USER'S GUIDE - Crawford Kitchens
Contents
1. fit the bush into the thermostat dial T Push the dial and bush over the splined spindle firmly ensuring that the 149 C mark lines up with the reference pointer on the thermostat case When this is done remove the dial and the bush should remain in position by means of grease All that remains now is to replace the bush locating washer and lock nut and replace the dial Removal of Thermostat Cover Pilot regulating screw is located under the control cover as well as a flame rate adjuster 1f required This is normally set at the factory however 1f it becomes necessary to remove the cover the following steps are required 1 Set dial to the OFF Position Ze Remove thermostat dial by pulling forward 3 Unscrew the two screws and remove the cover Make sure that the stop does not catch against the lower plate it is to avoid this that operation 1 is necessary On units it may be necessary to remove a button cover off the control first DIAGRAM A i O a i 1 O ta A 14 D Drainage oa i a a Gas Line Pan2. gas way to the pilot a The gas way remains locked down by means of an Interlock device It is now impossible to re ignite the burner until the push button has returned to its original position Thermostat Operation The thermostat is adjusted so that when the temperature of the frying oil reaches the thermostat dial setting the burner shuts off automatically and comes on again upon cooling of the frying oil to maintain the temperature required Note For normal operation the thermostat dial can be used for the ON or OFF of the gas supply to the burner Turn off at gas cock on appliance when appliance not required for use for long periods Pan Draining A drain valve is located at the base of the cool zone and opening and closing of the valve is by means of a handle located on the front of the units behind access door SERVICE Must only be carried out by Authorised Personnel Thermostat Re Calibration for NG LPG 1 Set temperature to 149 C 2 Remove thermostat dial from control by simply pulling forward 3 Remove lock nut and bush locating washer 4 Remove bush 5 By watching carefully the temperature rise of the oil with the thermostat turn the control off by means of gripping the splined spindle when the temperature is approximately 10 C under149 C Note This allows for a slight latent heat rise after the burner is shut off 6 Place some grease into the serrated internal edge of the bush for adhesion purposes then
3. USER S GUIDE FOR DEEP FRYER NAME OF APPLIANCE MOFRL NO MANUFACTURED BY CERTIFICATE NO SPECIFICATION SUPERTRON COMMERCIAL DEEP FRYER DF 400 DF 800 DF 1200 TU S BROS PTY LTD 77 MAIN ROAD CLAYTON SOUTH VIC 3169 AUSTRALIA 6139 General Description Heavy Duty Commercial Deep Fat Fryer manufactured in stainless steel outer panels with stainless steel pan in single double or triple units Heating of the unit is by means of duck bill burners mounted on a cast U shape manifold The burner is located beneath the fry pan The fryer has a deep cool zone and comes equipped with complete flame failure and over temperature cut out The temperature of the oil 1s thermostatically controlled The splashback incorporates the flue system from the combustion chamber The flue outlet at the top of splashback deflects the products of combustion from the rear walls The outer panels are attached to a square sub frame which is rust proofed Exterior Panels Sub Frame Fry Pan Rear Panel Insulation Heating of Unit Number of Duck Bill Burners Primary Aeration Fixed Burner Supports Vessel Clearance Fluing Overall Dimensions Height over splashback Width Depth front to back Working Height Leg Height Gas Inlet Gas Regulator Thermostat Hi Limit Over Temperature Cut Out Oil Drain Valve Depth of Cool Well Width of Cool Well Operating Oil Level from Top of Pan Thermostat Capillary Location Hi Limit Cap
4. illary Location 304 N4x 1 2mm stainless steel 20x20x 1 2 square tube 2 0mm stainless steel 1 2mm aluminised steel Fibre Millboard incapsulated within a metal casing Is by means of individual duck bill burners The burners are mounted onto a cast U form manifold 40mmx40mmx3mm Square section Overall length 405mmx 160mm centres Duck Bill 45mm centres 16 x 1 05mm orifice N G 16 x 0 65mm orifice LPG 6mmx8mm up from should of thread Provided by 25mmx23mm angle iron welded to main frame Highest sloping point of pan from top of cast manifold 300mm 2x70x70 holes from combustion chamber into a rectangular vertical rising flue 50mmx300mm 1130mm 400mm DF 400 800mm DF 800 1200mm DF 1200 790mm 900mm 150mm A 34 B S P connection is provided for each pan 276mm above floor x 90mm from left hand side Within Nova 820 M V Combination Control S I T Nova 820 M V thermostatically operated combination control Approval No 4032 In circuit with Robert Shaw LCCM operation switch Thermostat E G O Model 55 130 42 Range 230 205 Approval No 4270 Robert Shaw Model LCCM 5525 028 Approval No 2263 1 B S P 25mm 270mm 92mm 80mm Bulb 210mm from top of pan ledge x 50mm centres Bulb 210mm from top of pan ledge x 50mm centres Burner Location Fry Pan Dimensions Front to Back Depth Width Nominal Hourly Gas Consumption Test Point Pressure Flue size Splashback Burner Ignition By 400mm abo
5. l the appliance to AG601 1995 Section 5 12 4 and in accordance to local regulations attention must be give to Section 5 12 4 4 and 5 12 4 5 5 12 4 6 Commercial catering equipment on combustible surface where equipment is installed on a combustible surface it shall be protected by fire resistant material Fire resistant material specifications where appliances are to be installed in non combustible area the installer must refer to AG601 and ensure the following side walls and bare walls have materials to the specifications referring to standards A S 1530 1 to be deemed not combustible and A S 1530 3 have a zero 0 index for all of the following 1 Ignitability 2 Spread of flame j Heat evolved 4 Smoke developed N B The thermal resistance not less than 0 05 M2 c w but in no instance shall the material be of a thickness less than 6mm All models have a 20mm 3 4 BSP socket gas point or compression inlet The appliance must be installed as set out in the specifications 1 e Natural gas operating test point pressure 1 KPa Before leaving installation check all gas and water fittings for leaks and instruct operator in lighting and use of appliance N B This appliance must always be mounted on 320mm legs as supplied If unit fails to operate please contact local distributor or call manufacturer on Phone 613 9543 9577 Fax 613 9544 1487 OPERATING AND MAINTENANCE INSTRUCTIONS SERVICE Deep fryer pan features a centre cool z
6. one and crumb trap A drain off valve is provided Heating of the fryer is by means of duck bill burners of high quality material with ports drawing in secondary air through the centre The unit incorporates complete flame failure safety and temperature control by a thermostat operation A manual reset over temperature device is provided mounted on the frame adjacent to the burner that should the thermostat fail the gas is automatically turned off to the pilot system Lighting Procedure for NG amp LPG Units 1 Interior of pan to contain enough oil to cover the thermostat bulb to prevent overheating on burner ignition 2 Turn thermostat to the OFF position 3 Open main gas cock 4 Press the top push button in marked with a red flame embossing and light pilot head adjacent to the burner Note On new installations this procedure may need to be repeated 2 or 3 times to allow dispersing of air trapped in gas line to unit Normal time approx 15 seconds 5 Release press button and turn thermostat dial to the maximum position for fast heat up and then back to the temperature required 6 The main burner can now be turned either completely on or off by means of the thermostat knob Note Pilot burner will not be affected rA If piezo lighting is not working manual lighting can be used Turning OFF Procedure 1 Press push button in lower button marked in white this closes the gas way to the burner and also closes off the
7. ve floor 534mm 510mm 405mm DF 400 805mm DF 800 1205mm DF 1200 NG LPG 90MJ per Pan 85MJ per Pan NG LPG 1 KPa 2 75 KPa From combustion chamber vertical riser into splashback outlet 420mm x50mm 250mm H x 90mm W Hi Tension Spark Igniter incorporated within the thermostat Pilot light mounted adjacent to the left front duck bill burner with a fast cut out thermocouple in conjunction with the flame failure control Is by means of a 1 2mm aluminized heat shield mounted off the base angle iron frame 100mm high x 400mm wide x 460mm front to back Located against flue end of appliance Floor Protection INSTALLATION INSTRUCTIONS By Authotised Personnel Only Gas point entry is 276mm above floor and located at the left side of the unit A 20mm 3 4 BSP regulator is supplied with each pan The installer is to supply and fit an isolating gas cock to the appliance for ease of servicing the control system N B Double and Triple units have separate inlet to each control and must have a separate gas cock The installer must install the appliance to AG601 1995 Sections 5 12 4 5 and in accordance with local gas and water regulations Clearances form combustible walls sides left and right 50mm Rear wall 50mm and must be installed on a fire proof base Unit may be installed against fire proof walls Refer installer instructions for special instructions for this type of installation ADDENDA The installer must instal
Download Pdf Manuals
Related Search