OPERATORS MANUAL - Streamline Supplies
Contents
1. E LN mur ar T gium or 7 r IPs Nu a Li Ta R gt PG 29 OPERATOR MANUAL After thoroughly cleaning the condenser fit the guard back in place 7 11 PERIODIC MAINTENANCE least once a year by a specialised technician This periodic check serves to ensure that all the components installed and the machine itself are maintained at a high level of safety 4 The machine must be periodically check at Any worn components must be replaced by an original spare part It is forbidden to use the machine when even SY only one of its components is faulty or worn lt Users are forbidden to perform periodic maintenance 8 SCRAPPING Electric and electronic equipment must be disposed of in accordance with european directive 2002 96 EC ouch equipment may not ne disposed of as normal municipal solid waste but must rather be separately collected to optimize recovery and recycling of the materials used to manufacturer them All products are marked with the crossed out wheeled bin EN symbol as a reminder of separate collection obligations Correct observance of all of the provisions for the disposal of end of life products will contribute to safeguarding the environment ARCTIC DREAM JNR OPERATOR MANUAL 9 TROUBLESHOOTING The machine does not turn on The main switch is off positioned on O Cap 6 Press the switch into position The machine is n2. Note This dotted line shows the components which are CN present in the machine according to the purchased model WIRING DIAGRAM FOR GRANITA MACHINE 1 TANK WITH ELECTRONIC THERMOSTAT 9230V 50HZ TS E VERSION HE o _ T250 mA for Tr 50VA E T32 mA for Tr23VA Note This dotted line shows the components which present in the machine according to the purchased model PG 32 ARCTIC DREAM JNR OPERATOR MANUAL WIRING DIAGRAM FOR GRANITA MACHINE 1 TANK BRS 230V 50HZ TS E VERSION e eu cg Estas e us ae ll 0 _ E 1630 BEN MEM t i do Ci AAH 1 E Reels cc WIRING DIAGRAM FOR GRANITA MACHINE 1 TANK 230V 50HZ TS V VERSION Note This dotted line shows the components which are 1 present in the machine PIN PN according to the purchased zal model me x TU de Lala mue o il PG 33 ARCTIC DREAM JNR OPERATOR MANUAL 2 BOWL GRANITA MACHINE WIRING DIAGRAM 115V 60HZ y 3 iH uo D Note This dotted line shows MERE ee the components which are TM P E present in the machine E Tu according to the purchased EE me model Tee OR ROM OR RON RR OR e mm A TEER RR EERE iH a gt Fc2 Note This
3. 7 1 1 EMPTYING GRANITA MACHINE GRANITA ONLY While the machine is on press the switch 3 amp into pos 0 to shut down the refrigeration system Then completely empty the bowl of it s contents pe n i A ud NOS Fig 38 After that put off the main mixer switch and unplug the machine SY C Fig 39 Qe PG 21 OPERATOR MANUAL 7 1 2 EMPTYING GRANITA MACHINE 1 GRANITA COOLER While the machine is on press the changeover switch into position O to shut down the refrigerator system YY Product After that put the main mixer switch and unplug the machine ARCTIC DREAM JNR 7 1 3 EMPTYING THE GRANITA MAKER 2 3 GRANITA For the sake of simplicity we will describe the operation for emptying the right hand tank only to empty the other tanks it is sufficient to carry out the same sequence of operations on their switches While the machine is on press the 3 amp into position 0 to shut down the refrigeration system a E d LF 2 2 e A A T T r ae 2 e e A gt e ra a a a 7 M a j PP PP e After that put both of the main switch and mixer switch and unplug the machine _ Fig AI OPERATOR MANUAL 7 1 4 EMPTYING GRANITA MAKER 2 3 GRANITA COLD DRINKS FRIDGE For the sake of sim
4. ws Each bowl is operated by two switches which must be positioned as follows Switch in position I Mixer is on 2 TANKS 222 a es s E Au 4 40 AINT C gt 3 TANKS ae a c Note The refrigerator system starts only if the switch is in position I mixer working PG 14 ARCTIC DREAM JNR OPERATOR MANUAL 6 6 STARTING GRANITA MACHINE 2 3 GRANITA COOLER For the sake of simplicity we will describe the operation for the right hand tank only for other tanks it is sufficient to carry out the same sequence of operations on their switches owitch in position is machine pel AE 2 TAN KS 2 The Bow of machines with a s cooling function is operated by means of an on off switch plus a refrigeration changeover switch which must be positioned as follows The switch in position I HUE power and mixer on Bo 2 TANKS 211 lt 222 GRANITA PG 15 ARCTIC DREAM JNR OPERATOR MANUAL To dispense COLD DRINKS TS E Note The refrigerator system starts only if the switch is in position I mixer working 6 7 STARTING THE GRANITA MAKER 2 3 ELECTRONIC THERMOSTAT Switch A is in position 1 Machine powered Switch B is in position I Machine operating To make SLUSH DRINKS GRANI
5. 4 1 PACKAGING The machine is shipped ready to use in a cardboard box The cardboard box comprises of a base and cover which are se cured together with two nylon straps DIMENSIONS AND OF in PE m om om ig B m Granita machine H 2 bow mee m m s 3 bowl Granta 99 76 Note The dimensions and weight of the packaging container are approx ee vu E Fig 9 4 2 CONVEYANCE AND HANDLING N Make sure that there is no one stationed within range of lifting and handling operations In difficult conditions specialized personnel should be appointment to oversee the movements of the machine Manual handling of the machine requires at least 2 people The machine must be moved in an upright position Only after every bowl has been emptied of product Lift the box carefully convey it avoiding routes with obstacles Pay attention to the overall dimensions and any parts sticking Out Warning do not make any additional cuts on the packing container The WARRANTY do not cover damage caused to the machine during its conveyance and handling The purchaser will bear the cost of repairing or replacing damaged parts 4 3 STORAGE A X Before the machines is placed in storage and whenever the machine is started up again after a period of storage It must be thoroughly cleaned and sanitized WARNING do not store more than two machines stacked on top of one and another If the machine is to
6. A4 Tank 2 probe short circuit 5 Tank probe disconnected A6 Tank 3 probe short circuit During operation the electronic thermostat shows the temperature of the product in the tanks cyclically showing the temperature of the product first in one tank then in the other every 3 seconds To see which tank is referred to with the temperature reading it is necessary to check which decimal point is being shown If the decimal point viewed is on the left the temperature reading refers to the tank 1 See figure 2 Fig 29 Decimal point If the decimal point viewed is in the centre the temperature reading refers to the tank 2 see fig 2 2 TANKS Fig 30 Decimal point If the decimal point viewed is on the right the temperature reading refers to the tank 3 see Fig 2 3 TANKS Fig 31 2 Decimal point sl Note If while using machine the electronic thermostat should switch iff suddenly to start it again press the jokey If the electronic thermostat should not switch on again switch off the machine and contact your nearest assistance centre N Important While using the machine the electronic thermostat must always be on so as to show the temperature of the product in the tanks PG 17 ARCTIC DREAM JNR OPERATOR MANUAL 6 8 ADJUSTING GRANITA CONSISTENCY The consistency of the Granita can be adjusted by means of the screw shown in the figure MAXI thicker consistency thinner consistency c
7. Il refrigeration system on cooling mode ENT PG 13 OPERATOR MANUAL 6 4 STARTING THE GRANITA MAKER 1 ELECTRONIC THERMOSTAT Switch A in position I Machine powered and mixer operating To make SLUSH DRINKS GRANITA Switch B in position Il Refrigerator system operating slush drinks granita To make COLD DRINKS switch in position Il Refrigerator system operating cold Drinks To disable the FRIDGE mixing only Deviator B in position 0 Refrigerator system off mixing only Setting the temperature set point Press the E key the display will read PrG Press the key pz the display will show the temperature Set point value Using thet keys it is possible to change the set point value from 0 C 10 KANT Aal a Fig 20 _ SE ps 3 seconds after the last key is pressed the setting is stored to the memory and the display will show the temperature of the product in the tank ALARMS Incase of probe failure the display will read A1 Programming and adjustment outputs will be disabled ARCTIC DREAM JNR OPERATOR MANUAL 6 5 STARTING A GRANITA MACHINE 2 3 GRANITA ONLY For the sake of simplicity we will describe the operation for the right hand tank only for other tanks it is sufficient to carry out the same sequence of operations on their switches switch in position I machine powered Au LP 3 TANKS Lum i x
8. in the tank Using the m keys it is possible to set the thermostat intevention temperature when the machine is operating in cold drinks mode Tank 1 Tank 2 Tank 2 Tank 3 D Refrigerator system diverter When set to O the refrigerator system is deactivated When set to I the refrigerator system operates in slush drinks mode When set to Il the refrigerator system operates in cold drinks mode 3 SAFETY 3 1 GENERAL SAFETY RULES Carefully read the whole instruction manual The connection to the electricity mains must comply with the current safety standards in the users country he machine must be connected to an electric outlet that is Compatible with the plug provider with the machine Of dimensions conforming to the data shown on the rating plate on the side of the machine Properly grounded Connected to a system provided with a different switch and circuit breaker The power cord must not be Allowed to come into contact with any kind of liquid danger of electric shocks and or fire Crushed and or brought into contact with sharp surfaces Used to move the machine Used if it shows any damage Handled with damp or wet hands Wound into a coil when the machine is on Tampered with DO NOT nstall the machine in a manner other than described in chap 5 nstall the machine in a place where it may be exposed to sprays of water Use the machine near inflammable and or explosive
9. light Mixer motor Bowl 1 mixer motor N Bowl 2 mixer motor Co Bowl 3 mixer motor O gt m Compressor motor MTx Timer motor lt o wn wn Co Fan motor V V N T C N T C 1 N T C 2 N T C 3 Bowl 1 Fan motor 1 N Bowl 2 Fan motor 2 Tank temperature probe Tank 1 temperature probe Tank 2 temperature probe Tank 3 temperature probe Sensor relay R s1 Bowl 1 sensor relay Bowl 2 sensor relay Bowl 2 sensor relay PG 37 ARCTIC DREAM JNR OPERATOR MANUAL LEGEND continued Item O PG 38 Streamline Supplies Pty Ltd 9 Joseph Baldwin Place Shepparton Victoria 3630 Ph 03 5831 5555 Fax 03 5821 3633 www streamlinesupplies com au
10. substances Leave plastic bags polystyrene nails etc within children s reach since they are potential sources of danger Allow children to play or stay near the machine Use spare parts other than those recommended by the manufacturer Make any technical changes to the machine Immerse the machine in any kind of liquid epray water on the machine to wash it PG 6 ARCTIC DREAM JNR OPERATOR MANUAL 3 1 GENERAL SAFETY RULES continued Use the machine other than as directed in this manual Use the machine when not in full possession of your mental and physical faculties under the influence of drugs alcohol etc nstall the machine on top of other equipment Use the machine is an explosive or aggressive atmosphere or in the presence of a high concentration of dust or oily substances suspended in the air Use the machine in a place where there is a risk of fire Use the machine to dispense substances that are not compatible with the machines specifications Before cleaning the machine make sure that it is unplugged do not clean the machine with gasoline and or solvents of any Kind Repair work may be performed only by a service center authorized by the manufacturer and or specialized trained personnel Do not obstruct the grill vents on the side of the machine Do not site the machine near heating equipment stoves and radiators In case of fire use carbon dioxide CO2 extinguishes Do not use water or powder extinguish
11. the function of enhancing the product s appeal by illuminating it with a diffuse light Before using the lighted lid make sure pL y it is correctly plugged turn the lid lamp on and off use the power SS WA switch provided on each lid m PG 18 ARCTIC DREAM JNR OPERATOR MANUAL 6 12 DISPLAY FOR PRODUCT TEMPERATURE IN THE TANK As an alternative to the electronic thermostat the machine can be fitted with one or more thermometers for the sole purpose of viewing the temperature of the product in the tank If the machine is equipped with a temperature display regularly check to make sure that the set temperature value and the actual temperature in the bowl are the same using a standard thermometer al Important note the thermometer is an optional feature for some markets according to current regulations it is installed as a standard component of the machine In one bowl machines the thermostat will show the temperature of the product contained in the bowl One machines with two three tanks 11 this views the temperature of the product in tank 1 2 this views the temperature of the product in tank 2 3 this views the temperature of the product in tank 3 p N Before undertaking any cleaning and maintenance of external machine components make sure that the main switch is positioned on 0 and that the machine is unplugged Before performing any cleaning and mainten
12. ICAL CONNECTION JIN mis job may be performed only by specialized technical personnel Before plugging in the machine make sure that the main switch is on 0 he purchaser is responsible for making the electrical connection The machine must be connected to the electricity mains by means of the plug fitted on the power cord Be sure to comply with he technical regulations and standards in force at the time of installation The data shown on the rating plate on the side of the machine N Warning the electrical outlet must be situated in a place easily within reach of the user so that no effort is required in order to disconnect the machine from the power supply when necessary If the power cord is damaged you must have it replaced either by the manufacturer or a specialized technician It is forbidden use extension cords of any type SLY To replace the original plug use adaptors PG 10 ARCTIC DREAM JNR OPERATOR MANUAL 6 OPERATION Before the machine may be started up for the first time specialized technical personnel must check that it functions properly 6 1 PREPARING THE PRODUCT N Warning Product may be poured into the bowl only when the machine is off and unplugged NEVER USE ONLY WATER Acqua Fig 12 Dilute the mix and CONCENTRATE with WATER in a suitable container following the manufacturers directions THE MIXTURE OBTAINED MUST HAVE A MINIMUM SUGAR CONTENT OF 1396 A lower conc
13. OR MANUAL 6 5 Starting up Granita machine 2 3 granita only 14 6 6 Starting up Granita Machine 2 3 granita cooler 15 6 7 Starting up Granita Machine 2 3 electronic thermostat 16 6 8 Adjusting Granita consistency 18 6 9 Dispensing Granita 18 6 10 Emergency situations 18 6 11 Lighted Lid 18 6 12 Display for product temperature in the tank 19 CLEANING AND MAINTENANCE PROCEDURES 20 7 1 Emptying the bowls 20 7 1 1 Emptying Granita Machine 1 granita only 21 7 1 2 Emptying Granita Machine 1 granita cooler 21 7 1 3 Emptying Granita Machine 2 3 granita only 22 7 1 4 Emptying Granita Machine 2 3 granita cooler 22 7 2 Disassembling the dispensing tap 23 7 3 Removing the bowl and lid 23 7 4 Washing and sanitizing the components 24 7 5 Reassembling the washed components 25 7 6 Sanitizing the evaporator 26 7 7 Cleaning the drip tray 26 7 8 Lighted Lid 27 7 8 1 Replacing the bulb 27 7 9 Replacing the temperature display battery 27 7 10 Cleaning the condenser 28 7 10 1 Cleaning the cond of a 1 bowl Granita Machine 28 7 10 2 Cleaning the cond of a 2 3 bowl Granita Machine 29 7 11 Periodic Maintenance 29 SCRAPPING 29 TROUBLESHOOTING 30 GRANITA M WIRING DIAGRAM 31 ARCTIC DREAM JNR OPERATOR MANUAL 1 GENERAL INFORMATION 1 1 MANUFACTURER The manufactures details are shown on the identification plate Illustrated on the first page of the manual 1 2 AUTHORIZED PERSONS Two types of persons may access the mac
14. TA Deviators D in position I Refrigerator system operating slush drinks granita To make COLD DRINKS Deviators D in position Il Refrigerator system is operating cold drinks To disable the FRIDGE mixing only Deviators D in position 0 Refrigerator system off mixing only Setting the temperature set point When the electronic thermostat is switched on press the E keys together and the display will read t1 With the cx key it is possible to scroll through the set points t1 and t2 machine with 2 tanks and 11 t2 and t3 machine with 3 tanks When the display shows the set point to be changed t1 t2 or t3 press the CA key to view the set point value lt is then possible to use the 3 E keys to set the set point value from 0 C 10 C The setting is stored to memory three seconds after the last key has been pressed The display returns to show 11 t2 t3 according to the set point that has been changed Press the E key until the display shows the temperature of the product in the tank 2 TANKS lt P 3TANKS z zz E _ m Eu PG 16 ARCTIC DREAM JNR OPERATOR MANUAL ALARMS Incase of probe failure the display will show the following alarm messages A1 Tank 1 probe disconnected A2 Tank 1 probe short circuit A3 Tank 2 probe disconnected
15. The adjustment may be made by hand or with the aid of a suitable flat tip screwdriver B d y P5 b JA 2 4 A 06 Aw A lu S SL e f lt 6 9 DISPENSING GRANITA To dispense the beverage use the tap lever ecl Regularly check the temperature of the product in the bowl using standard thermometer to make sure a that the product is always below the storage temperature Never disconnect the machine from the power supply or switch off the main switch when there is any product still to be consumed inside the bowl If the machine is not used continuously when used with milk based products it is nessecary to Spray sanitizer solution around the spigot area and on the spigot itself alternativly wash with a clean cloth and sanitizer or Dispense a small amount of the product from the spigot before dispensing the serving for the customer 6 10 EMERGENCY SITUATIONS WARNING in every emergency situation to shut down the machine firmly press the main switch into me position 0 Incase of freezing switch of the machine and contact a service center or specialized technician If a fire break outs the area must be immediately cleared to make way for trained personnel provided with suitable safety equipment Always use approved extinguishes never use water or substances of d dubious nature j hla Fig 34 6 11 LIGHTED LID AM ZA The lighted lid has
16. The battery has run out Replace the battery Section 7 9 temperature Probe fault Call a specialized technician The lighted lid does not work It is not plugged in properly Check that the plug is properly connected The switch is on Switch on the lid lamp using the switch Burnt out bulb Replace the bulb Section 7 8 The tap does not dispense Blocks of ice inside the bowl Switch off the machine allow the bowl contents to melt and check that the product has been correctly diluted If the machine malfunctions due to causes other than those listed in this table or the proposed remedies do not solve the problem contact a specialized technician PG 30 ARCTIC DREAM JNR OPERATOR MANUAL 10 GRANITA MACHINE WIRING DIAGRAM 1 BOWL GRANITA MACHINE WIRING DIAGRAM 115V 60HZ E mm cet Note This dotted line shows the components which are present in the machine according to the purchased E nn model il DPI Note This dotted line shows i the components which are OE present in the machine A c a according to the purchased 2 ni p model ua s B ede dixic seo gale ductu Sie RR E A na mise Neri wu Erud s eo nw si E wie a ane PG 31 ARCTIC DREAM JNR OPERATOR MANUAL 1 BOWL GRANITA MACHINE WIRING DIAGRAM 230v 50HZ WITH CYCLIC TIMER T250 mA
17. ance operation on the machine wear the personal protections gloves glasses etc which are recommended by the safety standards in force in the country where the machine is used When performing the cleaning and maintenance operations follow these instructions Wear protection accident proof gloves do not use solvents of inflammable materials do not use abrasive and or metal sponges to clean the machine and its components take care to avoid dispersing liquids in the surrounding area do not wash granita machine components in a dishwasher do not dry parts O the granita machine in a microwave or conventional oven do not immerse the machine in water do not expose the granita machine to direct sprays of water for cleaning use only lukewarm water and a suitable sanitizing agent complying with 21CRF1781010 in accordance with current regulations in the users country that will not risk damaging machine components on completion of work make sure that all protective covers and guards that have been removed or opened are set back in place and properly secured PG 19 ARCTIC DREAM JNR OPERATOR MANUAL Cleaning and sanitizing are operations that must be performed with utmost care and on a regular basis to guarantee the quality of the beverages dispensed and compliance with mandatory hygiene standards The minimum cleaning and sanitizing frequencies shall be in compliance with the regulation specified by federal states
18. bowl Granita machine with freeze mode only Granita machine 2 granita cooler identifies a 2 bowl Granita machine with a beverage cooling function Granita maker 3 granita identifies the Granita maker with 3 three tanks with the granita function only Granita maker 3 granita cooler identifies the Granita maker with 3 three tanks and cold drinks fridge PG 3 ARCTIC DREAM JNR 2 3 TECHNICAL DATA The technical data and features are listed below Model Granita Granita Granita machine 1 machine 2 machine 3 With 260 x 400 x 400 x 400 x 600 x 400 x standard lid 630 630 630 M 260 x 400 x 400 x 400 x 600 x 400 x Maximum Electrical Input W Dimensions LxPxH mm See rating plate on side of machine Operating voltage V Min 20 C Max 32 C ps E EG Operating temperature Capacity of each bowl Sound pressure level lt lt 0 dB acl NOTE The manufacturer reserves the right to LR make changes to the machine without notice accessories must be explicitly approved and IMPORTANT Any changes and or additions of implemented by the manufacturer Fig 2 OPERATOR MANUAL 2 4 CONTROL PANEL The machine controls are located on the side control panel GRANITA MACHINE 1 FIG 3 The following controls are on the panel A Main Switch is used to urn the machine and the gear motor that drives the product mixing auger bowl Turn off all machine functions Refrigerati
19. carry out maintenance operations on the lighted lid remove the lid from the machine and unplug it 7 8 1 REPLACING THE BULB The bulb must be replaced only when the main switch is in position 0 and the power cord is unplugged oeparate the two parts of the lid by removing the screws use a suitable screwdriver for this purpose Fig 68 T 1 x oo PG 27 OPERATOR MANUAL Remove bulb U from lamp holder T and fit a new bulb in its place 7 9 REPLACING THE TEMPERATURE DISPLAY BATTERY To ensure that it works properly each thermometer is powered separately by one 1 5V button battery code GPA76 Warning Only handle the thermometer with your hands Do not use any type of tool that could damage the thermometer To replace the battery proceed as follows Using a screwdriver remove the front cover ARCTIC DREAM JNR remove the used battery and fit a new one in its place taking care to comply with the polarities indicated a EHE um QT Qu EE om P A Um AA E ar E UE EE om QUO or n F r 2 1 k A A LI A i VV uu wu 3 5 ML 7 T L T o1 7 4 CT E LI LF LL 6 Y Note the cover must be closed by hand should you have encounter any difficulty in C9 closing the cover check weather the battery has been correctly positioned Cautionary notes Do not insert a used battery or one
20. dotted line shows E AN PN the components which are CU present in the machine oe axes to according to the purchased mor err model dins T PSS ee ere a ees PG 34 ARCTIC DREAM JNR OPERATOR MANUAL WIRING DIAGRAM FOR GRANITA MACHINE 2 TANKS WITH ELECTRONIC THERMOSTAT 230V 50HZ TS E VERSION S1 S2 Le Ly Us ud R2 o A b 7 IG 0 T250 mA for Tr 50VA T32 mA for Tr 3VA F l 1 1 1 e O O 0 022uF 0 022uF ij 1 275Vac 275Vac A tll 1 NTC rel 2 i Sj i lt NTC 2 EV1 EV2 lt IG 0 s F i mv mv DGB 1 DGB 2 i o 9 9 l lt lo id 1 19 hor N fi TN po _ a 3 af e n n n n n n g n l1 n VAS Wiles A do 13 12 1 ral Fez Lo ecb Ms ums ota ud EVI 2 1 ET ec c wo ere cm m IR o9 Note This dotted line shows the components which present in the machine according to the purchased model PG 35 ARCTIC DREAM JNR OPERATOR MANUAL WIRING DIAGRAM FOR GRANITA MACHINE 3 TANKS WITH ELECTRONIC THERMOSTAT 230V 50HZ TS E VERSION S1 S2 N N Bicis Rz 224 IG E 1 l FIK NE M2 Es EET 4 8 44 0 022uF 275Vac NTC 4 Fel 53 R3 EE Note This dotted line shows the compone
21. entration may damage the augers and or gear motors NEVER INTRODUCE HOT LIQUIDS with temperatures exceeding 25 C MAXIMUM LEVEL S 3 Y y Y gt M CS i SS Sx XQ SS A gt Fig 13 c Pour the product into the bowl taking care not to overfill beyond the max level indicated PG 11 ARCTIC DREAM JNR OPERATOR MANUAL de After pouring the product into the bowl close the lid on top of the bowl N Warning never switch on the machine if the lid is missing Before removing the lid switch off the machine and unplug it au There are some moving parts inside the bowl which may cause injuries turn off and unplug the machines before carrying out any operations inside the bowl 6 2 STARTING UP GRANITA MACHINE 1 GRANITA ONLY The bowl of a standard machine is operated by two switches which must be positioned as follows The switch is in position T machine powered and mixer on ISSN PG 12 ARCTIC DREAM JNR 6 3 STARTING A GRANITA MACHINE 1 GRANITA COOLER The bowl of machines with a beverage cooling function is operated by means of an on off switch plus a refrigeration switch which must be positioned as follows Switch in position I machine powered and mixer on NIMNN C To dispense GRANITA dn position I refrigeration system on freeze mode Fig 18 To dispense COLD DRINKS Changeover switch in position
22. er so that it meets the seat provided E in the bowl Using the Vaseline provided lubricate the seal A in the areas shown in figure 60 ud Important note Always check the seal integrity X should it be worn replace with a new one Replace seal A once a year Apply seal B lubricating the entire surface indicated by the arrows with Vaseline Fig 61 PG 25 ARCTIC DREAM JNR Press the bowl downward until it engages the surface as shown in the figure gt Fig 65 Follow these instructions to refit the tap 1 Adequately lubricate the plug X and OR Y using Vaseline supplied 2 Introduce the tap spring and body from the lower part of the tap 3 Introduce the lover and fix it in its sear while keeping the tap body pressed upwards 4 Introduce the pin F without moving the tap lever Fig 66 Na Note Correctly install the components as shown in the figure Note Failure to lubricate the plug and OR may cause product to leak from tap for model with lighted lid only Connect the lid by inserting the plug into the machine outlet OPERATOR MANUAL 7 6 SANITIZING THE EVAPORATOR Before starting up the machine you must sanitize the evaporator Proceed as follows 1 Prepare the sanitizing solution in a suitable container following the directions provided on the package of the sanitizing product 2 Put the sanitizing solution into the bowl 3 Allow time
23. erator system is activated for the production of slush drinks When set to Il the refrigerator system is activated for the production of cold drinks F Tank 2 refrigerator system driver When set to 0 the refrigerator system is deactivated When set to I the refrigerator system is activated for the production of slush drinks When set to Il the refrigerator system is activated for the production of cold drinks G Tank 3 refrigerator system driver When set to 0 the refrigerator system is deactivated When set to I the refrigerator system is activated for the production of slush drinks When set to Il the refrigerator system is activated for the production of cold drinks 2 TANKS 3 TANKS ef 5 I O 9 1 Es I 9 mes EN d m nme y AM E J 2 TANKS 3 TANKS OMM s 8 m E a ollo DI a mE Fig6 ARCTIC DREAM JNR OPERATOR MANUAL GRANITA MACHINE 2 3 ELECTRONIC THERMOSTAT SLUSH DRINK COLD DRINKS FIG 8 The machine controls are located on the panel on the side 2 TANKS 3 TANKS A Main Switch this serves to supply disconnect power to the whole machine B Mixing Switch this serves to switch the gear motor that drives the spiral on and off C Electronic thermostat display his shows the temperature of the product
24. ers In the event of improper use all warranty rights will be forfeited and the manufacturer will accept no Ux liabiity for injury or damage to persons and or property he following are to be considered improper use Any use other than the intended use and or with methods other than those described here in Any operation on the machine that is in contrast with the directions provided herein Any operation on the machine that is in contrast with the directions provided herein Use of the machine after any components have been tampered with and or safety devices have been changed Use of the machine after it has undergone repair with components not authorized by the manufacturer Outdoor installation of the machine 3 2 STOP FUNCTIONS The machine is shut down by turning off the main switch 3 9 PLATES NONE OF THE PLATES OR LABELS APPLIED ON THE MACHINE MUST BE REMOVED COVERED OR DAMAGED ESPECIALLY THOSE RELATING TO SAFETY 4 HANDLING AND STORAGE 40 All the operations described in chapter 4 may be carried out exclusively by technicians who are also specialized in the lifting and handling of packed or unpacked machines They must organise all the operational sequences and use suitable equipment according to the characteristics and weight of the object to be handled and in strict com pliance with the applicable regulations currently in force PG 7 ARCTIC DREAM JNR OPERATOR MANUAL 4 HANDLING AND STORAGE continued
25. for sanitizing solution to act see directions on product package 4 Empty the tank of sanitizing solution by opening the tap Then thoroughly rinse the bowl and evaporator to eliminate residues of sanitizing solution Warning The bowl must be rinsed of Sanitizing solution as directed on the package N of the sanitizing product and in accordance with the hygiene regulations currently in force in the users country 7 CLEANING THE DRIP TRAY The drip tray should be emptied and cleaned daily asl Note all of the drip trays present in the machine should be cleaned Holding the drainage hose firmly life the tray with the grid on top of it and pull it out li EAE 1 LILI Wash the tray and grid separately with lukewarm water x TN pr qm ics A E i Dry all components Reposition the grid on the top of the tray Position the drainage hose in the opening provided Fit the tray back in place and press down to secure it to the machine PG 26 ARCTIC DREAM JNR 7 8 LIGHTED LID Maintenance of the lighted lid must be 4 entrusted solely to a specialized technician who must organize all of the operational sequences and use suitable equipment in strict O compliance with all applicable regulations currently in force The operator is forbidden to disassemble any lid component Warning Only handle the lids with your hands Do not use any type of tool that could damage the lid or its components To
26. g and sanitizing operation of the lid remove it from the machine as described in the previous chapter To clean the lighted lid correctly proceed as follows 1 Using a damp cloth first wipe the bottom part of the lid in contact with the product 2 Using a clean damp cloth wipe clean the whole outer part Fig 57 Outer part j 2 5 j A 4 C e i EA P f AN Dos 1 a Bottom part 3 Using a sponge dipped in sanitizing solution sanitize the bottom part of the lid 4 Allow to act for 30 min 5 Rinse twice or more only the bottom part with a clean oponge soaked in fresh water 6 Place the lid on a clean surface and dry it first first dry the bottom and them the outer part by means of a clean cloth 7 Set the lid back in place only after having cleaned and sanitized the bowl It is forbidden to wash and or sanitise the lid while it is installed in the machine Min and sanitize the id e and resting surface Sres PG 24 ARCTIC DREAM JNR OPERATOR MANUAL 7 5 REASSEMBLING THE WASHED COMPONENTS Introduce the auger engaging head C with shaft D All of the washed and sanitized components must be zl Note Rotate the auger to engage it carefully reassembled Some components must be adequately lubricated in order to ensure that they work efficiently Apply the seal A on the auger as show in figure 59 oet the bowl back in place slightly raise head C of the aug
27. hine for different purpouses User person who has adequate techinical training to prepare the products the machine uses to dispense Granita in observance of current standards of hygiene After reading this manual he will be capable of Carrying out normal product loading and or replacment operations Properly dispensing the products Cleaning and sanitizing the machine Specialized Technician person who has examined this manual and has specific training in the installation use and servicing of the Granita machine He must be able to carry out repairs in the event of serious faults and be well acquainted with this manual and all the information rations regarding safety He must be able to understand the contents of the manual and correctly interpret drawings and diagrams He must be familiar with the most important sanitary accident prevention technological amp safety standards He must have specific experience in servicing Granita machines He must know how to behave incase of emergency where to find individual safety equipment and how to use it properly Persons who do not meet the above requirements must not be allowed to use the machine 1 3 LAYOUT OF THE MANUAL he purchaser must be very careful to read the information contained in this manual 1 3 1 PURPOSE AND CONTENTS The purpose of this manual is to provide the Purchaser with all the necessary information regarding the installation mainte nance and
28. ing out any operation PG 2 ARCTIC DREAM JNR OPERATOR MANUAL 2 MACHINE DESCRIPTION 2 1 USE OF THE MACHINE The professional machine that you are using is designed to make slush drinks and cold drinks If used with dairy based products and or when envisaged by law in according to the type of product used it must be equipped with the optional extra of the temperature gauge for the product in the bowl It is also obligatory to comply with the current regulations and stan dards concerning the products used Depending on the model you have chosen the machine may include one or a combination of the following functions Beverage cooling Illumination of the product in the bowl Automatic stop of the auger when the lid is removed Display of the temperature of the product in the bowl 2 2 MAIN COMPONENTS The main components making up the machine will vary according to the machine purchased They comprise of A Bowl Lid B Thickness regulator C Bowl D Control panel E Electronic thermostat F Feet G Drip Iray H Grid Product dispenser L Product dispensing lever yi Ut To make the instructions easier to read the following abbreviations are used herein Granita machine 1 granita identifies a 1 bowl Granita machine with freeze mode only Granita machine 1 granita cooler identifies a 1 bowl Granita machine with a beverage cooling function Granita machine 2 granita identifies a 2
29. ita bowl is fundamental to ensure correct machine cleaning and sanitization To remove a bowl correctly proceed as follows 1 off the lid for model with lighted lid remove the plug from the outlet placed on the machine protect it and make sure it does not touch any liquid Fig 53 ARCTIC DREAM JNR 3 Remove the bowl from its seat by pushing and tapping lightly on the rear part Fig 55 L m De y DEIN a Ln Low Qi l s TA ik 7 4 WASHING AND SANITIZING THE COMPONENTS All of the previously disassembled and removed components must be thoroughly washed and sanitized Use the sanitizing product as directed on N the product labels To carry out this procedure correctly proceed as follows 1 Fill a sink with detergent and hot water 50 60 2 Wash the disassembled components with the detergent 3 Rinse with hot water making sure no traces of lubricants remain 4 Fill another sink with sanitizing solution prepared in water 5 Soak the disassembled components in the sanitizing solution use the sanitizing product as directed on the package labels 6 Rinse with clean water 7 Place the components on a clean surface and dry them Using a damp cloth clean all product residue from the evaporator Wash and sanitize the lid OPERATOR MANUAL Warning do not submerge lids equipped N with lighting in any type of liquid Before starting the cleanin
30. n Switch This serves to supply cut off the power to the whole machine B Tank 1 mixer switch This serves to switch the gear motor that drives the product mixing spiral in tank 3 on and off C Tank 2 mixer switch this serves to switch the gear motor that drives the product mixing spiral in tank 1 on and off D Tank 3 mixer switch this serves to switch the gear motor that drives the product mixing spiral in tank 3 on and off E Tank 1 refrigerator system switch this serves to switch the refrigerator system of tank 1 on and off F Tank 2 refrigerator system switch this serves to switch the refrigerator system of tank 2 on and off G Tank 3 refrigerator system switch this serves to switch the refrigerator system of tank 3 on and off PG 5 OPERATOR MANUAL GRANITA MACHINE 2 3 GRANITA COOLER FIG 7 The following controls are on the panel A Main Switch it is used to switch on off the power supply to the whole machine B Tank 1 mixer switch this serves to switch the gear mo tor that drives the product mixing spiral in tank 1 off and on C Tank 2 mixer switch this serves to switch the gear mo tor that drives the product mixing spiral in tank 2 off and on D Tank 3 mixer switch this serves to switch the gear mo tor that drives the product mixing spiral in tank 3 off and on E Tank 1 refrigerator system driver When set to 0 the refrigerator system is deactivated When set to I the refrig
31. nts which are present in the machine according to the purchased model 3 BOWL GRANITA MACHINE WIRING DIAGRAM 115V 60HZ Note This dotted line shows the components which are present in the machine according to the purchased model PG 36 ARCTIC DREAM JNR OPERATOR MANUAL rri rri e Description CPU Electronic card D G B D G B 1 D G B 2 D G B 3 Refrigerator system diverter Bowl 1 Granita cooler refrigeration changeover switch bowl 1 refrigeration system Bowl 2 Granita cooler refrigeration changeover switch bowl 2 refrigeration system Bowl 3 Granita cooler refrigeration changeover switch bowl 3 refrigeration system lt Gas solenoid valve EV1 Bowl 1 gas solenoid valve EV2 EVs Bowl 2 gas solenoid valve Bowl 3 gas solenoid valve Transformer fuse e ccm 2 Slush hardness adjustment limit switch F02 F63 FGIX Bowl 1 granita hardness adjustment limit switch Bowl 2 granita hardness adjustment limit switch Bowl 3 granita hardness adjustment limit switch Timer limit switch Transformer fuse Main switch I G M Main switch Mixer motor Bowl cover light switch Bowl 1 cover light switch 12 13 IM1 Bowl 1 mixer motor switch M2 IM3 Bowl 3 mixer motor switch Bowl 2 cover light switch Bowl 3 cover light switch Main switch Bowl 2 mixer motor switch Bowl cover light L L1 L L2 Bowl 1 cover light Bowl 2 cover light Bowl 3 cover
32. of a different type If the machine will remain unused for a long period remove the battery from its compartment and store it in a suitable place In normal conditions of use a new battery will have a life of about one year Spent batteries must be disposed of in accordance with the laws in the users country 7 10 CLEANING THE CONDENSER The condenser may be cleaned solely by a specialized technician who must organize all 4 of the operational sequences and use suitable equipment in strict compliance with the applicable regulations currently inforce O Periodically clean the condenser situated inside the machine Warning Before proceeding to clean the Condenser switch off and unplug the machine A dirty condenser will impair the performance of the machine To access the condenser remove the safety guards OPERATOR MANUAL It is forbidden to use the machine when even e only one panel front rear or side is not set ws properly in place It is prohibited for the operator to clean the condenser 7 10 1 CLEANING THE COND OF A 1 BOWL GRANITA MACHINE CONFIGURATION 1 Remove the side safety guards taking out the screws securing them to the machine TAA VVUVVVVVVNVA Remove the rear guard after taking out the screws securing it to the frame the screws are situated on the left and right sides TUN Fig 73 After removing the guard use a dry brush to remove the dust that has built up
33. on on off switch it is used to turn the refrigerator system on and off Es GRANITA MACHINE 1 GRANITA COOLER FIG 4 The following controls are on the panel A Main Switch is used to Turn on the machine and the gear motor that drives the product mixing auger in bowl Turn off all machine functions B Refrigeration on off switch In position O the refrigeration is off In position I the refrigeration system is in the freeze mode granita n position Il the refrigeration system is in the cooling mode cold drinks Fig 4 PG 4 ARCTIC DREAM JNR FROZEN DRINK MACHINE 1 ELECTRONIC THERMOSTAT SLUSH COLD DRINKS FIG 5 he machine controls are located on the panel on the side A Main Switch this serves to control he machine on the spiral movement he switching off of all functions on the machine B Refrigeration system diverter position O the refrigeration system is deactivated n position T the refrigeration system operates in slush drinks mode n position Il the refrigeration system operates in cold drinks mode C ELECTRONIC THERMOSTAT DISPLAY his shows the temperature of the product in the tank Using the x3 E keys it is possible to set the thermostat intervention temperature when the machine is operating in cold drinks mode GRANITA MACHINE 2 GRANITA FIG 6 The following controls are on the panel A Mai
34. or local regulatory agency having jurisdiction The bowl must be cleaned and sanitized at least once a day and in any case in compliance with the current hygiene regulations in the country of use These operations need to be performed more frequently if demanded by the characteristics of the product used for more details contact the product supplier If the machine is not used continuously throughout the day wipe the dispensing tap area and product outlet pipe with a clean cloth and sanitizing fluid as illustrated in the figure below ga 3 Ll lt i 2i The stainless materials plastic and rubber used to manufacture said parts as well as their particular shape gt make them easy to clean but do not prevent build up of germs and mould in the event of inadequate cleaning It is forbidden to clean or service the machine when it is unplugged in and the main switch is lt 7 positioned on T 7 1 EMPTYING THE BOWLS Before the bowl may be cleaned it must be emptied of the previously prepared product If the bowl is to be cleaned prior to the first use of the machine it need not be emptied in such a case refer directly to section 7 2 For the sake of simplicity we will only describe how to empty the machine without electronic thermostat and temperature display For models with electronic thermostat and temperature display the procedure listed here below applies PG 20 ARCTIC DREAM JNR
35. ot plugged in Insert the plug in a suitable outlet The tap leaks liquid leaks from below The tap plug is not lubricated Fig 65 Lubricate the plug and OR The plug is defective Replace the plug The tap leaks liquid leaks from above The OR is defective Replace the OR The OR is not lubricated Fig 65 Lubricate the plug and OR Product leaks from the rear part of the The bowl is not fit correctly in place Par 7 5 Check the positioning of the bowl bowl The bowl seal is not lubricated Fig 60 Lubricate accordingly The seal is defective Replace the seal The auger does not turn The switch is positioned on Cap 6 Press the switch into position Blocks of ice inside the bowl owitch off the machine allow the bowl contents to melt and check that the product has been correctly diluted The machine does not make granita The switches are off Cap 6 Press the switch into position l The machine is near sources of heat Install the machine in a suitable place There is insufficient ventilation The condenser is dirty Par 7 10 Call in a specialized technician to clean the condenser The consistency has not been regulated correctly Par 6 6 Correctly regulate the consistency The auger is noisy The front seal has been applied incorrectly Fig 57 Check that the seal is applied correctly The seal is not lubricated Fig 60 Lubricate the seal accordingly The thermometer does not indicate the
36. over time with use L b m NA Fig 74 gt gt TO A y KK m 1 f y A E a n IN BT v y M TT After thoroughly cleaning the condenser fit all the guards back in place PG 28 ARCTIC DREAM JNR CONFIGURATION 2 Remove the locking knobs from the rear door remove the door and clean the condenser using a dry brush Lad AA Fig 75 N 22 iR VV Wy y Pi EEN e JE a A PERA i i fii VE V FF nol y E For FE er on pu y eo T DECC Pu P E Fo pr lr y Hg LE F p i ror ry _ y p y f f uA Lari y ERAS ri rj j WAY i Pl in for rgo hg gl if P und HY Y E After carefully cleaning the condenser refit the rear door 7 10 2 CLEANING THE CONDENSER ON THE GRANITA MAKER 2 3 TANKS The safety guards may be secured with screws or clips If the guard is fastened with screws use a suitable screwdriver if the guard is fastened with clips it may be removed by hand without the aid of any tools Fig 76 After removing the guard use a dry brush to remove the dust that has built up over time with use J a E ur zr Bac reus 1 ru A rc I E a e z pr ul 1 e
37. plicity we will describe the operation for emptying the right hand tank only to empty the other tanks it is sufficient to carry out the same sequence of operations on their switches While the machine is on press the changeover switch NS into position to shut down the refrigeration system AA d gt e p He P UT 1 Y y e L 5 Lt AREA A Ps i e Ps a APA SS e d A J J ra ENS PAS VS SR I N E A ANGA 2 The completely empty the bowl of its contents After that put both of the main switch and mixer switch and unplug the machine AL E E Fig 48 ARCTIC DREAM JNR 7 2 DISASSEMBLING THE DISPENSING TAP Before removing the bowl it is recommended to disassemble the tap after cleaning the tap must not be reapplied until the bowl has been correctly positioned in its seat Follow these instructions to disassemble the tap 1 Remove pin F without moving the tap lever A AU y 2 Take out the lever UAA Fig 50 PG 23 OPERATOR MANUAL These components may be placed in a basin containing hot water approx 50 C they must be treated as described in section 7 4 eins Fig 52 Never disassemble the tap if the product or any i other liquid is present inside the bowl 7 3 REMOVING THE BOWL AND THE LID Removal of every Gran
38. quipment must be disposed of in accordance with European Directive 2002 96 EC ouch equipment may not be disposed of as normal municipal solid waste but must rather be separately collected to optimize recovery and recycling of the materials used to manufacture them All products are marked with the crossed out wheeled bin m symbol as a reminder of separate collection obligations Correct observance of all of the provisions for the disposal of the end of life products will contribute to safeguarding the environment ARCTIC DREAM JNR GENERAL INFORMATION 1 1 Manufacturer 1 2 Authorized Persons 1 3 Layout of the Manual 1 3 1 Purpose and contents 1 3 2 Who must read the manual 1 3 3 How to keep the manual 1 3 4 Symbols used MACHINE DESCRIPTION 2 1 Use of machine 2 2 Main components 2 3 Technical Data 2 4 Control Panel SAFETY 3 1 General Safety rules 3 2 Stop Functions 3 3 Plates HANDLING amp STORAGE 4 1 Packaging 4 2 Conveyance and handling 4 3 Storage INSTALLATION 5 1 List of accessories provided 5 2 Installation Positioning 5 3 Disposal of packing materials 5 4 Electrical connection OPERATION 6 1 Preparing the product 6 2 Starting up Granita Machine 1 granita only 6 3 Starting up Granita Machine 1 granita cooler 6 4 Starting up Granita Machine 1 electronic thermostat OPERATOR MANUAL O OO OO J OQ GOD C C GD PB N ND h m om CJ GQ N C CO ARCTIC DREAM JNR OPERAT
39. rances must be left around the machine to enable personnel to work without any constraints and also to leave the work area immediately incase of need Figure 9 shows the minimum clearances for installation The figure indicated the spaces required for accessing The control panel on the right side Machine parts so that they may be services in the event of a fault N un 25 cm N N X 10 inches ET P b x bs N o E O TN ADO W ON 150 A b Vd J 60 inches Fig 11 a d PG 9 ARCTIC DREAM JNR OPERATOR MANUAL 5 2 INSTALLATION POSITIONING continued al Note Clearance of 25mm 10 inches must be left at the top After positioning the packing container in the vicinity of the installation site proceed as follows 1 Cut the straps securing the box 2 Lift the cardboard box 2 Then lift the machine and position it on the prepared site asl Before the machine is used for the first time its components must undergo thorough cleaning and the parts that will come into contact with the Granita must be sanitized for further details see the relevant section herein 5 3 DISPOSAL OF PACKING MATERIALS After opening the box make sure to separate the packing materials according to type and dispose of them in accordance with the current regulations in the users country We recommend keeping the box for future conveyance or transport 5 4 ELECTR
40. remain unused for a long period of time due precaution must be taken with respect to the place and duration of storage Store the machine in a closed place PG 8 ARCTIC DREAM JNR OPERATOR MANUAL 5 INSTALLATION All of the operations described in chapter 5 may be carries out exclusively by specialized technicians who 4 must be organized all the operational sequences and use suitable equipment in strict compliance with the applicable regulations currently in force The machine must be installed indoors in a well lit and well ventilated room with a form solid level floor Slope less than 29 The machine is of the attended type and must be installed in places where it can be monitored by trained personnel Warning it is forbidden to install the machine in a place where it may be reached touched and or operated lt persons other than those specified in section 1 2 The machine may only operate in places with an ambient temperature ranging between 20 and 32 5 1 LIST OF ACCESSORIES PROVIDED Vaseline to lubricate all of the parts indicated in this manual after washing and sanitization operations 5 2 INSTALLATION POSITIONING he installer must check that he site has been duly prepared for machine installation The surface the machine will be installed on if firm flat and solid The room is adequately lit ventilated and hygienic and an electric outlet is within easy reach JA clea
41. st another copy should be immediately requested from the manufacturer or authorized distributor in the users country ds 1 3 4 SYMBOLS USED N GENERAL DANGER WARNING It indicates a danger which may also place the user at mortal risk In such case utmost care is required and every precaution must be taken in order to operate safely DANGER OF ELECTROCUTION It warns the personnel concerned that the operation described may result in an electric shock unless all the necessary safety precautions are taken a NI PROHIBITED This symbol is used to indicate operations that must absolutely be avoided since they created hazards for the user and any other individuals present in the vicinity G9 4 SPECIALIZED TECHNICIAN It identifies operations that may be performed only by a qualified technical personnel IMPORTANT It indicated a cautionary note a note about key functions or useful information Very close attention should be paid to the proportions of text marked with this symbol DO NOT EXTINGUISH FIRES WITH WATER The presence of this symbol warns against attempting to extinguish fires with water or any other substance PERSONAL PROTECTION When this symbol appears alongside a description it means that personal safety equipment must be used as there is an implicit risk of accidents A MOVING MACHINE PARTS It identifies the danger due to moving parts existing in the machine Turn off the machine before carry
42. supplies NM z f II TI WY F di p j y P a yy ny Uf fi Mf Uf hy Uf prp Hn O O o 0 o mj 0 gt gt gt ri if Yi JO P jd Fi ll i Ti A Yi fff MY f Ji 0 Ju i y UU to ca E 7 ARCTIC DREAM JNR MACHINES 5 ef M f du TE d Pda 373 y 3 Y pu 0 Y LA Yi SMM i A M AN al UU i a E p4 Vu y For machines with CE marking The manufacturer hereby declares under its own exclusive responsibility that the machine named in this manual see the plate on the cover of the manual conforms to the essential requirements of the following directives 2006 42 CE Machinery Directive 2006 95 CE Low Voltage Directive 2004 108 CE EMC Directive e 97 23 CE PED Directive 2004 1935 CE Regulation Materials and items in contact with foodstuffs he rating plate on each machine bears the following information XXXXXXXXXX XXXXXXXXXX E XXXXXXX X Hz W Manufacturer s name Machine model Year of production serial number CC Electrical specifications Type and quantity of coolant gas DISPOSAL Electric and electronic e
43. use of the Granita machine Before carrying out any operation on the machine users and specialized technicians must carefully read the instructions here in Should you have any doubts as to the correct interpretation of these instructions contact the manufacturer to request the necessary explanations You should not carry out any type of operation until you have read and thoroughly understood the contents of this manual PG 1 ARCTIC DREAM JNR OPERATOR MANUAL 1 3 2 WHO MUST READ THE MANUAL his manual is aimed at users and specialized technicians Users must not attempt to carry out any operations restricted to qualify technicians The manufacturer will not be liable for any damage or injury caused as a result of failure to comply with this rule he instruction manual is an integral part of the product purchased and must therefore be handed over to any subsequent Owners 1 3 3 HOW TO KEEP THE MANUAL This instruction manual must be kept in the immediate vicinity of the machine Due precautions should be taken to ensure that the manual is maintained intact and legible over time Use the manual in such a way as to avoid damaging any of it contents Do not for any reason remove tear or re write parts of the manual Keep the manual in a place that is protected against humidity and heat in order to preserve the quality of the print and legibility if all its parts yi If the present instruction manual is damaged or lo
Download Pdf Manuals
Related Search