operating instructions
Contents
1. may cause damage to the appliance and or user DO NOT allow children to play with this appliance This appliance is not intended for use by children or infirm persons without supervision This unit is intended for indoor use only ENERGY SAVING TIPS DO NOT conduct repairs on this unit It has been built in accordance with relevant safety and performance Standards An electrical specialist must carry out all repairs ALWAYS ensure that the fan is Switched off before removing the guard ALWAYS unplug the unit from the mains before maintenance or cleaning ALWAYS use the switch on the control panel to start and stop the unit ALWAYS keep a clearance of at least 200mm from walls furniture and curtains ALWAYS turn off and unplug the unit when not in use This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be Supervised to ensure that they do not play with the appliance Do not locate the fan where furniture or other objects can obstruct the air flow Keep blinds curtains closed during the sunniest part of the day Close the fireplace damper floor and or wall registers so cool air does not escape through the chimney or duct work IDENTIFICATION Ou2. Adjustment Fastener Base Cover Base Weight Pole ASSEMBLY 4 Remove the 2 pole screws from the motor connector place the motor connector into the inner pole and secure into position by replacing pole screws and tightening securely Figure 5 Motor Connector 6 Inner Collar DT Pole S ole Screws hae 5 Remove the 4 screws and washers located on the front of the motor unit Place the rear grille into position on the motor unit handle up then secure in position with the 4 screws and washers provided Figure 6 N Grill Screws _ amp Washers Rear Grille 6 Place the fan blade onto the motor shaft aligning the flat on the shaft with the fan blade screw Securely tighten the fan blade screw Figure 7 Fan Blade iN f wif N Screw PKIN NAC AN Saami lt lt lt j k Hil Fan Blade 7 After loosening remove the fixing screw and nut from the front grille Place the front grille over the rear grill press grille retaining clips into position then tighten grille fixing screw and nut Ensure that the fan blade is completely enclosed and the complete grille is securely in position Figure 7 Front Grille Grille Retaining Clips 6 Grille Fixing Screw amp Nut OPERATION Make sure that you read all of the safety warnings before you operate this unit for the first time Plug the unit to a standard ma
3. CARE AND MAINTENANCE 1 Always disconnect the cord from 4 Avoid the use of gasoline benzine the electrical outlet when cleaning thinner etc as they may result in your fan damage to the fan 2 Light accumulated dust may be re moved trom the fan with a soft cloth or vacuum cleaner using the dusting brush attachment 5 Store the fan in a clean dry place when not in use Warning Do not immerse the fan in water or allow water to drip into the 3 Wipe the exterior surfaces of the fan interior of the fan housing as this could occasionally with a cloth moistened create a fire or electric shock hazard not dripping wet with a mild soap solution Dry the case thoroughly with a soft dry cloth before operating the fan WARRANTY Arlec guarantees this product in accordance with the Australian Consumer Law Arlec also warrants to the original first purchaser of this product you from a retailer that this product will be free of defects in materials and workmanship for a period of 12 months from the date of purchase provided the product is not used other than for the purpose or in a manner not within the scope of the recommendations and limitations specified by Arlec is new and not damaged at the time of purchase has not been subjected to abuse misuse neglect or damage has not been modified or repaired without the approval of Arlec and has not been used for commercial purposes Warranty If you wish to claim on the W
4. arranty you must at your own expense return the product and provide proof of original purchase and your name address and telephone number to Arlec at the address below or the retailer from whom you originally purchased the product within 12 months from the date of purchase Arlec will or authorise the retailer to assess any claim you may make on the Warranty in the above manner and if in Arlec s reasonable opinion the Warranty applies Arlec will at its own option and expense or authorise the retailer to replace the product with the same or similar product or repair the product and return it to you or refund the price you paid for the product Arlec will bear its own expenses of doing those things and you must bear any other expenses of claiming on the Warranty The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to which the Warranty relates Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure ARLEC Arlec Australia Pty Ltd ACN 009 322 105 Arlec gives the Warranty Arlec s telephone number address and email address are Customer Servi
5. ce 03 9982 5111 Building 3 31 41 Joseph Street Blackburn North Victoria 3130 Blackburn North LPO PO Box 1065 Blackburn North 3130 Email custservice arlec com au CPINO02693 50cm APF 107 HIGH PERFORMANCE J wi WWW HW l R iN A ji j N A i I co KA OPERATING i R W zuse Unni INSTRUCTIONS m SKS y N Wp dip SSH i Dai IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY SAFETY INSTRUCTIONS DO NOT use this unit for functions other than those described in this instruction manual DO NOT tilt the unit Always keep it upright Position it on a flat and Stable surface where it cannot be easily knocked over Take extra care when operating DO NOT connect the unit unless it completely assembled DO NOT use the unit in a wet room such as a bathroom or laundry DO NOT touch the unit with wet hands or feet DO NOT use the unit in the presence of inflammable substances or vapour such as alcohol insecticides petrol etc DO NOT use the mains plug to start and stop the unit DO NOT pull the supply cord or place it near a heat source Always unwind the cord completely to avoid overheating If the supply cord is damaged it must be replaced by the service agent or a similarly qualified person in order to avoid a hazard DO NOT insert or allow foreign objects to enter the grille openings as this
6. ins socket and turn on the mains switch Off Speed Switch 1 Turn the rotary switch on the top of the motor unit to select between fan speeds O OFF 1 2 or 3 O Off 1 Low Speed 2 Medium Speed 3 High Speed Figure 8 Oscillation Control 2 Push the oscillation knob downward to allow the motor unit to oscillate horizontally through approximately 90 angle Lift oscillation knob upward to turn off oscillation mode Figure 9 Vertical Direction of Motor Unit 3 The vertical direction of the motor unit can be adjusted by tilting the complete head unit incorporating motor unit and assembled grille forward or back ward until the desired direction is reached Note that stepped positions are obtained within the neck locating mechanism of the motor connector Figure 10 Height Adjustment 4 The fan height can be adjusted by loosening the height adjustment fastener lifting the inner pole with attached motor unit and then tightening the height adjustment fastener when the desired height is obtained Figure 10 Tighten amp A Loosen 5
7. ter pedestal pole Base Base Cover Off Speed switch Height adjustment fastener 1 2 3 4 Inner pole 5 6 7 Front grille 8 Fan blade 9 Rear grille 10 Carry handle 11 Motor unit 12 Oscillation control f N i 1 ti i NALD iil I Fi rv 1 f EXPLODED DIAGRAM N aA a oss Base fixing device Base fixing washer Base weight fixing nuts Base weight Pole screws Rear grille screws and washers Grille fixing screw amp nut Fan Blade Screw APF107 220 240V a c 130W 1 Remove all the sub assemblies Place the base fixing device through from the box the base fixing washer into the outer pole Fig 3 ensuring that the assembled base is stable 2 Place the base weight fixing nuts into the holes at the bottom of the heavy weight Fig 1 Figure 3 Figure 1 7 Base Fixing Washer Base Weight l Base Fixing Jj Device Base Nuts 3 After loosening the height adjustment fastener and removing it from the outer pole slide the base cover onto the base of the outer pole Replace and secure the height adjustment fastener into position again Now the assembly of the fan base with pole has been completed Place the base weight fixing screws one by one through the holes in the outer pole flange and base making sure that all of the screws holes and nuts are aligned before tightening Fig 2 Figure 2 Figure 4 Pole Screws t Height
Download Pdf Manuals
Related Search