Demo Node User Guide
Contents
1. The magnet faces are polarized to allow two Demo nodes to attach back to back Take care to ensure that the magnets have suitable adhesion to a surface to avoid them falling on someone who may be underneath d USB Connector The USB connector supplies 5V power to external devices e g lamps fans etc Once connected to such an electrical device the Demo Node serves as an Organic Response Enabled power board which responds to the occupancy information it receives and turns the power to the external device on or off as required e RJ45 Connector Not currently supported by the firmware but in future will allow connection for data collection f Mini USB Power Inlet Connector amp Battery Charging Status LEDs This mini USB connection is used to recharge the Demo Node battery from a USB power source e g laptop computer On connection of the USB cable the top LED will glow red to indicate that battery charging is in progress When the battery is fully charged the bottom LED glows green Typically a fully flat battery will take about 8 hours to fully recharge At maximum brightness the battery will give a run time of approximately 2 hours g LED Indicators Once turned ON the Sensor Node will flash its dome red for 2 seconds to confirm activation When the Demo Node is switched on the top LED indicator glows blue when the battery is low the bottom LED glows orange h ON OFF Switch This slide switch turns the Demo Node on or off ORG2. receipt of the relayed message Note the dome of the relaying node will flash red for 60 seconds to indicate it is sending the signal The dome of any node that receives the signal will remain solid red for a period of 60 seconds indicating that it has both received the signal and re communicated it to it s neighbours If you have any questions or concerns after following all directions in this document please contact organic response for further support E info organicresponse com au Australia Europe T 61 3 9486 9823 T 31 20 893 4149 ORGANIC RESPONSE PTY LTD ABN 46 151 527 098 47 Little Hoddle Street Richmond Vic 3121 61 3 9486 9823 organicresponse com au PAGE 4 OF 6
3. ANIC RESPONSE PTY LTD ABN 46 151 527 098 47 Little Hoddle Street Richmond Vic 3121 61 3 9486 9823 organicresponse com au PAGE 2 OF 6 Q organic response 2 USING THE DEMO NODE A Demo Node is designed to be used as a simulation of a fully functional Organic Response enabled luminaire when demonstrating Organic Response Lighting Controls A combination of multiple Demo Nodes with one or more Organic Response enabled luminaires provides a powerful compact portable and easily deployed demonstration of a fully functioning Organic Response installation a A Single Demo Node A single Demo Node can powerfully demonstrate to anyone anywhere the ease with which a user can adjust and optimize the performance of an Organic Response Enabled luminaire e Adjusting the light output DIM amp DIM e Setting the Max Light e Setting the Dwell Time e Changing the Personality e Calibrating daylight dimming Whilst you can effectively perform all optimisation functions on the Demo Nodes it makes sense To demonstrate those settings whose impact is immediately visible to the audience e g changing Light Levels and Dwell Times rather than settings which are only visible in the context of a large community of Organic Response enabled luminaires e g Personality settings or that only respond to significant changes in ambient light e g daylight dimming calibration b Multiple Demo Nodes When one or more Demo Nodes or alternatively an
4. For more information on downloading the remote app and or acquiring the dongle please visit organicresponse com au marketing resources 1 WHAT IS A DEMO NODE A Demo Node is a fully functioning portable Organic Response Enabled luminaire fitted with a dimmable LED light panel and Sensor Node Two or more Demo Nodes allow for a full demonstration of the Organic Response control system and its unique form of Distributed Intelligence communication A Demo Node kit comprises two Demo Nodes and a charge cable in a protective carry case Each Demo Node comprises the following e Dimmable backlit LED panel e Organic Response Sensor Node e Rechargeable battery e USB power outlet e Magnetic contacts underneath Q organic response Figure 1 Demo Node amp Features Q Backlit Dimmable LED panel Simulates an Organic Response Enabled light source with light output controlled by the integrated Senor Node The panel may be dimmed to any level between 10 and 100 The panelis representative of a luminaire and is not intended for any functional task illumination b Sensor Node Integrated Organic Response Sensor Node Together with the dimmable LED panel it operates in exactly the same way as any Organic Response Enabled luminaire c Underside panel Magnetic Contacts for Surface Mounting Four magnets are mounted in the base of each Demo Node enabling attachment to magnetic surfaces like an existing luminaire frame or ceiling brackets
5. Response Enabled luminaire The dome of the receiving Sensor Node will blink red in acknowledgement of each of the 30 signals it successfully receives This process effectively illustrates how two Sensor Nodes communicate with each other without any need to set up or commission these Communications ORGANIC RESPONSE PTY LTD ABN 46 151 527098 47 Little Hoddle Street Richmond Vic 3121 61 3 9486 9823 organicresponse com au PAGE 3 OF 6 Q organic response For added effect take your hand and place it over the transmitting Sensor Node This physical barrier will prevent the transmission of IR communications and you will observe that the dome of the receiving node will stop flashing Remove your hand and communications should continue as normal To indicate the limited range of the infrared proximity limited communication take the transmitting node and increase the distance between it and the receiving node As the distance increases the likelihood of communication reduces and you will find that some signals will not be received By increasing the distance further you will observe the blinking move through intermittent to no blinking at all Moving closer again to the other node will resume Communications and blinking should again be obvious Note The recommended maximum distance between Sensor Nodes installed in the ceiling is 3m Site Application Test To test the suitability of Organic Response to an existing office soace
6. other Organic Response Enabled luminaire is added to a single Demo Node the resultant system can be used to demonstrate the communications that occur between Sensor Nodes Note Care should be taken to avoid placing the demo nodes near significant sources of infrared interference including existing light fittings that contain ballasts that may generate signals which can negatively affect the infrared performance of the Organic Response system Also ensure that any luminaire being controlled by the demo node unit does not directly illuminate the demo node sensor node as this may interfere with inter node communications i Demonstrate Infrared Communications The Infrared Communications demonstration could be done in the context of presenting the system to a potential client or to test the range of communication within a specific office environment e g with a particular floor material ceiling height and or luminaire spacing A simple demonstration of Organic Response communications can be conducted as follows switch on both Demo Nodes and place them apart from each other on the desk or table STEP2 Point your Organic Response smartphone remote with infrared dongle attachment at the target Demo Node and select Test Transmission This will cause the target Demo Node to send out a series of 30 IR signals 2 per second over 15 seconds which should be picked up by any neighbouring active Sensor Node be it a Demo Node or Organic
7. response Demo Node User Guide Revision v1 0 April 2014 1 WHAT IS A DEMO NODE srsticesaccracaconnecetanidsasanta siasasnanasidanesuentatedennyeaatemunnuaisa detonate elon aenantssdeeicamnideunintatehapiaauniaeaes 1 q BOCKI OMe LED CONE enrii ei E N e E 2 OME LE O10 E A A A A E N A E E A E TE TE T 2 C Underside panel Magnetic Contacts for Surface MOUNTING vc EEE EE eH eer rrrnn aet 2 d ordon Ee T E E E a E A T ee 2 e RAE O ea e E A E A A e A a A EEEE E E E E E A 2 f Mini USB Power Inlet Connector amp Battery Charging Status LEDS ssssssesssirrntsrrrntssrrtttsrrrttsrrrnntsrrrntrrrrrrsrrre 2 g TED ANAS A I ae E E E E E E E E bia ctios meadaenesnanmiauennniote 2 h E E a E E E E E E E EE N E E AE E 2 2 USING THE DEMO NODE ccecce a sien opts nd TEETE aE EENE AE Ea E ra ETE OE aun aceaceens 3 a AMODO NOO maiean E E E E EE ee ee ee 3 b MANDE DETO NOOS oE hanes hervina etna ba OE E esan canada iehju hired na AONE 3 Demonstrate nirarsd CommuMCaANONS cwiicsoncedansanececopornetansontsenieunnatebottuesereiyleunssnieniied somleiiaanieuaesan dadantatans 3 ii WAOE TTOTTE S aaa E E A E i 4 lil Demonstrate a Relay of Optimised SettiNgS eesssssessrrnntsrrrntssrrt tt rr1t n rr1n tSr 1n PrrEEEESrEEEESEEEEESSEEEEESEEEEESSEEEEES EENI 4 Please note that interaction with the Demo Node is performed using the Organic Response Smart Phone App which has been downloaded onto an iPhone iPad iPod Touch fitted with an infrared dongle
8. the Demo Nodes can be attached to two adjacent luminaires or alternatively the nearby t bar ceiling using the magnetic contacts on the back of the Demo Node casing O STEPI Repeat the transmission test and count the number of successful communications between the two nodes This can be completed in any location to show both where communication will occur as well as where it won t Note that receipt of 27 or more of the 30 Infrared test signals is indicative of strong and consistent communication Demonstrate a Relay of Optimised Settings The IR communications can be used to relay the optimised set points of one OR Enabled luminaire to all others within communication range This increases the soeed and ease of optimising a site once installation of the luminaires is completed Start by either placing the Demo Nodes apart on a desk table or attach them to neighbouring luminaires on the ceiling DIMMING amp For added effect take your hand and place it over the transmitting Sensor MAXLIGHT Node This physical barrier will prevent the transmission of IR communications and you will observe that the dome of the receiving node will stop flashing Remove your hand and communications should continue as normal Tonnon Using the smartphone app change the dwell time on one of the Sensor Nodes Then still pointing the remote app at the same Demo Node press Relay Max and confirm that the second Demo Node dome lights up red to acknowledge
Download Pdf Manuals
Related Search