Home

AIRCRAFT OPERATING INSTRUCTIONS Light

1. 4 12 12 Remove Main Sail Battens Pull the leading edges together approximately 1 2 metre Remove the remaining main sail battens Insert battens in the batten bag NOTE The straight battens are inserted in separate pockets Figure 69 Section 4 Remove Main Sail Battens 4 12 13 Fold Leading Edges Fold both wings in symmetrically bringing both leading edges back at the same time or in small steps side to side Roll the sail inwards parallel to the leading edge Attach a strap around one wing Repeat for the other side Fit the keel end pouch Figure 70 Section 4 Fold Leading Edges 4 12 14 Attach Straps Once the leading edges are together apply slight pressure downwards on the keel to raise the leading edges above the down tubes and attach strap around both wings and keel Ensure the nose wire is disconnected before pushing down on the keel Attach remaining straps so that they are evenly spaced 4 12 15 Fit Wing Bag Position the wing bag to the nose of the wing Stretch bag down the wing to enclose the tips 4 12 16 Roll Wing Hold the wing and down tube and roll the wing onto its back with the control frame to the side 4 12 17 Disconnect Base Bar Depress pip pin button and remove pip pin from base bar Fold down tubes together with base bar folded out Re insert the pip pin Figure 71 Section 4 Disconnect Base Bar August 2009 Issue 2 2 Page 49 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating
2. Use wheel chocks when leaving the disk brake equipped aircraft unattended for a period of time August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 14 Electrical System An electrical schematic for the aircraft is shown in the diagram on the following page The Electrical circuits comprise e an instrumentation circuit The 12 V DC supply is protected by a 20 amp fuse at the battery and a 10 amp circuit breaker mounted on the dash The master switch on the dash when in the off position disables the DC power socket flight instrument and the electric start push button e anengine management circuit and e anignition circuit It should be noted that the ignition circuit is a fail safe system whereby the engine will run in the event of the ignition circuit becoming disconnected Switching the coil to ground stops the engine When stopping the engine both switches on the side of the seat should be switched off The master switch on the dash should then be turned to the off position to remove supply to the accessories If necessary the motor can be stopped using the chokes as detailed in section 3 3 10 of this AOI Refer to the Rotax manual for more details for the engine electrical system August 2009 Issue 2 2 Page 6 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 14 1 X
3. 1 1 2 Definitions Definitions used in the Aircraft Operating Instructions such as WARNING CAUTION and NOTE are employed in the following context WARNING OPERATING PROCEDURES TECHNIQUES ETC WHICH IF NOT FOLLOWED CORRECTLY MAY RESULT IN PERSONAL INJURY OR DEATH CAUTION OPERATING PROCEDURES TECHNIQUES ETC WHICH IF NOT STRICTLY OBSERVED MAY RESULT IN DAMAGE TO THE AIRCRAFT OR ITS INSTALLED EQUIPMENT NOTE Operating procedures techniques etc which it is considered essential to highlight August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 2 General Description 1 1 3 Two View Photos XT 912 Streak shown in photographs TT NND m me y i EIN Figure 2 Section 1 Aircraft Side View August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 1 1 4 General Dimensions 1 1 4 1 XT 912 Streak DIMENSIONS Wing Span Wing Area Aspect Ratio Wing Weight Overall Height Control Bar Fwd Trike Width Trike Length Wheel Track Wheel Base Trike Height Cockpit Width Wing Packed Length Wing Length Short Packed Table 1 Section 1 General Dimensions Streak 3 1 1 4 2 XT 912 SST DIMENSIONS Wing Span Wing Area Aspect Ratio Wing Weight Overall Height Control Bar Fwd Trike Width Trike Length Wheel Track Wh
4. 58 kg Streak 3 50 kg Cruze 51 kg and Merlin 49 kg Aircraft Type AirBorne WindSports EDGE XT 912 STREAK CRUZE MERLIN serial No Issue Date Empty Weight kg Trike Base XT912 1 kg Unusable Fuel 3 Litres 1 2 kg Wing 1 kg Training Bars 1 4 kg If applicable 1 Issue 1 Aircraft Empty Weight kg Trike Base XT912 2 kg Unusable Fuel 3 Litres 2 2 kg Wing 2 kg Training Bars 1 4 kg 2 If applicable Issue 2 Aircraft Empty Weight kg Table 1 Section 6 Aircraft Weight Empty Weight for the aircraft comprises of e Standard equipment as per section 6 2 2 e Optional equipment as per section 6 2 3 e Full coolant full engine oil and unusable fuel The keel extension and pack up gear are not included in the empty weight August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 6 2 2 Standard Equipment STANDARD EQUIPMENT Fitted Yes No Engine Type ROTAX 912 UL2 Engine Serial Number Carburettor Heating Std Airspeed Indicator Knots Sid GX2 Instrument otd Tool Kit amp Mast Strap Hold Down Strap otd Table 2 Section 6 Aircraft Weight Standard Equipment 6 2 3 Alternate Equipment Fitted Yes No ALTERNATE EQUIPMENT Gear Type 2 27 1 Gear 2 43 1 Propeller Type BOLLY BOS 66 INCH with BOS 3 hub Propeller Type Warp Drive 3 67 7 INCH Blade with Warp Drive hub Table 3 Section 6 Aircraft Alternate Equipment 6 2 4 Optional
5. Figure 44 Section 4 Remove Undersurface Battens 4 11 5 Fit Tip Bags Roll sail at the tips inwards and parallel to the leading edge Slide the tip bag over the end of the leading edge The barrel lock unit can be used to tension the bag bungee Figure 45 Section 4 Fit Tip Bags 4 11 6 Fit U Bracket Cover Unzip undersurface approximately 1 metre to allow better access to fit the U bracket cover Pass the cover up over the keel with the webbing strap facing to the rear of the wing Locate on hook and loop fasteners around each down tube photo shown is a rear view Figure 46 Section 4 Fit U Bracket Cover August 2009 Issue 2 2 Page 40 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 7 Velcro U Bracket Face Cover Position the face cover so that it is facing forward The cover is designed to protect the wing bag when packed photo shown is a front view Figure 47 Section 4 Velcro U Bracket Face Cover 4 11 8 Trimmer Cover If applicable position the trimmer handle so that the handle is at 90 degrees to the down tube with the knob facing forward Fit the trimmer cover Figure 48 Section 4 Trimmer Cover 4 11 9 Disconnect Nose Catch and Remove Nose Cone Remove the nose cone Disconnect nose catch by removing the pip pin The pip pin button should be depressed with the thumb while simultaneously pulling the pip pin out Re insert pip pin in nose
6. side below the engine Metric or imperial placard required Series Edge XT 912 Series Table 20 Section 2 Tank Oil Capacity Placard 2 7 17 No Step Placard 55mm NO 42mm E P No 105718 Location The step placards are located on the floor of the cockpit either side of the base tube Series Edge XT Series Table 21 Section 2 No Step Placard August 2009 Issue 2 2 Page 17 SECTION 2 AirBorne WindSports Pty Ltd LIMITATIONS Aircraft Operating Instructions Edge XT 912 2 7 18 Step Placard 30mm 30mm 5 105712 The step placard is on the trike base tube at the hinge point for the rear foot rest Edge XT Series Location Series Table 22 Section 2 Step Placard 2 7 19 Step and No Step Placards Figure 6 Section 2 Step and No Step Placards NOTE There is a symmetrical No Step Placard on the other side of the Pod August 2009 Issue 2 2 Page 18 SECTION 2 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 20 Clear Prop Placard 120mm CLEAR PROP PART No 105716 18mm Location The clear prop placard is located on the right and left side compression struts Series Edge XT Series Table 23 Section 2 Clear Prop Placard 2 7 21 Shock Absorber Pressure Placard dcm CAUTION P No 106397 Location The shock placard is located on the main block near the top of the shock Series Edge XT Series Table 24 Sect
7. 5 Section 5 Cruze Landing 5 2 6 Landing XT 912 Merlin Performance at MTOW Metric Imperial Landing Distance from 15 m 50 ft 306m 1004 ft Table 6 Section 5 Merlin Landing Landing distances are specified for Sea Level with A level dry runway With short grass Still wind And temperature of 15 deg C The following factors will increase landing distance Lower drag runway surfaces such as tarmac Tail wind Down hill landing OAT above 15 deg C Runway altitude above sea level The pilot is required to take into account the effect of the above when determining landing distance Crosswind components of up to 12 knots at maximum AUW are within aircraft operating limitations Always exercise judgement when selecting locations for take off and landing Leave adequate CAUTION margin for appropriate control action in the event of TAKE OFF AND LANDING DISTANCES MUST sudden engine failure or turbulence being BE INCREASED BY 20 FOR EACH 1000 encountered FEET OF ALTITUDE ABOVE SEA LEVEL August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 5 Aircraft Operating Instructions Edge XT 912 PERFORMANCE 5 3 Climb 5 3 1 XT 912 Streak and SST Performance at MTOW Metric Imperial Climb rate 49 kts 4 2 m sec 825 ft min Best Climb Speed 49 kts 49 kts oea Level Gradient of Climb 17 896 17 896 Table 7 Section 5 Streak and SST Climb 5 3 2 XT 912 Cruze Performance at MTOW Metric Imperial Climb rate 45 kts 5 0
8. CYLINDER HEAD TEMPERATURE Maximum 150 deg C 300 deg F EXHAUST GAS TEMPERATURE Maximum at Max TO power 880 Deg C 1620 deg F Maximum at Max Continuous Power 850 Deg C 1560 deg F Normal Temperature 800 Deg C 1472 deg F AMBIENT START amp OPERATING TEMPERATURE Maximum 47 deg C 116 deg F Minimum 25 deg C 13deg F Maximum at Max Continuous Power 800 Deg C 1472 deg F Table 3 Section 2 Engine Limitations NOTE Minimum oil temperature of 50 deg C should be reached before take off Operate for 2 min at 2000 rpm continue at 2500 rpm until minimum temperature is reached August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 4 3 Fuel Grades FUEL En228 Premium Regular Super grade gasoline lead free min RON 90 Optional Fuel Type AVGAS see note Preferred Fuel Type Table 4 Section 2 Fuel Specification NOTE Due to higher lead content in AVGAS the wear of the valve seats and deposits in the combustion chamber will increase Therefore use AVGAS only if you encounter problems with vapour lock or if the other fuel type is not available Use of AVGAS requires higher frequency maintenance intervals Refer to the maintenance manual Refer to section 2 6 7 for fuel capacities and limitations 2 4 4 Lubricating Oil The 912 UL engine has an external sump and the entire system is standard to the Rotax 912 engine The oil specification is given in the Rotax O
9. Instructions Edge XT912 NORMAL PROCEDURES August 2009 Issue 2 2 Page 50 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 12 18 Fit Padding Fit the base bar and down tube covers Velcro the base bar cover in whilst holding the base bar in position Figure 72 Section 4 Fit Padding 4 12 19 Fold Control Frame Undo centre two wing straps Route flying wires between the down tube and lower the control frame into the wing whilst holding tension on wires Avoid kinking the flying wires 4 12 20 Position Battens Stow the battens with the curve down at the rear of the glider bag Reattach wing straps so that the control frame and battens are within the leading edge pockets Zip up the wing bag Figure 73 Section 4 Position Battens 4 12 21 Position Struts August 2009 Issue 2 2 Page 51 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Figure 74 Section 4 Fit Padding August 2009 Issue 2 2 Page 52 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 13 Transportation and Storage The wing must always be transported inside its bag and the bag zip should face downwards to prevent the entry of rainwater During transportation or when stored on slings the wing must be supported at its centre and at two points not more than one metre from each end The padding
10. Normal Operation 5 4 1 5 Normal procedures Checklist 5 4 2 Wing Assembly Procedure Streak 3 Cruze and Merlin 6 4 2 4 Unzip Wing Bag 6 4 2 2 Assemble Control Frame 7 4 2 3 Stand The Wing Up 8 4 2 4 Spread Leading Edges 8 4 2 5 Insert King Post 8 4 2 0 X Insert Main Sail Battens 8 427 Tension Cross Bars 9 4 2 8 Install Pull Back Cover 9 4 2 9 Attach Nose Catch 9 4 2 10 Locate Nose Battens 9 4 2 11 Install Nose Fairing 10 4 2 12 Insert Remaining Main Sail Battens 10 4 2 13 Insert Undersurface Battens 10 4 2 14 Load Tip Strut Clip Type 10 4 2 15 Load Tip Strut Hinge Type 11 4 3 Wing Assembly Procedure SST 12 4 3 1 Unzip Wing Bag 12 4 3 2 Assemble Control Frame 12 4 3 38 Stand The Wing Up 12 4 3 4 Spread Leading Edges 12 4 3 5 Connect Control Frame To Wing Struts 13 4 3 6 Connect Strut at Leading Edge 13 4 3 7 Insert Main Sail Battens 13 4 3 8 Tension Cross Bars 14 4 3 9 Attach Nose Catch 14 4 3 10 Locate Nose Battens 14 4 3 11 Install Nose Fairing 15 4 3 12 Place U Bracket Padding Inside Sail 15 4 3 13 Insert Remaining Main Sail Battens 15 4 3 14 Insert Undersurface Battens 15 4 3 15 Inboard And Outboard Sprogs 16 4 3 16 Load Tip Over Centre Battens 16 4 4 Wing Pre flight inspection 18 4 5 Attaching Wing to Base 19 4 5 1 Attach Mast Retaining Strap 19 4 5 2 Position The Trike And Wing 21 4 5 3 Attach Mast Wing U Bracket 21 4 5 4 Position Heart Bolt Retainer in U Bracket 21 4 5 5 Attach Back Up
11. Range 9 Cruise Australian 70 kts 11 It hr 730 km Australian 65 kts 12 It hr 670 km Australian 50 kts 9 5 t hr 650 km Table 19 Section 5 Cruze Cruise Performance 5 7 4 XT 912 Merlin Performance at MTOW Cruise Speed Typical Fuel Burn Cruise See Note Range 9 Cruise Australian 47 kts 9 5 t hr 613 km Table 20 Section 5 Merlin Cruise Performance NOTE Fuel consumption figures are included as a guide only The consumption figures should not be used for planning purposes Changes in aircraft configuration load altitude wind strength and direction as well as European 130 km hr 11 It hr 730 km European 120 km hr 12 It hr 670 km European 92 km hr 9 5 t hr 650 km European 87 km hr 9 5 It hr 613 km climatic conditions will cause significant variation in fuel consumption August 2009 Issue 2 2 SECTION 5 PERFORMANCE USA 80 mph 2 9 gal hr 453 miles USA 75 mph 3 2 gal hr 416 miles USA 5 mph 2 5 gal hr 403 miles USA 54 mph 2 5 gal hr 381 miles Page 6 AirBorne WindSports Pty Ltd SECTION 6 Aircraft Operating Instructions Edge XT 912 WEIGHT BAL amp EQUIP WEIGHT BALANCE AND EQUIPMENT WEIGHT BALANCE AND EQUIPMENT 6 WEIGHT BALANCE AND EQUIPMENT 6 1 General 6 2 Aircraft Weight 6 2 1 Aircraft Weighing Information 6 2 2 Standard Equipment 6 2 3 Alternate Equipment 6 2 4 Optional Equipment 6 3 Typical Aircraft Weights 6 3 1 Weighing Procedure 6 3
12. SECTION 4 NORMAL PROCEDURES WARNING NEVER STALL THE AIRCRAFT WITH THE NOSE PITCHED UP BEYOND 45 DEGREES MANOEUVRES BEYOND THIS ARE DANGEROUS AND CAN RESULT IN A TAIL SLIDE FOLLOWED BY A SEVERE TUMBLE away suddenly A stall would have to be forced violently to induce a danger REFER TO SECTION 3 3 12 OF THIS FLIGHT MANUAL FOR DETAILS OF THE PROCEDURES FOR RECOVERY FROM UNUSUAL ATTITUDES When practising stalls make sure you have sufficient altitude Push the control bar out so that the airspeed is reduced at a maximum of 1 knot per second and the aircraft will reach a minimum steady flight speed without dropping a wing The sink rate will increase in this minimum speed mode more than two fold If the airspeed is decreased by rapidly raising the nose the wing will stall Rapid decrease of airspeed in the order of 2 3 knots per second will see an altitude loss of up to 100ft See section 3 3 12 for recovery procedures Never stall with the nose pitched up too high This is a dangerous manoeuvre and can result in a tail slide followed by a severe tumble As a guideline the nose up angle at which the aircraft stalls is about the nose down angle it will recover at 4 9 18 Descent Approach and Landing Landing should always be into wind with a long straight approach The landing distance specified in Section 5 is the measured ground distance covered from an approach at 50 feet above the average elevation of the runway used unt
13. Still wind And temperature of 15 deg C Take off Landing 247m 810 and 247m 810 and 210m 689 and 204m 669 and distance over 50 325m 1066 325m 1066 306m 1004 306m 1004 obstacle respectively respectively respectively respectively Stall at 450kg 35 kt 40mph 35 kt 40mph 34 kt 39mph 33 5 kt 38 5mph MTOW MTOW 27 7 kt 312kq 15 15 14 14 4 Average Fuel Burn 11 It hr 2 9 gph 12 It hr 3 2 gph 9 5 It hr 2 5 gph 9 5 It hr 2 5 gph at Cruise Take off from a level grass surface at 1 4 x stall speed and climb to 50 ft with a 1 3 safety factor Landing with front drum brake only 9 11 Training Recommendations The XT 912 handles predictably in all flight regimes so there are no unique training requirements in any area except landing Like all WSC aircraft aerobatic maneuvers are strictly prohibited 9 11 1 Landing Most WSC pilots are unprepared for the speed of the XT 912 s approach to landing As previously stated it is not necessary to pull the control bar in past the trim position unless a considerable amount of turbulence is encountered Fly the final approach at trim speed and flare normally You will notice that the approach is also flatter than most WSC aircraft allowing for a smoother less abrupt flare out to land Merlin approach speeds may be made at trim speed where trim speed is 45 kt and greater August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operatin
14. Taxiing Taxiing in normal conditions is fairly straight forward With the engine idling the brake lever should be depressed which will disengage the park brake The control frame should be positioned so that it is in the approximate position for normal trim speed The pilots feet actuate steering on the ground Left turn occurs when the right footrest is pushed forward Right turn occurs when the left footrest is pushed forward NOTE Control sense for turning is opposite to that of a conventional three axis aircraft When taxiing in strong wind conditions the following procedures apply e Head Wind conditions requires the nose of the wing to be lowered just below the trim position Down Wind conditions requires the nose of the wing to be raised just above the trim position e Cross wind conditions requires the upwind tip to be lowered 4 9 13 Before take off Before flight a full throttle check is to be carried out During this operation the pilot must be seated in the cockpit and prepared to switch off the ignition at very short notice if an emergency should arise CAUTION BEWARE OF LOOSE STONES IN THE RUN UP AREA LOOSE STONES CAN BE SUCKED UP BY THE PROPELLER AND CAUSE SEVERE PROPELLER DAMAGE IN A VERY SHORT TIME RUN UPS ARE BEST CONDUCTED ON A CLEAR SEALED SURFACE OR ON GRASS NEVER ON GRAVEL The two ignition circuits should be tested with the engine running at 4000 rpm Ignition one should be switched off and the RPM drop should n
15. The Cruze wing was developed as an intermediate wing with lower stall speed and lower top speed Additional sail area has been added to the tip of the wing with a reduction in the sail luff curve The result of the XT 912 coupled with the Cruze is a very stable wing with a softer feel than that of the Streak wing The Cruze wing is a good all round wing with lower top speed than the Streak 3 The stall speed is also lower with shorter take off and landing distance required 1 1 5 5 XT 912 Merlin The Merlin wing was developed to expand the low speed performance capability of the XT microlight At high wing loadings the take off landing and stall speed performance is improved over that of the Cruze wing however at lighter wing loadings the Merlin truly excels The Merlin is a superb slow speed wing with wide speed range a lower top speed than the Cruze wing and maintains cross country flying capability The slow speed allows for landing the Tundra and Outback version trikes on soft sandy terrain or unprepared landing fields The Merlin wing is ideal for aerotowing hang gliders or towing advertising banners The Merlin has a high camber sail with higher aspect ratio and reduced sail area in comparison to the Cruze It is a highly manoeuvrable wing with a slow gentle stall The Merlin has a steady feel in turbulent air expanding the range of conditions that it is comfortable to fly in 1 1 5 6 XT 912 SST The SST wing is a high performance f
16. WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES This page left blank intentionally August 2009 Issue 2 2 Page 54 AirBorne WindSports Pty Ltd SECTION 5 Aircraft Operating Instructions Edge XT 912 PERFORMANCE PERFORMANCE PERFORMANCE 5 PERFORMANCE 5 1 General 5 2 Take Off and Landing 5 2 1 Take Off XT 912 Streak amp SST 5 2 2 Take Off XT 912 Cruze 5 23 Off XT 912 Merlin 5 2 4 Landing XT 912 Streak and SST 5 2 5 Landing XT 912 Cruze 5 2 6 Landing XT 912 Merlin 5 3 Climb 5 3 1 XT 912 Streak and SST 5 3 2 XT 912 Cruze 5 3 3 XT 912 Merlin 5 4 Airspeed Calibration 5 5 Stall Speeds 5 5 1 XT 912 Streak and SST 5 5 2 XT 912 Cruze 5 5 3 XT 912 Merlin 5 6 Glide ee ee 5 6 1 XT 912 Streak and SST 5 6 2 XT 912 Cruze 5 6 3 XT 912 Merlin 5 7 Cruise Performance 5 7 1 XT912 SST 5 7 2 XT 912 Streak 5 7 3 XT 912 Cruze 5 7 4 XT 912 Merlin AAAA aang A AAA A N N a August 2009 Issue 2 2 1 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 5 PERFORMANCE 5 1 General SECTION 5 PERFORMANCE The performance data in the following section has been computed from actual flight tests with the aircraft and power plant in good condition and using average piloting techniques It should be noted that piloting techniques climatic conditions and aircraft condition will cause s
17. beading of water BE REMOVED PRIOR TO TAKE OFF droplets can significantly increase the stall speed August 2009 Issue 2 2 Page 8 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 Placards The placards on the aircraft are designed to provide information regarding general aircraft limitations and other details for the safe operation of the aircraft Listed on the following pages are details of the placards fitted to the aircraft 2 7 1 Flight Limitations Placard 62mm 62mm ENGINE LIMITATIONS ENGINE MAX ROTAX 912 UL RPM EGT 5 MINUTES MAX 5800 rpm 1620 Deg F CONTINUOUS 1560 Deg F MIN ENGINE LIMITATIONS MAX ROTAX 912 UL RPM 5 MINUTES MAX 5800 rpm 880 Deg C CONTINUOUS 5500 rpm 850 Deg C MIN MAX OIL TEMPERATURE 50 Deg C 140 Deg C CYLINDER HEAD TEMP 150 Deg C FUEL TANK CAPACITY 70 Litres USEABLE FUEL 67 Litres LOADING LIMITATIONS SEE AIRCRAFT OPERATING INSTRUCTIONS SECT 6 3 3 FOR FUEL LOAD LIMITATIONS EMPTY WEIGHT MEME MAX TAKEOFF WEIGHT 450kg MIN MAX OCCUPANTS 55kg 200kg FLY SOLO FROM FRONT SEAT ONLY PART No 107599 OIL PRESSURE MAX 120 Deg F 285 Deg F CYLINDER HEAD TEMP 300 Deg F FUEL TANK CAPACITY 18 5 USGal USEABLE FUEL 17 7 USGal LOADING LIMITATIONS SEE AIRCRAFT OPERATING INSTRUCTIONS SECT 6 3 4 FOR FUEL LOAD LIMITATIONS EMPTY WEIGHT BEEN MAX TAKEOFF WEIGHT 992105 MAX MIN Sues
18. degrees until it is securely loaded Fold the seat back up into position Figure 35 Section 4 Load Mast Lever August 2009 Issue 2 2 Page 23 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 12 Install Optional Windscreen XT 880mm Hemove windscreen from protective cover Press the clip Part 108917 onto the trike mast brace Wrap the hook and loop around the clip and the mast brace Figure 36 Section 4 Secure Windscreen XT 880mm Locate the bottom centre hole of the windscreen on the centre locator on the cockpit Fasten by placing the O ring washer and then the retaining pin Repeat for the bottom sides Inspect the windscreen attachment prior to every flight Figure 37 Section 4 Secure Windscreen Extension Bottom Clean the windscreen using a soft clean cloth and mild detergent as necessary Wiping the windscreen in one direction only for the life of the windscreen is good practice Nominaly verticaly August 2009 Issue 2 2 Page 24 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 13 Fit the Engine Cowl If the engine cowl has been removed for a pre flight check the following procedure should be used to re fit the cowl Line up the mounting post with the hole in the cowl guide the cowl over the post and line up the cowl so that the thin end points to the rear Place the large washer Part 10
19. figures have been determined with the engine off at maximum take off weight with the trimmer set in the fast configuration 5 6 1 XT 912 Streak and SST Performance 54 kts at MTOW Descent Rate Descent Gradient Glide Distance from 1000ft AGL Table 14 Section 5 Streak and SST Glide 5 6 2 XT 912 Cruze Performance 45 kts at MTOW Descent Rate Descent Gradient Glide Distance from 1000ft AGL Table 15 Section 5 Cruze Glide 5 6 3 XT 912 Merlin Performance 45 kts at MTOW Descent Rate Descent Gradient Glide Distance from 1000ft AGL Table 16 Section 5 Merlin Glide Metric 34 kt 28 kt Metric 34 kt 28 kt Metric 3 9 m s 15 396 2 km Metric 3 0 m s 1496 2 2 km Metric 3 15 m s 14 496 2 1 km Glide data is for ISA conditions Sea Level at 15 deg C August 2009 Issue 2 2 Imperial 770 ft m 15 396 1 2 miles Imperial 590 ft m 1496 1 4 miles Imperial 621 ft m 14 496 1 3 miles PERFORMANCE AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 5 7 Cruise Performance 5 7 1 XT 912 SST Performance at MTOW Cruise Speed Typical Fuel Burn Cruise See Note Range Cruise Table 17 Section 5 SST Cruise 5 7 2 XT 912 Streak Performance at MTOW Cruise Speed Typical Fuel Burn Cruise See Note Range 9 Cruise Table 18 Section 5 Streak Cruise 5 7 3 XT 912 Cruze Performance at MTOW Cruise Speed Typical Fuel Burn Cruise See Note
20. following take off Trim Speed means the indicated airspeed at which the aircraft remains in a stabilised condition without pilot input Va means the aircraft stall speed Va means the aircraft stall maximum rough air speed means the aircraft design diving speed Va means maximum level speed Vue means the indicated airspeed that the aircraft is never to exceed August 2009 Issue 2 2 Page 9 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 3 Use of metric imperial units This AOI uses the metric unit system as the basic system of measurement Where common usage or available instrumentation refer to the Imperial system both units are quoted The following conversion factors are presented as a ready reference to the conversion factors that have been used in this manual 1 Pound Ib 0 4536 Kilogram kg 1 Pound per sq inch psi 6 895 Kilopascal kPa 1 Inch in 25 4 Millimetres mm 1 Foot ft 0 3048 Metre m 1 Statute mile 1 609 Kilometres km 1 Nautical mile NM 1 852 Kilometres km 1 Millibar mb 1 Hectopascal hPa 1 Millibar mb 0 1 Kilopascal kPa 1 Imperial gallon 4 546 Litres 1 US gallon 3 785 Litres 1 1 US quart E 0 946 Litre 1 1 Cubic foot ft 28 317 Litres 1 1 Degree Fahrenheit F 1 8 X C 32 1 Inch Pound in Ib NE 1 Foot Pound ft Ib ue SEWON METES Table 6 Section 1 Metric Impe
21. m sec 976 ft min Best Climb Speed 45 kts 45 kts Sea Level Gradient of Climb 2396 2396 Table 8 Section 5 Cruze Climb 9 3 3 XT 912 Merlin Performance at MTOW Metric Imperial Climb rate 45 kts 3 9 m sec 764 ft min Best Climb Speed 45 kts 45 kts Sea Level Gradient of Climb 17 17 Table 9 Section 5 Merlin Climb Climb data is for ISA conditions Sea Level at 15 deg C 5 4 Airspeed Calibration All Air Speeds in this AOI are expressed as Knots Indicated Air Speeds KIAS unless otherwise noted Below is a table showing the relationship between Indicated Air Speed and Calibrated Airspeed The table assumes zero instrument error Indicated Air Calibrated Air Calibrated Air Speed Speed Speed KIAS KCAS KCAS Standard Windscreen Windscreen Extension Fitted 35 34 32 40 39 36 45 43 41 50 47 45 60 56 52 70 65 61 80 74 70 85 79 74 Table 10 Section 5 Airspeed Calibration August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 5 5 Stall Speeds 5 5 1 XT 912 Streak and SST Stall Performance Stall Speed MTOW otall Speed 320 kg TOW 35 kt 31 kt Table 11 Section 5 Streak and SSt Stall Speeds 5 5 2 XT 912 Cruze Performance Stall Speed MTOW Stall Speed 320 kg TOW Table 12 Section 5 Cruze Stall Speeds 5 5 3 XT 912 Merlin Performance Stall Speed MTOW otall Speed 320 kg TOW Table 13 Section 5 Merlin Stall Speeds 5 6 Glide Glide
22. the airfield as indicated on an altimeter with the subscale adjusted to 1013 2 millibars or hectopascals AUW All Up Weight means the weight of the aircraft including occupants fuel quantity engine fluids and removable and disposable equipment CG means the Centre of Gravity Empty Weight Refer to the note at Section 6 2 for the defined empty weight FAA United Stated Federal Aviation Administration means feet per minute HGFA means the Hang Gliding Federation of Australia KCAS means Knots Calibrated Airspeed KIAS means Knots Indicated Airspeed as displayed on the cockpit mounted airspeed indicator kg means weight in kilograms Landing Approach Speed means the airspeed that allows control in turbulence wind gradient or sudden engine failure during landing Manoeuvring Speed means the indicated airspeed above which the pilot may not make full or abrupt control movements QNH means the pressure setting that if set on the subscale of a sensitive altimeter will cause the altimeter to indicate the correct local altitude above mean sea level RAA means the Recreational Aviation Australia Stall Speed means the indicated airspeed at which an uncontrolled downward pitching motion of the aircraft occurs or the forward control bar limit is reached Take Off Safety Speed means the airspeed that allows control in turbulence wind gradient or sudden engine failure during the climb
23. the ultimate responsibility for the airworthiness of the aircraft in which they fly 4 9 11 Starting the engine All controls should be checked with the ignition OFF Passengers should have seat belts secure and be briefed for the flight The engine should be started with the pilot in the front seat The following procedure should be used CAUTION e Park Brake is locked in the on position REMEMBER CLEAR PROP e Fuel cock open e Hand and foot throttle off August 2009 Issue 2 2 Page 34 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES e Turn key switch and power up instrument e Switch both ignitions ON e Apply full choke unless the engine is hot e Check visually that the propeller area is clear and call Clear Prop out loud e Depress start button If the engine refuses to start switch off the ignition before investigation e When the engine starts increase the engine RPM to a little above idle and release the chokes e Oil pressure should indicate within 10 seconds e Warm up the engine Minimum Temperature should be reached before take off Operate for 2 min at 2000 rpm continue at 2500 rpm until minimum temperature of 50 deg C is reached WARNING NEVER LEAVE YOUR AIRCRAFT UNATTENDED WHILE THE ENGINE IS RUNNING Keep an aircraft log and enter any unusual engine behaviour Do not fly unless you have corrected a given problem and recorded the correction in the log 4 9 12
24. 0 LITRES 32mm 30mm LEAD FREE MIN RON 90 EFT SREE AN RON 90 P No 107597 P No 105709 RECOMMENDED FUEL The fuel capacity placard is located on the right side shock absorber Metric or imperial placard required Series Edge XT Series Table 14 Section 2 Fuel Capacity Placard Location 2 7 8 Fuel Tap Placard 55mm 28mm P No 105713 The fuel tap placard is adjacent to the fuel tap on seat mast block on the left side of the aircraft Edge XT Series Location Series Table 15 Section 2 Fuel Tap Placard 2 7 9 Hand Throttle and Ignition Placard 32mm HAND IGNITION THROTTLE 55mm OFF DUAL IGNITION CHECK BOTH CIRCUITS P No 105714 The hand throttle placard is located on the right side seat frame Location adjacent to the hand throttle lever Series Edge XT Series Table 16 Section 2 Hand Throttle and Ignition Placard Page 13 August 2009 Issue 2 2 SECTION 2 LIMITATIONS AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 2 7 10 Pilots Right Seat frame Placard Figure 3 Section 2 Hand Throttle and Ignition Placard 2 7 11 Choke Placard 25mm 55mm PART No 105711 The hand choke placard is located on the left side seat frame adjacent to the hand choke lever Edge XT Series Location Series Table 17 Section 2 Choke Placard August 2009 Issue 2 2 Page 14 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instruc
25. 1 6 Fit U Bracket Cover 40 4 11 7 Velcro U Bracket Face Cover 41 4 11 8 Trimmer Cover 41 4 11 9 Disconnect Nose Catch and Remove Nose Cone 41 4 11 10 Remove Sail Cowling 42 4 11 11 Pull Back Cable 42 4 11 12 Remove Main Sail Battens 42 4 11 13 Remove Kingpost 42 4 11 14 Fold Leading Edges 43 4 11 15 Attach Straps 43 August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 16 Fit Wing Bag 43 4 11 17 Roll Wing 43 4 11 18 Disconnect Base Bar 43 4 11 19 Fit Padding 43 4 11 20 Fold Control Frame 44 4 11 21 Position Battens 44 4 12 Wing Break Down Procedure SST 45 4 12 1 Unload Sprogs 45 4 12 2 Unload Over Centre Tip Battens 45 4 12 3 Remove Tip Battens 45 4 12 4 Remove Undersurface Battens 46 4 12 5 Fit U Bracket Cover 46 4 12 6 Fit Tip Bags 46 4 12 7 Trimmer Cover 47 4 12 8 Disconnect Nose Catch and Remove Nose Cone 47 4 12 9 Strut Bolts at Leading Edge 47 4 12 10 Remove Control Frame Connecting Bolt 48 4 12 11 De Tension Pull Back Cable 48 4 12 12 Remove Main Sail Battens 49 4 12 13 Fold Leading Edges 49 4 12 14 Attach Straps 49 4 12 15 Fit Wing Bag 49 4 12 16 Roll Wing 49 4 12 17 Disconnect Base Bar 49 4 12 18 Fit Padding o1 4 12 19 Fold Control Frame 51 4 12 20 Position Battens 51 4 12 21 Position Struts 51 413 Transportation and Storage 53 4 14 Noise Characteristics 53 August 2009 Issue 2 2 Page 3 AirBorne
26. 110mm THE AIRCRAFT OPERATING INSTRUCTIONS SHALL BE CARRIED WITH THE AIRCRAFT OCCUPANTS MUST BE FAMILIAR WITH INFORMATION NECESSARY FOR SAFE OPERATION PART No 107592 20mm 110mm THIS AIRCRAFT WAS MANUFACTURED IN ACCORDANCE WITH THE LIGHT SPORT AIRCRAFT AIRWORTHINESS STANDARDS AND DOES NOT CONFORM TO STANDARD CATEGORY AIRWORTHINESS REQUIREMENTS PART No 109519 PLACARD LSA WARNING AUSTRALIA 20mm Location The hand book placard 107592 is located on the trike dash below the GX2 Instrument The airworthiness placard 109519 is used on Australian LSA and is located located below the ignition switch Series Edge XT Series Table 11 Section 2 Hand Book and Airworthiness Placard August 2009 Issue 2 2 Page 10 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 4 Wing Vne ASI Placard AIRSPEED KNOTS WING 85 CRUZE 73 CHE MERLIN 66 AirBorne 80mm AUSTRALIA z 6536 CDR REV 2 PART NO 109310 80mm PART NO 109310 AIRSPEED KNOTS AIRSPEED KNOTS WING V_KIAS STREAK3 85 CRUZE 73 WING LS STREAK 3 STREAK3 STREAK3 85KTS 80mm 80mm AirBorne AitBorne AUSTRALIA 6536 CDR REVO 25 04 04 6536 CDR REV 1 2 06 05 PART NO 106617 80mm PART NO 106617 22 06 0 PART NO 107237 80mm PART NO 107237 The Placard is located on the air speed indicator on
27. 12 AIRCRAFT amp SYSTEMS 7 AIRCRAFT amp SYSTEMS DESCRIPTION 7 1 General This section provides descriptions of the aircraft and its systems as well as methods of operation where appropriate Information on the aircraft flight controls is detailed in this section but it is mandatory that you receive professional training prior to any solo flight It is illegal to operate this aircraft in Australia without a licence issued by the HGFA or RAA 7 2 Airframe Wing The Streak 3 Cruze Merlin wings are high performance wire braced weight shift controlled microlight wings The SST wing is a high performancestrut braced weight shift controlled microlight wing The airframe is constructed from 6061 T6 multi sleeved aluminium tubing The multi sleeved leading edge construction is 63 5 60 0 and 57 0 mm tube This large diameter construction designed along with the sail luff curve acts to preload the leading edge and maximise trailing edge tension throughout the speed range The sail is constructed using latest technology in the sail making industry The leading edge is constructed using a PX 20 Mylar cloth The main sail cloth is 6 oz Dacron with a Mylar insert in leading edge pocket A trailing edge band provides minimum stretch when loaded that not only gives long sail life but also improves the top speed by controlling twist AirBorne wings are load tested in excess of 2450 kg Excellent engineering contributes to the relatively lightweig
28. 2 Page 6 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operating Instructions Edge XT 912 SUPPLEMENTS SUPPLEMENTS SUPPLEMENTS 9 TRAINING SUPPLEMENT 9 1 XT 912 Streak Cruze Merlin SST Flight Training Supplement 9 2 Assembly and Break Down 9 3 Aircraft Operation 9 4 Startup 9 5 Take off 9 6 Cruise and Stalls 9 7 Landing 9 8 Emergency Procedures 9 9 Control Locations amp Operation 9 9 1 Flight Controls 9 9 2 Engine Controls 9 9 3 Digital Instrument Panel SkyDat GX2 9 10 Aircraft Performance Data 9 11 Training Recommendations 9 11 1 Landing ag a 30500 O O O NY NY NY ND a August 2009 Issue 2 2 1 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operating Instructions Edge XT 912 SUPPLEMENTS 9 TRAINING SUPPLEMENT 9 1 XT 912 Streak Cruze Merlin SST Flight Training Supplement This supplement is intended to outline the unique characteristics of the XT 912 weight shift control WSO airplane It is not intended to outline all aspects of a WSC aircraft The supplement is intended to be used by a pilot operator who already has extensive knowledge of WSC aircraft operation The performance procedures and unique features of the XT are summarized here and the details are referenced to the appropriate section within the AOI Normal Procedures found in Section 4 of the Aircraft Operating Instructions AOI cover all the Normal Procedures in detail 9 2 Assembly and Break Down oecti
29. 2 Weight Calculator 6 3 3 Metric Fuel Calculator 6 3 4 Imperial Fuel Calculator Ooan rPR N N August 2009 Issue 2 2 Page 1 AirBorne WindSports Pty Ltd SECTION 6 Aircraft Operating Instructions Edge XT 912 WEIGHT BAL amp EQUIP 6 WEIGHT BALANCE AND EQUIPMENT 6 1 General This aircraft must only be flown solo from the front seat All aircraft operations may be carried out whilst solo as when the aircraft is flown dual The fuel capacity must always be considered when measuring the AUW of the aircraft Remember that fuel is measured at 0 7 kg per litre and fuel quantity will alter the aircrafts performance during take off and landing A fuel volume calculator can be found in section 6 3 2 6 2 Aircraft Weight The table in section 6 2 1 shows the weight of the aircraft as weighed during final Quality Assurance at the factory The following page shows if applicable the options that were included when the aircraft was weighed The empty weight shown below can also be found on the limitations placard on the aircraft dash panel A second issue section is included which allows the weight to be revised if any additional equipment is installed or if the empty weight of the aircraft changes for any reason If the empty weight has changed then revised placards are available from Airborne The weight calculators allow for additional weight to be accounted for 6 2 1 Aircraft Weighing Information Typical wing weights are SST
30. 209 Aug 2009 Aug200 Table 4 Section 0 Log Of Effective Pages April 2009 Issue 2 2 Page 6 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 CONTENTS 1 GENERAL 2 LIMITATIONS 3 EMERGENCY PROCEDURES 4 NORMAL PROCEDURES 5 PERFORMANCE 6 WEIGHT BALANCE AND EQUIPMENT 7 AIRCRAFT amp SYSTEMS DESCRIPTION 8 HANDLING SERVICE AND MAINTENANCE 9 SUPPLEMENTS April 2009 Issue 2 2 Page 7 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 This page left blank intentionally April 2009 Issue 2 2 Page 8 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 1 GENERAL 1 1 Introduction NOTE 1 1 4 Warning Notice 1 1 2 Definitions 1 2 General Description 1 1 3 Two View Photos 1 1 4 General Dimensions 1 1 5 General Description 1 2 Symbols Abbreviations and Terminology 1 8 Use of metric imperial units August 2009 Issue 2 2 SECTION 1 GENERAL NAIARA VONN N Page 1 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 GENERAL The Aircraft Operating Instructions AOI has various sections to comply with the ASTM standard The General Aviation Manufacturers Association GAMA format has been adopted and used where applicable for this weight shift controlled microlight The AOI contains information for the XT 912 base coupled with either
31. 2099 over the peg and cowl press down firmly and guide the humpback retaining pin Part 108820 through the hole until the hump goes around the peg Figure 38 Section 4 Engine Cowl Retention Pin Loop the rubber cord over the button at the front of the cowl Inspect the following now and regularly e Cowl for secure fit and possible wear points e Washer and retaining pin for security e Rubber loop for wear and security e Cables and lines aren t fouled Figure 39 Section 4 Engine Cowl Retention Rubber Cord 4 5 14 Park The Aircraft The aircraft should be parked in a crosswind position with the wings base tube secured to the mast brace with the bungie supplied NOTE The wingtip facing the wind should be lowered August 2009 Issue 2 2 Page 25 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Figure 40 Section 4 Park the Aircraft August 2009 Issue 2 2 Page 26 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 6 Complete Trike Pre Flight inspection Ensure that the ignition switches are off prior to inspection Daily inspections as outlined in the Rotax Operator s Manual should be carried out in conjunction with the following inspections Trike base Pre flight Inspection No leaks from fuel system and engine fuel lines secure No Leaks from oil system and engine Fuel On Off valve in the ON positi
32. AIRCRAFT OPERATING INSTRUCTIONS Light Sport Aircraft EDGE XT 912 L STREAK 3 L MICROLIGHT EDGE XT 912 L CRUZE MICROLIGHT EDGE XT 912 L MERLIN MICROLIGHT EDGE XT 912 L SST MICROLIGHT Delegate of AirBorne WindSports Pty Ltd Approved Date 1 August 2009 Wing No This manual is compliant with the ASTM designation f2457 05 Standard Specification for Required Product Information To Be Provided With Weight Shift Control Aircraft AirBorne WindSports Pty Ltd UNIT 22 30 KALAROO ROAD REDHEAD NSW 2290 AUSTRALIA Phone 02 4944 9199 International 61 2 4944 9199 Fax 02 4944 9395 International 61 2 4944 9395 E mail fly airborne com au www airborne com au Copyright AirBorne WindSports Pty Ltd 2006 Part 107605 August 2009 Issue 2 2 Page 1 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 This page left blank intentionally April 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 AIRCRAFT OPERATING INSTRUCTIONS DETAILS PssudBy 4B ate For AirBorne WindSports Pty Ltd Table 1 Section 0 Aircraft Operating Instructions Details MANDATORY SERVICE BULLETINS AS THE SERVICE HISTORY OF THE AIRFRAME EVOLVES AIRBORNE WILL FROM TIME TO TIME ISSUE MANDATORY SERVICE BULLETINS WHICH DETAIL ANY CHANGES TO THE MAINTENANCE MANUALS AIRCRAFT OP
33. AK SST 55 60 KIAS CRUZE 50 55 KIAS SST 60 70 KIAS Table 13 Section 4 Cruise Check 4 9 7 Descent Foot Throttle Reduce Hand Throttle Off Airspeed STREAK SST 49 55 KIAS CRUZE 45 50 KIAS MERLIN 45 50 KIAS Table 14 Section 4 Descent Check 4 9 8 Landing Hand Throttle Off Airspeed STREAK SST 49 KIAS CRUZE MERLIN 45 KIAS Directional Control Nose Wheel Steering Straight Braking Off Then as required Table 15 Section 4 Landing Check August 2009 Issue 2 2 Page 32 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 9 9 After Landing Parking Brake On As required Ignition Switch Off Electrical Switch Off Radio Equipment Off Controls secure Parachute It fitted Insert Safety Pin Table 16 Section 4 After Landing Check August 2009 Issue 2 2 Page 33 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Amplified Procedures 4 9 10 Before Starting Safety is everyone s business Included are only some important safety tips Keep a good lookout be thoughtful and always show your intentions prior to starting Prior to flight a thorough pre flight inspection of the aircraft should be carried out Details of the pre flight inspection are shown earlier in this section Make sure all engine controls are operative and you understand the on off positions of the throttle and ignition These controls are readily acce
34. Borne WindSports Pty Ltd Aircraft Operating Instructions Edge XT912 4 9 3 Before Take Off Park Brake Choke Warm Up Oil Ignition Check Trimmer Fuel Quantity Instruments Circuit Breaker Harnesses Helmets On Off Adjust Idle to 2500 rpm Temp to reach 50 deg C Check temperature and pressure 4000 rpm Speed drop with only one ignition must not exceed 300 rpm Set Fast Increase trim speed Check Sufficient for task Check Check secure Secure Throttle Response Full On 3 seconds Pitch and Roll Full and free movement completed before engine start as well as just prior to take off Controls Table 10 Section 4 Before Take Off Check 4 9 4 Take Off and Initial Climb Pitch Control Neutral Hand Throttle Off Foot Throttle Full On Reduce for minimum TOW Directional Control Nose Wheel Steering straight Rotate at TOSS STREAK SST 49 KIAS CRUZE 45 KIAS MERLIN 45 KIAS Table 11 Section 4 Take Off and Initial Climb Check August 2009 Issue 2 2 Page 31 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 9 5 Climb Foot Throttle Full On Reduce for minimum TOW 5000 RPM Reduce to 5000 rpm once climb established No change if using a reduced power take off Airspeed STREAK SST 49 55 KIAS CRUZE 45 50 KIAS MERLIN 45 50 KIAS Table 12 Section 4 Climb Check 4 9 6 Cruise Speeds Hand Throttle Adjust for Level Flight Airspeed STRE
35. ERATING INSTRUCTIONS OR ANY OTHER DETAILS THAT AIRBORNE DEEMS NECESSARY FOR OWNERS TO BE NOTIFIED OF THE WEB ADDRESS FOR SERVICE BULLETINS IS HTTP WWW AIRBORNE COM AU IT IS THE RESPONSIBILITY OF THE OPERATOR TO KEEP UP TO DATE WITH ANY ROTAX DIRECTIVES THROUGH THE ROTAX WEBSITE April 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 DATA PACKAGE This Aircraft Operating Instructions constitutes one part of the complete data package that accompanies the aircraft Following is a list of each of the components which are required e Aircraft Operating Instructions e XT 912 Maintenance Manual e XT 912 Illustrated Parts Catalogue e Wing Maintenance Manual e Wing Illustrated Parts Catalogue e Rotax Owners Manual e Rotax Maintenance Compact Disk e Radio Manual If Installed e BRS Parachute Manual If Installed Table 2 Section 0 XT 912 Data Package Certification documentation is held by the aircraft manufacturer Contact Information Airborne WindSports Pty Ltd PO Box 7042 Redhead NSW Australia 2290 Telephone 61 2 49449199 Web address airborne com au Or for recovery of the certification documentation should the above contact not be available contact the Civil Aviation Safety Authority of Australia Website http www casa qov au April 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edg
36. ES EMERGENCY PROCEDURES 3 EMERGENCY PROCEDURES 3 1 General 3 2 Airspeeds for Emergency Operations 3 2 1 XT 912 Streak 3 2 2 XT 912 Cruze 3 2 3 XT 912 Merlin 3 3 Emergency Procedures Check List 3 3 1 Engine Failure on Climb Out 3 3 2 Engine Failure at Height 3 3 3 Full Power Engine Shutdown In Flight 3 3 4 Forced Landings 3 3 5 n Air Engine Fire 3 3 6 Ground Engine Fire 3 3 7 Propeller Damage 3 3 8 Sail Damage 3 3 9 Emergency Parachute 3 3 10 Ignition Circuit Failure 3 3 11 Spins and Spiral Descents 3 3 12 Unusual Attitudes 3 3 13 Instrument Failure September 2008 Issue 2 1 SECTION 3 EMERGENCY Page 1 N N AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY 3 EMERGENCY PROCEDURES 3 1 General This section of the AOI describes the procedures to be adopted in the event of an emergency or abnormal situation occurring in this aircraft These procedures are arranged in the sequence considered to be the most desirable in the majority of cases Steps should be performed in the order listed unless a suitable reason to deviate exists This section contains operating procedures for flight and system emergency conditions that are essential for the continued safe operation of the aircraft Always maintain correct airspeed and altitudes in the circuit area Never fly in uncertain weather conditions and
37. Edges Carefully spread both leading edges out half way then spread them both out to the approximate flying position It is essential that the keel and the leading edges are kept in the same plane or damage will result Each wing should be kept low to the ground whilst moving forward 4 2 5 Insert King Post Remove kingpost base padding and plug the kingpost into the socket on the rear most hole of the keel Make sure that the cross bar wires are not twisted and are on either side of the king post Figure 4 Section 4 Insert King Post 4 2 6 Insert Main Sail Battens Remove the battens from the bag Lay out the top surface battens curved in order of descending length toward the tip Place the red battens in the left wing curve forwards and the green battens in the right Insert the top surface battens except for the last three battens otart with the battens closest to the keel The battens are inserted into the pocket with gentle pressure until they meet resistance When securing the battens lift trailing edge push fitting in to sail pocket and rotate fitting downward to lock hinge Figure 5 Section 4 Insert Main Sail Battens August 2009 Issue 2 2 Page 8 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 2 7 Tension Cross Bars Figure 6 Section 4 Tensioning Cross Bar and Shackle Located in Block Pull the webbing handle to tension the crossbars The handle p
38. Equipment FITTED Yes No OPTIONAL EQUIPMENT BRS Emergency Parachute Radio Intercom Training Bars Disk Brakes Engine Cowl Windscreen XT 880mm Table 4 Section 6 Aircraft Weight Optional Equipment August 2009 Issue 2 2 SECTION 6 WEIGHT BAL amp EQUIP Page 3 AirBorne WindSports Pty Ltd SECTION 6 Aircraft Operating Instructions Edge XT 912 WEIGHT BAL amp EQUIP 6 3 Typical Aircraft Weights Empty Weight 172 kg crew 406 kg 895 Ib 1 hr Fuel 18 litres 13 kg Empty Weight 86 kg pilot 356 kg 785 Ib full fuel 70 litres 49kg Table 5 Section 6 Typical Aircraft Weights 6 3 1 Weighing Procedure The trike base should be lifted by the suspension point on the top of the mast Prior to weighing ensure that all fuel is drained and all baggage is removed from the aircraft The weight if changed due to option fitment should be recorded as a new issue and dated accordingly in section 6 2 August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 6 Aircraft Operating Instructions Edge XT 912 WEIGHT BAL amp EQUIP 6 3 2 Weight Calculator The weight calculator has been designed to assist in the calculation of maximum allowable fuel so that MTOW does not exceed 450kg The calculator uses the typical empty weight of the microlight as stated above Adjustments must be made if the microlight is not the typical weight i e if additional options are included Instructions Find the inte
39. LISE THAT that WHILST THE PARACHUTE CONTROLS THE RATE OF DESCENT THE PILOT WILL HAVE e the aircraft has suffered structural damage NO CONTROL OVER THE PLACE THE to the extent that control is not possible or AIRCRAFT WILL LAND e if the aircraft is in an irrecoverable situation where structural damage is likely to occur To operate the parachute pull the handle at least twenty centimetres for the parachute rocket projectile to be activated The parachute will allow the complete aircraft to be lowered to the ground The aeroplane september 2008 Issue 2 1 Page 5 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 SECTION 3 EMERGENCY will descend with a steep nose down attitude and tilted to the left Further information can be found in section 7 17 Proceed as follows T Throttle closed Ignition off Seat belts tight Check parachute Pin removed O U o Deploy parachute L Forced Landing 3 3 10 Ignition Circuit Failure The Rotax engine requires a short circuit on the ignition circuit to stop the engine If the ignition circuit is broken using full choke to flood the engine should stop the engine It is possible to starve the engine by switching the fuel tap off This method is not as quick as using the chokes Do not restart the engine until the fault has been fixed 3 9 11 Spins and Spiral Descents Deliberate spinning is prohibited A spiral dive may develop after a stal
40. Loop 22 4 5 6 X Attach Trimmer To Mast SST only 22 45 7 Remove Keel Extension 22 August 2009 Issue 2 2 Page 1 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 8 Rotate Wing 22 4 5 9 Insert Mast Lever 23 4 5 10 Attach Mast Brace 23 4 5 11 Load Mast Lever 23 4 5 12 Install Optional Windscreen XT 880mm 24 4 5 13 Fitthe Engine Cowl 25 4 5 14 Park The Aircraft 25 4 6 Complete Trike Pre Flight inspection 27 4 7 Fuelling 29 4 7 1 Fuel Tank Capacity 29 4 7 2 Fuel Quantity 29 4 8 Helmet Recommendation 29 4 9 Normal Procedures Check List 29 4 9 1 Before Starting Engine 30 4 9 2 Starting Engine 30 4 9 3 Before Take Off 31 4 9 4 Take Off and Initial Climb 31 4 9 5 Climb 32 4 9 6 Cruise Speeds 32 4 9 7 Descent 32 4 9 8 Landing 32 4 9 9 After Landing 33 4 9 10 Before Starting 34 4 9 11 Starting the engine 34 4 9 12 Taxiing 35 4 9 13 Before take off 35 4 9 14 Take Off 36 4 9 15 Climb 36 4 9 16 Cruise 36 4 9 17 Stalls 37 4 9 18 Descent Approach and Landing 37 4 9 19 Cross Wind Landing and Off 37 4 9 20 Baulked Landing 38 4 9 21 Stopping the Engine 38 4 10 After Landing Securing 38 4 10 1 De Rigging Procedure 38 4 11 Wing Break Down Procedure Streak 3 Cruze and Merlin 39 4 11 1 Unload Tip Struts Clip Type 39 4 11 2 Unload Tip Struts Hinge Type 39 4 11 3 Remove Tip Battens 39 4 11 4 Remove Undersurface Battens 40 4 11 5 Fit Tip Bags 40 4 1
41. Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE Use of AvGas requires higher frequency maintenance intervals If AVGAS is used the Rotax web site should be referenced for maintenance requirements See Rotax service information 18 UL 97 D E Refer to section 2 12 for fuel capacities and limitations 8 5 3 Fuel Sampling There is a draincock on the base of the fuel tank at the left hand side which may be used to check the quality of the fuel and to drain fuel if necessary it is especially important to remove any water that may have been introduced from the system 8 5 4 Checking Fuel The fuel is checked for water and contaminants by draining a sample of the fuel into a clear glass container Once a sample has been taken the quality of the fuel can be checked by looking for any water at the bottom of the glass and checking for any other visual contaminants If the fuel has been sitting for an extended period without use it may be advisable to replace it with fresh fuel 8 5 5 Draining the Fuel Ensure that a suitable receptacle is found for the fuel that is to be drained position the trike above the receptacle and depress the draincock Ensure that there are no ignition sources and that the fuel is disposed of correctly 8 6 Engine Oil System Replenishment The minimum oil level is 3 litres max 3 5 litres This checked and replenished by removing the oil sump lid Rotax has provided service instruct
42. MAL PROCEDURES 4 2 Wing Assembly Procedure Streak 3 Cruze and Merlin The following instructions apply to the Streak 3 Cruze and Merlin wings The sequence of procedures assumes that the wing is packed up If the wing and base were already assembled this section is not required Your instructor should demonstrate the correct assembly and disassembly procedures for your microlight This section is intended as a reference only and assumes prior knowledge of assembly AirBorne trike wings should be assembled standing on the control frame Assembling the wing on the control frame keeps the sail off the ground and therefore less prone to being soiled or damaged The suggested assembly procedure is as follows 4 2 1 Unzip Wing Bag Lay the wing down with the zip up and the nose facing approximately 120 degrees from the wind direction Unzip the bag but do not completely remove it from the wing Undo centre 2 clips August 2009 Issue 2 2 Page 6 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 2 2 Assemble Control Frame Remove control bar and down tube padding Spread the control bar down tubes out and insert the base bar onto the alloy knuckle The pip pin is then inserted from front to back Ensure that the pip pin end cap is secure It should not be possible to remove the cap without depressing the pip pin button Check that all the rigging wires are outside the control frame Fig
43. NEIN FLY SOLO FROM FRONT SEAT ONLY PART No 107600 72mm 2mm 62mm AIRBORNE WINDSPORTS Pty Ltd Newcastle NSW Australia AIRCRAFT TYPE EDGE XT FLIGHT LIMITATIONS DO NOT PITCH NOSE DOWN OR NOSE UP MORE THAN 45 DEGREES FROM HORIZONTAL DO NOT EXCEED 60 DEGREES OF BANK NO NEGATIVE G NO AEROBATIC MANOEUVRES NO INTENTIONAL SPINS NO WHIPSTALLS NO STALLED SPIRAL DESCENTS APPROVED FOR DAY VISUAL METEOROLOGICAL CONDITIONS ONLY WARNINGS 72mm 5 ALWAYS PREFLIGHT AIRCRAFT ENSURE MAST LOCKED IN POSITION BEFORE STARTING ENGINE OPERATE INACCORDANCE WITH LIMITATIONS AND PROCEDURES DETAILED IN THE AIRCRAFT OPERATING INSTRUCTIONS PART No 107596 Location The flight limitation placards are located on the dash either side of the mast brace Engine limitations placard option of metric 107599 or imperial 107600 Series Edge XT Series Table 10 Section 2 Flight Limitations Placards August 2009 Issue 2 2 Page 9 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 2 Dash Placard Locations i A Ve a k e DNE Lo P id 1 yee Hr On XT MES MORE ie T 1 LEES rut d eine Figure 1 Section 2 Flight Limitations Airspeed Circuit Breaker Power Socket and Operators Handbook Placard Locations 2 7 3 Aircraft Operating Instructions Placard applicable for LSA
44. RY OR DEATH YOU ARE REFERRED TO THE OPERATING LIMITATIONS IN SECTION 2 OF THIS MANUAL WARNING THERE ARE INHERENT RISKS IN THE PARTICIPATION IN RECREATIONAL AVIATION AIRCRAFT OPERATORS AND PASSENGERS OF RECREATIONAL AVIATION AIRCRAFT BY PARTICIPATION ACCEPT THE RISKS INHERENT IN SUCH PARTICIPATION OF WHICH THE ORDINARY PRUDENT PERSON IS OR SHOULD BE AWARE PILOTS AND PASSENGERS HAVE A DUTY TO EXERCISE GOOD JUDGMENT AND ACT IN A RESPONSIBLE MANNER WHILE USING THE AIRCRAFT AND TO OBEY ALL ORAL OR WRITTEN WARNINGS OR BOTH PRIOR TO AND DURING USE OF THE AIRCRAFT THE OWNER AND OPERATOR MUST UNDERSTAND THAT DUE TO INHERENT RISK INVOLVED IN FLYING A MICROLIGHT ULTRALIGHT TRIKE POWERED HANG GLIDER NO WARRANTY IS MADE OR IMPLIED OF ANY KIND AGAINST ACCIDENTS BODILY INJURY OR DEATH OTHER THAN THOSE WHICH CANNOT BY LAW BE EXCLUDED THE SAFE OPERATION OF THIS AIRCRAFT RESTS WITH YOU THE PILOT WE BELIEVE THAT IN ORDER TO FLY SAFELY YOU MUST MATURELY PRACTICE AIRMANSHIP THE SETTING UP AND BREAKING DOWN A MICROLIGHT ULTRALIGHT TRIKE POWERED HANG GLIDER TRANSPORTATION AND FLYING WILL HAVE AN EFFECT OVER TIME ON ITS STRUCTURAL INTEGRITY THE AIRCRAFT WILL REQUIRE MAINTENANCE AS OUTLINED IN THE APPLICABLE MAINTENANCE MANUALS LIKE ANY AIRCRAFT SAFETY DEPENDS ON A COMBINATION OF CAREFUL MAINTENANCE AND YOUR ABILITY TO FLY INTELLIGENTLY AND CONSERVATIVELY WE HOPE THAT YOUR AIRCRAFT WILL PROVIDE YOU WITH MANY HOURS OF SAFE AND ENJOYABLE FLYING
45. T 912 Electrical Schematic August 2009 Issue 2 2 Page 7 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS e aue BLUE WIRING LOOM GREEN WIRING LOOM iy UN TEST 8 D iy GX2 DISPLAY MODULE SEE SECT 3 5 FOR DETAILS RECTIFIER REGULATOR OU uU e P TEST2 5 YELLOW WIRING LOOM YELLCHN AED m 7 BLACK WIRING LOOM TEST 3 CAPACITOR YELLOW WHITE 22 000 uF 253 Ae INTERCOM SYSTEM TEST 10 11 RED a u RADIO TEST 4 RED CIRCUIT BREAKER 2 r MASTER SWITCH LJ RELAY j E cy f YELLOW START BUTTON 9 c 4 71 aT BATTERY TEST 6 gen Edd DID 20 RED WIRING LOOM WHITE WHITE WIRING LOOM SOLENOID BROWN BAOWN BROWN BROWN WIRING LOOM REFER TO ROTAX INSTALLATION MANUAL SECTION 17 PG 46 INSTALL 912 ELECTRIC SYSTEM Ens TOW Figure 3 Section 7 Electrical Schematic August 2009 Issue 2 2 Page 8 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 15Pitot Static System and Instruments The Pitot static system supplies ram air pressure to the air speed indicator from the nose of the cockpit The static pick up is at the rear of the instrument under the dash 7 16 GX2 Instrument Function The GX2 instrument has preset alarm limit thresholds If any
46. WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 NORMAL PROCEDURES 4 1 General This section of the AOI describes procedures for normal operations of this aircraft WARNING NO ATTEMPT SHOULD BE MADE TO FLY THE AIRCRAFT WITHOUT APPROPRIATE WEIGHT SHIFT AIRCRAFT FLIGHT TRAINING WITH AN APPROVED INSTRUCTOR 4 1 1 XT 912 SST Speeds for Normal Operation Trim Speed 60 66 knots Stall Speed at Maximum Take Off Weight 35 knots Take Off Safety Speed amp 49 knots Nominated Approach Speed at MTOW Maximum Speed in Turbulence Va 70 knots Maximum Level Speed Vha 80 knots Max wind operating conditions At ground 20 knots level Cross winds of up to 12 knots Table 1 Section 4 SST Speeds for Normal Operation 4 1 2 XT 912 Streak 3 Speeds for Normal Operation Trim Speed 55 60 knots Stall Speed at Maximum Take Off Weight 35 knots Take Off Safety Speed amp 49 knots Nominated Approach Speed at MTOW Maximum Speed in Turbulence Va 70 knots Maximum Level Speed Vh 80 knots Max wind operating conditions At ground 20 knots level Cross winds of up to 12 knots Table 2 Section 4 Streak 3 Speeds for Normal Operation August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 1 3 XT 912 Cruze Speeds for Normal Operation Trim Speed 47 52 knots Stall Speed at Maximum Take Off Weight 34 knots Take Off Saf
47. age 2 AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY 3 3 Emergency Procedures Check List 3 3 1 Engine Failure on Climb Out If your engine fails on climb out maintain airspeed reduce angle of attack and land straight ahead if possible Proceed as follows C Maintain Control A Maintain Airspeed take off safety speed L Forced Landing straight ahead if possible 3 3 2 Engine Failure at Height If the engine stops while operating at cruise or full power when the aircraft is well clear of the ground check C Fuel Contents F Fuel tap on Ignition on If your engine fails in flight do not attempt to restart the engine unless one of these items is found to be incorrect and is able to be rectified Relax and maintain control whilst concentrating on correct forced landing techniques 3 3 3 Full Power Engine Shutdown In Flight If the throttle should jam full open in flight proceed as follows C Maintain Control H Get Height With engine at full power adjust height and ground position to improve the outcome of a forced landing A Increase Airspeed to keep the climb angle less than 30 degrees above the horizontal owitch off Ignition L Prepare for forced Landing 3 3 4 Forced Landings Proceed as follows C Maintain Control and airspeed nominated approach speed Throttle Closed Ignition off Fuel tap off Seat belts tight Helmets tight Limbs arms and hands inside s
48. always fly within your proven ability Be sure only to extend your capabilities under planned training situations Carry out safe airmanship whilst flying and be aware of possible emergency landing areas along your flight path If possible check these areas from the ground as you enter the airfield or flying site This technique is for safety reasons as engines are susceptible to stopping no matter how reliably manufactured or maintained Keep a good lookout for other aircraft always be thoughtful and show your intentions Demonstrate good airmanship always It should be remembered that the manufacturer cannot foresee all conceivable circumstances Particular circumstances such as multiple or unanticipated emergencies adverse weather etc may require modification to these procedures A thorough knowledge of the aircraft and its systems is required to analyze the situation correctly and to determine the best course of action 3 2 Airspeeds for Emergency Operations 3 2 1 XT 912 Streak opeed IAS Maximum Manoeuvring 70 knots Speed Va Best Glide 50 knots Table 1 Section 3 Airspeeds for Emergency Operations 3 2 2 XT 912 Cruze Speed IAS Maximum Manoeuvring 66 knots Speed V Best Glide 45 knots Table 2 Section 3 Airspeeds for Emergency Operations 3 2 3 XT 912 Merlin Speed IAS Maximum Manoeuvring 66 knots Speed V Best Glide 44 knots Table 3 Section 3 Airspeeds for Emergency Operations September 2008 Issue 2 1 P
49. ard Professional training is required for the correct procedures of unusual attitude recovery WARNING REDUCED POWER TAKE OFFS WILL EXTEND TAKE OFF DISTANCE IT IS THE PILOTS RESPONSIBILITY TO ENSURE THAT THERE IS SUFFICIENT RUNWAY AVAILIABLE TO CLEAR ALL OBSTACLES WHEN CONDUCTING REDUCED POWER TAKE OFFS 4 9 16 Cruise When the desired flight altitude is reached the aircraft may be levelled out and throttle reduced to that required to maintain level flight The hand operated throttle on the right side of the seat frame can be used to set engine rpm Once the hand throttle is adjusted the pressure on the foot pedal may be removed When the hand throttle is actuated increased power can still be achieved with the use of the foot throttle The rpm will always return to the cruise setting when foot pressure is removed If the hand throttle is set a reduction in RPM is not achievable using the foot throttle The hand throttle must be in the off position to achieve low RPM August 2009 Issue 2 2 Page 36 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT912 4 9 17 Stalls In practice it is only possible to induce a nose down stall of the aircraft in level flight at high take off weights The onset of stall is indicated by a significant increase in control bar loads Recovery from a mild stall is very gentle whether power is on or off Recovery is quick with height loss of less than 50 ft with no tendency to break
50. at all the rigging wires are outside the control frame Figure 14 Section 4 Assemble Control Frame 4 3 3 Stand The Wing Up Rotate the control frame to the vertical position so that the wing is resting on the control bar Do not attempt to connect the nose catch now Remove the glider bag and unclip all the wing straps Figure 15 Section 4 Stand the Wing Up 4 3 4 Spread Leading Edges Carefully spread both leading edges out half way then spread them both out to the approximate flying position It is essential that the keel and the leading edges are kept in the same plane or damage will result Each wing should be kept low to the ground whilst moving forward August 2009 Issue 2 2 Page 12 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 3 5 Connect Control Frame To Wing Struts Place the right hand strut so that it is in line with the right hand downtube Ensure the strut has the airfoil facing forward and note there is a left hand and a right hand strut that ensures correct angle of attack Insert the bolt from the front and secure the wingnut using the safety pin Repeat for the other side Figure 16 Section 4 Connect Control Frame To Wing Struts 4 3 6 Connect Strut at Leading Edge Move the strut so that it is under the leading edge Move the strut and leading edge together to line up the brackets Insert the bolt from the front and check that it seats flush on t
51. ced before the pilot alights from the aircraft A force of approximately 15 20 kg pull on the actuating handle is required to activate the BRS rocket motor Emergency procedures for use of the BRS can be found in section 3 3 9 of this manual Additional information including service and maintenance requirements can be found in the BRS manual 7 18Ilgnition Switches The ignition switches are located on the lower right side of the seat frame Operation is forward for on and rearward for off When the switches are in the off position the switch shorts the engine coils to earth causing the engine to stop August 2009 Issue 2 2 Page 11 AirBorne WindSports Pty Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE HANDLING SERVICE AND MAINTENANCE HANDLING SERVICE AND MAINTENANCE 8 HANDLING SERVICE AND MAINTENANCE 8 1 Introduction 8 2 Identification Plate 8 3 Aircraft Documents 8 4 Aircraft Inspection Maintenance and repair 8 5 Fuel System 8 5 1 Filling Fuel Tanks 8 5 2 Fuel Specification 853 Fuel Sampling gt gt gt gt 8 5 4 Checking Fuel 8 5 5 Draining the Fuel 8 6 Engine Oil System Replenishment 8 6 1 Lubricating Oil 8 7 Cooling System 8 8 Tyre Inflation 8 9 Shock Struts 8 9 1 Hear Shocks 8 9 2 Front Shocks 8 10 Brake System 8 10 1 Brake System Maintenance 8 11 Parking and Ground Handling 8 12 Circuit Breaker and Fuses 8 12 1 Wing Daily Maintena
52. channel Figure 49 Section 4 Disconnect Nose Catch and Remove Nose Cone August 2009 Issue 2 2 Page 41 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 10 Remove Sail Cowling Undo the securing Velcro tabs at the front of the cowl Remove the sail cowling from the top of sail Figure 50 Section 4 Remove Sail Cowling 4 11 11 De Tension Pull Back Cable Depress quick clip with left thumb Use right hand to pull on the webbing handle Remove the shackle from the quick clip block and allow webbing handle to move forward Figure 51 Section 4 De tension Pull Back Cable 4 11 12 Remove Main Sail Battens Pull the leading edges together approximately 1 2 metre Remove the remaining main sail battens Insert battens in the batten bag NOTE The straight battens are inserted in separate pockets Figure 52 Section 4 Remove Main Sail Battens 4 11 13 Remove Kingpost Remove the kingpost by lifting upward Fit the quick clip Kingpost base cover around the quick clip Insert the kingpost in to pouch Figure 53 Section 4 Remove Kingpost August 2009 Issue 2 2 Page 42 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 14 Fold Leading Edges Fold both wings in symmetrically bringing both leading edges back at the same time or in small steps side to side Roll the sail inwards parallel to the l
53. dth Wing Packed Length Wing Length Short Packed Table 4 General Dimensions Merlin 1 1 4 5 XT 912 Outback DIMENSIONS Trike Length Height Trike Base propeller Height Minimum Trike Base Table 5 Section 1 General Dimensions August 2009 Issue 2 2 Australian 9 97m 14 4 sq m 51kg 3 65 m 1 91 m 2 8 m 1 7 m 1 89 m 2 53 0 7 m 5 6 m 4 2 m Australian 9 97 m 13 4 sq m 49 kg 3 65 m 1 91 m 2 8 m 1 7 m 1 89 m 2 53 0 7 m 5 6 m 4 2 m Australian 2 3 mM 1 63 m 1 30 m European 9 97 m 14 4 sq m 6 9 51kg 3 65 m 1 91 m 2 8 m 1 m 1 89 m 2 53 0 7m 5 6 m 4 2 m European 9 97 m 13 4 sq m 7 4 49 kg 3 65 m 1 91 m 2 8 m 1 7 m 1 89 m 2 53 0 7m 5 6 m 4 2 m European 2 3m 1 63 m 1 30 m SECTION 1 GENERAL USA 32 7 ft 155 sq ft 112 lbs 11 9 ft 6 3 ft 9 2 ft 5 6 ft 6 2 ft 8 3 ft 2 3 ft 18 4 ft 13 8 ft USA 32 7 ft 145 sq ft 108 Ibs 11 9 ft 6 3 ft 9 2 ft 5 6 ft 6 2 ft 8 3 ft 2 3 ft 18 4 ft 13 8 ft USA 9 0 ft 5 3 ft 51 2ft Page 6 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 1 5 General Description 1 1 5 1 Base Tourer Model The XT 912 trike base is a two seat in line weight shift controlled aircraft A Rotax 912 four stroke engine producing 80 HP powers the base The layout is typical of this class of two seat trike design with the pilot passe
54. e 3 Section 7 GX2 Features 7 16 2 System Turn Turn key clockwise to the on position Press the ON OFF push button of the panel The alarm lamp will flash briefly If the lamp does not flash it should be rectified prior to flight as the flashing lamp indicates an over temperature situation The display will light up prompting you to reset the flight duration to zero by pressing QNH If the fuel flow option is installed to reset the accumulated fuel consumed press QNH After a few seconds the different engine measurement indications will be displayed The green LED on the capture module should be continually flashing The preset engine limits can be checked against the limits outlined in section 2 4 2 by noting the position of the larger square bars on the LCD display for the particular gauge Altimeter Adjustment You can adjust the barometric pressure as follows QNE Depress both buttons TJ on the left of the instrument simultaneously to set at 1013mb QNH Depress f to increase altitude pressure Depress J to decrease altitude pressure The pressure display is right under ALT in the center of the altimeter The readout below pressure display is a digital altimeter reading The preset limits can be checked against the limits outlined in section 2 4 2 by noting the position of the larger square bars on the LCD display for the particular gauge Changing units system At any time with the instrument turned on press a
55. e XT 912 AMENDMENT RECORD SHEET _ Amendment Date Affected Sections Affected Pages DateInserted Signature Table 3 Section 0 Amendment Record Sheet Manuals will be revised from time to time and re issue of amended pages will be achieved by sending the pages to the current owner registered on AirBorne s database Amendments will also be available on the Airborne website http www airborne com au The amended pages should be printed and the prior page replaced in the manuals folder as soon as possible The amendment table should at that time be updated with the appropriate details and date April 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 0 Aircraft Operating Instructions Edge XT 912 LOG OF EFFECTIVE PAGES Page Issue Date Page Issue Date Page Issue Date Aug 2009 Aug 2009 0 6 lssue22 Aug 2009 Aug 2009 0 8 lssue22 Aug2009 46 lssue22 Aug2009 4 52 Issue 2 2 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 6 6 lssue2 2 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 2 20 lssue2 2 Aug2009 4 35 Issue 2 2 Aug2009 86 Issue 2 2 Aug 2009 Aug 2009 Aug 2009 Aug 2009 Aug 2009 3 4 Issue2 2 Aug2009 4 41 Issue 22 Aug2009 96 Issue 2 2 Aug 2009 3 5 Issue22 Aug2009 442 Issue2 2 Aug2009 3 5 Issue22 Aug2009 443 Issue2 2 Aug
56. e changed to the newly recommended coolant The directive requires that the new coolant be used and a sticker be placed on the coolant cap which prohibits the use of water in the coolant system August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS The coolant should be replaced according to the Rotax maintenance manual current issue Please refer to the directive which is available from the Rotax website SB 912 043 September 04 WARNING WATER OR WATER CONTAINING COOLANT MUST NOT BE ADDED IN ANY CASE TO THE COOLING SYSTEM WITH THE NEW EVANS NPG COOLANT Field service Instructions If EVANS NPG coolant is not locally available temporarily top off the system with propylene glycol antifreeze and be sure not to add water Within 15 days the temporary coolant should be completely drained and the system refilled with EVANS NPG coolant Rotax SB 912 043 Pg 5 2 4 6 Propeller The XT propeller is a carbon fibre composite three bladed propeller Two alternate propeller hub assemblies are available on the aircraft Bolly Blade Description BOS 3 68 X 58 SL 3B Hub Engine Type BOS 3 to suit Rotax 912 True Propeller size 66 1676 Warp Drive Blade Description Warp Drive 68 INCH 3 blades Hub Engine Type HPL R 914 Pattern True Propeller size 67 7 1720mm The maximum propeller speed of 2387 RPM has been determined by test The maxi
57. e emergency parachute when installed placard is located on the inside left rear of the cockpit when the optional emergency parachute Is fitted Series Edge XT Series Table 27 Section 2 Emergency Parachute 2 26 Emergency Parachute Placard Location WARNING E MERGENCy PARACHUT TO E WI MB L E y 1 rer Wer Fit ills Mt See K Figure 8 Section 2 Parachute Placard Location Pilots Left on Pod near to Seat Frame August 2009 Issue 2 2 Page 21 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 27 Emergency Parachute Warning Placard NEVER POINT ROCKET TOWARD ANYONE AT ANY TIME ACCIDENTAL ACTIVATION MAY CAUSE DEATH OR SERIOUS INJURY TREAT LIKE A LOADED GUN c 3 25 v Location The emergency parachute warning placard is located on the parachute rocket on the rear of the aircraft Series Edge XT Series Optional Fitment Table 28 Section 2 Emergency Parachute Warning 2 7 28 Under Seat Bag Placard Under Seat Bag 35mm Maximum Load 2 Anstralia P No 106674 Location The under seat placard is located under the front seat one placard per side beside the start of the zip Series Edge XT Series Table 29 Section 2 Under Seat Placard August 2009 Issue 2 2 Page 22 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 EMERGENCY PROCEDUR
58. e the keel extension fitted with the clevis pin and ring installed This section is intended as a reference only and assumes prior knowledge of the break down procedure Further reference for cover positioning can be found in the wing Illustrated Parts Catalogue IPC 4 11 1 Unload Tip Struts Clip Type Push the Tip Strut so that it opens the clip Remove the hook from the sail eyelet Remove the strut Figure 41 Section 4 Detension Tip Strut 4 11 2 Unload Tip Struts Hinge Type Fold the tip struts pushing the hinge joint towards the center of the wing Once the sail end of the strut is inside the undersurface fold the strut forward and towards the tip of the wing and locate on top of leading edge Figure 42 Section 4 Detension Tip Strut 4 11 3 Remove Tip Battens vk beak from threaded end Rotate pivot beak and Sim remove from sail as shown To adjust batten load tension release pivot beak from sail and rotate batten clip See maintenance manual for adjustment details Threaded a Sh j Remove outermost three tip battens Unclip pivot AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Figure 43 Section 4 Remove Tip Battens 4 11 4 Remove Undersurface Battens Insert finger through string loop and pull batten forward Once the batten is forward pull string down to remove oval pocket Slide batten rearward until all the way out
59. eading edge Attach a strap around one wing Repeat for the other side Fit the keel end pouch Figure 54 Section 4 Fold Leading Edges 4 11 15 Attach Straps Once the leading edges are together apply slight pressure downwards on the keel to raise the leading edges above the down tubes and attach strap around both wings and keel Attach remaining straps so that they are evenly spaced 4 11 16 Fit Wing Bag Position the wing bag to the nose of the wing Stretch bag down the wing to enclose the tips 4 11 17 Roll Wing Hold the wing and down tube and roll the wing onto its back with the control frame to the side 4 11 18 Disconnect Base Bar Depress pip pin button and remove pip pin from base bar Fold down tubes together with base bar folded out Re insert the pip pin Figure 55 Section 4 Disconnect Base Bar qus 4 11 19 Fit Padding Fit the base bar and down tube covers Velcro the base bar cover in whilst holding the base bar in position BIY i un 31 11111 Bn JI Tm ul P A Figure 56 Section 4 Fit Padding August 2009 Issue 2 2 Page 43 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 20 Fold Control Frame Undo centre two wing straps Route flying wires between the down tube and lower the control frame into the wing whilst holding tension on wires Avoid kinking the flying wires 4 11 21 Position Battens otow the batt
60. eat frame m Carry out final approach and Landing as closely as possible to normal power off landing procedure September 2008 Issue 2 1 Page 3 AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY 3 3 5 In Air Engine Fire For fire occurring whilst in flight the initial procedure would be to maintain control of the aircraft and evaluate the extent of the fire This emergency is unlikely to occur but to avoid any further problems use common sense and land the aircraft safely Proceed as follows C Maintain Control F Fuel tap off T Full Throttle to exhaust engine system fuel as soon as possible and maximise slipstream to clear flames from passengers and airframe When fuel is exhausted then Ignition off Forced Landing After landing release seat Belt Release Passenger seat belt m uuTr Evacuate aircraft September 2008 Issue 2 1 Page 4 AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY 3 3 6 On Ground Engine Fire For fire occurring whilst in motion on the ground proceed as follows C Maintain Control S Use remaining Speed to clear people aircraft and buildings T Throttle closed Ignition Off B After stopping release seat Belt P Release Passenger seat belt F Fuel tap off E Evacuate aircraft 3 3 7 Propeller Damage The indication of propeller damage is usually felt by extreme vibration and lack of thr
61. eel Base Trike Height Cockpit Width Wing Packed Length Wing Length Short Packed Table 2 Section 1 General Dimensions SST August 2009 Issue 2 2 Australian 9 97m 13 5sqm 50 kg 3 65 m 1 91m 2 8 m 1 7 m 1 89 2 53 0 7 m 5 6 m 4 2 m Australian 9 97 m 13 5 sq m 58 kg 3 07 m 1 91 m 2 8 m 1 7 m 1 89 m 2 53 0 7 m 5 6 m 4 2 m European 9 97 m 13 5 sq m 7 4 50 kg 3 65 m 1 91 m 2 8 m 1 7 m 1 89 m 2 53 0 7m 5 6m 4 2 m European 9 97 m 13 5 sq m 7 4 58 kg 3 07 m 1 91m 2 8 m 1 m 1 89 m 2 53 0 7m 5 6m 4 2 m SECTION 1 GENERAL USA 32 7 ft 146 sq ft 110 Ibs 11 9 ft 6 3 ft 9 2 ft 5 6 ft 6 2 ft 8 3 ft 2 3 ft 18 4 ft 13 8 ft USA 32 7 ft 146 sq ft 128 Ibs 10 1 ft 6 3 ft 9 2 ft 5 6 ft 6 2 ft 8 3 ft 2 3 ft 18 4 ft 13 8 ft Page 5 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 1 1 4 3 XT 912 Cruze DIMENSIONS Wing Span Wing Area Aspect Ratio Wing Weight Overall Height Control Bar Fwd Trike Width Trike Length Wheel Track Wheel Base Trike Height Cockpit Width Wing Packed Length Wing Length Short Packed Table 3 Section 1 General Dimensions Cruze 1 1 4 4 XT 912 Merlin DIMENSIONS Wing Span Wing Area Aspect Ratio Wing Weight Overall Height Control Bar Fwd Trike Width Trike Length Wheel Track Wheel Base Trike Height Cockpit Wi
62. emove Tip Battens August 2009 Issue 2 2 Page 45 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 12 4 Remove Undersurface Battens Insert finger through string loop and pull batten forward Once the batten is forward pull string down to remove oval pocket Slide batten rearward until all the way out Figure 61 Section 4 Remove Undersurface Battens 4 12 5 Fit U Bracket Cover The U Bracket cover stays in the sail when the wing is assembled Unzip the centre zip and pull each side of the padding down and over the tops of the U Bracket and downtubes Fit each of the down tube padding on the downtubes Figure 62 Section 4 Fit U Bracket Cover 4 12 6 Tip Bags Roll sail at the tips inwards and parallel to the leading edge Slide the tip bag over the end of the leading edge The barrel lock unit can be used to tension the bag bungee Figure 63 Section 4 Fit Tip Bags August 2009 Issue 2 2 Page 46 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 12 7 Trimmer Cover If applicable position the trimmer handle so that the handle is at 90 degrees to the down tube with the knob facing forward Fit the trimmer cover Figure 64 Section 4 Trimmer Cover 4 12 8 Disconnect Nose Catch and Remove Nose Cone Hemove the nose cone Disconnect nose catch by removing the pip pin The pip pin but
63. ens with the curve down at the rear of the glider bag Reattach wing straps so that the control frame and battens are within the leading edge pockets Zip up the wing bag Figure 57 Section 4 Position Battens August 2009 Issue 2 2 Page 44 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 12 Wing Break Down Procedure SST This section assumes that the wing has been removed from the base The wing should have the keel extension fitted with the clevis pin and ring installed This section is intended as a reference only and assumes prior knowledge of the break down procedure 4 12 1 Unload Sprogs Undo the zips and remove the sprog tubes from their pockets inside the sail Note the inboard sprog folds toward the keel and the outboard sprog folds toward the wing tip Figure 58 Section 4 Unload sprogs 4 12 2 Unload Over Centre Tip Battens Unload the lever remove the acetyl roller unit from the sail webbing and remove the batten from the pocket Figure 59 Section 4 Unload Over Centre Tip Battens 4 12 3 Remove Tip Battens 31 Threaded _ i TLO EN Remove outermost three tip battens Unclip pivot uA j beak from threaded end Rotate pivot beak and remove from sail as shown To adjust batten load tension release pivot beak from sail and rotate NE batten clip See maintenance manual for Sa adjustment details Figure 60 Section 4 R
64. ety Speed amp 45 knots Nominated Approach Speed at MTOW Maximum Speed in Turbulence Va 66 knots Maximum Level Speed Vha 70 knots Max wind operating conditions At ground 20 knots level Cross winds of up to 12 knots Table 3 Section 4 Cruze Speeds for Normal Operation 4 1 4 XT 912 Merlin Speeds for Normal Operation Trim Speed 47 52 knots Stall Speed at Maximum Take Off Weight 33 knots Take Off Safety Speed amp 44 knots Nominated Approach Speed at MTOW Maximum Speed in Turbulence Va 66 knots Maximum Level Speed Vj 66 knots Max wind operating conditions At ground 20 knots level Cross winds of up to 12 knots Table 4 Section 4 Merlin Speeds for Normal Operation 4 1 5 Normal procedures Checklist This section is provided to supply the pilot with more comprehensive information of the normal procedures required to operate this aircraft and is written assuming the pilot has been trained in the assembly and use of a weight shift controlled microlight The ultimate responsibility for determining whether the aircraft is in a safe condition to be flown is with YOU the pilot in command Pre flight inspections are outlined in the following sections and are your responsibility if you are the pilot in command Unlike the highway there is no place to pull over and remedy an unsafe problem once you are airborne August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NOR
65. evel markings have been positioned for the fuel tank capacity at 70 litres 4 7 2 Fuel Quantity A sight gauge is provided on the starboard side of the aircraft visible through the soft side Its purpose is to provide fuel volume measurement for calculation of aircraft weight during fuelling of the aircraft and to provide the pilot with a visual indication of the quantity of the remaining fuel The calibration is valid for the aircraft sitting on level ground and indicates total fuel not usable fuel The trike base assumes various flight attitudes according to weight flight speed and power affecting the indicated value of fuel quantity in flight The useable fuel quantity is selected for the worst case condition of aircraft attitude Zero useable fuel is indicated by the fuel level reaching the bottom of the sight gauge during level flight When the level indicates zero useable fuel the tank contains 3 litres of unusable fuel 4 8 Helmet Recommendation The open cockpit of the Edge XT exposes the occupants to the elements during flight and exposes them to objects outside of the aircraft in an emergency situation Helmets and eye protection are recommended for occupants for protection from precipitation strike by insects and birds Helmets are also recommended for risk reduction during an emergency landing of the aircraft The helmets recommended for use in the aircraft are those certified to the EN 966 standard that is applicable to helmets f
66. ft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 2 Position The Trike And Wing Position the wing on its control frame facing into the wind with the nose on the ground The mast tube of the trike should be held down using the strap as described above Check the ighition switches are off Wheel the trike behind the wing rolling the front wheel over the control bar Apply the trike park brake Figure 28 Section 4 Position the Trike and Wing 4 5 3 Attach Mast To Wing U Bracket Allow the main tube to rise by loosening the strap until high enough to connect the universal junction to the wing Insert the bolt with bolt head retaining unit Tighten wing nut firmly and secure safety pin The wing should only be attached using the central hole on the U bracket as shown Remove mast retaining strap Figure 29 Section 4 Attach Wing to Wing U Bracket 4 5 4 Position Heart Bolt Retainer in U Bracket The standard position for the heart bolt in the U bracket is in the centre hole which is the only available point for attachment The heart bolt retainer is positioned in rear open hole to prevent rotation of the bolt Figure 30 Section 4 Heart Bolt Retainer Position August 2009 Issue 2 2 Page 21 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 5 Attach Back Up Loop Connect back up loop so that it passes over the keel and back to the mast Ensure safety pin i
67. g Instructions Edge XT 912 SUPPLEMENTS This page left blank intentionally August 2009 Issue 2 2 Page 6
68. g and before you fly CAUTION ONCE THE WING HAS BEEN PRE FLIGHTED CHECK THAT ALL INSPECTION ZIPS ARE FULLY CLOSED August 2009 Issue 2 2 Page 11 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 3 Wing Assembly Procedure SST The following instructions apply to the SST wing The sequence of procedures assumes that the wing is packed up If the wing and base were already assembled this section is not required Your instructor should demonstrate the correct assembly and disassembly procedures for your microlight This section is intended as a reference only and assumes prior knowledge of assembly AirBorne trike wings should be assembled standing on the control frame Assembling the wing on the control frame keeps the sail off the ground and therefore less prone to being soiled or damaged The suggested assembly procedure is as follows 4 3 1 Unzip Wing Bag Lay the wing down with the zip up and the nose facing approximately 120 degrees from the wind direction Unzip the bag but do not completely remove it from the wing Undo centre 2 clips 4 3 2 Assemble Control Frame Remove control bar and down tube padding Spread the control bar down tubes out and insert the base bar onto the alloy knuckle The pip pin is then inserted from front to back Ensure that the pip pin end cap is secure It should not be possible to remove the cap without depressing the pip pin button Check th
69. ght flown solo shall not be below 55 kg Maximum power at minimum TOW can cause an abrupt climb rate that if uncorrected may cause a wing attitude of greater than the placarded maximum of 45 degrees Approximately 2 3 of maximum take off power is considered comfortable for a minimum weight takeoff Take off distance will be extended at reduced power 2 6 10 Other Limitations Maximum Cross Wind 12 Knots 13 mph Maximum Wind Strength 20 Knots 23 mph Maximum Ambient Operating Temperature uu Fue Eg P Table 9 Section2 Other Limitations No person who is untrained or unqualified in weight shift controlled flight or who is unfamiliar with the wing and base combination should ever attempt to pilot the aircraft unless under professional instruction The effect of light rain on the aircraft can increase the stall speed It is extremely important to maintain speeds in excess of the take off and landing safety speeds when the wing is wet If the aircraft has been left out in the rain or heavy dew it is necessary to wipe the wing down prior to take off It is also recommended that the aircraft be flown solo first to ensure all excess moisture is removed A chamois or sponge is recommended to remove the water Continued operation in heavy rain is not CAUTION recommended due to the abrasive effect of raindrops MOISTURE ON THE WING on the propeller Do not use waterproofing agents on INCREASE STALL SPEED AND SHOULD the wing as the consequent
70. h the local requirements Maintenance requirements are outlined in the base maintenance manual for the base unit and in the wing maintenance manual for the wing The following sections have been included because it is considered that the information may be required on a more regular basis 8 5 Fuel System 8 5 1 Filling Fuel Tanks The properties of the fuel tank material cause an increase in capacity after the first 2 to 3 tanks of fuel Initial capacity is 64 litres with the aged capacity 70 litres The fuel level markings have been positioned for the fuel tank capacity at 70 litres The XT has a single fuel tank When the tank is being filled there may be a slight pressure differential between the sides of the tank causing the fuel cap side to fill slightly faster than the other side Allow time for the breather valves to equalise the pressure to allow complete filling and check that both sides are sufficiently full Fill to the neck of the fuel entrance 8 5 2 Fuel Specification FUEL Preferred Fuel Type En228 Premium Regular Super grade gasoline lead free min RON 90 Optional Fuel Type AVGAS see note Table 1 Section 8 Fuel Specification NOTE Due to higher lead content in AVGAS the wear of the valve seats and deposits in the combustion chamber will increase Therefore use AVGAS only if you encounter problems with vapour lock or if the other fuel type is not available August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty
71. he bracket Secure using the wingnut and safety pin Repeat for the other side Figure 17 Section 4 Connect Strut at Leading Edge 4 3 7 Insert Main Sail Battens Remove the battens from the bag Lay out the top surface battens curved in order of descending length toward the tip Place the red battens in the left wing curve forwards and the green battens in the right Insert the top surface battens except for the last three battens otart with the battens closest to the keel The battens are inserted into the pocket with gentle pressure until they meet resistance When securing the battens lift trailing edge push fitting in to sail pocket and rotate fitting downward to lock hinge Figure 18 Section 4 Insert Main Sail Battens August 2009 Issue 2 2 Page 13 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 3 8 Tension Cross Bars Figure 19 Section 4 Tensioning Cross Bar and Shackle Located in Block Pull the webbing handle to tension the crossbars The handle pull back system gives a mechanical advantage of 2 1 Tension until the cross bar wire shackle is located in the quick clip block behind the safety button 4 3 9 Attach Nose Catch The nose catch should now be attached so that the pip pin is inserted through both the nose catch and channel Ensure the pip pin cap is secure Figure 20 Section 4 Attach Nose Catch 4 3 10 Locate Nose Battens Inser
72. he AirBorne Team has developed from the long standing friendship of a group of enthusiasts who share conviction in the intrinsic advantages of weight shift controlled aircraft The AirBorne Team is confident your new microlight will provide you with many years of enjoyable flying and we wish you and your family safe and happy flying for the future The operating procedures outlined in this handbook are the result of AirBorne s knowledge and experience gained since 1983 NOTE AirBorne data packages will be revised from time to time It is therefore important that owners promptly notify Airborne of any changes to their contact details Owners registered on AirBorne s database will be notified of any changes to data and directed to the AirBorne web site http www airborne com au for the applicable pages The amended pages should be printed and the replacement pages inserted in the folder as soon as possible The amendment table should at that time be updated with the appropriate details and date Revised pages will be sent by mail if requested from AirBorne WindSports the contact details are at the front of this manual August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 1 1 Warning Notice WARNING OPERATIONS OUTSIDE THE RECOMMENDED FLIGHT ENVELOPE SUCH AS AEROBATIC MANOEUVRES OR ERRATIC PILOT TECHNIQUE MAY ULTIMATELY PRODUCE EQUIPMENT FAILURE RESULTING IN PERSONAL INJU
73. he Rotax engine is fitted with a gearbox which delivers smooth thrust via a reduction drive This power unit is complemented with a ground adjustable propeller giving the ultimate in performance and reliability The engine is fitted with Bing carburettors with an external dry filter 7 11 Carburettor heating The system is designed to minimize the risk of carburetor icing A heater block is attached directly to the carburetor body with radiator coolant passing through the block The heat from the carburetor body is also transferred to the carburetor spindle and butterfly No significant heating of the intake air takes place so there is negligible loss of engine power All flight performance data has been obtained with the heaters fitted and operational The carburetor heating system will work automatically when on An occasional check that the heater bodies are getting warm is advisable after engine running The system has not been tested under all possible conditions that may prevail therefore its effectiveness cannot be guaranteed in all circumstances Aircraft equipped with this device should never be flown in circumstances where a successful no power landing cannot be made in the event of engine failure August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 12Propeller The aircraft is equipped with a 3 blade composite propeller with ground adjus
74. he aircraft would round out nicely into a glide should the engine fail Finally the Cruze Streak SST wing trimmer located on the lower right down tube should be in the fast trim position see AOI Section 7 5 9 6 Cruise and Stalls Cruise and Stalls are covered in AOI Sections 4 9 8 and 4 9 9 respectively otalls are very mild and in fact very difficult to do unless the aircraft is heavily loaded Recovery is the same as in other WSC aircraft 9 7 Landing See AOI Section 4 8 7 9 and 4 9 9 12 for descent and landing procedures It is not necessary to approach at a higher speed than trim speed unless conditions are extremely turbulent Generally trim speed allows an adequate margin for landing Set the wing trimmer in the fast trim position 9 8 Emergency Procedures see AO Section for emergency procedures 9 9 Control Locations amp Operation 9 9 1 Flight Controls The XT 912 has standard WSC flight controls See Section 7 for a complete description of the aircraft and its systems 9 9 2 Engine Controls Control Location and Operation Master Switch turn on for starter Lower right instrument panel Use key to turn on See AOI okyDat instrument panel oection 7 6 otarter Button Lower right instrument panel below Master Switch Push button to engage starter See AOI Section 7 6 Choke Lever Left side of pilot mounted to seat frame Push lever down to turn choke on Foot Throttle Hight foot above the nose w
75. heel steering bar Ignition Switches Right side of pilot mounted to seat frame Switches moved forward to turn ignition on Hand Throttle Right side of pilot mounted to seat frame above ignition switches Push throttle up and forward to increase power August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operating Instructions Edge XT 912 SUPPLEMENTS 9 9 3 Digital Instrument Panel SkyDat GX2 See Section 7 16 1 for a complete description SKYDAT GX2 Figure 2 Section 9 Digital Instrument Panel SkyDat GX2 The initial display provides Timer and Cumulative Fuel reset options To reset these counters press the corresponding QNH button After a few seconds the display will change to that depicted above The following primary instruments are provided Top right corner use up down QNH buttons to adjust barometric pressure RPM engine the propeller is spinning at slightly less than half this value Lower right Lowerright August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operating Instructions Edge XT 912 SUPPLEMENTS 9 10 Aircraft Performance Data See AOI Section 5 for detailed discussion on performance The information provided below is based standard atmospheric conditions at sea level at Maximum Takeoff Weight MTOW Distances are specified for Sea Level with Max Take Off Power A level dry runway With short grass
76. hock would need to be reinflated and if they do then a proper investigation of the cause should be undertaken 8 9 2 Front Shocks The front shocks should be inflated to 50 psi for each reservoir The top should be inflated first Turn the rebound damper fully clockwise and then anticlockwise for twelve clicks 8 10 Brake System A front wheel drum brake system or an optional rear wheel disk brake system is used on the aircraft Depressing the brake lever on the left hand side of the front footrest actuates the brake on aerotow equipped trikes the aerotow release is the lever on the top left painted yellow A brake lever lock is provided To engage depress foot lever and raise locking lever by hand To disengage depress the foot lever Use wheel chocks when leaving the disk brake equipped aircraft unattended for a period of time 8 10 1 Brake System Maintenance Details of brake bleeding and other required maintenance of the braking system can be found in section 32 40 00 in the maintenance manual 8 11 Parking and Ground Handling Parking and ground handling information can be located in section 4 8 12Circuit Breaker and Fuses The fuses for the electrical equipment are located in two positions 1 The Lynx intercom system has a 1 5A fuse screwed into the side of the box where the headsets and push to talk cables are plugged in 2 The power supply cables for the radio are protected at the rear of the aircraft with inline fuses which te
77. ht of 56 to 49kg Base Attached to the wing by way of a universal joint is the trike base The universal joint allows the free movement of the trike base in pitch and roll by which control is effected The trike base includes the characteristic tricycle undercarriage power plant and cockpit The engine is mounted to the engine platform at the base of the engine A compression rod is used at the top of the engine and attached to the seat mast block A long range fuel tank is mounted beneath the engine platform The pilot cockpit is designed to allow for various size pilots The standard instruments used on the XT are a okydat GX2 and additional analogue airspeed indicator in knots The cockpit has soft sides attached to the pod and encloses the trike base tube and most of the fuel tank The maximum tyre pressure is 30 psi 205 kPa and optimum pressure for general operations is 15 psi 103 kPa 7 3 Flight Controls Flight controls are as follows o Control bar move right Left turn o Control bar push out Pitch up o Push right toe Throttle open o Hand throttle forward Throttle open o Tighten trim cable Slow trim August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 4 Ground Flight Control Ground controls are as follows o Push left pedal Taxi steering right o Push Left Toe Brakes on o Ignition switch forward Switch on
78. ial Fuel Calculator August 2009 Issue 2 2 WEIGHT BAL amp EQUIP Metric Imperial UNIT CONVERSION Gallons US Lites Ib kg MITO b 992 Payload Ib 492 Empty weight Ib 489 Unuseable fuel gal 0 79 Additional eguipment eq BRS of 20 7 Ib Fuel consumption at full power 46 gal hr Example Pilot 200 Ib 20 Ib additional equipment Passenger 190 Ib 15 4 gallons of fuel maximum Page 6 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS AIRCRAFT amp SYSTEMS DESCRIPTION AIRCRAFT amp SYSTEMS DESCRIPTION 7 AIRCRAFT amp SYSTEMS DESCRIPTION 7 1 General 7 2 Airframe 7 3 Flight Controls 7 4 Ground Flight Control 7 5 Trimmer operation 5 1 Streak 3 and Cruze Wings 7 5 2 SST Wing 7 6 Instrument panel 7 7 Undercarriage System 7 8 Seat Adjustment 7 9 Occupant Restraint Harness 7 10 Engine 7 11 Carburettor heating 7 12 Propeller 713 Brake System 7 14 Electrical System 7 14 1 XT 912 Electrical Schematic 7 15 Pitot Static System and Instruments 7 16 GX2 Instrument Function 7 16 1 Description of Features 7 16 2 System Turn On 7 17 Emergency Parachute Optional Equipment OA FP A FP A WW WWW W N N N N ua 8 okt 8 5 h 7 18 Ignition Switches August 2009 Issue 2 2 Page 1 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 9
79. ight Inspection August 2009 Issue 2 2 Page 27 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES August 2009 Issue 2 2 Page 28 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 7 Fuelling Fuel flow is from a single fuel tank fitted with a self venting tube The fuel system is fitted with a shut off valve located on the rear left hand side of the seat frame Be sure this valve is in the ON position before starting engine Never refuel if fuel could be spilled on hot engine components Use only safety approved fuel containers and never transport fuel in an unsafe manner The fuel tank has a water drain mounted at the base and to the rear of the tank The fuel system WARNING has an in line fuel filter which is mounted at the ENSURE THE AIRCRAFT IS EARTHED TO front of the tank This filter can be easily AVOID STATIC DISCHARGE IGNITING FUEL disassembled for cleaning and inspection see DURING THE REFUELLING OPERATION base maintenance manual The Edge XT series fuel levels are marked on the right side of the fuel tank The fuel levels are marked at 10 litres 20 litres 30 litres 40 litres 50 litres and 60 litres 4 7 1 Fuel Tank Capacity The properties of the fuel tank material cause an increase in capacity after the first 2 to 3 tanks of fuel Initial capacity is 64 litres with the aged capacity 70 litres The fuel l
80. ignificant variation to these performance figures 5 2 Take Off and Landing 5 2 1 Take Off XT 912 Streak amp SST Performance at MTOW Metric Take off Distance to 15 m 50 ft 247m Table 1 Section 5 Streak and SST Take Off 5 2 2 Take Off XT 912 Cruze Performance at MTOW Metric Take off Distance to 15 m 50 ft 210m Table 2 Section 5 Cruze Take Off 5 2 3 Take Off XT 912 Merlin Performance at MTOW Metric Take off Distance to 15 m 50 ft 204m Table 3 Section 5 Merlin Take Off Takeoff distances are specified for Sea Level with Max Take Off Power A level dry runway With short grass Still wind And temperature of 15 deg C The following factors will increase takeoff distance Reduced Power Take Off Higher drag runway surfaces such as wet or long grass Tail wind Uphill takeoff OAT above 15 deg C Runway altitude above sea level Imperial 810 ft Imperial 689 ft Imperial 669 ft The pilot is required to take into account the effect of the above when determining takeoff distance August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 5 Aircraft Operating Instructions Edge XT 912 PERFORMANCE 5 2 4 Landing XT 912 Streak and SST Performance at MTOW Metric Imperial Landing Distance from 15 m 50 ft 325m 1066 ft Table 4 Section 5 Streak and SST Landing 5 2 5 Landing XT 912 Cruze Performance at MTOW Metric Imperial Landing Distance from 15 m 50 ft 306m 1004 ft Table
81. il the aircraft makes a complete stop An approach to the airstrip may be made with or without power but in either case the airspeed should be maintained above the nominated approach speed During take off and landing the recommended trimmer setting is in the fast trim position It is acceptable to set the trim as far as mid trim position for take off and landing The decal on the control frame upright adjacent to the trimmer knob indicates the trim position The aircraft should be flown on final approach at or above the nominated safety speed The additional airspeed allows for wind gradient and to provide greater controllability in the rough air that may lie close to the ground Maintaining airspeed on final is very important for engine off landings allowing a margin for round out before touchdown The trike is designed to land with the rear wheels touching down slightly before the nose wheel Once firmly on the ground aerodynamic braking may be achieved by pulling in the control bar then applying the front nose wheel brake NOTE In the case of a heavy landing the maintenance manuals for both the wing and the base should be referenced It must be noted that after a hard landing your aircraft must be completely checked 4 9 19 Cross Wind Landing and Take Off Pilots with less experience should avoid landing or taking off in conditions with high crosswind components as skills do not always match the capabilities of the aircraft Cros
82. ion 2 Shock Absorber Pressure Placard 2 7 22 Right Hand Suspension Strut Placards Figure 7 Section 2 Clear Prop and Fuel Spec Placards August 2009 Issue 2 2 Page 19 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 23 King Post Placard 40MM CHECK ONE WIRE ON EACH SIDE OF KING POST 54MM PART NO 104622 Location The king post placard is located on the rear of the keel tube of the wing Series All wing except SST Table 25 Section 2 King Post Placard 2 7 24 Wing and Base Data Plates AIRBORNE WINDSPORTS PTY LTD REDHEAD NSW AUSTRALIA ASTM S LIGHT SPORT AIRCRAFT xxx DATE OF MANUFACTURE MM YY e MODEL EDGE XT 912 L SERIAL NO 91 2 NNNN Part No 107566 WING PLATE PART NO 102358 Location The wing data plate 102358 is located on the negative block of the universal bracket The base data plate 107566 is located on the seat mast block on the left side of the aircraft Series XT base and applicable wing Table 26 Section 2 Data Plates August 2009 Issue 2 2 Page 20 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 25 Emergency Parachute 5 mm WARNING EMERGENCY PARACHUTE TO OPERATE 1 KILL THE ENGINE 2 JERK THE ACTVATING PANDLE hard 44mm 3 PROTECT BODY Cover Face Keep Limbs Close SEE AIRCRAFT OPERATING INSTRUCTIONS P No 107603 Location Th
83. ions which detail how to check the oil Removing the sump plug drains the sump Ensure that the sump plug is correctly replaced and lock wired prior to refilling the engine with oil Measure the amount to be replaced refill check the level run the engine and recheck The opportunity should be taken to replace the oil filler any time that the oil is replaced Oil Level Instructions Do not overfill the oil system The difference between the min and max marks on the dipstick is 0 45 litres 0 48 qt Figure 1 Section 8 Oil Dipstick Diagram Rotax Service instructions should be consulted 51 27 1997 R1 August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE 8 6 1 Lubricating Oil The 912 UL engine has an external sump and the entire system is standard to the Rotax 912 engine The oil specification is given in the Rotax Operators Manual Section 10 2 3 Lubricants In general use only synthetic or semi synthetic oil API classification SF or SG or later oils Multigrade is recommended These oil types are detergent types Consult the Rotax manual and Rotax service instruction 18 UL 97 for the correct type and grade of oil for the ambient operating temperature Two oils which are recommended by the Rotax Service instruction 18 UL 97 for use with both Avgas and Unleaded fuels are SHELL Advance VSX 4 APISG SAE 15W 50 VALVOLINE Dura Ble
84. ith impressive feel in turbulence The batten ends are a unique design which can be adjusted to vary tension for tuning the wing The batten mechanism allows easy installation and removal of the battens An airfoiled aluminium section is used for the down tubes and king post Clever engineering features fittings that look smart and are positioned to achieve minimum drag The Merlin wing is a state of the art open cross bar design that has been designed to have an unprecedented combination of stability in turbulence and manoeuvrability at low speeds The Merlin retains many of the features of the Streak Cruze series wings with further emphasis on simplicity The SST reflects the requests of customers to develop a topless wing that is a wing without a kingpost and top rigging The SST is based on the Streak 3 and so has similar features but has the benefits of being able to fit in more confined hangars and improved handling and speed ranges due to less drag 1 1 5 3 XT 912 Streak The XT 912 combined with the Streak 3 wing has proven to be an excellent combination The total fuel capacity is 70 litres and combined with the Rotax 912 delivering a smooth 80 HP allows long cross country flights The combination produces a very stable microlight which is perfectly suited to cross country flying August 2009 Issue 2 2 Page 7 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 1 5 4 XT 912 Cruze
85. k to the rear of the pocket Figure 11 Section 4 Insert Remaining Sail Battens 4 2 14 Load Tip Strut Clip Type Insert the tip strut into the batten pocket There is a strut each for the left side and right side When holding the strut with the clip end toward you and with the clip hook facing up the white clip should be outboard and then rotate toward the keel to tighten The left hand side is pictured as a guide The struts are floating and do not locate at the front other than by sliding them into their Issue 2 2 Page 10 SECTION 4 AirBorne WindSports Pty Ltd NORMAL PROCEDURES Aircraft Operating Instructions Edge XT912 pockets Locate the hook in the sail eyelet by moving the trailing edge onto the batten hook Close the clip along the shaft gently but firmly Figure 12 Section 4 Load Tip Strut 4 2 15 Load Tip Strut Hinge Type Early model wings have an aluminium folding tip strut as illustrated in the figure below To install Reach in through the tip and feed the end of the strut out through the undersurface and locate on red webbing Pull on the bracket in the center of the strut until the strut over centers Position hand so that it will not get caught in lever mechanism note photo shows undersurface undone for improved clarity of operation Figure 13 Section 4 Load Tip Strut You are ready for the wing pre flight inspection It is imperative that you carry out this inspection every time you ri
86. l if the bar is maintained at the forward limit and a large roll rate is allowed to develop If this condition is not corrected it will lead to large and increasing roll attitudes beyond the 60 degree limit Increasing attitude increasing speeds and large control bar feed back forces will occur Incipient spiral dives can be terminated at any time by rolling wings level If the spiral dive is allowed to develop to extreme roll attitudes recovery is expedited by relieving control bar forces before rolling wings level and recovering from high speed condition 3 3 12 Unusual Attitudes WARNING DO NOT ATTEMPT TO SPIN THE AIRCRAFT SPIRAL DIVES ATTEMPTED SHOULD NOT BE DURING DESCENDING TURNS AIRCRAFT ATTITUDE MUST BE KEPT WITHIN PLACARDED PITCH ROLL AND AIRSPEED LIMITS Unusual attitudes where the nose is raised or lowered more than 45 degrees from the horizontal are to be avoided On recognising a situation where the aircraft is approaching these pitch angles proceed as outlined below 3 3 12 1 Nose High Attitude To recover from the situation where the nose of the aircraft is pitched up more than 45 degrees from the horizontal proceed as follows H Hold attitude Do not attempt to pull control bar in P Reduce Power O As energy dissipates the aircraft will rotate nose down keep control bar Out P once the attitude lowers level the wings and increase Power to prevent over pitching R Recover from dive and Resume desi
87. lex wing which utilises struts to react the negative flight and landing loads imposed on the wing airframe Removal of the king post and associated top rigging results in a significant decrease in drag which improves cruise performance and reduces fuel consumption The SST matched with the XT 912 will appeal to the pilot who likes a cleaner lower profile look to their aircraft Handling is improved and speed ranges are increased As the strutted wing has no king post and therefore no reflex bridles pitch stability is achieved by using wire braced washout struts or sprogs The sprogs are contained within the sail further assisting in drag reduction The sprogs only become active at low angles of attack The rear of the sprog tubes act upwards on transverse battens which serve to keep the trailing edge of the sail raised maintaining washout and therefore pitch stability The SST retains all of the great handling characteristics of the Airborne wing range The performance benefit of the strutted version with the added advantage of a sleek looking wing with low hanger ability makes the XT912 SST aircraft the choice for the discerning cross country pilot August 2009 Issue 2 2 Page 8 AirBorne WindSports Pty Ltd SECTION 1 Aircraft Operating Instructions Edge XT 912 GENERAL 1 2 Symbols Abbreviations and Terminology In this handbook AOI means Aircraft Operating Instructions Airfield Pressure Altitude or QNE means the altitude of
88. mum propeller speed occurs when the engine RPM reaches 5800 RPM Pitch settings can be found in section 61 10 20 of the maintenance manual 2 4 Engine Instrument Markings The GX 2 instrument has preset alarm limit thresholds If any of these temperature or pressure limitations are reached the red light on the instrument panel will start to flash Limitations can be found in section 2 4 2 5 Weight Limits Metric Imperial Max take off weight 450 kg 992 Ib Typical empty weight 223 kg 492 Ib Maximum empty weight 260 kg 573 Ib Permitted range of pilot weights Front seat 55 100 kg 121 220 Ib Rear seat 0 100 kg 0 220 Ib Total maximum crew weight 200 kg 440 Ib Maximum under seat storage load per bag 2kg 4 Ib Table 5 Section 2 Weight Limits Includes 3 litres 2kg unusable fuel Empty weight is defined in section 6 2 August 2009 Issue 2 2 Page 6 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 6 Operational Limits 2 6 1 Centre of Gravity limits Centre of gravity limits are not critical on the base of a flex wing microlight Having the trike unit attached to the wing from a single universal bracket variations of cockpit loading and fuel loading cannot influence the aircraft s balance The Edge XT is therefore not critical in regards to centre of gravity although the distribution of load in the trike base has a minor affect on the in flight attitude of the trike base Base Sus
89. n off switch for 3 seconds The instrument display will now power up Ensure that the fuel tap is in the on position and both ignition switches are on Once satisfied that all other checks as outlined in section 4 9 1 2 are complete the starter button on the right side of the dash can be depressed Warm up the engine Minimum temperature should be reached before take off Operate for 2 min at 2000 rpm continue at 2500 rpm until minimum temperature of 50 C 140 F is reached August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 9 Aircraft Operating Instructions Edge XT 912 SUPPLEMENTS 9 5 Take off see AO Section 4 8 3 5 and 4 9 3 6 Amplified Procedures for take off and climb procedures Many WSC instructors recommend pulling the control bar in towards the pilot past the wings trim position after lift off As the wing design has the trim speed equal to or greater than 1 3 V Stall Speed it is not necessary to pull the control bar back The wing will return to the trim speed and achieve take off safety speed if the controls are relaxed Initial climb out should be made on full power for maximum take off weight Approximately 2 3 of maximum take off power is considered comfortable for a minimum weight takeoff Take off distance will be extended at reduced power Once climb is established power should be reduced to below maximum continuous power of 5500 rpm A minimum of take off safety speed should be used At this speed t
90. nce August 2009 Issue 2 2 1 AnA a A AO N N N N WD a AirBorne WindSports Pty Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE 8 HANDLING SERVICE AND MAINTENANCE 8 1 Introduction This section contains factory recommended procedures for proper ground handling and routine care for your aircraft Included in this section is relevant information required by the operator WARNING IT IS THE PILOTS RESPONSIBILITY TO ENSURE THAT ALL SERVICE BULLETINS HAVE BEEN ADDRESSED IT IS ALSO THE PILOTS RESPONSIBILITY TO ENSURE SERVICING AND MAINTENANCE HAS BEEN PERFORMED AS OUTLINED IN THE APPROPRIATE MAINTENANCE MANUAL AND IN ACCORDANCE WITH THE APPLICABLE AVIATION REGULATIONS 8 2 Identification Plate The aircraft has two identification plates The wing identification plate can be found on the negative plate of the universal bracket The base identification plate can be found on the seat mast block on the left side of the aircraft The serial number should be quoted when corresponding with the factory 8 3 Aircraft Documents The Aircraft Operating Instructions is one of a series of documents required to safely operate this aircraft A document list can be found in section 0 of this manual under DATA PACKAGE 8 4 Aircraft Inspection Maintenance and repair Maintainer qualifications vary from country to country The operator maintainer should be familiar wit
91. nd Synthetic APISJ SAE 10W 40 Check oil and replenish as required Prior to oil check turn the propeller by hand several times in the direction of rotation or let the engine idle for 1 minute The difference between maximum and minimum oil level mark on the dip stick is 0 45 Litre 0 48 qt Use caution around the hot exhaust header when removing the oil tank cap and checking the dip stick 8 7 Cooling System WARNING DO NOT OPEN THE COOLING SYSTEM WHEN THE ENGINE IS HOT SEVERE SCALDING AND OTHER INJURIES MAY RESULT Water cooling system capacity is 2 5 Litre See maintenance manual for further details Coolant Specification A MANDATORY Rotax Directive was issued on the 25 of November 2004 which requires a change in the type of coolant that must be used with the Rotax 912 type engine From the 23 Feb 2005 the new coolant Evans NPG waterless coolant is to be used The reason for the change is In some instances conventional coolant mixture ratio of 5096 water and 5096 antifreeze can vaporize or boil before the maximum permissible cylinder head temperature is reached Rotax Service bulletin SB 912 043 pg 1 Earlier Airborne trikes have had a silicate free type high quality and long life antifreeze coolant which is red Airborne Part Number 106644 installed in the radiator This coolant must be changed to the newly recommended coolant The directive requires that the new coolant be used and a sticker be placed on
92. nd hold simultaneously the two QNH push buttons After a few seconds the displayed units system will change and be memorized One of the following unit systems may be selected 1 Metric e Altitude in meters with QNH in mbar ASI in km h VSI in m s Temperatures in Celsius Oil pressure in bar August 2009 Issue 2 2 Page 10 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS Fuel consumption in Litres hour 2 pens US Altitude in ft with QNH in inches of Hg ASI in mi h Statute VSI in ft min Temperatures in Fahrenheit Cil pressure in PSI Fuel consumption in gal US hour 3 mpana UK Altitude in ft with QNH in mbar ASI in mi h statute or knots VSI in ft min Temperatures in Celsius Oil pressure in bar Fuel consumption in Litres hour The sequence of change is Metric Imperial UK Imperial US Imperial UK ASI in knots NOTE For Australian operations CASA requires the units to be set to Imperial UK with ASI in knots 7 17 Emergency Parachute Optional Equipment NOTE The parachute is optional unless the governing body of the country where the aircraft is to be flown requires a parachute The BRS emergency parachute system has a double acting firing mechanism The parachute operating handle is fitted with a safety pin and is located on the left side of the seat frame This pin should be removed before each flight and the safety pin must be repla
93. nd radio equipment off The aircraft should be parked in a crosswind position with the base tube secured to the mast brace with the bungie supplied The emergency parachute safety pin should be inserted before leaving the aircraft 4 10 1 De Rigging Procedure Careful attention to the recommended rigging and de rigging sequences will protect the aircraft from the risk of unnecessary damage The de rigging procedure is a direct reversal of the rigging procedure A summary of the procedure follows 4 10 1 1 Hemove Wing from Base oee Section 4 Attaching Wing to Base and use reverse procedure e Apply park brake e series only Undo the trimmer by unclipping it from the wishart clip on the mast see Figure 30 e Remove pip pins from the front support compression tube Slide outer mast brace up and insert pip pin through lower hole this will secure the inner and outer tubes for the lowering phase e Unload and remove over centre latch e lower the wing until the control bar is on the ground e Secure mast with strap to base tube e Unbolt the trike from the U bracket remove safety loop and wheel out the trike unit e Reinstall keel extension tube August 2009 Issue 2 2 Page 38 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 11 Wing Break Down Procedure Streak 3 Cruze and Merlin This section assumes that the wing has been removed from the base The wing should hav
94. nger pod being suspended by a triangular frame hinged from the mast head about the pitch and roll axes to provide for weight shift control The full XT cockpit has a windscreen for improved wind deflection and is cut away at the sides to allow for easier pilot access The wide rear 6 inch wheels remain a feature of the XT base but the wheel pants spats have been redesigned and include integrated aerodynamic fins to improve base yaw stability Tundra Model The XT Tundra version has a cockpit with the inclusion of the larger Tundra tyres The tundra version allows the comfort of the cockpit design with the added advantage of unprepared ground landing ability Larger rear wheel spats are included to improve base yaw stability at higher speeds Outback Model The XT Outback has a spacious instrument housing with windscreen for the comfort of the pilot The reduced lateral area of the instrument housing and windscreen with the absence of cockpit allows the use of large open wheels with no fins and tundra tyres for use on unprepared ground 1 1 5 2 Wing The Streak 3 Cruze Merlin and SST wings are the result of continued refinement of AirBorne trike wings The wings are fairly typical of an established class of swept tapered flexible fabric wings with a relatively high aspect ratio Both the Streak and Cruze sail have several cloth and velcro shear ribs which combined with an excellent sail fit producing a wing that has light handling w
95. o Choke forward Choke on o Fuel Tap Aligned with tap body Fuel on 7 5 Trimmer operation 7 5 1 Streak 3 and Cruze Wings The trimmer system allows in flight trim adjustment by rotating the trimmer wheel on the right downtube Rotation of the trimmer wheel clockwise raises the reflex bridles causing extra reflex in the root section of the wing This causes a reduction in trim speed of 10 15 knots The swage on the trimmer wire is used as a pointer on the trimmer placard 7 5 2 SST Wing Turning the trim handle pulls the keel down at the rear acting like a counterweight This causes a reduction in trim speed of 10 15 knots For all wings during take off and landing the recommended trimmer setting is in the fast trim position lt is acceptable to set the trim as far as mid trim position for take off and landing The decal on the control frame upright adjacent to the trimmer knob indicates the trim position There is a slight increase in roll pressures as the trimmer is used to decrease trim speed The aircraft is designed to be stable at trim under all loads with a small increase in trim airspeed as the AUW is increased 7 6 Instrument panel The instrument panel consists of an analogue airspeed indicator knots on the left side with the digital GX2 instrument mounted centrally in the dash A power circuit breaker power switch 12V DC outlet and starter button can be found on the right side of the dash Figure 1 Section 7 Instrumen
96. ocket You may have to lift the trailing edge to aid placement Secure the sprogs in place by closing the zippers 4 3 16 Load Tip Over Centre Battens Insert the last mainsail battens The acetyl roller unit should be located on the webbing and use the lever to close the hinge Ensure fingers are clear of lever to avoid injury Figure 26 Section 4 Load Over Centre Battens August 2009 Issue 2 2 Page 16 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES You are ready for the wing pre flight inspection It is imperative that you carry out this inspection every time you rig and before you fly CAUTION ONCE THE WING HAS BEEN PRE FLIGHTED CHECK THAT ALL INSPECTION ZIPS ARE FULLY CLOSED August 2009 Issue 2 2 Page 17 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 4 Wing Pre flight inspection The design of the wing is such that junctions not open to view may be reached from zipped inspection panels Start at the nose and move around the wing making the following condition inspections check for damage wear and security Wing pre flight inspection SST Streak 3 Cruze Merlin Nose catch nose bolts sail tangs Nose battens Nose cone aligned Leading edge tubing Crossbar hinge junction amp cross bar tubing Centre undersurface zip oail tip secure and webbing Tip struts Battens Battens secure and pocke
97. of the temperature or pressure limitations are reached the red light will start to flash Standard instrumentation includes the AMPtronics GX2 Digital Flight instrument see description below and an analogue airspeed indicator in knots WARNING IT IS PROHIBITED TO FLY THIS AIRCRAFT WITH THE AMPTRONIC SKYDAT GX2 ALARM THRESHOLDS SET OUTSIDE THE ENGINE MANUFACTURER S LIMITS 7 16 1 Description of Features The GX2 is a combined avionic instrument with programmable functions The system consists of two parts the display module which is mounted in the dash and the capture module which is located on the engine tie rod The photo shows the layout of the display when set up for the 912 Rotax engine ON OFF Figure 4 Section 7 GX2 Display August 2009 Issue 2 2 Page 9 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS GX2 Features ASI mph knots or kilometers ALT Altimeter in feet or meters RPM engine revolutions per minute VSI vertical speed indicator in m s or ft min Flight duration 1 in hours minutes Battery Voltage 4 seconds Engine Hours 5 in hours minutes 2 of CHT cylinder head temperature Celsius or Fahrenheit Oil Temperature 2 of EGT exhaust gas temperature Celsius or Fahrenheit Oil Pressure bars or PSI Air Temperature Fuel flow data is available Accumulative fuel 2 in liters or Fuel Flow 8 in litres or gallons gallons Tabl
98. on Fuel filter clean and operational Fuel drain valve check for any water in tank sump by draining a small quantity into a container oufficient fuel for flight Oil level for oil injection OK see photo below fig 22 Coolant Level Between max and min level on coolant bottle Rotary Valve oil level OK Radiator hoses secure and operational Propeller free of splitting denting delamination nicks Blade tape condition Propeller hub assembly secure and tie wired No cracking in tyre treads or evidence of cracking around the rim Rear end and Wheel Spats secure No bolts bent fractured or evidence of corrosion Electrical amp instrumentation system secure and operational Throttle operation both foot and hand throttle Verify free and full movement Seat belt attachments secure oteering damper adjust to desired setting All engine components secure air filter muffler plug leads locking wires Mast race PIP pins secure Mast over centre latch loaded and secure Windscreen extension secured if fitted Engine cowl secured if fitted Vents oil tank fuel tank Pitot entry Mechanical Components Rotate propeller clockwise and observe for noise or excessive resistance General inspection of complete trike lt Eu lt MM EL 2 E E 2 e e D EM Wing amp base universal bracket secure Back up webbing strap secure Table 7 Section 4 Complete Trike Pre Fl
99. on Maximum 66 knots 59 knots Limited by Vne Manoeuvring Speed Va Vne is limited by the maximum speed capable of being demonstrated in a dive this results in a Vne less than the nominal Va for nominal 4g loading is difficult to attain speeds high enough to reach 4 g loadings in smooth air in these aircraft Table 3 Section 2 Airspeed Limitations 2 3 Airspeed Indicator markings The standard pressure airspeed indicator on the left side of the dash has multiple red radial markings indicating Vne for the wing base combinations The pilot should be aware of the combination of wing and base and be familiar with the appropriate Vne marking August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 4 Power Plant Limitations 2 4 4 Engine Manufacturer Rotax Bombardier Model Rotax 912 UL 2 4 Stroke Gearbox ratio 2 43 1 2 4 2 Engine Limitations ENGINE LIMITATIONS Metric Imperial ENGINE SPEED Take Off Max 5 mins 5800 rpm 5800 rpm Maximum Continuous 5500 rpm 5500 rpm PERFORMANCE Take off Performance 59 6 kW 80 hp Maximum Continuous Performance 58 kW 78 hp OIL PRESSURE Max Allowable for short period at cold start 7 bar 102 psi Minimum Below 3500 rpm 0 8 bar 12 psi Normal Above 3500 rpm 2 0 5 0 bar 29 73 psi OIL TEMPERATURE Maximum 140 deg C 285 deg F Minimum Note 1 50 deg C 120 deg F Normal Operating Temperature 90 110deg C 190 230 deg F
100. ons 4 2 4 and 4 10 11 outline wing assembly and break down procedures for the aircraft Airborne suggests assembling the wing on the control frame as this method keeps the sail off the ground resulting in less chance of the wing being soiled or damaged The wing can be assembled and installed on the base by one person The mast has a gas assist strut to help lift the wing into place above the base unit It should be noted that the batten tips utilise a unique hinged catch system to secure the battens to the trailing edge This system allows easy installation and provides extraordinary flexibility in wing tuning Ensure that the batten end fittings are depressed fully before unloading see wing Maintenance Manual for tuning instructions WARNING IT IS EXTREMELY IMPORTANT THAT THE MAST LEVER IS LOADED CORRECTLY ONCE THE MAST IS RAISED WITH THE WING INSTALLED SEE 4 4 10 FOR FURTHER DETAILS SEE PHOTO OPPOSITE Figure 1 Mast Catch Section 4 3 contains the wing pre flight inspection checklist while AOI Section 4 5 contains the base and engine pre flight checklist 9 3 Aircraft Operation Aircraft operation information is contained in AOI Sections 4 8 and 4 9 Section 4 8 covers normal flight operations in checklist form while 4 9 describe those procedures in detail 9 4 Startup See AOI Sections 4 8 and 4 9 1 2 for engine start up details The master switch should be turned on keyed switch on the panel then depress the Skydat o
101. or air sports The standard prescribes tests for penetration resistance shock absorbing properties field of vision and head mobility 4 9 Normal Procedures Check List The following checklists should be used as a reference More detailed procedures are found in the Amplified Procedures section which follows Prior to flight a thorough pre flight inspection of the aircraft should be carried out Details of the pre flight inspection are shown earlier in this section August 2009 Issue 2 2 Page 29 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT912 4 9 1 Before Starting Engine Pre flight Inspection Full free movement of the wing when attached to the trike base Passenger Briefing oafety Belts Helmets Intercom Connection Brakes Intercom Connection Parachute if fitted Completed Completed Completed secure Secure Secure On Park Secure Remove Safety Pin Table 8 Section 4 Before Starting Engine Check 4 9 2 Starting Engine Park Brake Fuel Cock Hand and Foot Throttle Key Instrument Ignition Choke Propeller Depress Start Button Oil Pressure Choke Engine Running On Open Off Idle Position Clear Push When engine fires Release Check 2 Bar 30psi within 10 secs Off Adjust Idle to 2000 rpm 2 mins Table 9 Section 4 Starting Engine Check August 2009 Issue 2 2 SECTION 4 NORMAL PROCEDURES Page 30 SECTION 4 NORMAL PROCEDURES Air
102. ot exceed 300 rpm Both ignitions should be in the on position and ignition two should be turned off and the RPM drop should not exceed 300 rpm Ensure both switches are in the on position after ignition circuit testing During take off and landing the recommended trimmer setting is in the fast trim position It is acceptable to set the trim as far as mid trim position for take off and landing The trimmer decal on the control frame upright adjacent to the trimmer knob indicates the trim position August 2009 Issue 2 2 Page 35 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT912 SECTION 4 NORMAL PROCEDURES 4 9 14 Take Off AirBorne trike wings have a neutral static balance allowing a safe take off that is controllable under all suitable flying conditions Take off should be made on full power with only the foot activated throttle used during take off The take off run is the measured ground distance covered until the aircraft reaches a height of 50 feet above the average elevation of the runway used Refer to Section 5 for details of take off performance During the take off run the wing should be held in the trim position with the wings level Accelerate smoothly to the take off safety speed If the aircraft is fully loaded you will require full power When the aircraft reaches the take off safety speed the control bar should be pushed steadily forward until the trike lifts and rotates quickly on the main wheels A
103. owering each wing to within 10 cm off the ground on ground level 2 6 4 Flight Load Factor Limits Max positive manoeuvring load 4 0 G factor Negative load factors Prohibited Load factors below 1 0 G To be avoided Table 7 Section 2 Flight Load Factor Limits 2 6 5 Flight Crew Limits Minimum flight crew is 1 person front seat August 2009 Issue 2 2 Page 7 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 6 6 Kinds of Operation Limits The aircraft is only to be flown under visual flight rules VFR and the minimum equipment required to operate under VFR conditions are an air speed indicator altimeter and instruments required by the engine manufacturer In Australia when operated at a public aerodrome or on a cross country flight a compass and reliable time piece are required Additional equipment may be required for some overseas operations 2 6 7 Fuel Limitations Maximum Usable Fuel 67 litre 17 7 US Gal Unusable Fuel capacity 3 litre 0 8 US Gal Sump Capacity 500 ml 0 13 US Gal Table 8 Section 2 Fuel Limitations CAUTION SIGHT GAUGE 10 LITRE GRADUATIONS INDICATE TOTAL FUEL NOT USABLE FUEL ZERO USABLE FUEL IS INDICATED WHEN THE FUEL IS LEVEL WITH THE BOTTOM OF THE SIGHT GAUGE 2 6 8 Maximum Passenger Seating Limits One passenger maximum allowed 2 6 9 Minimum Pilot Weight The microlight aircraft must only be flown solo from the front seat Minimum pilot wei
104. pension Range Dimension Dimension Measured from the line joining the leading Imperial Metric edge nose bolts to the suspension point SST WING 49 80 inch 0 8 1265 mm 20mm STREAK III CRUZE WING 48 6 inch 0 8 1235 mm 20mm MERLIN WING 50 2 inch 0 98 0 8 1275 mm 25 20mm otreak Cruze Middle U bracket hole only Merlin rear U Bracket permitted for aerotow MTOW Table 6 Section 2 Centre of Gravity Limits NOTE The rear hole on the wing suspension bracket on the SST Streak and Cruze wing has been blanked off so that it cannot be used Using the rear hole was found to show non compliance to the minimum required trim speed of 1 3 Vs 2 6 2 Manoeuvring Limits All aerobatic manoeuvres including spinning is prohibited Aerobatic manoeuvres including whipstalls stalled spiral descents and negative manoeuvres are not permitted It must be emphasised that a whipstall spiral descent or negative G manoeuvre can never be conducted safely These manoeuvres put the aircraft outside the pilots control and put both the aircraft and its occupants in extreme danger Do not pitch nose up or nose down more than 45 degrees from the horizontal The front support tube of the trike and the pilot s chest limits the fore and aft movement of the control bar respectively 2 6 3 Bank Angle Do not exceed 60 degrees of bank angle In roll there is no stop for the control movement For the purpose of pre flight freedom check by l
105. perators Manual Section 10 2 3 Lubricants In general use only synthetic or semi synthetic oil API classification SF or SG or later quality oils Mulitigrade is recommended These oil types are detergent types Oil Capacity 3 litres maximum 2 litres minimum consumption 0 06 litres hr maximum Two oils which are recommended by the Rotax Service instruction 18 UL 97 for use with both Avgas and unleaded fuels are SHELL Advance VSX 4 APISG SAE 15W 50 VALVOLINE Dura Blend Synthetic APISJ SAE 10W 40 2 4 5 Cooling System WARNING DO NOT OPEN THE COOLING SYSTEM WHEN THE ENGINE IS HOT SEVERE SCALDING AND OTHER INJURIES MAY RESULT Water cooling system capacity is 2 5 litres See maintenance manual for further details Coolant Specification A MANDATORY Rotax Directive was issued on the 25 of November 2004 which requires a change in the type of coolant that must be used with the Rotax 912 type engine From the 23 Feb 2005 the new coolant Evans NPG waterless coolant is to be used The reason for the change is In some instances conventional coolant mixture ratio of 50 water and 50 antifreeze can vaporize or boil before the maximum permissible cylinder head temperature is reached Rotax Service bulletin SB 912 043 pg 1 Earlier Airborne trikes have had a silicate free type high quality and long life antifreeze coolant which is red Airborne Part Number 106644 installed in the radiator This coolant must b
106. red flight path September 2008 Issue 2 1 Page 6 AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY 3 3 12 2 Nose Down Attitude To recover from the situation where the nose of the aircraft is pitched down more than 45 degrees from the horizontal proceed as follows Raise attitude push Out P Apply Power R Recover from dive and Resume desired flight path 3 3 13 Instrument Failure Instrument failure may occur through an electrical fault or through exposure to High Intensity Radio Fields HIRF The aircraft is equipped with an analogue ASI as well as a digital engine management system The analogue ASI will not be effected by either an electrical fault or HIRF If there is a problem with the digital system the correct procedure is to fly to the nearest safe landing area and investigate the cause of the malfunction September 2008 Issue 2 1 Page 7 AirBorne WindSports Pty Ltd SECTION 3 Aircraft Operating Instructions Edge XT 912 EMERGENCY This page left blank intentionally September 2008 Issue 2 1 Page 8 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT912 SECTION 4 NORMAL PROCEDURES NORMAL PROCEDURES NORMAL PROCEDURES 1 4 NORMAL PROCEDURES 4 4 1 General 4 4 1 1 XT 912 SST Speeds for Normal Operation 4 4 1 2 XT 912 Streak 3 Speeds for Normal Operation 4 413 XT 912 Cruze Speeds for Normal Operation 5 41 4 XT 912 Merlin Speeds for
107. rial Conversion Factors August 2009 Issue 2 2 Page 10 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 LIMITATIONS LIMITATIONS 2 LIMITATIONS 2 1 General 2 2 Airspeed Limitations 2 3 Airspeed Indicator markings 2 4 Power Plant Limitations 2 4 1 2 4 2 2 4 3 2 4 4 2 4 5 2 4 6 2 4 7 Engine Engine Limitations Fuel Grades Lubricating Oil Cooling System Propeller Engine Instrument Markings 2 5 Weight Limits 2 6 Operational Limits 2 6 1 2 6 2 2 6 3 2 6 4 2 6 5 2 6 6 2 6 7 2 6 8 2 6 9 2 6 10 Centre of Gravity limits Manoeuvring Limits Bank Angle Flight Load Factor Limits Flight Crew Limits Kinds of Operation Limits Fuel Limitations Maximum Passenger Seating Limits Minimum Pilot Weight Other Limitations 27 Placards 2 7 1 2 7 2 2 7 3 2 7 4 2 7 5 Flight Limitations Placard Dash Placard Locations Aircraft Operating Instructions Placard applicable for LSA Wing Vne ASI Placard Wing Trimmer Operation Placard Trimmer Placard Location Fuel Capacity Placard Fuel Tap Placard Hand Throttle and Ignition Placard Pilots Right Seat frame Placard Choke Placard Mast Block Placard Locations Pilots Left Seat frame Placards Earth Placard Circuit Breaker and Power Socket Placard Oil Tank Capacity Placard No Step Placard Step Placard otep and No Step Placards Clear Prop Placard Shock Absorber Pressure Placard Right Hand Suspension Strut Placards King Post Placard Aug
108. rminate at the right hand side of the mast block A 5A fuse is to be used for the radio and intercom power supply The fuse holder is marked with the correct Current rating for the fuse August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE 3 The battery charging circuit is protected with a 20A fuse which also terminates at the right hand side of the mast block The fuse holder is marked with the correct Current rating for the fuse A 10 Amp circuit breaker is located on the right hand side of the dash The circuit breaker protects the dash instrumentation and the DC socket 8 12 1 Wing Daily Maintenance If the wing is assembled and disassemble on a frequent basis the batten latch fittings should be checked for security during assembly Latch fittings should be sharp and not rounded Rounded edges can occur from unloading without depressing the latch Check the unloaded measurement of latch to body of the outer fitting is not less than 2mm to maintain loaded retaining force oection 57 10 00 of the wing maintenance manual has further details if fittings are out of tolerance WARNING ALWAYS ENSURE THE BATTEN END FITTINGS ARE CLOSED AND LOADED SECURELY BEFORE TAKE OFF BATTEN ENDS BECOMING UNLOADED DURING FLIGHT AT HIGHER AIRSPEEDS MAY HAVE SERIOUS EFFECTS ON THE FLIGHT PERFORMANCE AND STABILITY CHARACTERISTICS OF THE WING August 2009 Issue 2
109. rsection of the pilots weight versus the passenger weight plus additional weight this gives the maximum amount of fuel to be used without exceeding the MTOW 6 3 3 Metric Fuel Calculator Imperial Metric Occupante110 kg Rear Additional Front Occupant kg UNIT CONVERSION B 80 85 90 95 Gallons US 0 2642 walo Loy Pr Irma n ee ojos Ip Ja 1 7 4 r 2 nuca F 2 Pa to 2 Oo Od on Oo CTT Oo oy Pa 7 4 m I 4 oo PRs Oo eee E 1 lIll X lIlLX llx OO 4 en co 1 cn f Fe 2 in co co e ral ea c Fuel capacity TOL subjectto M TOW ky 450 Payload ky 223 Empty weight 227 I Inuseahble fuel L 3 Additional equipment eq BRS of 1Ukg 53 4B 53 46 39 11 25L 73 minutes useable fuel at full power Example Pilot 75kg 10kg additional equipment Passenger 100kg BOL fuel Table 6 Section 6 Metric Fuel Calculator August 2009 Issue 2 2 Page 5 AirBorne WindSports Pty Ltd SECTION 6 Aircraft Operating Instructions Edge XT 912 6 3 4 Imperial Fuel Calculator Airborne XT 912 Series Aircraft Fuel Volume Calculator Imperial US Rear Occupant 20 Ib Additianal Equipment Rear Occupant Front Occupant 120 130 140 150 160 170 180 190 200 210 Table 7 Section 6 Imper
110. s installed 4 5 6 Attach Trimmer To Mast SST only Connect trimmer to wishart clip on the mast Ensure it is threaded through the pulley on the keel first Figure 31 Section 4 Attach Trimmer to Mast 4 5 7 Remove Keel Extension Disengage the brake of the trike lift the nose of the wing to allow the front wheel to be rolled rearward over the control frame so that the base bar is forward of the cockpit Re engage the brake Remove the keel extension by removing safety ring and pulling out the clevis pin Remove keel extension Store with pack up gear Figure 32 Section 4 Remove Keel Extension 4 5 8 Rotate Wing Go to the nose of the wing and with the mast brace tube in one hand and the control bar in the other lift the base bar Rotate the wing until the rear of the keel rests on the mast In strong winds maintain a firm grip on the wing Figure 33 Section 4 Rotating Wing August 2009 Issue 2 2 Page 22 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 5 9 Insert Mast Lever Insert the lever so that the flat section is facing toward the mast E 4 5 10 Attach Mast Brace Bring mast brace into position and allow the outer sleeve to slide into position Install the top pip pin and cap Install lower pip pin and cap Figure 34 Section 4 Insert Mast Lever 4 5 11 Load Mast Lever Once the lever is located correctly rotate the lever down 180
111. s the aircraft leaves the ground the control bar must be eased back to maintain take off safety speed CAUTION Maintain your engine in top condition and assume its going to stop running at any time Leave yourself a way out for an unexpected engine failure HIGH ANGLE CLIMB OUTS NEAR THE GROUND SHOULD BE AVOIDED Never fly your aircraft at locations airspeeds altitudes or under any circumstances from which a successful engine off landing cannot be attempted 4 9 15 Climb Initial climb out should be made on full power for maximum take off weight Approximately 2 3 of maximum take off power is considered comfortable WARNING AT LOW ALL UP WEIGHTS THE TAKE OFF CLIMB OUT AT THE TAKE OFF SAFETY for a minimum weight take off Take off distance i SPEED CAN RESULT IN HORIZONTAL PITCH will be extended at reduced power INCLINATIONS IN EXCESS OF THE PLACARDED 45 DEGREES MAXIMUM THE PILOT MUST BE AWARE OF THIS AND SHOULD KEEP WITHIN THE PLACARDED LIMITATIONS BY LOWERING THE ATTITUDE OR REDUCING ENGINE POWER Once climb is established power should be reduced to below maximum continuous power of 5500 rpm A minimum of take off safety speed should be used At this speed the aircraft would round out nicely into a glide should the engine fail Avoid pitching the nose of the wing up more than 45 degrees to the horizon Very steep climbs are dangerous and can result in a stall followed by a severe pitching of the nose forw
112. ssible and you must be able to operate them instinctively without hesitation The primary throttle control is foot operated and complemented by the hand throttle forward for full power and rearward for power off The ignition switches are on the right hand side of the seat frame forward for on and rearward for off Never run the engine on the ground with the propeller turning unless you are doing so in a run up area and can observe anyone or anything entering the danger area It is recommended that the engine not be run for any long periods whilst stationary WARNING on the ground Possible damage to the engine LOCK THE WHEEL BRAKE TO REDUCE ANY may occur due to overheating of the engine fluid POSSIBILITY OF DANGER TO ANY PERSON S DURING ENGINE STARTING Before starting your engine you should read and be familiar with the engine manual Run through the following checklist pronounced twimpfish prior to starting the engine for each and every flight T Throttle full and free movement Tyres inflated and serviceable W Wind check direction and strength Wires secure and airworthy Mixture chokes off P Pins fitted and secured F Fuel On and sufficient Instruments check set and operational S Switches ignition check all switches on C Controls pitch and roll full and free movement Chocks removed secured in aircraft H Harness and Helmet in place and secure Remember that the pilot in command has
113. supplied with the wing must be used to prevent chaffing during transport Supports should be softly padded and any support systems used for transport such as roof racks must use attachment straps that are sufficiently secure to eliminate the possibility of damage from vibration and movement Avoid damage to your wing by using well padded racks As the wing is quite heavy a strong set of racks are required Flat straps should be used for tie downs to avoid damage to leading edge Mylar When transporting the trike base the use of trike and prop covers to protect your aircraft from road grime and idle fingers is recommended Tie the propeller to the trike to stop it from rotating at speed Check that the back of the wing is well clear of the front mast with the trike on the trailer Remember that you have an overhanging load when manoeuvring in tight places otore the wing in a dry room off the ground air the wing out regularly to avoid mildew and never store wet oee your Rotax Manual for precautions to be observed if you intend to store the aircraft without use for extended periods 4 14 Noise Characteristics The Edge XT 912 has been certificated to UK Air Navigation Environmental Standards Order 2002 schedule 3 for two seat microlight aeroplanes Noise levels were recorded at 78 2 dB A Airservices Australia have found compliance to CAO 101 55 with resultant noise levels of 62 7 dB A August 2009 Issue 2 2 Page 53 AirBorne
114. swind landings or take off with low wind components up to 8 knots are quite safe and controllable even to the inexperienced pilot The nominated approach speed should be increased by 5 knots when landing in cross wind conditions of 10 knots or more August 2009 Issue 2 2 Page 37 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES After touchdown in cross wind conditions the relative airflow over the wing will become increasingly span wise from tip to tip as the aircraft slows down The upwind wing tip should be lowered slightly the amount depends on the wind strength and the undercarriage wheels will retain firm contact with the ground Take off procedure is unchanged for the nominated crosswind limit The upward wing may need to be lowered at the start of the take off procedure in higher cross winds 4 9 20 Baulked Landing During a situation where a baulked landing go around is required normal take off power and procedures should be used 4 9 21 Stopping the Engine To stop the engine after a period of running the ignitions should be switched off at idle Switching off at high RPM floods the engine and makes restarting difficult If the engine has been running under full power allow the engine to cool at idle before switching off 4 10 After Landing Securing After landing and when in the parking area apply parking brake and lock Switch the ignition Electrical switch a
115. t Panel 7 7 Undercarriage System The microlight uses a tricycle undercarriage with a braking system via a nose wheel drum brake unit Oil dampened front shock absorbers are used The rear suspension is a swinging wish bone design in conjunction with a 45mm compression strut which houses an oil pneumatic shock absorber August 2009 Issue 2 2 Page 3 AirBorne WindSports Pty Ltd SECTION 7 Aircraft Operating Instructions Edge XT 912 AIRCRAFT amp SYSTEMS 7 8 Seat Adjustment The front seat backrest on the Edge XT trike has a simple for and aft adjuster on the base tube To adjust the seat backrest forward the following procedure should be adopted 1 Remove pin and bolt from channel 2 Rotate seat back forward and replace bolt in channel one hole further forward 3 Replace safety pin through bolt To move backrest rearward the bolt should be moved one hole back 7 9 Occupant Restraint Harness Both front and rear seats are fitted with a 3 point restraint harness system The shoulder inertia reel system is fitted to the mast and requires attachment on the male section of the lap belt during lap belt fastening see photo When flying the trike solo it is important to fasten the rear seat belt to prevent contact with hot engine components in flight Figure 2 Section 7 Restraint harness shoulder sash amp buckle fitting 7 10 Engine The power unit is a Rotax 912 UL 80hp 4 stroke engine designed and built in Austria T
116. t both nose battens tail end first Locate the front of the batten on the alloy stubs on the front of the keel tube Figure 21 Section 4 Locate Nose Battens August 2009 Issue 2 2 Page 14 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 3 11 Install Nose Fairing Attach the nose fairing by applying the top Velcro first then gently tension over the nose plates and attach the Velcro to the undersurface Figure 22 Section 4 Install Nose Fairing 4 3 12 Place U Bracket Padding Inside Sail Place the U Bracket padding inside the sail and zip up the undersurface Figure 23 Section 4 Place U Bracket Padding Inside Sail 4 3 13 Insert Remaining Main Sail Battens Remove tip bags Insert remaining main sail battens at the tips 4 3 14 Insert Undersurface Battens The undersurface battens should be inserted as far as possible without forcing them The batten should then be pushed with your thumb so that the end is inside the pocket Use the string to pull the batten back to the rear of the pocket Figure 24 Section 4 Insert Remaining Sail Battens August 2009 Issue 2 2 Page 15 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 3 15 Load Inboard And Outboard Sprogs Inboard sprog Outboard Figure 25 Section 4 Load Sprogs Load the inboard and outboard sprogs by guiding them into the inside of each p
117. table pitch The hub is anodised alloy Two alternate propeller hub configurations are available for use on the XT912 these include Warp Drive 3 Blade with Warp Drive hub 67 7 inches 172 cm diameter Bolly BOS3 68 x 58 left hand version with BOS 3 hub 66 inches 167 6 cm diameter Drive Ratio 912 UL Bolly 243 12 912 UL Bolly 227 9 912 UL 912 UL Warp Drive 227 9 Table 1 Propeller pitch and gearbox ratio table The gear set part number stamped on the gearbox housing corresponds to the gearbox ratio at time of manufacture Note that replacement gears are available to change the ratio within the gearbox l Rotax Gear Set Gearbox Ratio Bart Niger 2 27 996 605 Table 2 Rotax Gear Set Part Numbers The propeller pitch setting and checking procedure is outlined in the Base Maintenance Manual The pitch setting is determined as a part of certification of the aircraft Settings outside this specification have an unknown effect on aircraft performance and are not approved 7 13 Brake System A front wheel drum brake system or an optional rear wheel disk brake system is used on the aircraft Depressing the brake lever on the left hand side of the front footrest actuates the brake on aerotow equipped trikes the aerotow release is the lever on the top left painted yellow A brake lever lock is provided To engage depress foot lever and raise locking lever by hand To disengage depress the foot lever
118. the Streak 3 wing Cruze wing Merlin or the SST wing All relevant information is supplied for either configuration but please note that unless otherwise shown data for the SST is as per the Streak 3 The operator must ensure that the correct data is referenced for the particular wing base combination 1 1 Introduction This microlight series has been designed and manufactured in accordance with the ASTM designation 2317 04 Standard Specification for Design of Weight Shift Control Aircraft The aircraft has also been designed to the higher level of certification requirements for weight shift controlled aircraft The design standard of BCAR Section S has been used for certification as a primary category aircraft As an Australian Company we are proud of our range of microlight aircraft Our microlights have been developed to provide the economy and durability required to meet the exacting demands of our Australian conditions The success of our microlights is based upon a high standard of product quality innovative design engineering and exceptional standards of reliability and performance that have been established since 1983 Regular maintenance is required to keep your microlight in a safe condition Detailed maintenance requirements are outlined in the wing and base maintenance manuals Please reference these manuals to ensure your microlight is maintained correctly In the USA the FAA registers and administers Light Sport Aircraft T
119. the coolant cap which prohibits the use of water in the coolant system The coolant should be replaced according to the Rotax maintenance manual current issue Please refer to the directive which is available from the Rotax website SB 912 043 September 04 WARNING WATER OR WATER CONTAINING COOLANT MUST NOT BE ADDED IN ANY CASE TO THE COOLING SYSTEM WITH THE NEW EVANS NPG COOLANT August 2009 Issue 2 2 Page 4 AirBorne WindSports Pty Ltd SECTION 8 Aircraft Operating Instructions Edge XT912 HANDLING amp MAINTENANCE Field service Instructions If EVANS NPG coolant is not locally available temporarily top off the system with propylene glycol antifreeze and be sure not to add water Within 15 days the temporary coolant should be completely drained and the system refilled with EVANS NPG coolant Rotax SB 912 043 Pg 5 8 8 Tyre Inflation The recommended tyre inflation pressures are 13 to 17 PSI 19 to 117kPa for both the front and rear tyres When checking the tyre pressures the opportunity should be taken to examine the tyres for wear cuts bruises slippage and other defects 8 9 Shock Struts 8 9 1 Rear Shocks WARNING SPECIALISED PUMPS MUST BE USED FOR THE AIR SHOCKS PRESSURES UP TO 600 PSI EXIST The rear shocks are pressurised to 580 PSI using a schrader valve system A special pump will be necessary to repressurise the rear shocks to the correct setting There should be no reason why the rear s
120. the left side of dash Part no 106617 and 107237 are early issue parts suitable for use with the wings identified on the respective placards Series Edge XT Series Table 12 Section 2 Wing Vne ASI Placard Location August 2009 Issue 2 2 Page 11 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 5 Wing Trimmer Operation Placard 180MM 2 4 INCREASE oy ge P REDUCE gt 2 Lo TRIM SPEED SIN ke fT TRIM SPEED PART NO 103817 180MM increase J P P7 REDUCE a TRIM SPEED L ll Ly S TRIM SPEED PART NO 107241 Location The wing trimmer operation placard is located on the right side control frame down tube adjacent to the trimmer knob The placard is installed so that the Increase trim speed arrow faces downward on the down tube Series Streak 3 SST and Cruze Table 13 Section 2 Wing Trimmer Operation Placard 2 7 6 Trimmer Placard Location Reduce Trim Speed Increase Trim Speed z NOTE Ensure that the Placard is the correct orientation as shown by the text boxes beside the photograph Streak placard shown in photo Figure 2 Section 2 Trimmer Placard Location August 2009 Issue 2 2 Page 12 SECTION 2 AirBorne WindSports Pty Ltd LIMITATIONS Aircraft Operating Instructions Edge XT 912 2 7 7 Fuel Capacity Placard mm 55mm FUEL TANK CAPACITY 18 5 US GALLON FUEL TANK CAPACITY 7
121. tions Edge XT 912 LIMITATIONS 2 7 12 Mast Block Placard Locations Figure 4 Section 2 Fuel Tap Shock Absorber Pressure and Earth Placard Locations 2 7 13 Pilots Left Seat frame Placards MOHI Figure 5 Section 2 Choke Placard Location Under Seat Bag Placard in Background August 2009 Issue 2 2 Page 15 SECTION 2 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 14 Earth Placard 18mm P No 105710 The engine earth placard is located on the rear of the seat mast Location block on the left side Series Edge XT Series Table 18 Section 2 Earth Placard 2 7 15 Circuit Breaker and Power Socket Placard 72mm MASTER SWITCH CIRCUIT BREAKER OFF PUSH TO RESET EL CLEAR PROP 2mm PUSH TO START DC P No 105715 The master switch circuit breaker placard is located on the right side dash Location Series Edge XT Series Table 19 Section 2 Circuit Breaker and Power Socket Placard August 2009 Issue 2 2 Page 16 SECTION 2 AirBorne WindSports Pty Ltd Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 16 Oil Tank Capacity Placard 57mm OIL TANK CAPACITY 3 LITRES 57mm OIL TANK CAPACITY 0 8 US GALLON 20mm 20mm FOR RECOMMENDED OIL SEE PILOTS HANDBOOK P No 106648 FOR RECOMMENDED OIL SEE AIRCRAFT OPERATING INSTRUCTIONS P No 107598 Location The oil tank capacity placard is located on the oil tank on the left
122. ton should be depressed with the thumb while simultaneously pulling the pip pin out Re insert pip pin in nose channel Figure 65 Section 4 Disconnect Nose Catch and Remove Nose Cone 4 12 9 Undo Strut Bolts at Leading Edge Remove the safety pin and wingnut from the connecting bolt Gently move the leading edge forward or rearward to take any weight off the bolt and slide it out Replace the bolt wingnut and pin into the strut Repeat for the other side Figure 66 Section 4 Remove Strut to Leading Edge Connecting Bolt August 2009 Issue 2 2 Page 47 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 12 10 Remove Control Frame Connecting Bolt Expose the control frame wingnut by moving the strut forward to be line with the downtube Remove the safety pin undo the wingnut and remove the bolt Replace the bolt in the strut once removed Figure 67 Section 4 Remove Control Frame Connecting Bolt 4 12 11 De Tension Pull Back Cable Depress quick clip with left thumb Use right hand to pull on the webbing handle The webbing handle is located underneath the sail next to the keel Remove the shackle from the quick clip block and allow webbing handle to move forward E Figure 68 Section 4 De tension Pull Back Cable August 2009 Issue 2 2 Page 48 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES
123. ts free from damage EM EM ELS Reflex bridle lines NA Cross bar tensioner routing and catch Velcro pull back cover Hang point universal bracket amp bolts Trimmer operation routing pulleys twists NI V q Control frame tubes hinges knuckles connections N Control frame cables fittings amp terminations both ends Junction cross bar amp leading edge EM lt RM NL mn NN E E EL Top rigging kingpost located NA Stuts located correctly ie Leading edge forward and on correct side gt gt oprog hinge free to pivot Wires secure All zips closed oail condition inspection tears abrasion stitching amp attachment y Sail free from water accumulation Y q General inspection of complete wing A lt Full free movement of the wing when attached to the trike base see section 4 8 1 Inspect all cables Inspect for kinks fraying corrosion particularly around the NICO press fittings August 2009 Issue 2 2 Page 18 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Table 5 Section 4 Wing Pre Flight Inspection If the wing has been left fully set up for any period then the following additional checks should be performed Extended set up Wing pre flight inspection The symmetry of the wing batten profile check All tubes straight
124. ull back system gives a mechanical advantage of 2 1 Tension until the cross bar wire shackle is located in the quick clip block behind the safety button 4 2 8 Install Pull Back Cover Ensure that the front Velcro tabs are folded back and secured to the top of the cover Figure 7 Section 4 Install Pull Back Cover 4 2 9 Attach Nose Catch The nose catch should now be attached so that the pip pin is inserted through both the nose catch and channel Ensure the pip pin cap is secure Figure 8 Section 4 Attach Nose Catch 4 2 10 Locate Nose Battens Insert both nose battens tail end first Locate the front of the batten on the alloy stubs on the front of the keel tube August 2009 Issue 2 2 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES Figure 9 Section 4 Locate Nose Battens 4 2 11 Install Nose Fairing Attach the nose fairing by applying the top Velcro first then gently tension over the nose plates and attach the Velcro to the undersurface Figure 10 Section 4 Install Nose Fairing 4 2 12 Insert Remaining Main Sail Battens Remove tip bags Insert remaining main sail battens at the tips 4 2 13 Insert Undersurface Battens otreak and Cruze wings The undersurface battens should be inserted as far as possible without forcing them The batten should then be pushed with your thumb so that the end is inside the pocket Use the string to pull the batten bac
125. undamaged and without cracks All cables undamaged no fraying with secure thimbles swages All nuts and bolts secure and locked appropriately All quick release fittings secure Universal bracket undamaged heart bolt and back up strap secure oail tension settings correctly aligned and symmetrical Battens undistorted and in good condition All sail seams intact with no frayed stitching No tears or nicks in the sail REM lt lt Trimmer functional and wires not damaged Table 6 Section 4 Extended Wing Pre flight 4 5 Attaching Wing to Base WARNING THE TRIKE MAST IS FITTED WITH A GAS STRUT TO ASSIST LIFTING THE WING NEVER ALLOW THE MAST TO BE UNLOADED TOO QUICKLY HANDS OR OTHER FOREIGN OBJECTS WILL BE SEVERELY DAMAGED IF CAUGHT BETWEEN THE MAST AND SEAT ENGINE BLOCK 4 5 1 Attach Mast Retaining Strap mpi The mast has a gas assist strut to assist lifting the wing when the mast is raised To hold the mast in position for wing attachment the mast retaining strap should be routed around the rear steering bracket and over the mast The strap can be adjusted to pull the mast down to the correct height te Sr 7 Figure 27 Section 4 Attach Mast Retaining Strap August 2009 Issue 2 2 Page 19 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES August 2009 Issue 2 2 Page 20 AirBorne WindSports Pty Ltd SECTION 4 Aircra
126. ure 1 Section 4 Assemble Control Frame Optional If training bars are to be fitted to the control frame follow this procedure The fitment of the left hand side training bar is illustrated showing the correct attachment of the bar on the inside of the control frame The detail view shows the sequence of components 1 Bolt head to the inside of the control frame 2 Tube 3 Nylon Washer 4 Down Tube Clamp both sides 5 Wing Nut turned until both side of the down tube clamp contact Ensure the training bars are held securely 6 Safety Pin Note The attachment to the base bar a pip pin or bolt secures the training bar to the base bar and also secures the control frame knuckle A longer PIP pin is necessary for the larger diameter tube of the training Bar The welded base bar attachment has been made to be slightly loose for ease of fitment The right hand side training bar is secured in the same way and is also on the inside of the control frame Figure 2 Section 4 RHS Training Bar Attachment August 2009 Issue 2 2 Page 7 AirBorne WindSports Pty Ltd SECTION 4 Aircraft Operating Instructions Edge XT912 NORMAL PROCEDURES 4 2 3 Stand The Wing Up Rotate the control frame to the vertical position so that the wing is resting on the control bar Do not attempt to connect the nose catch now Remove the glider bag and unclip all the wing straps Figure 3 Section 4 Stand the Wing Up 4 2 4 Spread Leading
127. ust WARNING un AT FULL ENGINE REVS THE TIP OF THE C Maintain Control PROPELLER IS SPINNING AT SPEEDS IN T Throttle closed EXCESS OF 650 KILOMETRES PER HOUR EVEN SMALL OBJECTS CAN CAUSE F Fuel tap off SIGNIFICANT DAMAGE THE Ignition off PROPELLER L Forced Landing This problem may be avoided if precautions are taken prior to take off Inspect the strip or ground you are to use as your take off area for sticks rocks or any debris that may be flicked up by the tyres and sucked through the propeller Ensure that all items carried by occupants such as cameras and sunglasses are secured so they are not able to come loose and pass through the propeller 3 3 8 Sail Damage If you encounter damage to the sailcloth during flight the first procedure is to maintain control of the aircraft If the sail damage is not impairing the flight characteristics of the aircraft land at the nearest landing field to inspect the damage 3 3 9 Emergency Parachute The emergency ballistic parachute can be fitted as an option The parachute operating handle is fitted with a safety pin This pin should be removed before each flight and the safety pin must be replaced before the pilot alights from the aircraft A force of approximately 15 20 kg pull on the actuating handle is required to activate the BRS rocket motor The parachute is only to be used in emergency WARNING situations as a last resort and when you are certain IT IS IMPORTANT TO REA
128. ust 2009 Issue 2 2 SECTION 2 LIMITATIONS WDAWAAAWDONNNNNN O OOTDAAKA A O W O Q n Page 1 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 7 24 Wing and Base Data Plates 20 2 25 Emergency Parachute 21 2 7 26 Emergency Parachute Placard Location 21 2 2 Emergency Parachute Warning Placard 22 2 28 Under Seat Bag Placard 22 August 2009 Issue 2 2 Page 2 AirBorne WindSports Pty Ltd SECTION 2 Aircraft Operating Instructions Edge XT 912 LIMITATIONS 2 LIMITATIONS 2 1 General The limitations section of this AOI outlines the various operating limitations instrument function and placards necessary for the safe operation of this aircraft engine and standard equipment 2 2 Airspeed Limitations 2 2 0 1 XT912 Streak and XT912 STT Speed KIAS KCAS Comments Never Exceed 85 knots 74 knots Do not exceed this speed in any Speed V operation Maximum 80 knots 70 knots Do not make full or abrupt control Manoeuvring movements above this speed Speed Va Table 1 Section 2 Airspeed Limitations 2 2 0 2 XT912 Cruze Speed KIAS KCAS Comments Never Exceed 73 knots 65 knots Do not exceed this speed in any Speed Vne operation Maximum 73 knots 65 knots Limited by Vne Manoeuvring Speed Va Table 2 Section 2 Airspeed Limitations 2 2 0 3 XT912 Merlin Speed KIAS KCAS Comments Never Exceed 66 knots 59 knots Do not exceed this speed in any Speed Vne operati

AIRCRAFT OPERATING INSTRUCTIONS Light

Contents

Download Pdf Manuals

Related Search

Related Contents