OPERATING INSTRUCTIONS FOR THE
Contents
1. NOTE 2 For automatic totalising enter Func 17 select hold amp add using the UP DOWN keys then press LOAD to save selection This allows automatic adding of the weight to the total as it is weighed FUNC 17 allows the lift sensor to preform tasks as follows a HOLD amp ADD Weight is held on display for a pre determined period Weight is automatically added into the TOTAL display b HOLDS ONLY Weight is held on display for a pre determined period Weight can be added into TOTAL display with LOAD key c DOES NOTHING No action from lift sensor Use UP DOWN keys to scroll through options Press LOAD to save selection NOTE 3 Press UNDO within the eight seconds to deduct the last added weight from the total NOTE 4 Func 14 allows operator to enter target weight to load onto truck Compuload will show enter alarm weight Use key pad to enter truck capacity 0 00 turns target weight alarm off Press LOAD to save setting NOTE 4 Whilst the Compuload 4000 is designed to weigh loads as the machine is operated and the load is lifted some conditions may cause variations to the weight readings Results can generally be improved by using care whilst weighing D Lift the load at a smooth speed through the lift sensor Do not stop the lift cycle until a weight reading is obtained ID Open lifting valve fully to raise the load ID Whilst weighing have loader on a level surface IV Avoid bounce on rough surfaces whilst weighing V2. 4000 8 WARRANTY COMPULOAD 4000 THE COMPULOAD 4000 HAS NO USER SERVICEABLE COMPONENTS INSIDE DO NOT ATTEMPT TO DISMANTLE THE UNIT AS THIS WILL CAUSE YOUR WARRANTY TO BECOME NULL AND VOID ATLAS WEIGHING Pty Ltd warrants the COMPULOAD Series 4000 load weighing gauge and any optional equipment to be free of defects in workmanship and material for a period of twelve 12 months from date of dispatch or installation whichever is applicable This Warranty only applies provided the COMPULOAD 4000 and accessories are used in accordance with the recommendations of ATLAS WEIGHING Pty Ltd under normal use and reasonable care The warranty does not cover damage in any way whatsoever including transit damage The warranty does not cover malfunction or failure resulting from misuse neglect or abuse The warranty immediately becomes void should any repairs alterations or modifications are carried out or attempted to be carried out by other than ATLAS WEIGHING Pty Ltd The warranty is not transferable and applies only to the original purchaser unless authorised by ATLAS WEIGHING Pty Ltd The warranty does not include travel expenses should a factory engineer or representative be required to preform repairs on site At the option of ATLAS WEIGHING Pty Ltd any faulty units or components will be repaired or replaced free of charge whilst within the warranty period providing the unit or component is returned to our premises with freight pre
3. Regularly check the zero regularly Compuload 4000 3 STORING OF DATA INTO THE COMPULOAD 4000 The Compuload 4000 has three fields into which data can be stored The factory defaults are customer product truck These fields can be altered to suit your application however for this exercise we will use these field names This software version also has the option for Code protected Fields to protect unauthorised deleting of entered Fields Contact your supplier for more information To store into these fields enter FUNC 11 Compuload will show enter customer 1 To select a previously entered customer Key in the number of the required customer Press LOAD If selection is correct press LOAD again If selection is incorrect key in correct number and press LOAD again To enter a new customer Select a vacant customer number Press CLEAR key Enter a new customer with key pad Press LOAD Compuload will show FUNC 12 enter product 1 To select a previously entered product Key in the number of the required product Press LOAD If selection is correct press LOAD again If selection is incorrect key in correct number and press LOAD again To enter a new product Select a vacant product number Press CLEAR key Enter a new product with key pad Press LOAD Compuload will show FUNC 13 enter truck 1 To select a previously entered truck Key in the number of the required truck Press LOAD If selection is correct press LOAD again If s
4. E FIELDS Allows data entered in Func 11 12 amp 13 to be erased The display is temperature sensitive Display contrast is adjustable use the UP key to lighten Use the DOWN key to darken Compuload must have completed power up cycle Should screen go black press UP key Should screen not display characters blank out press DOWN key Compuload 4000 6 CODE PROTECTED OPTIONS Requires a code to be entered to allow access FUNC 18 FUNC 19 FUNC 20 FUNC 21 FUNC 22 FUNC 75 FUNC 76 Compuload 4000 FINE ADJUSTMENT OF SPAN Allows fine adjustment of accuracy of weighing system Can be increased or decreased by a percentage as required Use CLEAR to select or then enter the percentage to be adjusted Press LOAD to save adjustment SET CHANNEL Allows channel to be changed to allow the COMPULOAD 4000 to be changed to another machine or weigh in a different method Key in channel number 1 or 2 Press LOAD to save selection SET TIME Allows time clock to be reset Use UP DOWN amp LEFT RIGHT keys to set Press LOAD to save alteration SET DATE Allows date to be reset Use UP DOWN LEFT RIGHT keys to set Press LOAD to save new setting SET OVERLOAD ABOVE TOTAL Allows the truck target total to be exceeded by a percentage amount Key in percentage Press LOAD to save setting PRINTER HEADER 1 Allows the printer header line 1 to be altered Key in required text for line 1 of the printer header Press LOAD to sa
5. OPERATING INSTRUCTIONS FOR THE COMPULOAD 4000 series LOAD WEIGHING SYSTEM and 4060 PRINTER Software Version C L4v4 31 37 No Weighing Message Version Postal Address ATLAS WEIGHING Pty Ltd P O Box 3192 ROUSE HILL NSW 2155 Deliveries 11 322 Annangrove Road ROUSE HILL NSW 2154 Tel 02 9679 0045 Fax 02 9679 0048 International Ph 61 2 9679 0045 Fax 61 2 9679 0048 Compuload 4000 PAGE Compuload 4000 INDEX ITEM COVERED BASIC WEIGHING lift speed compensated method STORING OF DATA RECOVERY OF STORED DATA OPTIONS AVAILABLE operator accessible OPTIONS AVAILABLE code protected USB INSTRUCTIONS WARRANTY BASIC WEIGHING AND TOTALISING lift speed compensated method NOTE 1 When first turned on a message will appear showing Zero Required In this instance proceed as in la below 13 With the bucket empty and fully crowded raise up through the lift sensor switch at a normal lifting speed If other than 0 00 zero is displayed press ZERO for two seconds to zero display 2 Apply the load and raise up through the lift sensor switch The weight will be displayed for a pre determined period usually 8 12 seconds Do not stop the lift until the display shows HELD 3k Press LOAD to add weight into the total display 4 Press CLEAR for two seconds when required total is reached This returns TOTAL display to 0 00 and allows data to be stored if applicable see storing data
6. ds to the next function Pressing CLEAR exits the function without altering the setting USER ACCESSIBLE OPTIONS FUNC 01 FUNC 02 FUNC 03 FUNC 04 FUNC 05 FUNC 06 FUNC 60 NOTE SET TARE Not normally used on loaders Allows a pre set tare to be entered and deducted from the actual weight Pressing the key causes the display to toggle between the actual weight and the nett weight Use key pad to enter required tare Press LOAD PRINTER STATE Turns external printer if fitted ON OFF COPY Use UP DOWN keys to select Press LOAD NOTE When set to COPY the option to print out a copy of the load is offered for a limited time Press LOAD to obtain a copy Press CLEAR to exit DATA LOG PRINT OPTIONS Allows stored data logs to be printed Select number of days and press LOAD Other options allows the loads for a particular customer product or truck to be printed Press UP DOWN key to select the particular field then key in field number with keypad Press LOAD ERASE DATA LOGS Deletes the data logs Once erased the logs cannot be retrieved DISPLAY TOTALS Long Totals Allows individual customer product truck totals to be viewed Use UP DOWN keys to select field then select field number with keypad Press LOAD This is reset with Func 04 VIEW TOTALS Allows Grand total to be viewed if required For customer Totals see Func 05 This is reset with Func 04 ERAS
7. election is incorrect key in correct number and press LOAD again To enter a new truck Select a vacant truck number Press CLEAR key Enter a new truck with key pad Press LOAD Compuload will show FUNC 14 set alarm weight Use key pad to enter target weight to load onto truck 0 00 turns target weight alarm off Press LOAD to save setting NOTE The Compuload will remember the target weight for each truck Compuload 4000 4 RECOVERY OF STORED DATA and PRINTOUT OPTIONS Data stored in the memory of the COMPULOAD 4000 can be recovered and handled in the following manner PRINTOUT FUNC 03 COMPULOAD 4000 will display Print Logs Last Press LOAD COMPULOAD 4000 will display Number of days soy If only today s logs are required press LOAD If more than one days logs are required enter number of days with keypad and press LOAD RESETTING THE DATA LOGGER FUNC 04 COMPULOAD 4000 will display Erase data logs No Press UP key Compuload will display Erase data logs Ves Press LOAD All records will be erased P C DOWNLOAD optional Windows 98 or later with optional PC download kit Downloads stored logs to ascii file Logs can be imported to spreadsheet Compuload 4000 5 OPTIONS AVAILABLE The following options are available to the operator if required and as required They are entered by pressing FUNC key and the corresponding number pressing LOAD saves the setting and procee
8. paid Our factory engineers will offer all possible assistance to rectify any difficulties experienced in the field The larger majority of problems can be overcome by telephone Please contact our office prior to forwarding any units or components for attention NOTE Our carrier does not accept responsibility for loss or damage in transit Should transit or freight loss or damage insurance be required it must be indicated on your order and the cost of such insurance will be charged accordingly Compuload 4000 9
9. ve new header PRINTER HEADER 2 Allows the printer header line 2 to be altered Key in required text for line 2 of the printer header Press LOAD to save new header DOWN LOAD TO USB To enable the COMPULOAD USB DOWNLOADER if fitted Enter FUNC 79 Scale will show enter code Enter the low security code then press LOAD Scale will then show on the top line USB INTERFACE On the bottom line it will show ON or OFF Use the up or down keys to change the setting to ON Press LOAD NOTE The Compuload USB Function will remain in the ON position until it is turned OFF using the same process Scale will return to the normal weighing mode Simply insert the COMPULOAD USB STICK into the COMPULOAD USB DOWNLOADER Scale will acknowledge the stick with the message USB DETECTED and the green light on the COMPULOAD USB DOWNLOADER should stay illuminated Scale will then display USB DOWNLOAD on the top line and LAST on the bottom line of the display Use the up or down keys to change between LAST or ALL By selecting LAST and pressing LOAD you will then be asked how many days you wish to download Select the number of days that you wish to download then press LOAD The scale will indicate when it is safe to remove the USB stick By selecting ALL the Compuload will download all data stored since the log has been reset Compuload
Download Pdf Manuals
Related Search