Gefen GTV-ETH-2COAX User's Manual
Contents
1. Gefen Ethernet Over Coax GTV ETH 2 COAX User Manual www gefentv com 1080P Hom Dh HD eye gt HIGH DEFINITION MULTIMEDIA INTERFACE lt Blu ray Osc ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen Inc c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentv com support gefentv com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice GefenTV Ethernet Over Coax is a trademark of Gefen Inc 2008 Gefen Inc All Rights Reserved All trademarks are the property of their respective companies A QW N O N O A 17 19 24 27 28 29 CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions GefenTV Ethernet Over Coax Software Installation Connecting The GefenTV Ethernet Over Coax Automatic Security Setup Feature Advanced Configuration Web Configuration Firmware Update Procedure Specifications Warranty INTRODUCTION Congratulations on your purchase of the GefenTV Ethernet Over Coax Your complete satisfaction is very important to us Gefen TV Gefen TV is a unique product line catering to the growing needs for innovative home theater solutions2. s will become active and should emit a solid blue color LINK LED The Link LED should be flashing red on initial boot up Once a link between the sending and receiving units has been established it will emit a solid blue color on both units IMPORTANT The Link LED must be emitting a sold blue color before configuration can continue If this LED continues to flash red on both the sending and receiving units it is possible that they are not physically connected within the current coaxial cable system Please confirm that both the sending and receiving units are attached to the same coaxial cable system 11 CONFIGURING THE GEFENTV ETHERNET OVER COAX Once both the sending and receiving units are linked and powered basic configuration can proceed This section of the manual refers to the sending unit as the LOCAL NODE and the receiving unit as the REMOTE NODE NOTE The following steps are for manual configuration of the nodes for a basic secure network These steps are optional as the nodes will function with their default settings However for security and performance purposes it is recommended that the following steps be performed Automatic configuration is also possible using the Automatic Security Configuration feature on page 17 in lieu of the procedure outlined in this section 1 Ensure that both the local and remote nodes are powered and are properly linked 2 Confirm that the computer with the installed GefenTV Etherne
3. Ad changes m n k conbigurshon al have effec new syshem reboot Netrok Configuration IP Ceeien gaben Freed IP Configuration IP Acker 1521682175 m Subrat Mach MODE _STATE 13 hj 255 255 255 l ABE F STATE Enabled Delai Gamma IP Adder 79271682 1 _STATEs AGC_Ts_STATE Dirabled TAG_STATE 2 Rehesh IP Configuration For access to the node s web configuration tool an IP address must be assigned Options are Fixed Manually assigned IP address DHCP IP assigned by the networks DHCP server Fixed IP Configuration Assign an IP address subnet mask and default gateway for web tool access Click on the Update button to apply settings made in this tab 20 ADVANCED CONFIGURATION MULTICAST PLE Hode advanced configuration LR en A Gerergd Hebwork Mac Phy Mil wil Secunty Vian Dep QoS Advanced Mac at Conhigquation IGMP Multicast MAC AD IP_CONFIG_OPTIONS DHCP Faced IP CONFIG Fred IP ADDR 192 165 2179 NETMASK 25E 255 255 0 BATEWATa 0 0 0 IP CONFIG NVRAM Fhad PADDR NVRAN e182 168 2173 NVRAM a 255 255 255 0 TESTAT PLC_COMNECTION_PORT PLUC_OOMNECTION Dt ADDR 0N 20E9C7 PLC CONNECTION PHY TI PUT 156 Mbp PLC_COMNECTION PHY RX PUT 156 Mb lt A j dn T Ina b ea P IGMP Multicast This option will enable or disable the node s ability to transmit IGMP multicast data SECURITY PLE hode advanced configuration renee
4. Gefen tv DIOP 9010 Web Configuration MAC Conligeratios l Home AN Cogfeg ce rezin Tepe vNersork denier mert E es Beton bo mees page This page will allow the user to adjust all options that are available just as in the ADVANCED CONFIGURATION PANEL in the GEFENTV CONFIG TOOL 25 WEB CONFIGURATION The configuration options are as follows MAC Configuration Network Configuration Multicast Configuration VLAN Configuration Priority Configuration QOS Security Configuration Hardware Reset Flash Upgrade Please refer to the ADVANCED CONFIGURATION section starting on page 19 for information on the above categories Going back to the main page can be done by clicking on any of the Return to main page links FURTHER INFORMATION ALAC State MAC zukli taa MAC Tepe Mode Type Zeetwmk kirm n Ererrptos Ke 45CM Prue 1o erun page This page will display all of the information and status of the current node The following sections are listed System Information MAC Status Network Status PHY Status Multicast Status VLAN Status Priority Status Security Status Information on this page is not configurable If you wish to make adjustments to any of these categories return to the main menu by clicking on any of the Return to main page links on the page Then click on the Change configuration link which is also available on the main page 26 FIRMWARE UPDATE PROCEDURE The firmware for the GefenT
5. 2 Click on the upgrade firmware button NOTE This procedure is the same using the web utility The web update section is located in the change configuration settings which is accessible from the main page 27 SPECIFICATIONS Standard SUPPO E UPA DHS 200 Mbps PLC Interface One Power Line port One coaxial port 4 Ethernet 10 100M Ports SECU se eege 3DES 168 bits encryption Red AC 100 240V 50 60Hz 0 15A Power Consumption eez 8W 230V Max amp 7W 110V Max Operating Temp uE kk kk K k k 0 40 C 32 104 F Operating Humidity a zE 10 90 non condensing Storage TEMP RANGE i u kk kk 20 70 C 4 158 F Storage e le EE 5 95 non condensing reya l SAW e SR e Sea level to 40 000 feet Bet Te e EE FCC Part 15 Part B Class B CE Class B 28
6. CR Gereral Hetweck Mac Pir Muss Secumly Vian Des QoS Advanced Secudy Configquratoon Coden give Paroni Code Parsvabedi Encryption Een Conima Ernie ten Hebmerk ld ADC AS STATE Enabied ESTATE AGC STATE iirabled E STATESDONE DEOHE STATE CONNECTION PORT F PLC CONNECTION L MAC ADDR T1 ane 97 PLE CONNECTION PHY T PUT 155 Mb EE ES ei ap SI HEV TADA j The security tab will allow the user to adjust the configuration password the encryption password the network ID and the alias for the node For a detailed description of each of these options please see page 14 21 ADVANCED CONFIGURATION PLC Mode advanced confiquration Generel Nebewtk Mac Pi Multicast Secuily Wlan D DoS Advanced VLAN Configuation AVRAM ADDR HVAAM 192 168 2173 TMASE_MVFUAM 255 255 255 0 GATEWAY NVRAM efi D DD TATE Done TATE JABCT gt _STATE isabled THE STATE 2 E STATE D HE AUTOCONF_STATE This option will enable or disable the node s ability to accept VLAN data If this feature is enabled on one of the nodes it must be set on all other for VLAN tag packets to pass QOS PLC Node advanced confiquration General Network Mac Phy Multicast Secur b Wien G05 QoS Advanced Quality of Service NON MAL AD Fett AER PLC_CONNECTION_PHY_T _MPUT 156 V JELE _C NMECTI N PHY JEK PUT e156 Mbi n 3 QOS quality of service is supported for man
7. THE GEFENTV ETHERNET OVER COAX 9 Once the update is complete a message will appear to indicate the update was successful Click on the ok button to continue Gefen Config Tool a Updated successfully 10 Once the update to the remote node is complete you will be presented with a window that will give the option to either return to the main configuration window or continue with advanced configuration Gefen TV assistant Gefen TV configuration assistant Gefen TY Config Tool v2 7 228 j PLC node configuration completed successfully A PLC node is now ready to use Please press Next to keep contiqurating nodes Press Advanced for advanced operations For basic usage it will not be necessary to continue to the advanced configuration For advanced options please see the ADVANCED CONFIGURATION section on page 19 To continue with the basic configuration click on the next button 15 CONFIGURING THE GEFENTV ETHERNET OVER COAX 11 Once the configuration for the remote node is complete the local node will then have to be configured Click on the local node which is labeled as the ETH connected node and press next to continue Gefen TV configuration assistant Gefen TV configuration assistant be cure here nodes arg connected and press Update List Once all nodes are in ihe let select the node bo configure and prets Theri button Gefen A The assistant detected faking
8. V Ethernet Over Coax can be updated by FTP TFTP or a direct file The firmware update can be executed from either the ADVANCED CONFIGURATION PANEL or the WEB UTILITY UPDATE VIA THE ADVANGED CONFIGURATION PANEL Firmware updates can be accomplished from the General tab in the ADVANCED CONFIGURATION PANEL See page 19 for instructions on how to enter the ADVANCED CONFIGURATION PANEL BLE Hodo alvan d cond lquraliocn Si oe BC A Genia Mehwerk Mac Phe Mu ean Securty Vien Ged Qof Gage Hardware Hesek Facio Here Hardveare Fi nasi Fi rawann Lan Lipide Pastel Ser IP Seddon P Use el ett mme cl Pr gun Ea ESTA GC EE EKTA STATE Fix ss TR IFE EXTE_STATE PUC_CORMECTION PQA Tz C_CCHMNE CTIOH HAC ADGA Mest Gr CORMECTIDH_ PHY TH APUT e196 Hig PLE CONE CT ION Div eu HBM wl H Upgrade Via FTP or TFTP 1 Select the update protocol Either FTP or TFTP 2 Enter the server IP address 3 Enter the user name and password 4 Enter the name of the file if the file is not in the root directory of the TFTP or FTP directory you have to write the whole route from root server directory 5 Select which section you would like to update Firmware Loader or Factory Settings 6 Click on the firmware update button Upgrade Via File 1 Use the browse button to the right of the firmware file window and select the firmware update file You can also manually type the full path to the firmware file
9. We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line and hope you find your solutions Don t see what you are looking for here Please call us so we can better assist you with your particular needs The Gefen Ethernet Over Coax The Gefen TV Ethernet Over Coaxial Sender and Receiver units send RJ 45 Ethernet over RG 59 or RG 6 Coax cable at a distance of up to 300m 1000 feet Ideal for legacy installations where Coaxial cable is already permanently in place these devices breathe new life into remote network extensions where re wiring is not possible How It Works Connect your existing Ethernet network cables to the Ethernet Over Coaxial Sender unit then plug in your Coaxial cable to the Coaxial jack on the Sender unit At the other end of your Coaxial cable run attach the Ethernet Over Coax Receiver unit and your network cables Power cycle your equipment You will now receive Ethernet network signals at the end of your cable run as if you had cabled the run with Ethernet cables OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENTV ETHERNET OVER COAX This device passes all 10 100BASE T Ethernet network protocols TCP IP NETBUEI Microsoft Networking etc at soeeds of up to 200Mbps Full duplex fast Ethernet All devices connected to th
10. aging traffic between nodes The supported protocols are TCP port priority UDP port priority 802 1p TOS RFC 1122 DSCP RFC 2475 No Priority L eS eg 22 ADVANCED CONFIGURATION ADAVANCED QOS PLE Bode advanced configuration rere AJ Geer Network Mac Phe Muscat Secunly Vien QoS Dei Advanced Quakly of Serice VER sir d1 0p 910 2 ere Rule 1 MAC ADDA 00 20E MAC ADOR MESSAGE iet Vali Peace upe IP_COMFIG_OPTIONS DHCP Fined DOMFIG F SyNC_STATE MODE STATE 13 C PY STATE E natied CR QOS quality of service prioritization Rule 1 will be applied to all packets first and then Rule 2 Prioritization protocols are UDP is high priority TCP is low priority TCP is high priority UDP is low priority UDP port XXXxX is high priority the rest is low priority UDP port XXXxX is low priority the rest is high priority TCP port XXXX is high priority the rest is low priority TCP port XXXX is low priority the rest is high priority Use 802 1p prioritization No prioritization N X L ey 23 WEB CONFIGURATION If an IP address has been set in the ADVANCE CONFIGURATION PANEL access to the WEB UTILITY will be enabled To access the WEB UTILITY open your web browser and type the ip address into the address field The IP address is dependant on the IP Configuration Setting assigned on page 20 The IP address can either be assigned by the DHCP server or a static IP address can
11. ate once the included power supply is properly connected 7 GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATION How to Connect the GefenTV Ethernet Over Coax Installation of the GefenTV Configuration Assistant 1 Insert the included installation CD ROM into your computer that will be used to configure the GefenTV Ethernet Over Coax 2 The auto run will begin the installation process If auto run does not start or auto run has been disabled please navigate to X drive where X is the drive letter or your CD ROM drive and run the autorun exe file 3 Click on the Install Utility option CD Autorun FQ d1nstall Utility gt CJ Quick Installation Guide OR Browse CD User Manual Guide 4 Choose your preferred language and click on the OK button to continue Currently English is the only selectable language Installer Language GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATION 5 Close all other applications and press the Next button to continue D Gefen TY Ethernet over Coax Setup Welcome to the Gefen TV Ethernet over Coax Setup Wizard This wizard will guide you through the installation of Gefen TY Ethernet over Coax It is recommended that you close all other applications before starting Setup This will make it possible to update relevant system files without having to reboot your computer ATTENTION To install the software you must have administrator user privileges If you do not ha
12. ation Mode ASCM can be activated on each node Follow the below steps to automatically setup a secure connection between multiple nodes lt is important to understand these concepts before proceeding with the Automatic Security Configuration Master Node Fixed Access Point The Master node is the unit that all of the Slave nodes use to copy the Net ID and Encryption Key from Because all of the nodes on a network need to have the same Net ID and encryption key to operate properly together there needs to be a single Master node that stores the information that all other Slave nodes will use to properly configure themselves A Master node is indicated by its Power LED glowing a solid RED color It is recommended to have only one Master node on the coaxial network Slave Node Normal A node in this mode will be indicated by its Power LED glowing a solid Blue color Multiple Slave nodes can be on the same coaxial network Automatic Security Configuration Mode ASCM This mode is initialized by pressing and holding the Security Reset button on the front panel for approximately 2 seconds Once the node s Power LED begins flashing RED release the button This mode lasts for approximately 30 seconds and will return to normal operation after this time period Both the Master and Slave nodes must be in ASCM for the automatic procedure to complete successfully When a Slave node initializes ASCM it will first attempt to find a Master n
13. be manually assigned AUTHENTICATION The browser should open the authentication page displayed below Wait So Gi Coalungbie Aaitabar kir fotisalh Iris bi CO e E hAm H Ge se x Wak Configuration Aarie G efe n tv DY Wid Web Configuration Authentication To enter the WEB UTILITY enter the configuration password The default password is paterna unless modified during the setup stage on page 14 Factory Reset The unit can be reset to factory settings from this menu Enter the factory reset password The default password is betera 24 WEB CONFIGURATION MAIN PAGE FER XNIR ZUR TT Mode an n Ar et Li M SAL GA E CO BK ten OI 8 Tr Sr r er diken bl aki ll denk a ae Gefen tv DWLOP 9040 Web Comfigaration Leo Hall ranan lana PLC Comacina M Fe Ti FLE Fem Alil Airai Thinh EDET XE bp ure nal hafir Ware r ma INTA Cee Sei kesra lafermotes MAC Tepe MAC Adee DD Acero ETNE AGC EX ADC Tu Aiii iacl Heist iiam as onary The main page will display general configuration information Clicking on the further information link will navigate to a new page with all the current configuration information See page 26 Clicking on the change configuration link will navigate to a new page where all configuration options will be available for adjustment see below WEB CONFIGURATION ei E baus Ipnnzlmkoe u be HO j TAK he Ogu eee D r iyana
14. e see page 17 Pressing this button for more than 10 seconds will perform a factory reset AC Power Cable Input Input for the supplied AC power cable Coaxial Output Coaxial output to link the sending and receiving units together This connector will support RG 6 and RG 59 cables LAN 1 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 1 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 2 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 2 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 3 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 3 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 4 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 4 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port Link LED This LED will activate once a link has been established between the sending and receiving units It will blink when activity is detected to signify that data is actively being trafficked to and from the sender Power LED This LED will activ
15. e sending and receiving nodes must be on the same subnet with unique IP addresses to communicate properly Multiple receiving nodes can be used on the same coaxial cable system to extend the network to multiple locations FEATURES Features e Supports up to 200 Mbps data transmission rate e Extension of up to 1000 feet 300 meters e Web configuration for easy maintenance e Features include IGMP multicast VLAN and QOS packet management e 3DES 168 bits encryption used for secure operation e Four RJ 45 Ethernet ports Package Includes 1 GefenTV Ethernet Over Coax sender 1 GefenTV Ethernet Over Coax receiver 1 3 foot Ethernet Patch Cable 2 Power Adapter Cables SENDER PANEL LAYOUT Front Panel Standby Reset Back Panel Top Panel LAN LINK ewe Gefen Ethernet over Coax S SENDER PANEL DESCRIPTIONS Standby Button Pressing this will put the sending unit in standby mode The unit will not transfer any information to the receiving unit in this mode To release standby mode simply press the button again Ethernet Input Port Connects to the Ethernet source i e a router computer or Internet connection via a standard network cable Security Reset Button Pressing this button for 2 seconds will activate the Automatic Security Configuration please see page 17 Pressing this button for more than 10 seconds will perform a factory reset AC Power Cable Input Input for
16. k Mas Pry Muficast Secumty Vian Det Daf Advanced MODELSDWw oF sod Ha dwara Herel Factory Hezet HETE e en WER delle S002 A SD een h Firmwaanre Update MAC ADDR MESSAGE Nek Vaid Plame upe IF C N DPTIONS DHCP Food Upgrade Pretocol hee Server IP Adder FTP Uer FTP Paw vaced File Hama Update Section GE SCT leese CR Se ac Bi Is Upgrade Firmwana dU T C HE STATE u HUKL BOTS Eapwesne File EXTA TYPE m10 Mbps _ POAT f PLC CCONNECTION MAC ADDA U 2E9C7 FPUC_COHMECTION_PHY_ TS _APUT 156 Mb DL CONNECTION _PHY Fos APU TeS Mia Hardware Reset This will reboot the node Settings made in this menu will be applied once the node is restarted Factory Reset This will return the node to factory default settings A password is required to complete this operation The default password is betera This has the same effect as pressing and holding the Securty Reset button on the front panel for approximately 10 seconds 19 ADVANCED CONFIGURATION Firmware Update This section is used to update the node s firmware from a server location Please see the Firmware Update section on page 27 for full details Upgrade Firmware This section is used to update the node s firmware from a file Please see the Firmware Update section on page 27 for full details NETWORK PLE Node advanced configuration INFO UL AER FITS General Network Mac Pe Mubicast Secur j Vian QoS QoS Advanced
17. llation La lt Back instal DI _ Cancel 8 The program files will copy to the specified location in the previous step When the process is complete you will see the window below Click on the finish button to complete the software installation process Gefen TV Ethernet over Coax Setup Completing the Gefen TV Ethernet over Coax Setup Wizard Gefen TV Ethernet over Coax has been installed on your computer Click Finish to close this wizard 10 CONNECTING THE GEFENTV ETHERNET OVER COAX 1 Connect the source i e computer router switch to the GefenTV Ethernet Over Coax sender unit using the supplied CAT 5e cable 2 Connect the GefenTV Ethernet Over Coax sender unit to a coaxial RG 59 or RG 6 cable system Please ensure that the connected coaxial cable system has an available endpoint either directly or through a coaxial cable splitter 3 Connect the GefenTV Ethernet Over Coax receiver unit to the coaxial cable system 4 Connect the Ethernet devices i e computer game system set top box to the GefenTV Ethernet Over Coax receiver unit Up to four devices are supported 5 Connect the included power cables to both the GefenTV Ethernet Over Coax sending and receiving units POWER LED Once the power cable is connected the Power LED should become active with a solid blue color LAN LED When a valid Ethernet connection is detected on the sending and receiving Ethernet jacks their corresponding LED
18. modes in ihe electric nelwark H you Bink more modes should ba shit Hi you do not remember the pagsend of the node You wil have fo reset the node wih iactory values pressing Factory Reset Alias AP Quality IN AX AP 159 161 Update List 12 Using the same Net ID and encryption key from the remote node input the same information into the corresponding fields for the local node The Alias field should be set to a different name as the remote node for easy identification Gefen TY configuration assistant Gefen TV configuration assistant This is the current configuration of the PLC node If you want to modify Gefen tv YD some parameter do it and press Next button PLE Node configuration Curent firmware spirt_dwi0p 9010s 4 6 G cvs Net ID Encryption key Alias Kind of node New password Confirm password L ve D Once the information has been input click on the next button to continue A confirmation window will appear once the update is complete The same window in step 10 will appear with the option to continue with the advanced configuration lt is not necessary to continue with the advanced configuration for basic operation Click on the next button to return to the main configuration window and exit the configuration tool by clicking on the exit button 16 AUTOMATIC SECURITY CONFIGURATION FEATURE To quickly setup the Gefen TV Ethernet Over Coaxial for secure use the Automatic Security Configur
19. ode in ASCM If a Master node in ASCM is not found it will assume the role of the Master node To avoid accidentally setting a Slave node as a Master node make sure that the Master node is in ASCM when activating a Slave s ASCM Any Slave node that assumes the role of a Master node will automatically have a random ASCII Net ID and Encryption Key generated Connect the computer with the installed Gefen TV Config Tool software to the node that you wish to initially set as the Master node If a node is connected to media server or router it is recommended that this node be set as the Master node for increased performance Please refer to the next page for step by step instructions on how to activate the Automatic Security Configuration feature for the Gefen TV Ethernet Over Coax nodes 17 AUTOMATIC SECURITY CONFIGURATION 1 Connect the computer with the installed Gefen TV software to the node you wish to set as the Master node 2 Press and hold the Security Reset button on the node ASCM located on the front panel for approximately 2 seconds The Power LED should begin to flash RED then release the button 3 After approximately 30 seconds the Power LED should stop flashing and glow solid RED This indicates that it is now a Master node If this node was a Slave node normal node before this process it will now have a randomly generated ASCII Net ID and Encryption Key set 4 Open the Gefen TV Config Tool page 12 There
20. ration assistant This is the current configuration of the PLC node If you want to modify some parameter do it and press Next button PLC Node configuration Current firmware spirt_dwi0p_ 9010s 4 6 G_cvs Net ID Encryption key Alias Kind of node New password Confiim password The PLC node configuration screen is separated into the following items NET ID This is the name of the network This name must be the same for both the local and remote nodes for proper operation The NET ID can be an ASCII string up to 20 characters long ENCRYPTION KEY This is the password needed for network authentication by all nodes If you wish to set an encryption key please set the NET ID first The password can be an ASCII string up to 24 characters long ALIAS This name is for easy identification of the node This can be an ASCII string of up to 10 characters long This field is optional NEW PASSWORD CONFIGURATION PASSWORD This is to set the configuration password lf a new password is set here the configuration tool will ask for it every time you access the node The default password is paterna This field is optional CONFIRM PASSWORD The password entered into the new password listing above must also be entered here This is for confirmation purposes Enter the Net ID encryption key and alias into the corresponding fields Once these fields are completed click on the next button to continue 14 CONFIGURING
21. should be a random ASCII value as the Net ID If you wish to use this Net ID for the other Slave nodes proceed to step 5 Otherwise you can now set your own Net ID and encryption password which will be applied to all of the Slave nodes in the next step To do this click on the local ETH connected node MAC address and press the next button Change only the Net ID and encryption password fields and click on the next button Once the local node has been updated proceed to step 5 5 For this step to complete successfully both the Master and Slave nodes have to be in ASCM To do this press and hold the Security Reset button on the Master node for approximately 2 seconds The Power LED should begin flashing RED Within 30 seconds press and hold the Security Reset button on the Slave node s for 2 seconds to enter ASCM The Slave node s Power LED should also begin to flash while it receives the Net ID and Encryption Key information from the Master node Once the Power LED on both the Master and Slave nodes stop flashing and glow solid the setup will be complete Check this by opening the Gefen TV Config Tool and seeing that all nodes have the same Net ID NOTE If the Slave nodes are located at a great distance from the Master node it is recommended that Step 5 be repeated for each Slave node separately The window that each device remains in ASCM is only 30 seconds and it may not be possible to put all Slave nodes in the ASCM within the
22. t Over Coax software is connected to the local node 3 Start the Gefen TV Config Tool from this location Start Menu All Programs GefenTV Ethernet Over Coax Gefen TV Config Tool 4 The introduction screen should appear as the image below Click on the next button to continue Gefen TY configuration assistant Welcome to the assistant for the Gefen TV configuration This assistant will help you to configure your Gefen PLC node Once the assistant is finished the Gefen PLC node will be fully ready for its use Before you start the assistant be sure that the Geten PLC Nodes are correctly connected to the electric network Besides be sure you have the ETH wire connecting correctly the modem with the computer v2 7 228 5 G Searching nodes O 12 CONFIGURING THE GEFENTV ETHERNET OVER COAX 6 Once all possible nodes have been detected the program will display all of these nodes as in the window below Gefen TV configuration assistant Gefen TV configuration assistant Gefen CG The assistant detected folowing nodes in the electric network N you think more nodes should be shawn a b sure hese nodes ore connected and press Update List Once al node are in ihe i select the mode b configure and press Theri button li you do nol remember the password of the node you wil have to rese the node wih factory values pressing Factory Reset MAC Het ID Alias AP Quality ETH conected mode gau z
23. the supplied AC power cable Coaxial Output Coaxial output to link the sending and receiving units together This connector will support RG 6 and RG 59 cables LAN LED This LED will activate when a connection to a valid Ethernet source is established It will blink when activity is detected to signify that data is actively being trafficked to and from the receiver Link LED This LED will activate once a link has been established between the sending and receiving units It will blink when activity is detected to signify that data is actively being trafficked Power LED This LED will activate once the included power supply is properly connected RECEIVER PANEL LAYOUT Front Panel eege Standby 4 3 2 4 Aeset 1 2 3 Back Panel AC In Coax Out 4 5 Top Panel LAN LANDE LANJ LANA LINK PWA Gefen O ON O 10 11 Ethernet over Coax R e gt 10 11 RECEIVER PANEL DESCRIPTIONS Standby Button Pressing this will put the receiving unit in standby mode The unit will not transfer any information to the sending unit in this mode To release standby mode simply press the button again Ethernet Input Port 1 through 4 Connects to an Ethernet device i e a computer or gaming system via a standard network cable 4 ports are available for 4 separate devices Security Reset Button Pressing this button for 2 seconds will activate the Automatic Security Configuration pleas
24. time frame It is also possible to temporarily relocate the Slave nodes to a coaxial port closer to the Master node for this configuration process and then move them to their permanent location after this process is complete If a Slave node is accidentally set as a Master node you can hard reset the node by pressing and holding the Security Reset button for approximately 10 seconds This will revert the node to a Slave node and reset all internal configurations to factory settings 18 ADVANCED CONFIGURATION There are optional advanced settings that can be configured for each node The advanced menu can be accessed directly through the main configuration page Click on the MAC address of the node you wish to configure and click on the advanced button to the left of the node listing Gelen TV configuration assistant Gefen TV configuration assistant Gefen The assistant defected folowing nodes inthe electric network R you think mone nodes should be shown be cure these nodes ar connected and press Update List Once all nodes are inthe izt ele the node fo configure and press Mel button H you do nol remember the pik a wW rnd of the node you wil have io rese the rode wih faciory valies pressing Factory Reset Alias AP Quality ETH connected TH Ri PLC connected nodes goa Coax Recai AP 15G 155 Advanced gt g Facto Aerei GENERAL PLC Mode advanced configuration pital ed terre General Maiwc
25. un sr 1008 TA Rx PLC connected nodes o0120E9C7008 AP 159 161 The local node that the computer is connected to will appear as the ETH connected node All remote nodes will be listed as PLC connected nodes NOTE Both the local and remote nodes must use the same Net ID and encryption passwords for proper operation These will be configured in the next step However it is important to configure the remote nodes first If the local node is configured first all remote nodes will become inaccessible and will have to be removed from their locations and physically connected to the computer where they can be configured to match the local node s settings 7 To begin configuration click on the mac address of the remote node PLC connected node and then click on the next button Gefen TV configuration assistam Gefen TV configuration assistant Gefen i i The asian detected fofirsang nodas in ihe electric network H you think more modes shouid be ahen a be qure here nodes are connected and press Update List Once all nodes ane in ihe ki select the node bo configure and press Theri button Hi you do nod remember the pasword of the node you wi have to reset He node with Tactory Vales pressing Factory Reset MAC Het ID Alas AP Quality ETH connected nod gn 12 0EsE1809 TN RX PLC connected mod AP 159 161 13 CONFIGURING THE GEFENTV ETHERNET OVER COAX Gefen TY configuration assistant Gefen TV configu
26. ve such privileges please contact your systems administrator Click Next to continue Dears 6 Please read the license agreement and click on the Agree button to continue Gefen TV Ethernet over Coax Setup License Agreement Please review the license berms before installing Gefen TY Ethernet over Coax Press Page Down to see the rest of the agreement Technologies Professional Software License Agreement This WinPcap Professional Software License Agreement Agreement is made as of Effective Date by and between CACE T LLC with offices located at 1949 Sth Street Suite 103 Davis California USA CACCE or Licensor and icensee as defined hereunder IF you accept the terms of the agreement click I Agree to continue You must accept the agreement to install Gefen TV Ethernet over Coax GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATION 7 Please choose the program installation destination The default location is C Program Files Gefen TV Ethernet Over Coax To set your own destination click on the browse button and navigate to your preferred location Click the install button to continue Gefen TV Ethernet over Coax Setup Choose Install Location Choose the folder in which to install Gefen TV Ethernet over Coax Setup will install Gefen TV Ethernet over Coax in the following Folder To install in a different folder click Browse and select another folder Click Install to start the insta
Download Pdf Manuals
Related Search