Home

Operating instructions Washer-dryer WT 2780 WPM

1. HONEYCOMB CARE S5 Operating instructions Washer dryer WT 2780 WPM To avoid the risk of accidents en AU NZ or damage to the machine it is essential to read these instructions before it is installed and used for the first time M Nr 09 441 860 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure they are offered for recycling Disposal of your old appliance or machine Electrical and electronic appliances machines often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance or machine Therefore please do not dispose of your old machine or appliance with your household waste K Please dispose of it at your local community waste collection recycling centre and ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person The plug must be render
2. Deactivate the code as described in the Settings menu Power cut Open the drum door as described in the next section The door was not correctly engaged Press hard against the lock side of the drum door and then press the Door button There is still water in the drum and the machine is unable to drain Clean the drain filter and drain pump as described in the next section The door cannot be opened during or after drying For safety reasons the drum door cannot be opened if the temperature is higher than 70 C Wait until the temperature is less than 70 C Deactivate the Extended cool down time as described in the Settings menu For safety reasons the drum door cannot be opened if the suds temperature is higher than 55 C 62 Problem solving guide Opening the drum door in the event of a blocked drain outlet and or power failure m Switch the machine off There is a lever behind the detergent drawer fascia panel m Remove the lever m Use it to open the access flap Blocked drain outlet If the drain outlet is blocked up to 25 litres of water will be retained in the machine N Caution If laundry has been washed at a high temperature water draining out of the machine will still be hot Danger of scalding Procedure for draining the machine m Place a suitable container under the access flap When draining water from the machi
3. Select the required setting and then determine whether laundry should be damper or drier after drying Extended cool down The cooling down phase which takes place before the end of a programme can be lengthened if required This makes the garments easier to handle The cooling down phase can be lengthened from O min to 18 minutes m Set the duration with the V and A buttons and confirm your setting by pressing the OK button The programme duration will increase accordingly Anti crease helps prevent creasing if laundry is not normally removed immediately after the end of a programme The drum will turn at intervals for up to 30 minutes after the programme has finished The door can be opened and laundry removed at any time during the anti crease phase On Anti crease is activated default setting Off Anti crease is deactivated 83 Optional accessories Miele offers perfect care for your laundry with a wide range of special programmes designed to suit the fabrics being washed and dried Miele have also developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry The Miele CareCollection detergents and conditioning products are listed below You can order these and many other useful products via the internet at www miele shop com All the products can also be ordered from Miele See ba
4. X gt lt X X X X X Starch X Use liquid detergent When Pre wash is selected it is recommended to use a liquid detergent dispenser insert in the detergent dispenser drawer UH The insert is available from your Miele Chartered Agent or from Miele D Only use proofing agents which are stated by the manufacturer as being suitable for use on membrane textiles Do not use proofing agents which contain paraffin Add proofing agents to the fabric conditioner compartment amp Sx Use powder detergent Specialist detergent This detergent is designed specifically for the wash programme or type of fabric see the Miele CareCollection detergents and conditioning products in Optional accessories 33 WASHING All modern detergents produced for automatic front loading washing machines are suitable Use dispensing aids e g balls if these are supplied with the detergent Tablets are suitable for full loads but note that it may be impractical to reduce tablets for smaller loads Some tablets do not dissolve as rapidly as others and may not be suitable for programmes with short durations Do not use biological detergents on silk as the enzymes may damage the silk Instructions for use and recommended dosage amounts are given on the detergent packaging Liquid detergent should be dispensed using a ball provided by the manufacturer for programmes without a pre wash Fo
5. m withdraw the transit bar m withdraw the transit bar 69 Installation and connection Levelling the machine NTo avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed The machine must stand perfectly level on all four feet to ensure safe and proper operation Incorrect installation may increase electricity and water consumption and may cause the machine to move about False values may also show in the Load and Detergent display m Fit the covers on to the two holes Then plug the holes as shown with the caps The machine must not be moved without the transit fittings in place Store them in a safe place for future use They must be re fitted if the machine is to be moved again e g when moving house Re fitting the transit bars Re fitting is carried out by reversing the procedure 70 Installation and connection Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine All four feet are screwed in when the machine is delivered m Using the spanner supplied turn counter nut 2 in a clockwise direction Then turn counter nut 2 together with foot 1 to unscrew m Use a spirit level to check the machine is standing level m Hold foot 1 securely with a pipe wrench Turn counter nut 2 again using the spanner supplied until it sits firmly up against the housing AAII four counter nuts
6. C Max load 2 0 kg Suitable for Sportswear such as singlets and leggings as well as microfibre and fleece garments Notes Do not use fabric conditioner Please observe the instructions on the wash care label Extra options Short Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold Trainers cold to 40 C Max 2 pairs of shoes Suitable for Trainers do not use for leather shoes Notes Observe the manufacturer s care label Remove coarse soiling with a brush before washing Do not use fabric conditioner Apre wash without detergent is carried out automatically to remove dust Extra options Rinse hold pre wash is activated automatically Please note that the buckets represent garment care label symbols See Garment care 28 label symbols WASHING Outerwear cold to 40 C Max load 2 0 kg Suitable for Outerwear made from membrane fabrics such as Gore Tex SYMPATEX WINDSTOPPER etc Notes Zip up jackets before washing Do not use fabric conditioner Extra options Short Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold Proofing 40 C Max load 2 0 kg Suitable for Treating microfibre fabrics skiwear and table linen made from mainly synthetic fibres with a water and stain resistant finish Notes The items should be colour sorted and freshly launder
7. Cleaning and care Disconnect the machine from the electricity supply by switching off at the wall socket and withdrawing the plug before any cleaning and maintenance work A range of Miele branded cleaning and conditioning agents is available to order from Miele or via the internet on www miele shop com Cleaning the machine ADo not use solvents abrasive cleaners glass cleaners or all purpose cleaning agents These might damage plastic surfaces and other components because of the chemicals they contain N The machine must not be hosed down m Clean the casing and the control panel with a mild non abrasive cleaning agent or soap and water Wipe dry with a soft cloth m he drum can be cleaned using a suitable stainless steel cleaning agent following the instructions on the packaging Extra cleaning Carry out a hot wash 70 C or above with powder detergent approx every 6 weeks to help prevent deposits building up in the machine These can occur when washing is mainly done at low temperatures and can lead to unpleasant smells If you have no reason to wash occasionally at this high temperature then run a Cottons 95 C programme with detergent but no laundry at regular intervals Cleaning the detergent dispenser drawer The pre wash and main wash compartments of the detergent drawer are self cleaning However for hygiene reasons the entire detergent drawer should be cleaned as follows on a regu
8. and liquid detergent together in the dispenser drawer Grey greasy particles cling to washed laundry Insufficient amounts of detergent were used to break down the particles of grease in heavily soiled laundry Use more detergent Before washing the next load run a Cottons 95 C programme with powder detergent but without a load White residues which look like powder detergent are seen on dark textiles after washing The detergent contained compounds zeolites to aid water softening which are not soluble in water They have ended up on the laundry Try and brush off the residues with a soft brush once the laundry is dry Wash dark textiles using a detergent which contains no zeolites Liquid detergents usually contain no zeolites Use the Dark garments programme for dark coloured laundry 60 Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The laundry is still damp after a drying cycle The load was too small for the electronics to assess the residual moisture correctly In future dry small loads in a timed drying programme The laundry has formed a ring in the drum during the spin because it was distributed unevenly The laundry has formed a ring in the drum during the thermospin because it was too damp or the spin speed was set too high Turn the programme selector to Stop Open the door a
9. 50 Interrupting a programme se 6 ee 50 Charnging a programme 2 6 een lead Pad es Sag aged erbE RSASdor a 50 erus NC 51 Delay start ionic RR RR edd Phoebe nk Aet aba 52 Cleaning and care 0 00 0 eee 53 Cleaning the machine lllssessiessels e 53 Cleaning the filter in the water inlet llli else 55 Problem solving guide 0 0 cee 56 The programme does not start 0 ee 56 A fault message appears in the display 0 0 00 eee 57 Problems with the load size indicator liene 58 General Problems sss ees ames ape ELE RU RUE SO Red RU e ddr uas 59 An unsatisfactory wash result eee 60 An unsatisfactory drying result iiie 61 The drum door cannot be opened by pressing the Door button 62 After sales service 2 iced sd ei bx we x RERO RR Re Y cete EA ROLE ded s 65 Future updates PO oo erake srate tee a enra ns 65 Appliance warranty 0 ee E 65 Optional accessories 00 0002 tees 65 Installation and connection 0 0 0 0 e cee 66 Bone LHP 66 Rear VIEW s obs URP GOL PY Radeks P Pen PARADE Radke P ERP ESS n A e ed 67 metalation SUtfaoess ss erras phe Ea a oec sm ace ROR ERU ui ter ars 68 Contents Installing the washer dryer 2 2 0 es 68 Removing the transit fittings isse 68 Levelling the MaChinG 00 2 h204 eem etie dte ete dece dete d ces 70 Screwing out and adjusting the feet 0 0 lilii sisse 71
10. CareGollection 32e eb es tRERRPRRIMPerTOPAsSieie eee US 84 Warning and safety instructions P It is essential to read these instructions This washer dryer conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the washer dryer please read these instructions carefully before using it for the first time They contain important information on its installation safety use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application P This appliance is designed for domestic use and for use in similar environments by guests in hotel or motel rooms bed amp breakfasts and other typical living quarters This does not include common shared facilities or commercial facilities within hotels motels or bed amp breakfasts It must only be used to wash garments which have been declared suitable for washing by the manufacturer indicated on the care label dry garments which have been washed in water previously and have been declared suitable for drying by the garment manufacturer indicated on the care label Any other applications may be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation 6 Warning and safety instructions P This wa
11. Garments are dampened before the programme starts to help reduce creasing Select the Water plus extra for very absorbent fabrics Select Normal For garments that are required immediately Hand iron For garments that are to be ironed or hung out to completely dry on a coat hanger Timed drying Check the items as you are drying them to find the optimum time Important Creasing increases the larger the load and the longer the drying time Weight of dry laundry 42 DRYING Smoothing Max load 2 5 kg Suitable for Cotton and linen fabrics Minimum iron items made of mixed fibres cotton or synthetic fabrics Note Garments are dampened before the programme starts to help reduce creasing They are not completely dried in this programme to make them easier to iron Remove garments as soon as the programme finishes Select the Water plus extra for very absorbent fabrics Warm air Max load 2 5 kg Timed drying Suitable for Drying or airing individual items Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Further programmes Dark garments Max load 2 5 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Dark garments made from cotton or mixed fibres Extras Low temperature thermospin Extra quie
12. Interim Final spin level rhythm level spin Cottons ky wl 2A J J Minimum iron Lt 2 33 J J Denim 3 JV Woollens iy B C1 2 J J Express 20 2 9 J J Shirts Cy C1 2 J Automatic plus ym DAGO e 2 99 J J Dark garments ty k 3 J J Delicates p D ai B J Sportswear k k 2 J J Trainers 9 ps E E 2 J Outerwear t D tj 3 JD J Proofing Tes D v Soft toys ky 3 J J Hygiene ey 3 4 vA J First wash k pe 2 v J Silks a E 2 v Pillows ty tJ 3 vV Curtains 9 pes D ky 3 J Separate rinse Ld 2 J Starch tes v Please see next page for description of the symbols 31 WASHING k Low water level key Medium water level C1 High water level Intensive rhythm Normal rhythm Gentle rhythm Sensitive rhythm Ultra sensitive rhythm Handwash rhythm This machine has fully electronic controls with automatic load recognition It takes in the right amount of water required for the programme depending on the amount of laundry and its absorbency rate This means that programme cycles and durations can vary The programme sequences outlined in the chart are based on the basic programme with a full load Extra options which can be selected have not been taken into account The display shows the stage the programme has reached 32 Special features in the programme sequences Anti crease At the end of the programme the dru
13. Low temperature The temperature is reduced during the drying process Delicate facbrics such as acrylic with the KJ symbol on the care label are dried more gently If Low temperature is selected Thermospin will not be activated The duration of the programme will increase when Low temperature is selected The Low temperature Extra can only be used during drying Thermospin Thermospin is used in some programmes to reduce the energy consumption during the drying process Thermospin is not activated if a drying time is selected Thermospin is not activated if Low temperature is selected The maximum spin speed for Thermospin is the same as the final spin speed for the wash programme being used Extra quiet You can reduce the noise level of the washer dryer if you want to dry during rest periods e g at night The buzzer does not sound Thermospin is limited to 900 rpm m Press the Further extras button Further extras O Extra quiet Back m Confirm the selection of Extra quiet by pressing the OK button Leave the Extras sub menu by pushing the Further extras button 39 DRYING Adding or removing laundry after a programme has started m Press the Door button to open the drum door N Do not touch the metal cap inside the door glass or the back of the drum as they will be hot m Add or remove items as required m Close the drum door T
14. Pillows cold to 90 C 2 pillows 40x80 cm or 1 pillow 80x80 cm Suitable for Washable pillows with feather down or synthetic fillings Note Please observe the instructions on the wash care label Extras Water plus Stains Extra quiet Extra rinse Rinse hold Curtains cold to 40 C Max load 1 0 kg Suitable for Curtains including net curtains specified as machine washable by the manufacturer Notes For curtains which crease easily reduce the spin speed or deselect the spin Remove weights from curtains A pre wash without detergent is carried out automatically to remove dust Extras Water plus Stains Extra quiet Extra rinse Rinse hold Pre wash is activated automatically Separate rin se Max load 5 5 kg Suitable for Hand washed items which only need airing Note Reduce the spin for items which crease easily Extras Extra quiet Rinse hold Starch Max load 5 5 kg Suitable for Starching table cloths serviettes and workwear Notes The laundry should be washed but not treated with fabric conditioner Reduce the spin for items which crease easily Extras Extra quiet Rinse hold Drain Spin Max load 5 5 kg Notes Drain only Select No Make sure you select the appropriate spin speed 30 WASHING Programme sequence Main wash Rinses Spin Water Wash Water Rinses
15. after the programme has started m Use the V and buttons to alter the temperature Changing the programme sequence Changing the spin speed You can change the spin speed up until the final spin begins You can change the thermospin speed up until the thermospin begins Altering the drying level drying time You can alter the drying level or drying time during the washing programme but not once the drying programme has started Selecting or deselecting a drying programme You can select or deselect the drying function during a washing programme if this is permitted for the particular programme Changing Extra options It is possibe to select or deselect some Extra options up to 5 minutes after the washing programme has started It is not possible to make any changes if the safety lock has been activated Safety lock The safety lock prevents the machine from being opened or the programme cancelled during a washing or drying programme To activate the safety lock m Press the Start Stop button m Select Activate safety lock and confirm your selection The machine will now not accept any changes and the programme will proceed through to the end The safety lock is deactivated automatically at the end of the programme To deactivate the safety lock m Press the Start Stop button m Select De activate safety lock and confirm your selection 51 Delay start With delay start you ca
16. must sit firmly up against the housing Please also check this for the feet which did not need adjustment Otherwise there is the danger of the machine moving about Building under a continous worktop in a kitchen run The fitting of building under kits must only be undertaken by qualified and competent persons in accordance with the instructions supplied with the kit If you wish to push your machine under a worktop and there is space to do this without removing the lid the conversion kit is not necessary Otherwise it is essential The building under conversion kit includes a cover plate which must be fitted to ensure electrical safety When installing under a 900 910 mm high worktop a raising kit is required Connections for electricity water and drainage should be installed in such a way that they remain accessible when the machine is in place Fitting instructions are supplied with the conversion kit All parts marked are available from Miele 71 Installation and connection The Miele water protection system The Miele water protection system protects the machine from water damage The system consists of three main components 1 the inlet hose 2 the electronic unit and the machine housing 3 the drain hose 1 Inlet hose The inlet hose is tested to withstand pressure of more than 14 000 kPa thas a protective sleeve which is made from metal to protect t
17. reduces the drum action and is suitable for washing slightly soiled items more gently It should be activated for garments with a single bar under the care label and for articles which feel too hard after they have been dried Gentle action can be activated for the Cottons and the Minimum iron programmes If Gentle action is programmed into the machine every wash cycle in these programmes will be carried out with gentle action rhythm The machine is delivered with this option set at Off 82 Suds cooling When this is activated additional water flows into the drum at the end of the main wash to cool the suds down Hot suds can damage plastic drainage pipes Suds cooling takes place when temperatures of 95 C and 75 C are selected Suds cooling should be activated to prevent the danger of scalding if the drain hose is hooked over the edge of a sink or basin where the drainage pipes do not comply with DIN 1986 The machine is delivered with this option set at Off Distribution controller The maximum final spin speed is limited to prevent the laundry forming a ring against the drum This setting is only available when washing and drying in a continuous sequence There is a choice of 1200 rpm default setting 1100 rpm 1000 rpm and 900 rpm Settings menu Drying levels Anti crease The drying levels in the Cottons and Minimum iron programmes can be altered
18. that the machine has to offer Further programmes P Settings Dark garments m Use the V or A button to highlight the programme you wish to select and 20 confirm your selection by pressing the OK button m Press the Washing Drying button repeatedly until only the Washing indicator light is lit up The Drying indicator light must not be lit up as well as this would mean that the washing programme would be followed immediately by the relevant drying programme Cottons Duration 1600 rpm 1 49 h m Use the V or A button to alter the temperature Press the OK button to confirm the temperature selected and move on to the spin speed option Cottons 40 C Duration m Use the V or A button to alter the spin speed or to select No spin No amp WASHING O Select Extra option s OShort 3 O Water plus C Low O temperature OG S e OStains y Cs m Press the appropriate button to select Short or Water plus The relevant indicator light will come on m hen select any Further extras or the Stains option Example Further extras S O Extra quiet O Extra rinse m Use the V or A button to highlight the Extra you wish to select and confirm your selection by pressing the OK button A tick V will appear to show which Extra has been selected If you wish to deselect the Extra with a tick against it press the OK button again Press
19. the OK button m Select the option you want and confirm your selection A tick will appear beside the option to show that it has been set To close the Settings menu m Select Back and select OK to confirm your choice Language The display can be set to appear in one of several different languages You can select one of the languages displayed via the Languages sub menu The flag after the word Language acts as a guide to prevent a language which will not be understood from being set Buzzer When the buzzer function has been activated an audible tone sounds at the end of a programme or when Rinse hold is reached You can select one of two options or deactivate the buzzer Off the machine is delivered with this option selected as standard Normal The buzzer sounds at a normal volume Loud The buzzer sounds at a oud volume 79 Settings menu Time of day Select either a 24 hour or 12 hour clock and then set the current time of day Clock format m Use the V or buttons to select the way you want the time to be displayed and confirm your choice with the OK button Set the time of day m Set the hour with the V and buttons and confirm your setting by pressing the OK button Then do the same to set the minutes Temperature unit You can choose for the temperature to be displayed in C Celsius or F Fahrenheit The machine is delivered with the C opt
20. time the Miele Willkommen welcome screen will appear The welcome screen will not appear again once a programme lasting longer than 1 hour has been completed After a few seconds the display will change to show the screen for selecting your language 16 Setting the language Language english x m Use the V and buttons to select the language you want and confirm your selection by pressing the OK button Setting the time of day The display for setting the time will then appear m Set the hour with the V and A buttons and confirm your setting by pressing the OK button Then do the same to set the minutes After you have confirmed the minute setting the display will change to show the reminder to remove the transport bars Reminder to remove transport bars NTo avoid the risk of damage the transport bars must be removed before the washer dryer is used for the first time See Installation and connection for instructions on how to do this m After removing the transport bars if this has not already been done by your fitter press the OK button Before using for the first time Running your first programme Your washer dryer is now ready for the first programme to be run m Turn the programme selector to Cottons m Press the Start Stop button m At the end of the programme switch the machine off After running the first programme the load sensor has to be calibra
21. until the end of the programme before removing the laundry P Warning Do not switch the washer dryer off before the end of a drying programme If this is done and the laundry is then removed immediately it could give off a great amount of heat P Fabric conditioner and similar products must be used according to the instructions on the manufacturer s packaging P Oil affected items can ignite spontaneaously especially when exposed to heat sources such as in a tumble dryer The items become warm causing an oxidation reaction in the oil Oxidation creates heat If the heat cannot escape the items can become hot enough to catch fire Piling stacking or storing oil affected items can prevent heat from escaping and so create a fire hazard P If it is unavoidable that fabrics contaminated with vegetable or cooking oil or hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent this will reduce but not eliminate the hazard P Only use dyes specified by the manufacturer as being suitable for use in a domestic washing machine Always observe the manufacturer s instructions carefully 12 Warning and safety instructions P Colour run and dye removers contain sulphur compounds which can cause damage such as corrosion Do not use these products in this machine P Make sure that any dispensing balls etc are removed from the laundry before the drying programme Th
22. Building under a continous worktop in akitchenrun 0 71 The Miele water protection system 0 2 2 0 ees 72 Connection to the water supply 0 2 0 saa 73 Connection to the drainage system 6 sess 74 Electrical connections uses eere done e E ay REM RUP IR ee d 75 Consumption data iioii se 76 Consumption data for the nominated energy labelling programme according to AS NZS 2040 1 amp AS NZS 2040 2 Standard 0 0 2 0 0 000 eee 76 Notes for test institutes xus kn REOR EG ERA E Re ede 76 Notes for test institutes siiis TL Technical data eae se urge pata aaa Reale P d qe non 78 Settings menu iiuiuils iilii e 79 Lanouage M ck etc RE ETT E TTL E EET CO TIT T TT 79 B ZZ T DP 79 TWAS OFA PX D D 80 TSM S RATA asap pep EEPEET UEM 80 Brightness Contrast 0 0 n 80 standby display ike eerte dede ue hoe Gedeed ERU RR hee dg 80 Keypad TOME RET 80 LOCK COG TLLA 81 MEMORY y css pres Sede RA eh uon Sand RU AG ReMi A ARE ee Rl delta 81 Longer pre wash Cottons sosser ssns 2 00000 82 Gentle action lisse 82 SUdS COON s ueri etat po RR SCREENS Partie dete wea Pence dat 82 Distribution controller serres liiis es 82 Drying levels is dk yx eee vee RERSHERexA d EN RU Rs Pure gerade ds 83 Extended Cooldown cud se eR EPIS gd vag Pas PERRO Eb ed pe 83 ANUSCIEASC as edu sa xat et Repo ded a a esos P cR Oe e e RU IO es 83 Optional accessories lili lll e es 84
23. and cause damage to the dryer or the laundry The tap for the inlet hose must be turned on even when drying Q Start the programme m Press the flashing Start Stop button The estimated programme duration will appear in the display The electronics continually assess the residual moisture content of the laundry and adjust the estimated time remaining for a more accurate reading Because of this the time displayed can alter during the course of a programme The time left will count down by the minute in the 38 display The programme sequence and the drying level reached will also be shown in the display Q Remove the laundry when the programme has finished The Anti crease phase starts as soon as the programme finishes The machine will switch off automatically 15 minutes after the end of the Anti crease phase Push the D button to switch the machine back on m Turn the programme selector to Stop m Open the drum door and remove the laundry Check that all items have been removed from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is next used Important Always remove the laundry before switching the machine off This is important to ensure that the load size indicator works correctly m Switch off the washer dryer For more information see Washing and drying After each washing or drying programme DRYING Extras
24. art Stop button Colour run and dye removers dyes m Do not use colour run or dye removers in this machine m Dyes suitable for use in domestic washing machines can be used However please note that the salt used in the dyeing process can cause corrosion to stainless steel components in the machine if you dye frequently Follow the manufacturer s instructions carefully 35 DRYING Separate drying The separate drying programme must be used if the load in the wash programme is greater than the maximum load permitted for drying or if you only want to dry part of the load that was washed Tips on drying Do not put soaking wet items into the machine to dry them Spin them thoroughly after washing using the appropriate spin speed Woollens and wool blends tend to become matted and shrink if dried in a tumble dryer They can be partially dried using the Woollens programme Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise tend to roughen Loopknit garments e g T shirts and underwear tend to shrink depending on their quality Therefore Do not over dry these textiles When purchasing these garments it is advisable to take t
25. articularly stubborn stains ask your dry cleaner for advice N Do not use solvent based cleaning agents in this machine m Sort the laundry by colour and by care label Most garments have a textile care label in the collar or side seam Curtains Remove lead weights first or place in a laundry bag Underwiring and collar stiffeners Any loose wiring in bras shirt collar stiffeners etc should be removed or sewn in Close any zips fasten hooks and eyes etc before washing Wash light and dark coloured items separately Fasten duvet covers pillow cases etc to prevent small items from being rolled up inside them Do not wash items in this machine which are specified by the manufacturer as not washable on the care label WASHING Switch the machine on The interior drum lighting will come on The drum lighting will go out automatically after five minutes Press the Door button to switch the drum lighting back on again O Select a programme Further programmes Cottons Settings Warm air Minimum iron Denim Smoothing 2 Freshen up 25 Woollens t Express 20 Drain Spin___J pan Shirts Rinse out e M Automatic plus m Select the programme you want The programme selected will appear in the display Cottons Duration 1600 rpm 1 49h Further programmes Turn the programme selector to Further programmes Settings to display a list of other programmes
26. ck cover for contact details 84 CareCollection Miele specialist detergents Outdoor wear This specialist detergent will clean your water repellent outerwear with care Sportswear The Miele Sportswear detergent is designed to clean sportswear whilst taking care of special microfibres used in these garments It will help to neutralise and remove odours whilst protecting the colour of the fabric and preventing static build up Down Items This special purpose detergent contains a mild tenside and has been specially formulated to keep down filled items supple and to give them bounce Miele proofing agent This special finishing agent reproofs garments against wind and water and provides a dirt repellent finish whilst retaining elasticity and breathability Optional accessories UltraWhite detergent This multi purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items UltraColor detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments The special formulation offers effective stain removal even at low temperatures while helping to prevent colour fade Liquid detergent for Delicates This liquid detergent is ideal for the gentle treatment of delicate fabrics such as wool and silk Its special formulation cleans effectively at temperatures as
27. d electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P Do not connect the machine to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the washer dryer e g danger of overheating P Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician Ensure current is not supplied to the machine until after maintenance or repair work has been carried out Warning and safety instructions P In the event of a fault or for cleaning purposes the washer dryer is only completely isolated from the electricity supply when itis switched off at the wall socket and the plug is withdrawn or itis switched off at the mains or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable P The Miele Water protection system protects from water damage provided the following conditions have been met the machine is correctly plumbed in and connected to the electricity supply if a fault has been identified the machine must be examined by a competent person before further use and repaired if necessary P Faulty components must only be replaced by genuine Miele original spare parts Only when these parts are fitted can
28. e door seal and porthole glass after drying Check that all items have been removed from the drum Items left behind could colour run shrink or be damaged in the next washing or drying programme Important Always remove the laundry before switching the machine off This is important to ensure that the load size indicator works correctly m Switch the machine off using the On Off button D To avoid the build up of mildew it is recommended that the door is left ajar when the machine is not in use Rinse out fluff programme The fluff which occurs during drying can collect in the drum and also in the suds container It is best to rinse out this fluff before the machine is used again so that it cannot be deposited on the next load e g fluff from dark garments being deposited on lighter coloured items or cause a blockage The Rinse out fluff programme must not be used for rinsing laundry Make sure that there are no items of laundry in the drum before starting this programme m Switch the machine on m Turn the programme selector to the Rinse out fluff programme If there is a lot of fluff in the machine select the Water plus Extra option m Press the Start Stop button The fluff will be rinsed out after a few minutes m Remove any fluff remaining from around the door seal and porthole glass m Switch the machine off The load sensor will have to be recalibrated after running the Rin
29. ecting delay start 4 PC Optical interface This is used by Miele service technicians during servicing work for testing purposes Load Detergent button For displaying the load size or the recommended amount of detergent and for calibrating the load size sensor to zero 14 Warm air O Washing ODrying Denim Cc Smoothing amp V OK o Euren O Water plus meme Woollens amp 4 Gs Gs Gs 0 C Express 20 OStart Stop o6 o wtheres stains ep Pain Spin Shirts um gt CI Rinse out m Automatic plus Door Extra option buttons Programme selector For selecting washing and drying programmes Washing Drying button for selecting Washing Drying Washing and Drying 9 button For switching the washer dryer on and off To save energy the machine will switch itself off automatically 15 minutes after the end of the programme anti crease phase or after being switched on if no other selection is made Door button Opens the machine door Guide to the machine Display Ww OK TD 2D The display is operated using the V OK and buttons The value or option currently selected will appear highlighted Press button V to decrease a value in the display or to scroll down to the next option Press button to increase a value in the display or to scroll up to the next option Press the OK button to confirm
30. ed and spun or dried before proofing For optimum results the proofing agent should be heat treated by drying the garment in the drying cycle or by ironing it Extra options Extra quiet Rinse hold Soft toys cold to 40 C Max load 1 0 kg Suitable for Soft toys specified as machine washable by the manufacturer Note Do not wash soft toys stuffed with straw Extra options Stains Extra quiet Extra rinse Rinse hold Hygiene 30 to 90 C Max load 5 5 kg Suitable for Cotton and linen fabrics which have been in direct contact with the skin e g underwear nappies towelling bed linen pillow and mattress covers or where high standards of hygiene are required Notes If possible select a temperature above 40 C Observe instructions given on the care label Extra options Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold First wash cold to 40 C Max load 3 0 kg Suitable for New items made of cotton towelling and polyester fabrics Note Use this programme to wash any chemical residues out of new items Extra options Water plus Extra quiet Extra rinse Rinse hold 29 WASHING Silks w cold to 30 C Max load 1 0 kg Suitable for Silks and other handwashable fabrics with no wool content Note Place socks tights bras etc in a washing bag Extras Water plus Extra rinse Rinse hold
31. ed useless and the cable cut off directly behind the appliance or the machine to prevent misuse Contents Caring for the environment 0 0 00 ccc eee 2 Warning and safety instructions 0 0 0 6 Guide to the machine 0 00 00 14 Gontrelpahiel sss scs sped ERE E EET ed bu eis Iba tae a 14 BIET LC rU 15 Sc Iur 15 Before using for the first time lol iile e lesen 16 Calibrating the load size sensor to Zero iil eiie 17 Washing and drying environmentally and economically 18 WASHING 2 0 teeta 19 SNOKINSHUCTIONS 24 002 cn eren chose ederet begs Edo ues det 19 Separate washing 0 0 tees 19 Extra ODUONS 24 eub o dr pane bee ddan gd hag ib bw eed ote wale oe 24 SOM EE OE EEE EEEE ERA doe Rt alte ENE SEEE EE Acie TE 24 Mater plugs vie ok eter santas ene chek ERS AKENDE AA e a 24 SIRE cong ates ayer mentee nas Aime IL TET T OTT 24 F rther extras ce esae nine x Rod EP ER Rp ARR ADR qur wR e eras 24 Extra quiet a crise errre Ec UAR EY Shaw UR dle FERRO e ce rd 24 Extra TINS Orarul pe dee eed eta mde eg be ea Rx ve ee uem UR 25 Pre WaSliie RP PLI UIT 25 SO0dk i2 xxx eor ad REN GON dex P TOt e edt pons det os CR dre ee 25 Hinseolg i cux aos gest ocn ot EC Re ORC EO ad SORTA TUPHUR Td 25 Adding or removing laundry after a programme has started 25 PAM AU SPIN spoeg i ea aye acca tates eet eg pate e Gece ett aut oe aetna Eanes eae a 26 Fin
32. er and in future add washing powder and then add the water softener The fabric softener is not completely dispensed or too much water remains in the amp compartment The siphon tube is not correctly positioned or is clogged up Clean the siphon see Cleaning and care Cleaning the detergent dispenser drawer The display is in a different language A different language has been selected in Settings Language Set the language you want The flag symbol will guide you Foam escapes from the detergent dispenser drawer during the Rinse out fluff programme Detergent residue is located in the suds container after the last wash programme Always add the correct amount of detergent Use the Load Detergent button to assist with this Different durations are shown in the display The time remaining display constantly adjusts according to the washing and drying conditions 59 Problem solving guide An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result Liquid detergents usually contain no bleaching agents They do not remove fruit coffee and tea stains Use a general purpose detergent containing a bleaching agent Pour stain removers into compartment VI and liquid detergnent into a dispenser ball remember to remove the dispensing ball before drying Never put stain removers
33. ero again see above section The following will appear in the display Zero setting not possible Open the door The drum door is closed Open the drum door Recalibrate the sensor to zero again The drying programme stops and the following message appears in the display Check load There is very little or no laundry in the drum Drying individual garments or items which are already dry can also cause the programme to be cancelled In future use a timed drying programme or the Warm air timed drying programme for individual items At the end of a drying programme the following message appears in the display Check load The machine has recognised an overload In future do not exceed the maximum load 58 Problem solving guide General problems Problem Possible cause Remedy The machine shakes during the spin cycle The machine feet are not level Level the machine see Installation The pump makes strange noises This is not a fault These noises occur at the beginning and at the end of a pump sequence as a normal part of the operation Large amounts of detergent residue remain in the detergent dispenser drawer The water pressure is too low Clean the water inlet filters Select Water plus Powder detergent used with water softeners can be Sticky Clean the detergent dispenser draw
34. ese dispensers can melt during the drying programme and cause damage to the machine and the laundry Do not use liquid dispenser balls or similar if you are planning to wash and then dry in one continuous sequence P Textiles which have been pre treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the washer dryer P Never use solvent based cleaning agents e g those containing benzene in this machine as this may result in damage to component parts and create toxic fumes Such agents also pose a fire and explosion hazard P Take care the metal cap is hot after drying Open the door wide after the drying cycle Do not touch the metal cap located on the inside of the door glass It will still be hot and could cause a burn Accessories P Accessory parts may only be fitted when expressly approved by Miele If other parts are used warranty performance and product liability claims will be invalidated Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Guide to the machine Control panel Further programmes Stop Settings Cottons Minimum iron Load Detergent OShort Start Stop button For starting the programme selected and cancelling a programme once it has started 2 Display with V OK and buttons See the following page for more information 33 button For sel
35. etergent recommended by the manufacturer on the packaging Reduce the amount of detergent for smaller loads Use the Load Detergent button Choosing the correct Extra option Pre wash Soak Short Select Awash programme together with the Short Extra option for light to normal soiling where there are no obvious marks Awash programme without any Extra options for normal to heavy soiling Awash programme together with the Soak Extra option for very heavily soiled laundry The Pre wash Extra option for laundry with large amounts of dirt e g dust sand When drying straight after washing Select a high spin speed for the wash programme as well as for the Thermospin to save time and energy WASHING Short instructions The headings numbered show the operating sequence and can be used as brief instructions Separate washing Q Sort the laundry m Empty all pockets Foreign objects e g nails coins paper clips etc can cause damage to textiles and to components in the machine m Badly soiled areas stains etc should be cleaned as soon as possible preferably whilst still fresh Spillages should be carefully dabbed off using a soft colourfast cloth Do not rub Badly soiled areas can be pre treated with liquid detergent stain removers etc first following the manufacturer s instructions You can also use the Stains Extra option With p
36. floor gully If required the drain hose can be extended to a length of 5 m The necessary parts can purchased from Miele or your Miele Chartered Agent 74 This appliance incorporates backflow protection complying with ATS 5200 101 No further backflow protection is required for connection to the water supply Installation and connection Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations Ensure power is not supplied to the appliance until after installation work has been carried out The appliance is supplied with a mains cable with moulded plug ready for connection to a 230 240V mains supply Please ensure the connection data quoted on the data plate match the household mains supply Connection should be made via a suitable switched socket which is easily accessible after installation For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electrician for advice Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating WARNING THIS APPLIANCE MUST BE EARTHED 75 Consumption data Consumption data for the nominated energy labelling programme according to AS NZS 2040 1 amp AS NZS 2040 2 Standard Load Consu
37. for Cottons and linen fabrics which are in direct contact with the skin e g underwear nappies towelling bed linen pillow and mattress COVers Important Because the temperature is held for longer the laundry will feel drier Extras Thermospin Extra quiet First wash Max load 2 5 kg Normal Normal Hand iron Smoothing Timed drying Suitable for New items made of cotton towelling and polyester fabrics Extras Thermospin Silks Max load 1 0 kg 5 minutes Suitable for Silks suitable for drying in a tumble dryer e g blouses and shirts Note Smooths out creasing Garments are not totally dried in this programme Remove garments immediately at the end of the programme Pillows 2 pillows 40x80 cm or 1 pillow 80x80 cm Timed drying Suitable for Pillows suitable for drying in a tumble dryer with feather down or synthetic fillings Note Please observe the instructions on the care label Pillows can still feel damp after being dried You can use this programme several times until the pillow feels dry Cool air Max load 2 5 kg Timed drying Suitable for Any item which only needs airing 45 DRYING Smoothing Garments are dampened before the programme starts to help reduce creasing Textiles are not completely dried in this programme to make them easier to iron The drying temperature is determined by the prog
38. he hose from damage 2 Electronic unit and machine housing Sump Any leaking water is collected in a sump in the base of the machine A float switches off the safety valves preventing any more water flowing into the machine and water in the suds container is pumped away 72 Overflow protection This prevents the maching taking in too much water If the water level exceeds a certain level the drain pump switches in and pumps the excess water away 3 Drain hose The drain hose is protected by a ventilation system which prevents the machine from being emptied completely Installation and connection Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations The machine is designed to operate with a flow pressure of between 100 kPa and 1 000 kPa If it is higher than 1 000 kPa it is essential to fit a reducer valve Connection to the mains water supply should incorporate a mains tap with 3 4 thread The tap should be fitted by a qualified plumber The connection point is subject to mains water pressure Turn on the tap slowly and check for leaks Correct the position of the washer and union if appropriate This machine is not suitable for connection to a hot water supply and connection to a household water softener is not recommended Maintenance and care Only use a genuine Miele hose which is pre
39. he programme will continue automatically The time left shown in the display may now vary from the actual drying time The door cannot be opened if the temperature in the drum is over 70 C the programme has reached the Spin stage The safety lock has been activated 40 DRYING Programme chart Cottons Max load 2 5 kg Extra dry Normal Normal Suitable for Single and multi layered cotton fabrics such as T shirts underwear towelling flannelette bed linen Note Do not use Extra dry for loopknit fabrics as they have a tendency to shrink Extras Low temperature thermospin Extra quiet Hand iron 6 Hand iron Machine iron Smoothing Timed drying Suitable for Cotton or linen fabrics e g table linen bed linen starched laundry etc Note To prevent laundry from drying out it should be rolled up until you are ready for ironing Extras Low temperature thermospin Extra quiet Minimum iron Max load 1 5 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Minimum iron items made of synthetic or blended fabrics e g tops blouses skirts and table cloths Extras Low temperature thermospin Extra quiet Denim Max load 2 5 kg Extra dry Normal Normal Hand iron 4 Hand iron Machine iron Smoothing Timed drying Suitable for Denim garments e g jeans jackets skirts shir
40. he safety lock has been activated 25 WASHING Final spin speed To omit the final spin Rinse hold m Select the Rinse hold Extra Programme rpm Cottons 1600 Minimum iron 1200 Denim 900 Woollens 1200 Express 20 1600 Shirts 600 Automatic plus 1200 Dark garments 1200 Delicates 600 Sportswear 1200 Trainers 1000 Outerwear 800 Proofing 1000 Soft toys 900 Hygiene 1600 First wash 1200 Silks 600 Pillows 1200 Curtains 600 Separate rinse 1600 Starch 1600 Drain Spin 1600 You can reduce the final spin speed However you cannot select a final spin speed higher than that shown in the chart above Rinse and interim spin There is a spin after the main wash and between the rinses A reduction in the final spin speed will also reduce the interim spin speed In some programmes an additional rinse is introduced if a spin speed of less than 700 rpm is selected 26 To start the final spin The machine will display the previously set spin speed You can change this to a different spin speed if you wish Start the final spin by pressing the Start Stop button To end the programme Press the Door button The water will drain away Press the Door button again to open the door To omit the spin between rinses and the final spin m Select the No option The laundry is not spun after the final rinse The water
41. heir shrinkage properties into account 36 Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch that should be used New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments Dark coloured fibres can also settle on light coloured garments and vice versa Q Sort the laundry m Sort the laundry according to type of fibre weave and the residual moisture content This will help achieve an even drying result m Before drying check the drying symbol on the care label Dry at normal temperature Dry at a low temperature select the Low temperature Extra option K Do not tumble dry If the care label does not have a drying symbol on it the item should only be dried in a programme named as suitable for it Using the Cottons Normal programme is recommended for a mixed cotton load and is the programme used in energy consumption tests to AS NZS 2442 Refer to consumption data DRYING O Switch on the washer dryer O Select a programme up otherwise the corresponding wash programme will begin before Further programmes Cottons Settings Warm air Minimum iron Smoothing 2 1600 rpm Freshen up 2 Express 20 Duration 1 26 h Drain Spin ___J Shirts 5 irts GE m You can change the drying level b Rinse o
42. ical fault Call Service There is a fault Start the programme again If the fault message appears again contact Miele Chk detergent Excessive foam has built up during washing Use less detergent next time and follow the manufacturer s instructions on dosage given on the packaging Q To remove the message from the display switch the machine off using the On Off button D 57 Problem solving guide Problems with the load size indicator Problem Possible cause Remedy The display indicates a load of lt 25 or no load size is indicated when the drum is full Laundry was left in the drum when the machine was switched off This has decalibrated the sensor from the zero setting To recalibrate the sensor to the zero setting Remove the laundry from the drum Switch off the machine and leave the door open Switch on the machine The load sensor has to be recalibrated to zero after running the Rinse out fluff programme Turn the programme selector to Cottons Press and hold the Load Detergent button in until the following message appears in the display Zero setting OK The display indicates a load greater than lt 25 when the drum is empty The load size sensor has been decalibrated from the zero setting Rotate the drum once If the display still indicates a load greater than lt 25 recalibrate the sensor to z
43. iled cotton garments Extras Water plus Extra quiet Extra rinse Rinse hold the Short option is activated automatically Shirts cold to 60 C Max load 1 5 kg Notes Pre treat collars and cuffs if necessary Wash silk blouses and shirts in the Si ks programme Extra options Short Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold Please note that the buckets represent garment care label symbols See Garment care label symbols 27 WASHING Automatic plus 40 E G5 Ba cold to 40 C Max load 4 5 kg Suitable for Mixed loads of garments suitable for the Cottons and Minimum iron programmes Sort according to colour Note The wash parameters are adjusted automatically in this programme to ensure the best possible care and wash results for each item Extra options Stains Extra quiet Rinse hold Dark garments cold to 40 C Max load 3 0 kg Suitable for Dark garments made from cotton or mixed fibres Note Wash inside out Extra options Short Water plus Stains Extra quiet Pre wash Soak Rinse hold Delicates JEJL 35 39 30 cold to 60 C Max load 1 5 kg Suitable for Delicate garments made of synthetic fibres mixed fibres rayon and easy care cottons Note Select No for items which crease easily Extra options Short Stains Extra quiet Pre wash Soak Rinse hold Sportswear cold to 60
44. inal values given depending on water pressure water hardness water inlet temperature room temperature type and volume of load fluctuations in the electricity supply and any Extra options selected 77 Technical data Height Width Depth Depth with door open Height for building under Width for building under Depth for building under Weight Capacity Washing Capacity Drying Voltage Rated load Fuse rating Consumption data Minimum water flow pressure Maximum water flow pressure Inlet hose length Drain hose length Mains connection cable length Delivery head max Maximum drainage length LEDs Test certificates awarded 78 850 mm 595 mm 580 mm 975 mm 820 mm 600 mm 600 mm 101 kg 5 5 kg dry laundry 2 5 kg dry laundry See data plate See data plate See data plate See Consumption data 100 kPa 1 bar 1000 kPa 10 bar 1 60 m 1 50 m 1 60 m 1 00 m 5 00 m Class 1 See data plate Settings menu The Settings menu is used to alter the machine s electronics to suit changing requirements Settings can be altered at any time To open the Settings menu m Switch the machine on m Turn the programme selector to Further programmes Settings Further programmes Settings P Dark garments m Confirm with OK To select a setting m Use the V and buttons to scroll through the settings until the one you want is highlighted and then confirm your choice by pressing
45. ion selected Brightness Contrast There are ten different display settings The machine is delivered with this option set at level 5 The display contrast brightness will change as soon as a different setting is chosen 80 Standby display To save energy the display goes out and the indicator light for the Start Stop button starts flashing slowly The display will always go out if a programme is not selected within 10 minutes of the machine being switched on 10 minutes after the end of a programme Pressing one of the buttons switches the display back on again You can also choose whether you want the display to go out 10 minutes after a programme has started or to remain visible throughout the programme On Standby comes on The display will go out 10 minutes after a programme has started Not in current prog the machine is delivered with this option selected Standby is switched off The display will remain visible during a programme Keypad tone An audible tone sounds each time a button is pressed The machine is delivered with this option set at Off Settings menu Lock code The code prevents the machine being used without your knowledge When the code has been activated you have to enter a code after switching the machine on Otherwise it cannot be operated To activate the lock code Lock code Back gt m Select Activate and conf
46. irm your selection The display will now request that a code is entered The code is 125 and cannot be altered Enter the lock code Lock code Moo m Use the V or button to change the first digit Confirm your selection by pressing the OK button Now enter the second digit m Repeat the process until all three digits have been entered and confirm your entry of the last one by pressing the OK button m Once the machine is switched off it can only be used again if the lock code is entered The lock will now be activated when the machine is switched off To unlock the machine When the machine is switched on again the display will request the code m Enter code 125 as described above and confirm the entry The machine is now unlocked To deactivate the lock code Proceed as for activating the lock code Memory If an Extra option has been selected for a programme or the recommended spin speed has been altered the machine will store the changes in memory at the start of a programme When this programme is chosen again these settings will appear in the display The machine is delivered with this option set at Off 81 Settings menu Longer pre wash Cottons The pre wash duration can be extended in the Cottons programme If you require a longer pre wash an additional 6 9 or 12 minutes can be added to the standard 25 minutes Gentle action Activating gentle action
47. lar basis m Pull out the detergent dispenser drawer until a resistance is felt Press down the release catch and at the same time pull the drawer right out of the machine m Clean the detergent drawer with warm water 53 Cleaning and care Cleaning the detergent dispenser drawer housing m Clean the siphon 1 Remove the siphon from compartment amp and rinse under warm running water Clean the siphon tube in the same way m Use a bottle brush to remove detergent residues and limescale from the jets inside the detergent dispenser drawer housing 2 Replace the siphon If starching frequently thoroughly clean the siphon and siphon tube regularly A build up of starch will cause them to get clogged 54 Cleaning and care Cleaning the porthole glass m From time to time you should also clean the door glass on the inside using a mild detergent or soap and water the metal cap on the inside of the door glass with a suitable proprietary stainless steel cleaning agent following the manufacturer s instructions on the packaging m Wipe dry using a soft cloth Cleaning the filter in the water inlet The machine has a filter to protect the water inlet valve The accessible filter in the union in the open end of the inlet hose should be checked every six months or more often if there are frequent interruptions to the external water supply m First turn off the tap and
48. lease note the following points m The machine must be level and securely positioned m To avoid vibrations during spinning the machine should not be installed on soft floor coverings If installing on a wooden joist floor m We recommend a plywood base at least 59x52x3 cm The base should span several joists and be bolted to the joists and not only to the floorboards Check for the presence of pipes and cables first If possible install the machine in a corner as this is usually the most stable part of the floor ANI the machine is installed on a raised plinth it has to be secured against slippage during spinning using retaining clips available from Miele 68 Installing the washer dryer To manoeuvre the machine out of its packing case to its installlation site hold it by the edge of the lid where it protrudes to the rear of the machine as well as by the handle recesses at the front Please note m Do not lift the machine by the drum door N Ensure that the machine feet and the floor are dry to prevent the machine from slipping during the spin cycle Removing the transit fittings m Toremove the left and right covers 1 Use a screwdriver to prise out the cover as illustrated 2 Pull the cover forwards to remove Installation and connection EI Z o m Using the spanner supplied turn the m Turn the right hand transit bar 90 left hand transit bar 90 then then
49. low as 20 C while protecting the colour of your delicate garments Fabric conditioner The Miele fabric conditioner will give your laundry a fresh natural fragrance It makes garments soft to handle and prevents static cling during tumble drying 85 86 87 Miele Australia Pty Ltd ABN 96 005 635 398 Head Office Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Miele Gallery and Office Melbourne 208 210 Coventry Street South Melbourne VIC 3205 Miele Gallery and Office Sydney 3 Skyline Place Frenchs Forest NSW 2086 Miele Gallery and Office Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Miele Gallery and Office Adelaide 83 85 Sir Donald Bradman Drive Hilton SA 5033 Miele Gallery and Office Perth 205 207 Stirling Highway Claremont WA 6010 1300 4 MIELE 1300 464 353 www miele com au Miele www miele shop com Miele New Zealand Limited Miele Gallery and Head Office Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland New Zealand Telephone 0800 264 353 www miele co nz Miele Global Headquarters Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Federal Republic of Germany Alteration rights reserved 5012 Ce M Nr 09 441 860 00
50. m continues to turn at intervals for up to 30 minutes to help prevent creasing Exception There is no anti crease phase in the Woollens programme The door can be opened and laundry removed at any time during the anti crease phase 1 A second rinse is carried out when a temperature of 60 C to 95 C has been selected A third rinse is carried out when a temperature below 60 C is selected 2 A third or fourth rinse is carried out if there is too much foam in the drum aspin speed lower than 700 rpm has been selected No has been selected A third rinse is carried out if No has been selected There is a spin only after the main wash Run up to spin A run up to spin is carried out before the wash process begins to deflate the pillows S Pre wash A pre wash is carried out automatically to remove dust WASHING Detergent Universal detergent Detergent for coloureds Detergent for delicates Specialist detergent Proofing agent Fabric conditio ner Cottons X Minimum iron Denim ES c ES X Woollens Express 20 Shirts Automatic plus Dark garments Delicates 2X gt lt X gt lt X X X X X X X Sportswear x Ex lt x X lt Trainers Outerwear Proofing Soft toys Hygiene First wash x lt X Silks Pillows Curtains
51. mption data Energy Water Duration in kWh in litres Normal Cold Water Cottons 40 C 5 5 kg 0 55 51 1h51 min Notes for test institutes Detergent must be dispensed via the detergent dispenser drawer Consumption data can vary from the nominal values given depending on water pressure water hardness water inlet temperature room temperature type and volume of load fluctuations in the electricity supply and any Extra options selected 76 Consumption data Load Consumption data Energy Water Duration in kWh in litres Short Normal Washing Cottons 95 C 5 5 kg 1 75 45 2 h 03 min 60 C 5 5 kg 0 93 45 1h 43 min 60 C 3 0 kg 0 73 39 48 mi 40 c 5 5 kg 0 55 51 1h51 min 40 C 3 0 kg 0 36 39 38 mi Minimum iron 40 C 3 0 kg 0 47 50 47 mi 1 h 08 min Delicates 30 C 1 5 kg 0 33 65 46 mi 56 min Automatic plus 40 C 4 5 kg 0 50 55 1 h 29 min Express 20 40 C 3 0 kg 0 30 26 20 mi Woollens W 30 C 2 0 kg 0 23 39 39 min Silks W 30 C 1 0 kg 0 25 39 35 min Drying Cottons Normal 2 5 kg 1 48 13 1 h 28 min Minimum iron Normal 1 5 kg 0 75 39 min Washing and Drying Cottons 60 C 5 5 kg 3 74 69 4 h 30 min Normal 2x2 5 kg Cottons 60 C 2 5 kg 2 50 52 2h32 min Normal 2 5 kg Notes for test institutes 1 AS NZS 2040 1 amp AS NZS 2040 2 2 AS NZS 2442 1 amp AS NZS 2442 2 Consumption data can vary from the nom
52. n choose when you want the programme to end The start of a programme can be delayed from 30 minutes up to a maximum of 24 hours The current time of day needs to have been set for Delay start to work correctly Select Delay start m Select the programme you want and then press the button Delay start Start time Finish time The display shows the current time of day and the time the programme is due to end m Use the A button to select the time you want the programme to end at Delay start Start time Finish time The first press on the button will adjust the programme end time to the next 15 30 45 minutes or full hour Each subsequent press on the button will delay the programme end time by 15 minutes m Confirm your selection by pressing the OK button 52 To begin Delay start m Press the Start Stop button Altering Delay start m Press the button m Use the V or buttons to change the programme end time m Confirm your selection by pressing the OK button Cancelling delay start m Press the Start Stop button m Cancel delay start will appear in the display m Confirm with OK m Press the Start Stop button to start the programme straight away or select a different programme The actual load size can only be determined accurately by the machine once the programme has started The programme end time may therefore be a bit later or earlier than first indicated
53. nd loosen the laundry Start the drying programme again using a lower spin speed Warm laundry feels damp Extend the cool down time as described in the Settings menu The laundry is too damp or too dry after a drying cycle When laundry is dry it feels hard to the touch The required residual moisture level is between two drying levels Too vigorous wash action Change the drying levels as described in the Settings menu Programme in gentle action and more water Not enough detergent was used Increase detergent dose to prevent limescale build up in laundry No fabric conditioner was used Use fabric conditioner in last rinse There is still water in the drum after drying There is a blockage in the water outlet Clean the drain filter and the drain pump as described in Problem solving guide Opening the drum door in the event of a blocked drain outlet and or power failure 61 Problem solving guide The drum door cannot be opened by pressing the Door button Problem Remedy The machine is not connected to the electricity supply and or is not switched on Insert the plug in the socket and switch on and or switch the machine on with the button The safety lock has been activated Deactivate the safety lock as described in Changing the programme sequence Safety lock Access via a code has been activated
54. ne do not unscrew the drain filter completely or take it right out m Unscrew the drain filter lid until water runs out To interrupt the flow of water m lighten the drain filter back up again 63 Problem solving guide Once the flow of water ceases To activate the ball valve and prevent a loss of washing detergent pour approx 2 litres of water through the detergent dispenser drawer after cleaning the drain filter Opening the drum door N Always make sure that the drum is stationary before reaching into the machine to remove laundry Reaching into a moving drum is extremely dangerous m Remove the drain filter completely m Clean it thoroughly m Pull the emergency release downwards see illustration The drum door will open m Remove any foreign objects e g buttons coins etc and fluff from the filter housing Turn the impeller by hand to check that it rotates freely m Put the drain filter back in place and secure A Make sure the drain filter is securely tightened Otherwise there is a risk of water leakage during use 64 After sales service In the event of any faults which you cannot remedy yourself please contact your Miele Chartered Agent or Miele see back cover for contact details When contacting Miele please quote the model and serial number of your appliance both of which are shown on the data plate visible above the do
55. o be left for any length of time e g holiday especially if there is no floor drain gully in the imme diate vicinity P Flooding danger If hooking the drain hose into a wash basin check that the water can drain off quickly enough to prevent the sink from overflowing Make sure the drain hose is secure so that the force of the water flowing out of the hose does not dislodge it P Take care to ensure that foreign objects e g nails pins coins paper clips do not find their way into the machine with the laundry These may damage components of the machine e g suds container drum which in turn can result in damage to the laundry P If the correct amount of detergent is dispensed the machine should not need to be descaled If however you do wish to descale the machine only use proprietary non corrosive descaling agents and strictly observe the instructions on the packaging A Miele descaling agent is available to order see Cleaning and care 10 Warning and safety instructions P To prevent the risk of fire the following must not be dried in this washer dryer items which have not been washed items such as workwear which have not been thoroughly cleaned and which are still soiled with grease oil or other deposits such as cosmetics lotions etc If items have not been thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the washer dryer at
56. or glass when the door is open Future updates PC The indicator or check light marked PC is the interface used by Miele service technicians during servicing work for testing purposes and for updating the machine s programme data Appliance warranty Please see the warranty card supplied with your machine Optional accessories Optional accessories for this machine are available from your Miele Chartered Agent or from Miele Please note that telephone calls may be monitored and recorded for training purposes 65 Installation and connection Front view Inlet hose with flexible waterproof Detergent dispenser drawer metallic outer sleeve Drum door Electricity supply cable 4 Access to drain filter drain pump Flexible drain hose with and emergency release Getae SUIVI Handle recesses for moving the Control panel machine amp 2 Four height adjustable feet 66 Installation and connection Rear view bo BIA s E Ej Protruding lid for holding when moving the machine 2 Electricity supply cable 8 Transit bar covers Inlet hose with flexible waterproof metallic outer sleeve Drain hose 67 Installation and connection Installation surface A concrete floor is the most suitable installation surface being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface P
57. pending on this absorbency rate The programme sequence is also shown in the display The washer dryer shows you when each section of the programme is reached The drum lighting switches off once the programme has started O Remove the laundry when the programme has finished The anti crease phase starts as soon as the programme finishes The machine will switch off automatically 15 minutes after the end of the anti crease phase You will need to press the I button to switch it back on again m Turn the programme selector to the Stop position m Open the drum door and remove the laundry Check that all items have been removed from the drum Items left in the drum could discolour other items in the next wash or become discoloured themselves Important Always remove the laundry before switching the machine off This is important to ensure that the load size indicator works correctly m Switch the machine off using the D button See After each washing or drying programme in WASHING AND DRYING for further information After washing a full load If you have washed a full load of laundry and you wish to dry the laundry in the washer dryer afterwards you will have to remove half the load Carry out the drying procedure in two batches 23 WASHING Extra options You can use the Extra option buttons to augment the basic wash programmes Short For light to nomal soiling wi
58. pin speed displayed for washing will be adopted for the thermospin If you select Extra quiet spinning will not exceed 900 rpm The thermospin is not carried out when the Low temperature Extra option has been selected m Select Delay start if required 47 WASHING AND DRYING Load the drum m Open the drum door and load the laundry loosely in the drum Follow the load size indicator and do not overload Do not use detergent dispensing aids e g plastic dispenser balls for washing followed immediately by the drying programme These dispensers can melt during the drying programme and cause damage to the machine and the laundry Close the drum door Q Add detergent Follow the detergent percentage display Q Start the programme m Press the Start Stop button Remove the laundry when the programme has finished m Turn the programme selector to the Stop position m Open the drum door and remove the laundry See After each washing or drying programme for further information 48 After each washing or drying programme m Open the drum door fully A Caution the metal cap located on the inside of the door glass is very hot after drying Do not touch it It will be hot Danger of burning m Remove the laundry m Check the folds in the door seal for any small articles e g buttons which might be lodged there Remove any fluff remaining from around th
59. pped You are asked to enter a code Access via a code has been activated See the Settings menu Enter the code and confirm the entry Deactivate the code if you do not wish this message to appear in the display the next time the machine is switched on The programme does not start when Drain Spin has been selected The machine has not been prepared for using for the first time Prepare the machine as described in Before using for the first time The display is dark The display has switched off automatically to save energy Standby mode Press a button The machine comes out of standby mode 56 Problem solving guide A fault message appears in the display Message Possible cause Remedy Fault The water outlet is Clean the drain filter and EJ ES drainage blocked or the drain pump as pem restricted described in Problem The drain hose has solving guide Opening been fixed too high the drum door in the event of a blocked drain outlet and or power failure The maximum drain height is 1 m Fault The water inlet is Check whether Water intake Open stopcock blocked or restricted the tap is opened wide enough the inlet hose is kinked If the fault indicator occurs again contact Miele Waterproof system activated Close the stopcock 2 The water protection System has reacted Close the tap Call Miele Techn
60. r programmes with a pre wash you will need to purchase a special container from Miele which sits in the main wash compartment UL of the detergent dispenser drawer Add liquid detergent to this container for the main wash and to compartment LU for the pre wash See Optional accessories at the end of this booklet for details of Miele branded care products including detergents and fabric conditioner The right amount to dispense will depend on the following The soiling level of the laundry Lightly soiled No visible dirt or stains Possibly slight body odour Normally soiled Visibly dirty and or just a few slight stains 34 Heavily soiled Visible dirt and stains and or dried on soiling The quantity of the laundry add the recommended amount of detergent The water hardness level Check with your local water supplier if you do not know the hardness level in your area Water softeners A water softener can be used to cut down on the use of detergents in hard water areas Dispense according to the amount specified on the packaging First add detergent and then the water softener Use the same quantity of detergent as for soft water Miele do not recommend connecting the machine to a household water softener Washing with several components If you wash using several components e g special application detergents we recommend always dispensing the agents into compartment UH in the follo
61. ramme being used 2 Timed drying Timed dring is particularly suitable for small loads and for drying individual items Garments are dried in warm air times of between 15 minutes and 2 hours can be selected The drying temperature is determined by the programme being used Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time 46 WASHING AND DRYING Washing and drying ina continuous sequence Where the amount of laundry to be washed and dried in one programme does not exceed the maximum weight permitted for the drying programme washing and drying in one continuous sequence is recommended It is very important to read both the Washing and Drying sections before proceeding Sort the laundry into colours and fabric types Switch the machine on O Select a programme m Turn the programme selector to the required programme m Press the Washing Drying button repeatedly until both the Washing and Drying indicator lights are lit up 1600 rpm 252 h m Select the temperature spin speed and drying level and confirm with OK To avoid the laundry forming a ring against the drum at the end of the washing programme the spin speed is limited to a maximum of 1200 rpm when washing and drying in a continuous sequence m Select the drying level or drying time you require m Now select Extra options if required The s
62. recommended amount 5 Add three quarters of the recommended amount 100 Add the recommended amount You also need to take the level of soiling and water hardness into account Too little detergent results in Laundry not getting properly clean and with time it may become grey and hard to the touch Greasy particles clinging to laundry Limescale deposits on the heater elements Too much detergent results in Excessive foam which causes a low level of agitation and poor wash rinse and spin results 22 High water consumption an additional rinse cycle will automatically switch in A burden to the environment m Pull out the detergent drawer and add detergent to the compartments as follows LU Detergent for the pre wash 1 4 of the total amount recommended Ull Detergent for the main wash including Soak if selected amp 8 Fabric conditioner or liquid starch m Close the detergent drawer See Detergent for further information WASHING Select Delay start If required please refer to Delay start for more information O Start the programme m Press the flashing Start Stop button The estimated programme duration will start counting down in one minute steps During the first few minutes the machine measures how much water is being absorbed by the laundry The programme duration may be longer or shorter de
63. se out fluff programme See Before using for the first time 49 Changing the programme sequence To cancel a programme You can cancel a programme at any time after it has started m Press the Start Stop button and select Cancel programme or turn the programme selector to Stop During washing The suds will be pumped away and the washing programme is cancelled During drying The garments will be cooled down before the door can be opened If you want to remove the laundry m Press the Door button If you want to select a different programme m Switch the machine off using the CD button m Check that there is still detergent in the detergent drawer Add detergent if necessary m Switch the machine back on again and select a new programme 50 Interrupting a programme m Switch the machine off using the button To continue with the same programme m Switch the machine back on again with the button N Do not switch the washer dryer off before the end of a drying programme If this was done and the laundry was then removed immedi ately it could give off a great amount of heat Changing a programme After the start of a programme it is no longer possible to select a different programme You will need to cancel the current programme before you can select a new one Altering the temperature You can alter the temperature of a washing programme up to 5 minutes
64. sexand Mermi Spiess rers race kc edo oce Xr Gee ne Ie eed et 26 To omit the final spin Rinse hold 2 2 eee 26 To omit the spin between rinses and the final spin 26 Programme Chart esses ere bbe bbe eee eS oe Re dope een a Sees 27 Programme sequeHee suat ans denunce den top RR RR OER BOR ROREM n e dra 31 Bowie t TP RTT CRAT ELT XT 33 Water softeners 0 0 0 0 s 34 Washing with several components iie 34 Fabric conditioner and liquid starch sccis iile 35 Colour run and dye removers dyes ie ess 35 DRYING eb Rer Wee eb e Sg A RE TRES ee ee ones 36 Separate dryg 4 iun aser oes e Ree 1 bee pe tie ES wer ad ei 36 Contents EXA S ee weet r 39 Low temperature sus cae era whandbadeg edad bee bee Foe edo ee hie ent 39 T OeFTIOSDIFI serne rnr anak ON ce ede e der n toe doe e deter wie ane 39 Extra quieti ias ety ee tbe DEA eed eab E RS de peek badd ets 39 Adding or removing laundry after a programme has started 40 Programme Chart ao aad serenus dens pk Rete eda need RUE p d da 41 WASHING AND DRYING usse 47 Washing and drying in a continuous sequence 00 02 bees 47 After each washing or drying programme 0 0 0000 c eee 48 Rinse out fluff programme 00 0 0 49 Changing the programme sequence 0 000 cee ees 50 Te caricel progtamlirie sexes gae daar be eee wer baw e Ue we
65. sher dryer is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning Its use by a person responsible for their safety Safety with children P Keep children away from the washer dryer at all times It is not a toy To avoid the risk of injury do not allow children to play on or near it or to play with its controls Supervise children whilst you are using it P Older children may only use the washer dryer if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse Warning and safety instructions Technical safety P Before setting up the washer dryer check it for any externally visible damage Do not install or use a damaged machine P Before connecting the washer dryer ensure that the connection data on the data plate voltage and rated load match the mains electricity supply If in any doubt consult a qualified electrician P The electrical safety of this washer dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualifie
66. ssure tested to 14 000 kPa should you ever need a replacement or extension In order to protect the water inlet valve the dirt filter in the water inlet valve connection must not be removed Extension hose A 1 5 metre long metal extension hose is available from your Miele Chartered Agent or Miele as an optional extra This hose is tested to withstand pressures of up to 14 000 kPa and can be used as a flexible extension to the water supply 73 Installation and connection Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre The drain hose must not be kinked as this restricts drainage The swivel elbow at the end of the hose can be turned in either direction or can be detached if required with a sharp twist and pull For a delivery head of more than 1m up to a max of 1 8 m a second duo drain pump is available with the corresponding kit from Miele or your Miele Chartered Agent Drain hose connection 1 Direct into a sink or basin Please note Hook the hose over the edge and secure Make sure that the water can drain away freely without hindrance Otherwise there is a risk of water overflowing or of some of the drained water being siphoned back into the machine 2 Connected securely to a plastic drain pipe with a rubber nipple There is no need to use a non return valve 3 Connected securely to a standpipe 4 Connected securely to a
67. t Delicates Max load 1 0 kg Normal Hand iron Timed drying Suitable for Delicate fabrics made of synthetic fibres mixed fibres easy care cotton shirts and blouses Extras Extra quiet Weight of dry laundry 43 DRYING Sportswear Max load 2 0 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Sportswear that is suitable for tumble drying Extras Thermospin Extra quiet Trainers Max 2 pairs of shoes Timed drying Suitable for Trainers specified as machine washable by the manufacturer Note The drum does not rotate during this programme Insoles should be removed and placed in the drum with the shoes Outerwear Max load 1 5 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Outerwear which is suitable for drying in a tumble dryer Extras Thermospin Extra quiet Proofing Max load 1 5 kg Normal Suitable for Thermally fixing textiles which are suitable for drying in a tumble dryer and have been treated with a proofing agent Extras Extra quiet Soft toys Max load 1 0 kg Timed drying Suitable for Soft toys that can tolerate being dried in a tumble dryer Note Observe the manufacturer s care label Weight of dry laundry 44 DRYING Hygiene Max load 2 5 kg Normal Suitable
68. ted to zero as you would with bathroom scales Calibrating the load size sensor to zero m Switch the machine on m Open the drum door m Turn the programme selector to Cottons m Press and hold the Load Detergent button in until the following message appears in the display Zero setting OK m Switch the machine off The machine is now ready for use Washing and drying environmentally and economically Energy and water consumption 18 Water consumption and energy usage are determined by the size of the load To make the most out of your machine load the maximum amount for the programme you are using Use the Automatic plus and Express 20 programmes for small loads When smaller amounts of laundry are washed using the Cottons programmes the automatic load recognition system will reduce the amount of water time and energy used This may mean that the time left shown in the display is adjusted during the course of the wash programme Using the Cottons 60 C programme instead of the Cottons 95 C programme will result in energy savings of between 35 and 4596 This is sufficient for most levels of soiling For stubborn or old soiling use the Soak Extra option Using the Cottons 40 C programme is recommended for a normally soiled load and is the programme used in energy water consumption tests to AS NZS 2040 Refer to consumption data Detergent Do not exceed the amounts of d
69. th no visible staining The duration of the main wash is reduced Water plus The water level in the main wash and the rinses will be increased Stains m Press the Stains button There is a choice of various types of stains for achieving the optimum wash results With some stains a tip about pre treating the stain will appear in the display You can select a maximum of three stains for a wash programme If the Short Extra option has been selected it will be deselected automatically Press the Stains button again to come out of the Stains sub menu 24 Further extras m Press the Further extras button Select the Further extras you want Press the Further extras button again to come out of the Extras menu Extra quiet If using your machine during quiet periods you can reduce the noise levels even more The buzzer will not sound If the Extra quiet Extra option is selected the machine will activate the Rinse hold Extra option and not spin The programme duration is longer To deactivate Rinse hold m Press the Further extras button and use the V or A button to select Rinse hold To deactivate Rinse hold press the OK button The following will appear in the display i Delay start can be used to delay the spin Use Delay start to begin the final spin at a convenient time WASHING Extra rinse This Extra option introduces an extra rinse Pre wash For laundry
70. the Further extras button again to come out of the Extras menu You can only select Extra options which are compatible with the programme being used If the Extras or Stains option cannot be selected it is not compatible with the programme you are trying to use it with The Low temperature option is only available for a drying programme Load the drum m Press the Door button to open the drum door The load size indicator display will appear The display shows the amount of laundry loaded in the drum as a in 2596 steps of the maximum load permissible for the programme selected m Unfold the laundry and load loosely into the drum Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning The most efficient use of energy and water is achieved when a full load is washed However do not overload as this causes creases and reduces cleaning efficiency Make sure that no items are caught between the drum door and seal m Shut the door with a gentle swing 21 WASHING Q Add detergent The detergent dispenser display will now appear Detergent A uw 100 The percentage shown relates to the amount of detergent recommended by the manufacturer on the packaging 40 Add slightly less than half the recommended amount 50 Add half the recommended amount 60 Add slightly more than half the
71. the end of the programme items which have been treated with inflammable cleaning agents or which contain residues of acetone alcohol benzine petrol stain remover turpentine wax and wax remover or other chemicals e g mops and floor cloths items which have been splashed with hair lacquer hair spray nail varnish remover or similar Substances When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times P To prevent the risk of fire the following must not be dried in this washer dryer items which have been cleaned using chemicals e g professional dry cleaning agents fabrics which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling damaged items which contain padding or fillings e g pillows jackets When damaged the filling can get out with the risk of igniting in the washer dryer Warning and safety instructions P In many programmes the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The programme is not finished until the cooling down phase has been completed Ensure that you always wait
72. the safety standards of the machine be guaranteed P If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger P This washer dryer must not be installed and operated in mobile installations e g on a ship P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the machine and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the warranty P Do not make any alterations to the washer dryer unless authorised to do so by Miele Warning and safety instructions Correct use Caution Risk of fire To avoid the possible danger of fire please read these warnings carefully READ THE INSTRUCTIONS P The washer dryer is not suitable for outdoor use P Do not install your washer dryer in rooms where temperatures below freezing may occur Frozen hoses may burst or split The reliability of the electronic control unit may be impaired at temperatures below freezing point P Before using the washer dryer for the first time check that the transit bars at the rear of the machine have been removed see section on Installation During spinning a transit fitting which is still in place may result in damage to both the machine and adjacent furniture or appliances P Turn off the tap if the machine is t
73. the value or option highlighted in the display With the programme selector at the Further programmes Settings position you can change display settings see Settings menu and select the additional programmes see Programme chart The display is also used for selecting the wash temperature spin speed soak duration delay start safety lock and to cancel a programme Use This washer dryer can be used to wash separately Maximum load depending on programme 5 5 kg to dry separately Maximum load depending on programme 2 5 kg or to wash and dry in a continuous sequence Maximum load depending on programme 2 5 kg Before using for the first time Before using the machine for the first time ensure that it is correctly installed and connected Also check that the drain filter is securely tightened to prevent the risk of water leakage during use See Installation and connection This washer dryer has undergone a complete functional test at the factory and there will be some residual water in the drum from this process The washer dryer has a sensor which measures the amount of laundry in the drum This determines the amount of detergent required To allow the load size indicator to function correctly you must first run a wash programme without any laundry and without detergent m Turn on the tap m Press the button If the machine is being switched on for the first
74. then unscrew the threaded union connecting the free end of the inlet hose to the tap m Remove the rubber seal 1 from the recess m Hold the free end of the inlet hose upside down The plastic filter 2 will fall out m Clean the plastic filter m Replace the filter and seal and reconnect the hose Turn on the tap and check the connection is watertight If water leaks tighten the connection Never forget to put the filter back in place after cleaning 55 Problem solving guide With the help of the following notes minor faults in the performance of this machine some of which may result from incorrect operation can be put right without contacting Miele Please note that a call out charge will be applied for unnecessary service visits where the problem could have been rectified as described in these Operating instructions Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work The programme does not start Problem Possible cause Remedy The display remains dark and the programme selector is not lit up There is no power to the machine Check whether the mains plug is plugged in and switched on the fuse or circuit breaker has tri
75. ts Extras Thermospin Extra quiet Woollens Max load 1 0 kg 3 minutes Suitable for Wool and wool blend fabrics Note This programme only fluffs up woollen garments They are not dried completely by this programme Remove garments as soon as the programme has finished and leave to finish drying at room temperature Weight of dry laundry 41 DRYING Express 20 Max load 2 5 kg Extra dry Normal Normal Hand iron 4 Hand iron Machine iron Smoothing Timed drying Suitable for Fabrics which can tolerate high temperatures and which can be dried using the Cottons programme Note If washing and drying in one operation the programme duration will be particularly short with the Express 20 programme Extras Thermospin Extra quiet Shirts Max load 1 0 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Shirts and blouses Note Garments are dampened before the programme starts to help reduce creasing Automatic plus Max load 2 5 kg Normal Normal Hand iron Smoothing Timed drying Suitable for Mixed loads of garments suitable for the Cottons and Minimum iron programmes Extras Thermospin Extra quiet Freshen up Max load 1 0 kg Suitable for Freshly laundered and spun garments or dry garments that have been worn briefly and are not soiled Note
76. ut T L onee plus pressing V Pressing OK Y confirms the selection and changes m Select the drying programme you to the Thermospin speed option want Cottons The display will show the selected programme Hormal Duration attoanz m You can change the highlighted spin speed by pressing V or A Duration zh Thermospin is not activated if a Further programmes drying time is selected After selecting Further m Select Low temperature if desired programmes Settings other m Select Extra quiet via the Further programmes will appear in the display extras button if desired Further programmes a i E Thermospin is not activated if Low temperature is selected Dark garments m f required select a Delay start time m Highlight the required programme with V or and confirm with OK m Press Washing Drying button repeatealy until only the Drying indicator light is lit up 37 DRYING Load the washer dryer m Open the drum door m Load the laundry loosely into the drum Do not overload the drum See the drying Programme chart for recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result Close the door Make sure that no garments are caught between the drum door and seal Make sure that objects e g detergent dispensing balls have been removed from the laundry They could melt
77. will drain away and the machine will go straight into the anti crease stage With some programmes an additional rinse is introduced if this setting is selected WASHING Programme chart Cottons 5 76 Gs 0 aa Ga cold to 90 C Max load 5 5 kg Suitable for Cotton linen or cotton mix fabrics e g T shirts underwear table linen Extra options Short Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold Note for test institutes Short programme 3 kg load and Short Extra option Minimum iron EJ EJ 5 Sa eo Ba C35 30 cold to 60 C Max load 3 0 kg Suitable for Synthetics and mixed fibre garments as well as easy care cottons Extra options Short Water plus Stains Extra quiet Extra rinse Pre wash Soak Rinse hold Denim cold to 60 C Max load 3 0 kg Notes Wash denim inside out Denim often contains excess dye and may run during the first few washes Wash light and dark coloured items separately Extra options Short Stains Extra quiet Pre wash Soak Rinse hold Woollens W ao Ba cold to 40 C Max load 2 0 kg Suitable for Machine and hand washable wool or wool blend garments If the care label does not specify a temperature wash using the cold setting Extra options Rinse hold Express 20 40 0 cold to 40 C Max load 3 0 kg Suitable for Small loads of lightly so
78. wing order 1 Detergent 2 Water softeners 3 Stain remover This way the agents are distributed more evenly WASHING Fabric conditioner and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying Starch stiffens and gives body to items of laundry e g shirts tablecloths and bed linen Automatic dispensing of fabric conditioner or liquid starch to laundry at the end of a programme m Add the fabric conditioner or liquid starch to compartment amp Do not exceed the maximum level mark It will be dispensed automatically in the last rinse At the end of the programme a small amount of water remains in the fabric conditioner compartment amp If starching frequently thoroughly clean the dispenser compartment especially the siphon tube and fabric conditioner channel regularly See Cleaning the detergent dispenser drawer Do not use powder starch formulations or viscous liquid starch in the amp compartment as it will clog up See below Adding fabric conditioner or liquid starch separately m Dispense in accordance with manufacturer s instructions on the packaging m Dispense liquids into the amp 9 compartment and powder or viscous formulations into the LU compartment m Turn the programme selector to Further programmes Settings and select the Starch programme m Select a spin speed or the Hinse hold Extra option m Press the St
79. with large amounts of dirt e g dust sand Soak For heavily soiled items with protein stains A length of time of between 30 minutes and 6 hours can be chosen in 30 minute periods for the Soak process Soak duration D 30 hmin 0 00 6 00 h m Use the V or A button to highlight the Soak duration you wish to use and confirm your selection by pressing the OK button To delete the soak duration m Press the Further extras button and use the V or A button to select Soak To deactivate Soak press the OK button Rinse hold The laundry will not be spun and will remain suspended in the final rinse water This reduces creasing if the laundry is not going to be removed from the drum immediately after the end of the programme Adding or removing laundry after a programme has started m Press the Door button to open the drum door m Add or remove items m Close the drum door The programme will continue automatically Please note Once a programme has started the machine cannot recognise any adjustment to the load For this reason if laundry is added or removed after the start of a programme the machine will always complete the programme cycle assuming a full load This can alter the programme running time shown in the display The door cannot be opened if the suds temperature is above 55 C the water is above a certain level the programme has reached the Final spin stage t

Operating instructions Washer-dryer WT 2780 WPM

Contents

Download Pdf Manuals

Related Search

Related Contents