Owners Manual
Contents
1. cCom au ADAMS 4 iDIMMER LED DIMMING SWITCH LED DIMMING SWITCH Owners Manual iDimmer leading edge LED Dimming switch CONTENTS 01 PRODUCT 2 02 SAFETY 2 03 PRECAUTIONS amp 8 3 04 INSTALLATION 3 05 CARE amp 4 06 REPLACEMENT PARTS AND 4 07 TECHNICAL 4 08 WARRANTY 4 409 5 5 01 Product information 01 1 Model IDimmer LED dimming switch 01 2 Description Leading edge controlled LED dimming switch for control of 1 to 30 iGlobe LED MAXX or SMD series downlights 01 3 Variants 01 3 1 iDimmer leading edge 500watt 02 SAFETY WARNINGS 02 1 This product must be installed by an Australian licensed electrician in accordance with current version of Australian New Zealand Wiring Rules AS NZS3000 02 2 Always read the instructions fully before installation amp use keep for future reference 02 3 Before attempting to insert remove dimmer always ensure the circuit is not energised switch to OFF and RCD off then ensure lamps and drivers are not connected2. of obstructions If installed by an A grade Australian licensed electrician to Australian electrical code the iDimmer will be safe to use 03 3 1 Before making fixing hole s check that there are no obstructions hidden beneath the mounting surface such as pipes or cables 03 4 COMPATIBLE ON SAME CIRCUIT Make sure that all loads on the same circuit are of the same load strength same type of light fitting Mixing 10w and 12w Downlight Maxx units on the same circuit is not recommended 03 5 iGlobe LED only This product has been tested to comply with Australian EMC and SAA safety precautions when using with iGlobe LED down lights only This product is not recommended nor guaranteed under these policies for use with any other light fittings or other electrical products DO NOT USE TO SWITCH SPEED FANS OR OTHER ELECTRICAL EQUIPMENT 04 INSTALLATION PROCEDURE 04 1 Ensure the power to the circuit being used is isolated and will stay isolated until the job is complete Lock out amp Tag out 04 2 Select the appropriate mounting position for your switch plate 04 3 Route the supply to the intended position of the hole wall The supply wiring chosen for this installation is to be selected installed and tested in accordance with AS NZS3000 Wiring Rules 04 4 Select the appropriate position for your dimmer in the switch plate Make sure the rear of the pertruding dimmer and associated wiring is not in conflict with any objects or building materi
3. to the circuit 02 4 Always use the dimmer on the correct power supply and do not exceed the maximum usable dimmer wattage of 400 watts 02 5 This dimming unit is optimized for Clipsal s range of standard and slim line switch plates however types will vary 02 6 Do not cover with any material and install clear of curtains or drapes 02 7 Do not immerse any part of the dimmer in water or any other liquids 02 8 Always ensure dimmer is fully assembled before connecting to the power supply 02 9 Not suitable for use near flammable liquids vapors gases or in explosive environments 02 10 Regularly inspect the dimmer for any damage If found defective in any way immediately cease use and replace 02 11 There are no user maintainable components in this fitting The dimmer should never be opened 02 12 Do not attempt to modify this fitting in any way from the condition as supplied 03 PRECAUTIONS amp LIMITATIONS 03 1 LOCALTITY This iDimmer is suitable only for indoor locations 03 2 POSITIONING The dimmer can be positioned in any standard switch plate Optimised for Clipsal and HPM switch plates 03 3 INSTALLATIONS CLEARANCES Depending upon the installation of the switch plate position the dimming unit must be clear of all internal wiring and building materials The iDimmer does not create significant heat however precautions should be required to keep the rear of the switch plate clean and clear
4. als inside the wall cavity Make sure all wiring is hidden securely and safely Safety precautions above apply for selecting and drilling using a hole saw and other tools for making cavities 04 5 Fix the dimmer kit into position by 04 5 1 complete the wiring as per the below wiring diagram before installing the removable dimming cap 04 5 2 Press the fitting firmly into place and apply dimming cap to hold the dimmer securely into the switch plate If the dimmer does not fit securely change the switch plate Loose fitting dimmers can be a safety hazard 04 5 3 Have all electrical work asses by an Australian A grade licensed electrician Refer AS NZS3000 Wiring Rules Failure to comply with this will void manufacturers warranty and obligations 04 5 3 Check for safe installation Remove the Lock Out Tag Energise the circuit at the switchboard turn the switch to ON Test dimming capabilities only with a full circuit com au Line Voltage Power Low Voltage Source Line Dimmed Hot Electronic Transformer Dimmer The internal switch in this figure is not required in all systems 04 5 4Wiring diagram iDimmer leading edge dimming unit 05 CARE amp CLEANING 05 1 Do not use water to clean this product 05 2 To clean remove cap and use a lightly dampened cloth to clean cap and dimming collar Do not use excess water Consult an electrician if significantly soiled 05 3 Do not insert any object
5. e s instructions 8 5 All costs of a claim shall be met by the company however should the product that is the subject of the claim be found to be in good working order all such costs shall be met by the claimant 8 6 When making a claim the consumer shall forward this product to the point where it was purchased PO for internet orders for refund along with complete details of the date and place of purchase details of installing electrician name contact details and license number description of load and circumstances of malfunction within 28 days of the fault occurring 8 7 It is the retailer or wholesaler s responsibility to forward to the Company Product for credit to the nearest office of the Company with adequate particulars of the incident malfunction The product is to be returned securely packed and will not be accepted without the correct goods return authority GRA number being written on packing slip attached to the item and the claim 9 DISCLAIMER 9 1 The Company reserves the right to change the contents specifications or designs described in these instructions without notice and without obligation Please contact us to get the latest information before installation and use 9 2 This document subject to E amp O E
6. or substance into the dimmer or switch plate for cleaning purpose 06 REPLACEMENT PARTS amp LAMPS 06 1 There are no user maintainable items on this dimmer 06 1 1 Use only iGlobe supplied iDrive or replacement 12V LED Downlight drivers 7 TECHNICAL INFORMATION 7 1 500w 400 watt usable Leading edge dimming unit 7 2 Electrical Class 2 7 3 Electrical Safety Complies with AS NZS 60598 2 2 7 4 EMC Level 1 7 5 Complies with AS NZS CISPR15 7 6 Supply 180 265V 48 62Hz 7 7 Switch plate Clipsal standard and slimline HPM standard and slimline 8 WARRANTY STATEMENT 8 1 The benefits conferred herein are in addition to and in no way shall be deemed to derogate either expressly or by implication any or all other rights and remedies in respect to the company product which the consumer has under the Commonwealth Trade Practices Act or any other similar State or Territory Laws 8 2 The warrantor is The iGlobe Group Pty Ltd 8 3 This Lighting Products is guaranteed against faulty workmanship and materials for a period of five 5 years from the date of installation 8 4 The Company reserves the right at its discretion to either repair free of parts and labour charges replace or offer refund in respect to any article found to be faulty due to materials parts or workmanship 9 5 This warranty is expressly subject to the company product being installed wired tested operated and used in accordance with the manufactur
Download Pdf Manuals
Related Search