OWNERS MANUAL
Contents
1.2. Auto button until Manual appears near the bottom left hand corner of the screen The Set Temperature will now appear at the top of the screen with the current room temperature still visible in the top right of the screen The Set Temperature is the temperature the air conditioning system is set to maintain To alter it use the Rotary Dial to select the temperature required Fan operation can be toggled between automatic and continuous operation using the Key 1 button Where applicable economy operation can be toggled on and off using the combination of the Function button followed by the Key 4 button Period Description Wake Define the time and settings to operate your system before you get up in the morning system when you have left for the day system just before you get home i system at night Where applicable the mode of operation can be cycled between heat only cool only and heating cooling operation using the Mode button Note that the Networker limits the Set Temperature to a maximum of 30 C and a minimum of 8 C If the minimum is exceeded the air conditioning system is switched off and the Set Temperature indicated as Note that the Networker remembers your last settings and goes back to them the next time you select manual operation Auto Program Operation 6 3ha 2h 177 Se Ta e ii 4 E 6 FIG 7 Hester Cocke gt In Auto Program mode the Networker allows you to preset your air conditio
3. controlling every aspect of the system s performance The manufacturer reserves the right to discontinue or change specifications or designs at any time without notice and without incurring obligations If anything unusual occurs the Networker will display a message stating Air Conditioner Fault RO1 Code for assistance call 1300 652 349 across the top of the screen There are two parts to the message the R01 number designates which appliance has the fault and the Code relates to the type of fault The screen will also display the spanner symbol Note Whenever such a message appears it is a good idea to write it down before doing anything else This code contains information that will enable Brivis to deal quickly and easily with anything that requires their attention With many of them you will be asked to contact Brivis Service on 1300 BRIVIS and pass on the message the model and type of appliance Message repeating Push the Function button followed by the Key 1 button quickly after to repeat a message Resetting If something has interrupted the units operation the word Reset could appear beside the Key 4 button while a coded message is scrolling across the top of the display When this is the case the Key 4 button can be used to re start the unit If the unit does not resume normal operation or the error message re appears contact Brivis Service Locking Unlocking the Networker To prevent any unwanted a
4. the function button which is detailed later The Rotary Dial This dial is used to alter various settings The display will also show scrolling messages across the top of the screen which can display some of the unit s operational states Brivis Climate Systems Pty Ltd ABN 64 096 079 088 AU24752 The manufacturer reserves the right to discontinue or change specifications or designs at any time without notice and without incurring obligations Setting the Time amp Day 23 BG or Gane a FIG 2 To set the Time and or Day the Networker must be turned OFF using the On Off button e Press the Clock button Key 5 button and the screen will display the message Clock setting mode and then the Digital Clock will flash Use the Rotary Dial to select the right time To set the day press the Day button Key 1 button until the correct day of the week appears on the left of the screen e g Mon e Press the Clock button Key 5 button again to save your new settings Appliance Operating Symbols When the Networker is switched on certain operating symbols appear describing the operation of the air conditioner appliance 12 Ber 26 15 Pari lr a b hiarr e When the Networker switches ON the attached air conditioner appliance to HEAT a flame symbol will appear on the screen Lift Bee 26 24 F FIG 4 Faster der b kirai When the Networker switches ON the attached air condit
5. 9 Pikirler i i If your lifestyle doesn t match the pre set Auto Program you can change the settings to your requirements by pressing the Prog button After this is done the words Auto Program are flashed on the display screen to indicate that the Auto Program settings can be altered When changing the settings the Networker combines all the weekdays into one block and both days of the weekend into another block which are listed on the left hand side of the screen To toggle the block that you want to change the settings for press the Day button Key 1 button To select the time period you want to change press the Period button Key 2 button until the required time period is displayed The combination of the Function button followed by the Key 1 button toggles the operation of the Key 1 button between selecting The required block of days to program and Automatic or continuous fan operation Note that when selecting automatic or continuous fan operation ensure that the word Fan is next to the Key 1 button The Time Temp button can be used to toggle the actual setting the Rotary Dial alters namely the time period Set Time or Set Temperature The setting that is flashing is the one that can be altered by the Rotary Dial Bia Ze FF Ei l Tak Pel om Tii F mml Mii Tir hulo Priya FIG 10 eater Loci With the block of days and time period to program selected you can now program the ac
6. OWNERS MANUAL brivis Climate Systems OPERATING YOUR BRIVIS NC 4 NETWORKER WALL CONTROL Networker Components Lit Ber 26 1F Pari kis b b Aor The On Off Button This is the button to turn the Networker ON or OFF The Function Button Fn The function button when used in conjunction with buttons 1 2 4 amp 5 allows the user to perform specialised functions such as message repeating and Networker locking The Mode Button This button allows you to switch between the available operating modes of the attached reverse cycle air conditioner appliance These include operating as a heater only heating operating as a cooler only cooling or operating as both a heater and cooler heating and cooling with auto changeover The Fixed Control Buttons These two buttons have their permanent functions written on them AUTO Switches the Networker between manual operation and Auto Program operation This button is used to set the Networker s Auto Program settings The Variable Control Buttons These buttons numbered 1 5 have a function when there is text beside the actual button on the display screen The Display Screen Provides you with information about the system The Screen shows the current time via a Digital Clock in the top left corner the Day of the Week on the left hand side and the operating mode selected at the bottom Buttons 1 2 4 amp 5 have additional features when used in conjunction with
7. ioner appliance to COOL a snowman symbol will appear on the screen In both cases the fan symbol will also appear on the display and appears rotating when the fan of the attached air conditioner appliance is switched on Note that a flashing flame or snowman symbol indicates that the compressor within the air conditioner appliance is yet to switch ON DOC No REV Note that a flashing fan symbol indicates that the fan within the air conditioner appliance is yet to switch ON General Operating Symbols lzi 20 24 m a oon ani barra al The thermometer on the display registers the current room temperature with the small marker beside it indicating the temperature that the heating cooling system is currently set to maintain The bar adjacent to the Key 1 button is displayed when continuous fan operation has been enabled using the Key 1 button The Econ symbol is displayed when economy operation has been enabled using the combination of the Function button immediately followed by the Key 4 button Note that the actual room temperature appears in the top right of the display screen Note that continuous fan operation results in the fan being switched on all the time to allow continuous circulation of air Note that the economy operation is only available for reverse cycle air conditioning systems Manual Operation 12 Ber 26 1F i kis b harara Turn the Networker ON and press the
8. lterations being made to the operational settings the Networker can be locked via a 4 digit PIN number In the case of dual networkers if one is locked the other is also locked There can be up to 3 PIN numbers stored into the controller which allows the Networker to be locked or unlocked by various users If dual networkers are installed the user PIN numbers can only be set from the Master Networker The Slave Networker can only lock and unlock the system and cannot access the PIN numbers Setting PIN Numbers Piri deka FIG 13 Push the Function button then the Key 2 button immediately after The screen will then display Enter Your PIN number to lock the system Do not enter numbers at this stage please continue to the next step Push the Mode button once The screen will now display User PIN number reset Enter master PIN number Do not enter numbers at this stage please continue to the next step Push the Mode button once again The screen will now display the message User PIN number 1 alteration Enter current PIN f this is the first time for setting the PIN numbers the current PIN will be 1111 If the PIN has been previously altered then enter your current PIN The screen will then display the message Enter the new PIN Enter your new 4 digit PIN number using a combination of Keys 1 5 The screen will now display Repeat the entry of the new PIN e Providing you re ente
9. ner to switch ON or OFF when you wake leave return and just before you sleep Settings that can be defined include e The start time for the period e The set temperature to be maintained e Automatic or continuous fan operation e The Mode of operation where applicable e Economy operation where applicable In Auto Program mode the Networker has a pre set Auto Program for the entire week the settings of which are defined in the table below Beginning Auto Program Operation If the pre set Auto Program settings suit your lifestyle then all you need to do is run the system in Auto Program mode by following these simple steps Use the On Off button to turn the Networker ON e Use the Auto button until Auto Program appears on the display screen Temporarily Overriding the Auto Program Settings If these pre set Auto Program settings do not suit your lifestyle you may want to temporarily override them by simply using the Networker as you would under manual operation namely To alter the Set Temperature use the Rotary Dial to select the temperature required To alter fan operation use the Key 1 button to toggle between automatic and continuous operation To alter the economy setting use the combination of the Function button followed by the Key 4 button to toggle the economy operation on and off where applicable To alter the operating mode use the Mode button to cycle between heat only cool only and hea
10. pts at entering a valid PIN number On the third failed attempt the message Invalid PIN entered will be displayed At this point the Networker will abort the PIN entry screen and resume the state that it was in prior to attempting to enter the PIN You can immediately retry entering the PIN numbers or if you cannot remember the PIN numbers call Brivis Service on 1300 BRIVIS Dual Networker Operation Where Applicable It is possible to have two networkers connected to the system The two networkers will operate together one will be configured as a Master and the other a Slave and the settings for the system will be common on both controllers The benefit of having two controllers is the convenience of making adjustments to the settings as an adjustment made on one of the networkers is immediately reflected on the other Networker When locking one of the networkers the other one will also be locked and the system can be unlocked at either Networker By default the Master Networker senses room temperature as is indicated by the flashing heart symbol Note that only the Master control has the ability to set the clock time this is one way of identifying which controller is the Master Look for the word clock beside the Key 5 button while the system is in the OFF position The manufacturer reserves the right to discontinue or change specifications or designs at any time without notice and without incurring obligations
11. r the new PIN correctly the screen will now display Valid PIN PIN altered Repeat this process to change the other PINs if necessary Remembering that all PINs are set as 1111 by default Pushing the Mode button while you re at the user PIN 1 alteration screen will give access to set user PIN numbers 2 amp 3 If an incorrect number is entered press the Auto button to clear all digits then re enter your user PIN number To exit this area at any time simply press the On Off button Locking the Networker Push the Function button then the Key 2 button immediately after The screen will now display Enter Your PIN number to lock the system Enter your current user PIN number to lock the Networker The screen will now display System locked out 7 If an incorrect number is entered press the Auto button to clear all digits then re enter your PIN number Unlocking the Networker Push the Function button then the Key 2 button immediately after The screen will now display Enter Your PIN number to unlock the system Enter your current user PIN number to unlock the Networker The screen will now display the message System unlocked If an incorrect number is entered press the Auto button to clear all digits then re enter your PIN number Note If an invalid PIN is entered the message Invalid PIN entered Try again will scroll across the screen The user has three attem
12. ting cooling operation where applicable Economy Mode The manufacturer reserves the right to discontinue or change specifications or designs at any time without notice and without incurring obligations The word Temporary will flash at the bottom of the display screen until the current period ends The Advance Period button Key 2 button has now become the Cancel button This button can be used to return the Networker to the settings defined for the current time period Note that the Networker will revert to the settings defined for the next period after the current period ends Advancing Time Period iIo 15 Fan Cael karir FIG 8 Hester ho If the settings defined by the current time period do not suit your lifestyle you may want to use the settings defined by the next time period In this case the Advance Period button Key 2 button can be used to operate the system using the settings defined by the next time period The word Temporary will flash at the bottom of the display screen along with the time period advanced to being displayed until the current time period ends The Advance Period button Key 2 button has now become the Cancel button This button can be used to return the Networker to the settings defined for the current time period Permanently Changing the Auto Program Settings 60 ee Se Lhe iy Ta el fe th Fri Paice wiis Tea Auh FIG
13. tual settings namely To alter the Set Time use the Rotary Dial to select the time required when the Set Time is flashing To alter the Set Temperature use the Rotary Dial to select the temperature required when the Set Temperature is flashing To alter fan operation use the Key 1 button to toggle between automatic and continuous operation when the Fan word is displayed To alter the economy setting use the combination of the Function button immediately followed by the Key 4 button to toggle the economy operation on and off where applicable To alter the operating mode use the Mode button to cycle between heat only cool only and heating cooling operation where applicable Once all settings have been defined save the new settings by pressing the Prog button Note that selecting a Set Temperature of will turn the air conditioner OFF for that time period Operating the Fan Only 12 ep Fal ee Oa FIG 11 X To simply circulate the air in the house the fan can be made to run continuously With the Networker switched OFF press the Fan button Key 1 button After s small delay a small rotating fan symbol will appear and air should begin circulating within the ductwork of your system To switch the fan OFF simply press the Fan button Key 1 button Coded Messages le Fy a al wt pi bil bk md FIG 12 Mester Sooke While the Networker is operating your system it is also monitoring and
Download Pdf Manuals
Related Search