 19 1273 20 1799 eo 603 49 2065 C EXA Keypad Lock Unlock Hold on SET button for about 1 sec till KA shows on the screen to confirm keypad lock is enabled Hold on SET button again the G disappear on the screen to disable the keypad lock function Note When keypad is locked all buttons are locked expect PTT unlock volume adjustment and power button LCD Backlight On Off Press any button to initiate the backlight and press PTT button to turn off the backlight The backlight will automatically turn off after 7 sec 6 Power Adjustment Hold PTT button and simultaneously press A to expand to high power Yul or press V to switch to low power Y Tone Call Selection Hold PTT and press SET button once together to sent out the tone call to other units Scan Channel Press CH button when channel icon blinks hold A or V around 2 secs to perform the channel scanning When performing the auto scanning jumping of channel numbers increasingly or decreasingly indicates scan in progress Scan stops when it detects a busy cha
4. ar on the screen when the VOX function is enabled Headset The icon is lit up when the headset is connected Volume There are a total of eight levels display and 16 levels of volume adjustment control Channel Number Indicates the current channel 44 CTCSS 51 groups in CTCSS Code Activated indication Please refer to the table listed as below Battery Level 4 level indication Shows the remaining charge of the battery capacity Keypad Lock Indicates that all operations on the keypad are disabled besides PTT unlock volume adjustment and power button D Programming Mode The icon is lit up when the radio is under programming mode t Battery Installation w Press and hold the battery latch locked on the bottom and remove the case upward as in Fig 1 Place or take out AA or LI ION battery pack into battery compartment as in illus 1 Please note that to install the lithium battery into its compartment it needs to be put flat with front side upward Place the battery case from top to the button and press the case until a click sound is heard fix as in Fig 2 It will lock into compartment Operation Guide Before operating the radio make sure the attached battery is fully charged When the battery level is very low you need to recharge it before you can continue to use your radio The radio has a battery voltage icon to show the battery status on LCD screen Power On Off
5. ers away from your lips Keep antenna at least 2 5 centimeters away from your body when transmitting Packaged Model Contents When you receive your radio package inspect the shipping carton for any signs of damage Next remove and check the contents of the packing case to be sure that all items ordered have been included Contents of the packing case may be different from those listed if optional accessories were ordered 1 Radio Unit 2 Battery 3 Belt Clip 4 Rapid Charger and Transformer 5 User s manual Contents Radio Overview s soe e ee ee ee Tain Es PRE AAA ee Installation of Accessories 4 Operation Guide roer Fiinction Men s lt x s lt k eee we es 8 Optional Accessories lt lt lt lt IO Radio Overview Antenna PTT Button Push to talk Up Key Down Key Speaker Area E External Microphone Jack LED Indicator ES LCD Screen E Power Button Channel Code Adjustment Function Key Keypad Lock Microphone LCD Icons Yull d Yulll ise C mie ath T ic con ang fx Signal Strength Shows the signal strength Five bars indicate the strongest signal The more bars of signals on the screen the stronger the signal received Scanning On When the scan function enabled the icon amp will appear on the screen and flash once the signal is receiving Vox On The icon will appe
6. ll be flashing on the main screen Optional Accessories LP 10M Swivel Belt Clip for best placement and take out the radio LP CHG 10B Desktop Rapid Charger charging time 2hrs BT FR 10LI E 3 7V 1250mAh Li ion batteryin the transceiver LP 10A LP 10B Earbud Headsets W S Earhook Headsets LP 10C PB 101 Air tube Headsets Leather Case WI AL10 Programmable Cables Note Pictures are for reference only and may vary from actual product Product function shall remain the same The above listed items are the common optional accessories for your radio To order other accessories please contact your local dealer Wintec endeavors to achieve the accuracy and completeness of this manual but no warranty of accuracy or reliability is given All the above specifications and design are subject to change without notice due to continuous development No part of this manual may be copied reproduced translated stored in a retrievable system distributed or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Wintec www wintec com tw PK EZ01 S 2 VER 1
7. nnel Temporarily press any PTT CH or Set button will disable scan and select the final busy cannel The radio will only scan the channels in the list Note To perform the scan function please turn off the CTCSS code in advance Function Menu Press and hold P2 button to enter the function menu Press A V to select the function settings OFF VOX OFF Levell Level 9 Tone Call ES Keypad Tone mw ON OFF OFF 1 1 1 2 Power Save O 1 3 1 4 SQL Adjustment Adjust radio s squelch level between Level 0 Level 7 The smaller grade to be set the weaker signals can be detected by the speaker but the radio is susceptible to interferences Level O means the SQL is turned off VOX Adjustment VOX s sensitivity adjustment can be selected in OFF 1 9 levels 1 stands for the highest sensitivity 9 stands for the lowest That means the smaller of the no means the better ability to transmit the signals Tone Call Selection There are totally 11 kinds of tone call for selection The range is from b0 b10 Keypad Tone Press A V to enable ON or disable OFF this function Power Saving Mode Press A V to enable ON or disable OFF this function Enable power saving mode could extend radio operation time There are 4 levels for options Choose 1 4 if talk time is short for best power saving and in general 1 2 is for the proper use When in the power saving mode the icon Yall wi
Download Pdf Manuals
Related Search