Home

SHORT INSTALLATION AND OPERATING INSTRUCTIONS FOR

image

Contents

1. OLI SHORT INSTALLATION AND OPERATING INSTRUCTIONS FOR VIBRATORS Section 0 DESCRIPTION MVE electric vibrators are designed and constructed in accordance with the following applicable standards CEI EN 60034 1 EN 61241 0 EN 61241 1 Conformity to Directive 94 9 CE according to category3D and to Directive 2006 42 CE UL 1004 UL 1836 CSA 22 2 N 25 CSA 22 2 N 100 CSA 22 2 N 145 The general features of the MVE series of electric vibrators are listed below Insulation Class F Standard tropicalization Protection IP 66 TENV NEMA 4 Operating temperature 20 C to 40 C Section 1 GENERAL REGULATIONS Read these instructions carefully before using the equipment and keep the manual in a safe place for future reference On receiving the product please check that The packing is not damaged to such an extent as to have damaged the product There is no external damage to the product The electrical supply corresponds to the order specifications non compliance and or external damage if any must be reported immediately in detail to the forwarding agent and the manufacturer and or dealer Section 1 1 IDENTIFICATION The vibrator s type and other various data are embossed on the identification plate This information must always be stated when requesting spare parts or a technical intervention Section 1 2 USE OF THE VIBRATOR WARNING It is forbidden to operate the motor vibrators described in this
2. costruiti in accordo con la direttiva 2006 42 CE E SUCCESSIVI EMENDAMENTI Questi prodotti non devono essere messi in servizio finch la macchina finale in cui devono essere incorporati non stata dichiarata conforme se del caso alle disposizioni della presente Direttiva Ai sensi dell allegato II B della direttiva Macchine 2006 42 CE sono applicati e rispettati i seguenti requisiti essenziali di sicurezza e di tutela della salute 1 1 1 Definizioni 1 3 4 Rischi dovuti a superfici spigoli ed angoli 1 5 4 Errori di montaggio 1 7 2 Avvertenze in merito ai rischi residui 1 1 2 Principi di integrazione della sicurezza 1 3 7 Rischi dovuti agli elementi mobili 1 5 5 Temperature estreme 1 7 3 Marcatura delle macchine 1 1 3 Materiali e prodotti 1 3 8 Scelta di una protezione contro i rischi dovuti 1 5 6 Incendio 1 7 4 Istruzioni 1 1 5 Progettazione della macchina ai fini della agli elementi mobili 1 5 7 Esplosione 1 7 4 1 Principi generali di redazione movimentazione 1 3 9 Rischi di movimenti incontrollati 1 5 8 Rumore 1 7 4 2 Contenuto delle istruzioni 1 3 1 Rischio di perdita di stabilit 1 4 1 Requisiti generali 1 6 1 Manutenzione della macchina 1 7 4 3 Pubblicazioni illustrative o promozionali 1 3 2 Rischio di rottura durante il funzionamento 1 5 1 Energia Elettrica 1 6 4 Intervento dell operatore 1 3 3 Rischi dovuti alla caduta o alla proiezione di oggetti 1 5 2 Elettrici
3. manual unless the machine or plant in which these are incorporated is declared as conforming to the provisions of Directive 2006 42 EC The electric vibrator described in this Manual is designed and tested for use in potentially explosive zones classified as zone 22 according to standard EN 61241 10 and in accordance with ATEX Directive 94 9 CE Class Il Div 2 according to article NEC 500 5 of the National Electrical Code The user must make sure that the workplace in which the electric vibrator is installed is set in safety condition from the point of view of risk of explosion To operate in safe conditions check to make sure that the dusts have an ignition temperature higher than 75K of the surface temperature indicated on the electric vibrator rating plate EN61241 10 For the Class Il Div 2 Certification the rating plate specifies the dusts groups F G and the Temperature class with which operations can be carried out NEC 500 8 The maximum temperatures indicated in this Manual and on the electric vibrator rating plate are calculated without taking into consideration the presence of layers of dust if any on the surface Its use for jobs different from those envisioned and non conform to that described in this booklet as well as being considered improper and prohibited releases the Manufacturer from any direct and or indirect liability Section 2 GUARANTEE The warranty is valid for manufacturing defects for a period of twenty four 2
4. specificati in targhetta i gruppi di polveri F G e la classedi temperatura con le quali si pu operare NEC 500 8 Le massime temperature indicate nel presente manuale ed in targa sui moto vibratori sono state calcolate senza considerare l eventuale presenza di strati dipolvere depositate sulle superfici L utilizzo dello stesso per impieghi diversi da quelli previsti e non conformi a quanto descritto in questo opuscolo oltre ad essere considerato improprio e vietato scarica la Ditta Costruttrice da qualsiasi responsabilit diretta e o indiretta Sezione 2 GARANZIA La garanzia valida contro difetti di fabbricazione per un periodo di ventiquattro 24 mesi dalla data d acquisto fa fede il documento accompagnatorio della merce La garanzia copre tutte le parti meccaniche ed esclude quelle soggette ad usura e quelle elettriche La garanzia decade e con essa ogni responsabilit diretta o indiretta qualora il prodotto sia stato manomesso o utilizzato in modo improprio siano state fatte riparazioni o modifiche da personale non autorizzato siano stati utilizzati ricambi non originali materiali resi per riparazione in garanzia vanno resi in PORTO FRANCO Sezione 3 NORME DI SICUREZZA Non vi nessuna controindicazione all uso se vengono osservate le normali precauzioni per prodotti di questo tipo unitamente alle indicazioni riportate nel manuale USO E MANUTENZIONE Il motovibratore MVE pu essere installato in qualsiasi posizione S
5. 3x24 1 2 80 58 5 8 17x30 5 8 SINGLE PHASE CONNECTION CONNESSIONE MONOFASE 5 8 17x30 5 8 60 MILLING 1 2 17x30 5 8 70 13 16 21x37 13 16 BROWN __ __ BROWN seo y2 MARRONE MARRONE MAINS cori O O BLACK BLACK _ NERO NERO 15 16 25x44 15 16 7 8 23x39 7 8 o 7 8 15 16 25x44 15 16 85 on 100 105 110 1 28x50 i 1 3 8 37x66 1 3 8 00 105 110 15 8 43x78 1 5 8 uo N ni ron iSu e e lt lt dei BLUE capacitor AZZURRO condensatore YELLOW GREEN GIALLO VERDE GREEN only USA VERDE solo USA a Soo ESEN ai MASS ADJUSTING REGOLAZIONE MASSE MVE SIZE 20 50 50 Hz SIZE 60 110 50 60 Hz MVE SIZE 20 50 60 Hz TROUBLESHOOTING CHART The vibrator doesn t work 1 No connection 1 Check mains supply 2 Mechanical block 2 Check wiring 3 Check shaft movement Increased temperature 1 Vibrating structure oversized 1 Check selelction criteria of motorvibrator and reduce weights adjustement overheating 2 Incorrect supply voltage 2 Check voltage with that on rating plate 3 Operating at room temperature 3 Restore room temperature within limits Increased noise 1 Fixing bolts slackened 1 Check locking of bolts 2 Bearing noisy 2 Re grease bearings and rep
6. 4 months from the date of purchase attested by the delivery note accompanying the goods The warranty covers all the mechanical parts and excludes electrical parts and those subject to wear The warranty will be invalidated thus freeing the Manufacturer of any direct or indirect responsibility in the following cases if the product is mishandled or used improperly if repairs or modifications are made by unauthorised personnel or if non original spare partsare used The material sent for repair under the warranty are returned CARRIAGE PAID Section 3 SAFETY STANDARDS If the customer observes the normal caution typical of this kind of equipment together with the indications contained in the manual OPERATION AND MAINTENANCE work is safe The MVE motovibrator can be installed in any position Fix the motovibrator on a sturdy surface to ensure that the vibrations induced do not cause breakage or cracks if this is not possible use plates and ribbing for reinforcement Cutting and welding procedures must be carried out by qualified personnel Suitable Hot Works like cutting welding and LOTO lockout tagout procedure for disconnecting the machine electrical and mechanical segregation must be applied for safe installation of the electric vibrator Authorization for Hot works MUST be given by specialist trained personnel familiar with the risk of explosion of powders The surface on which the machine is installed must be level and f
7. IRATE PER LATO TABELLA GUASTI E ANOMALIE Il vibratore non funziona 1 Manca il collegamento 1 Controllare rete elettrica 2 Blocco meccanico 2 Controllare cablaggi 3 Controllare possibilit movimento albero Aumento della temperatura 1 Struttura da vibrare sovradimensionata 1 Verificare criterio scelta del motovibratore e diminuire la regolazione delle masse surriscaldamento 2 Tensione di alimentazione errata 2 Controllare la tensione con i dati di targa 3 Temperatura ambiente di esercizio 3 Riportare la temperatura ambiente nei limiti nei limiti Aumento della rumorosit 1 Allentamento viti di fissaggio 1 Controllare serraggio viti 2 Rumorosit cuscinetto 2 Reingrassare il cuscinetto ed eventualmente sostituirlo OLI SpA Via Canalazzo 35 41036 Medolla MO ITALY lt gt OLI e mail info olivibra com www olivibra com WAMGROUP DICHIARAZIONE DI CONFORMITA Alle Direttive Della Comunit Europea La famiglia dei motovibratori MVE stata progettata e costruita in conformit alle direttive Direttiva ATEX 94 9CE del 23 marzo 1994 Direttiva Macchine 2006 42 CE del 17 Maggio 2006 La conformit stata verificata sulla base dei requisiti delle norme o dei documenti normativi riportati di seguito e EN 60034 1 lt EN 61241 0 EN 61241 1 C x 113 D Ex tD A22 Tx IP 66 DICHIARAZIONE DI CONFORMITA B Type Questi prodotti sono
8. THE MOTOVIBRATOR MUST BE OPERATED ONLY BY QUALIFIED PERSONNEL All the electrical components the installer intends installing in the electric vibrator such as overload protection sensors must conform to e For ATEX II 3D Certification to ATEX Directive 94 9 CE Il 3D or higher e For Class II Div 2 Certification to article 502 of NEC e For connecting the electric vibrator in equipotential connect the machine to earth using the special clamp provided on the body The environmental temperature where the machine is used is between 20 C and 40 C BLADE ADJUSTMENT Disconnect the power supply to the motor vibrator during disassembly and reassembly operations on the protection devices earth and terminal board covers After carrying out the operation on both sides refit the covers using the same screw and washers taking care to make sure the gaskets are fitted correctly in their seats as incorrect positioning can alter the degree of protection IP NEMA Section 5 MAINTENANCE The machine does not require maintenance Before carrying out any maintenance or cleaning on the machine make sure it is set in safe conditions While removing the dust that may be present on the electric vibrator take care to avoid its dispersal in the surroundings Dust deposits must never exceed a thickness of 5mm Use only a damp cloth to remove the dust Do not direct high pressure water jets on the electric vibrator All electric vibrators are lubric
9. andled by the appliance in which the electric vibrator is inserted Presence of harmful dusts Ifthe operator is required to work in the presence of harmful substance while handling the powders for carrying out routine and special operations he must use suitable protective equipment as indicated in the safety chart of the product handled by the appliance in which the electric vibrator is inserted Section 8 TROUBLESHOOTING CHART Refer to table MVE lt gt WAMGROUP ISTRUZIONI BREVI PER L INSTALLAZIONE E L USO DEI VIBRATORI Sezione 0 DESCRIZIONE motovibratori MVE sono progettati e costruiti secondo le normative vigenti CEI EN 60034 1 EN 61241 0 EN 61241 1 Conformit alla direttiva 94 9 CE secondo categoria 3D e alla direttiva 2006 42 CE UL 1004 UL 1836 CSA 22 2 N 25 CSA 22 2 N 100 CSA 22 2 N 145 Le caratteristiche generali dei motovibartori della serie MVE sono di seguito elencate Classe isolamento F Tropicalizzazione di serie Protezione IP 66 TENV NEMA 4 Temperatura di funzionamento da 20 C a 40 C Sezione 1 NORME GENERALI Leggete attentamente queste istruzioni prima di utilizzare il vibratore e custodite questo manuale per futuri riferimenti Al ricevimento del prodotto controllate che L imballo non risulti deteriorato al punto di aver danneggiato il prodotto Non vi siano danni esterni al prodotto La fornitura corrisponda alle specifiche dell ordine eventuali
10. ated by the manufacturer Electric vibrators which use ball bearing prelubricated and shielded do not require lubrication In models with roller bearings the used grease needs replacement after 5000 hours of operation if the electric vibrator is positioned horizontally and after 3000 hours of operation if it is placed vertically Electric vibrators with roller bearings are however provided with lubrication channels accessible from the outside so the user can decide to resort to periodic relubrication which must be done every 1000 hours of operation the quantity of grease required is shown in technical data sheet to be downloaded from www olivibra com Use exclusively SKF LGHP2 grease Section 6 SPARE PARTS For safety reason spare parts like complete cable condenser and capacitor must be done by OLI qualified operators For other spare parts please refer to complete manual to be downloaded from www olivibra com Section 7 RESIDUAL RISKS Mechanical hazards For maintenance operations the operator must always use personal protection devices Presence of potentially hazardous powders For carrying out routine and extraordinary maintenance operations the operators must use special personal protection devices and a mask in particular to protect the respiratory tract belonging to a Class suitable for the type of powder handled in addition to protective gloves or clothing For more details consult the safety chart of the powder h
11. etodo della rilubrificazione periodica che deve essere effettuata ogni 1000 ore di funzionamento le quantit di grasso necessario sono indicate sulla scheda tecnica del prodotto scaricabile dal sito www olivibra com Utilizzare solo grasso SKF LGHP2 Sezione 6 RICAMBI L eventuale sostituzione di cavi condensatore e pressa cavi deve essere effettuata solo da centri autorizzati OLI per garantire la sicurezza del prodotto Per le altri parti di ricambio fare riferimento al manuale completo scaricabile dal sito www olivibra com Sezione 7 RISCHI RESIDUI Pericoli di natura meccanica Per le attivit di manutenzione fatto obbligo all operatore di impiegare sempre i dispositivi di protezione individuale Presenza di polveri potenzialmente pericolose Nel caso di interventi sia ordinari che straordinari di manutenzione l operatore deve dotarsi di idonei dispositivi di protezione individuale ed in particolare utilizzare maschere a protezione delle vie respiratorie di classe idonea in base al tipo di polvere trattata nonch di guanti o indumenti Per maggiori dettagli si deve far riferimento alla scheda di sicurezza prodotto trattato dall apparecchiatura nel quale il moto vibratore inserito Presenza di polveri nocive In determinati trattamenti di polveri dove vi la presenza di sostanze nocive l operatore che dovesse accedere nel corso di interventi ordinari e straordinari deve indossare gli idonei dispositivi di protezione come i
12. he competent authorities of the area in which the operations are to be carried out e Check the mains supply voltage to ensure that it is the same as that indicated on the rating plate fixed on the motovibrator e Disconnect the line before carrying out maintenance operations or while adjusting the parts Repair and replacement of components must be done only by specialist personnel For single phase motovibrators check the condenser to ensure it corresponds with the indications on the rating plate e While connecting the motovibrator to the line the yellow green only green for USA earth cable must always be the longest to prevent it being the first to break in the event of ceding e Excessively long power cables cause voltage loss follow the instructions of the standards e Check the voltage and cycles to ensure these correspond with the values on the motovibrator rating plate When the motovibrators are installed in pairs each of these must be provided with its own external overload protection which must be interlocked in order to prevent just one motovibrator from operating when the other stops accidentally Always use magneto thermal cutout devices with delayed action to prevent these from being activated during the start up phase when the current absorbed reaches very high levels especially when the temperature is very low Overload protection shall NOT BE HIGHER than 10 of the rating plate data otherwise the warranty will be invalidated
13. i consiglia di fissare il motovibratore su una zona rigida per evitare che le vibrazioni indotte provochino rotture o incrinature se ci non fosse possibile necessario utilizzare piastre e nervature di rinforzo Le procedure di taglio e di saldatura devono essere effettuate da personale qualificato Idonee procedure di Hot Works quali taglio o saldatura e LOTO lockout tagout procedura di disconnessione della macchina segregazione elettrica e meccanica dovranno essere applicate per l installazione in sicurezza dl moto vibratore L autorizzazione all esecuzione dei lavori a caldo DEVE essere data da personale tecnico specializzato e formato sul rischio di esplosione da polveri La superficie di attacco deve essere piana planarit max 0 25mm max 0 01Inch in modo che i piedi del vibratore appoggino uniformemente e siano a perfetto contatto con la superficie di fissaggio onde evitare tensioni interne capaci di portare alla rottura dei piedi del moto vibratore Il livello di pressione acustica continua equivalente ponderata dei moto vibratori NON mai superiore ai 76 dB A Rilevazione effettuata in condizioni di normale funzionamento secondo la norma UNI EN ISO 11202 Sezione 3 1 INSTALLAZIONE Per fissare il motovibratore utilizzare bulloni qualit 8 8 dadi qualit 8 8 e rondelle piane cat A UNI6592 Utilizzare una chiave dinamometrica regolata secondo quanto riportato nella tabella dei dati tecnici Ricordarsi che la maggior parte d
14. i guasti e avarie dovuta a fissaggi e serraggi mal eseguiti Ancorare il motovibratore con adeguata catena di lunghezza cm 15 o cavo metallico alla struttura Controllare prima della messa in marcia e dopo le prime 24 ore di lavoro Alimentare il vibratore e controllare con pinza amperometrica su tutte le fasi che l assorbimento non superi il valore di targa bulloni di fissaggio del motovibratore e le saldature delle piastre e delle nervature di rinforzo Il cavo o catena di ancoraggio Il cablaggio di alimentazione Sezione 4 NOTE OPERATIVE COLLEGAMENTI ELETTRICI IL COLLEGAMENTO ELETTRICO DEVE ESSERE EFFETTUATO ESCLUSIVAMENTE DA PERSONALE QUALIFICATO E CON ALIMENTAZIONE DISINSERITA IL COLLEGAMENTO A TERRA E OBBLIGATORIO Per i collegamenti dei moto vibratori fare riferimento allo schema collegamenti elettrici La rete di alimentazione ed il collegamento dei motovibratori devono essere conformi alle vigenti norme di sicurezza stabilite dalle autorit competenti del luogo dove si svolge l attivit e Accertarsi che la tensione di rete sia la stessa indicata sulla targhetta posta sul motovibratore e Scollegare la linea prima di eseguire eventuali manutenzioni o durante la regolazione delle masse e Ogni riparazione o sostituzione di componenti deve essere effettuata solamente da personale specializzato e Nel collegamento del motovibratore alla linea il cavo giallo verde solo verde per gli USA della terra deve essere se
15. lace them if necessary OLI SpA Via Canalazzo 35 41036 Medolla MO ITALY lt gt I OLI e mail info olivibra com www olivibra com WAMGROUP DECLARATION OF CONFORMITY With the directives of the European Union The family of motorvibrators MVE is manufactured in conformity with the following directives Directive ATEX 94 9CE 23 march 1994 Directive Machines 2006 42 CE 17 May 2006 The conformity has been verified according to the conditions included in the following standard documents EN 60034 1 EN61241 0 EN61241 1 x 113 D Ex tD A22 Tx IP 66 DECLARATION OF CONFORMITY B Type These products are manufactured according to 2006 42 EC AND SUBSEQUENT AMENDMENTS These products must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of this Directive where appropriate According to Annex II B of Directive 2006 42 CE machines the following essential requirements of safety and health protection are applied and respected 1 1 1 Definitions 1 3 7 Risks related to moving parts 1 5 5 Extreme temperatures 1 7 3 Marking of machinery 1 1 2 Principles of safety integration 1 3 8 Choice of protection against risks arising 1 5 6 Fire 1 7 4 Instruction 1 1 3 Materials and products from moving parts 1 5 7 Explosion 1 7 4 1 General principles for the drafting of 1 1 5 Design of machine
16. lat max 0 25mm max 0 01 so that the feet rest uniformly and in perfect contact with the surface to avoid internal stresses which may cause breakage of the motovibrator feet The noise level of the electric vibrators measured IS NEVER greater than 76 dB A Measured in normal operating conditions in accordance with standard UNI EN ISO 11202 Sezione 3 1 INSTALLATION To fix the motovibrator use bolts quality 8 8 nuts quality 8 8 and flat whasher A type UNI6592 Use a dynamometric wrench adjusted according to the Table tab A Remember that most of these problems and faults are caused by improper fixing and locking Anchor the motovibrator to the frame by means of a suitable 15 cm long metal chain or cable Before starting up the vibrator and after the first 24 hours of operation check Power the electric vibrator and using an ammeter pliers check all phases to make sure the power draw does not exceed the value indicated on the rating plate the fixing bolts of the motovibrator and the welds of the reinforcing plates and ribbing the anchoring chain or cable the power cable Section 4 OPERATIVE NOTES ELECTRICAL CONNECTIONS THE ELECTRICAL CONNECTIONS MUST BE CARRIED OUT ONLY BY TRAINED PERSONNEL AFTER DISCONNECTING THE POWER SUPPLY EARTHING IS COMPULSORY For the electrical connections refer to drawings The mains supply and motovibrator connections must conform to the existing safety standards defined by t
17. mpre il pi lungo per evitare che si rompa per primo in caso di cedimento e Cavi di alimentazione troppo lunghi causano cadute di tensione attenersi a quanto prescritto dalle norme Controllare che la tensione e la frequenza corrispondano a quella indicata nella targa di identificazione del motovibratore Quando i motovibratori vengono installati in coppia ognuno di essi deve essere provvisto di una propria protezione esterna di sovraccarico le quali devono essere interbloccate tra loro onde evitare il funzionamento di un solo motovibratore in caso di arresto accidentale dell altro Utilizzare sempre magnetotermici ad intervento ritardato in modo da evitarne l intervento durante la fase di avviamento nella quale la corrente assorbita pu raggiungere livelli elevati soprattutto in presenza di basse temperature Protezione al sovraccarico NON SUPERIORE al 10 dei dati di targa pena il decadimento della garanzia L OPERAZIONE DEVE ESSERE ESEGUITA ESCLUSIVAMENTE DA PERSONALE QUALIFICATO Tutta la componentistica elettrica che l installatore andr ad inserire nel motovibratore elettrico es protezioni per il sovraccarico sensori dovr essere conforme e Per la Certificazione ATEX 113D alla Direttiva ATEX 94 9 CE Il 3D o superiore e Per la Certificazione Class Il Div 2 all articolo 502 del NEC e Per il collegamento del moto vibratore in equipotenzialit collegare la macchina a terra utilizzando l apposito morsetto presente sulla ca
18. ndicato nella scheda di sicurezza prodotto trattato dall apparecchiatura nel quale il moto vibratore inserito Sezione 8 GUASTI E ANOMALIE Fare riferimento alla tabella a qm ti ps AA qm Lui LLI gt LLI DI O w TECHNICAL DATA DATI TECNICI MOUNTING SCREW AND TORQUE REQUIREMENTS COPPIA DI SERRAGGIO VITI DI FISSAGGIO i Cable type Cavo CLAMP TORQUE COPPIA SCREW VITE WASHER RONDELLA DI Class Il Div 2 type For U S Market SERRAGGIO Temp Class Class Type AWG SOW POLES POLI 5 16 8 4x 16 5 16 23 16 5 4G1 5 18 4c 1 4 64x12 1 4 9 6 5 80 C 90 C 5 16 8 4x16 5 16 23 16 5 5 16 8 4x16 5 16 23 16 5 1 2 13x24 1 2 80 58 3 8 10 5x20 3 8 45 33 462 5 16 4c Pressacavo Class Metric English Metric English N m ft T CO rem ciosstemp temp I RE M8 M16 80 C M20 VIBRATORS PARTS SCREW AND TORQUE REQUIREMENTS COPPIA DI SERRAGGIO VITI COMPONENTI DEL VIBRATORE REW FLANGE FRAME COVER FRAME COVER FLANGE FLANGE FRAME COVER FRAME FLANGE FRAME FLANGIA CORPO COP CORPO COP FLANGIA FLANGIA CORPO COP CORPO FLANGIA CORPO Nm Fe kb Nm Ft lb Nm Ft b Nm Fetb Nm Feb Nm Feto 29 8 5 7 Cable glande O Sielos Size 60 90 Size 100 110 SC VITE 12 2 3 8 10 5x 20 3 8 45 33 1 2 13x24 1 2 80 58 1 2 1
19. non conformit e o danni esterni riscontrati dovranno essere segnalati immediatamente in modo dettagliato sia allo spedizioniere che alla casa produttrice e o rivenditore Sezione 1 1 IDENTIFICAZIONE Il modello del moto vibratore e altri dati sono stampigliati sull apposita targhetta di identificazione Questi dati devono essere sempre citati per eventuali richieste di parti di ricambio e per interventi di assistenza Sezione 1 2 DESTINAZIONE D USO ATTENZIONE fatto divieto di mettere in servizio i moto vibratori oggetto del presente manuale prima che la macchina in cui saranno incorporati sia stata dichiarata conforme alle disposizioni della direttiva 2006 42 CE Il motovibratore elettrico descritto in questo manuale stato progettato e testato per un utilizzo in zone potenzialmente esplosive classificate come zona 22 secondo la norma EN 61241 10 ed in accordo alla Direttiva ATEX 94 9 CE Class Il Div 2 secondo l articolo NEC 500 5 del National Electrical Code L utilizzatore dovr assicurarsi che il luogo di lavoro all interno del quale verr installato il motovibratore elettrico sia stato adeguatamente messo in sicurezza da un punto di vista di rischio esplosione Per poter operare in condizioni di sicurezza occorre verificare che le polveri trattate abbiano una temperatura di accensione superiore a 75K della temperatura superficiale indicata sulla targhetta del motovibratore EN61241 10 Per la certificazione Class Il Div 2 sono
20. rcassa La temperatura ambiente in cui la macchina opera compresa tra 20 c 40 c REGOLAZIONE DELLE MASSE Durante le operazioni di smontaggio e rimontaggio delle parti di protezione coperchi masse togliere l alimentazione del motovibratore Eseguita l operazione su entrambi i lati rimontare i coperchi con le stesse viti e rondelle facendo attenzione che le guarnizioni siano collocate correttamente nelle propie sedi un errato posizionamento potrebbe alterare il grado di protezione IP NEMA Sezione 5 MANUTENZIONE Pulizia prima di effettuare un qualsiasi intervento di manutenzione o pulizia sulla macchina assicurarsi che questa sia messa in sicurezza Gli strati di polvere depositata non deve mai superare i 5 mm di spessore pulire con l ausilio di un panno umido Non dirigere direttamente getti d acqua ad alta pressione sul moto vibratore elettrico Tutti i motovibratori sono lubrificati in origine dalla Ditta Costruttrice motovibratori che utilizzano cuscinetti a sfera prelubrificati e schermati non necessitano di lubrificazione Nei modelli con cuscinetti a rullo previstala sostituzione del grasso esausto dopo 5000 ore di funzionamento se il motovibratore posizionato orizzontalmente o dopo3000 ore di funzionamento se il motovibratore posizionato verticalmente motovibratori concuscinetti a rulli sono comunque provvisti di canali di lubrificazione accessibili dall esterno l utilizzatore pu quindi decidere di utilizzare il m
21. ry to facilitate its handling 1 3 9 Risks of uncontrolled movements 1 5 8 Noise instructions 1 3 1 Risks of loss of stability 1 4 1 General requirements 1 6 1 Maintenance on the machine 1 7 4 2 Contents of the instructions 1 3 2 Risks of break up during operation 1 5 1 Electricity supply 1 6 4 Operator s intervention 1 7 4 3 Sales literature 1 3 3 Risks due to falling or ejected objects 1 5 2 Static electricity 1 7 1 Information and warnings on the machine 1 3 4 Risks due to surfaces edges or angles 1 5 4 Errors of fitting 1 7 2 Warning of residual risks OLI SpA undertakes to transmit in response to a reasoned request by the national authorities relevant information on the products on the present declaration except for intellectual properties of the producer The information will be transmitted directly to the national authority as requested Person authorised to compile the technical documentation Giorgio Gavioli OLI S p A Via Canalazzo 35 41036 Medolla MO Italy TA Medolla 02 05 2010 General Manager MVE WITH BLADE WEIGHTS MVE CON MASSE A LAMELLE MODEL MODELLO 50Hz 60Hz SoHz 60Hz SoHz 60Hz rimase O 6o o a S o Fc100 FC 100 FC 100 FC 75 FC 100 FC 83 3 FC 83 3 FC 50 FC 66 FC 66 6 FC 100 FC 66 6 FC 25 FC 33 FC 49 9 FC 75 FC 49 9 FC 33 2 FC 50 FC 33 2 FC 16 5 FC 25 FC 1 6 5 TURNED BLADE ON EACH SID MASSE G
22. t statica 1 7 1 Informazioni e avvertenze sulla macchina OLI S p A si impegna a trasmettere in risposta a una richiesta adeguatamente motivata delle autorit nazionali informazioni pertinenti sui prodotti oggetto della presente dichiarazione fatti salvi i diritti di propriet intellettuale del fabbricante Le informazioni verranno trasmesse direttamente all autorit nazionale che le ha richieste La persona autorizzata a costituire la documentazione tecnica Giorgio Gavioli A Firma Giorgio Gavioli il Legale Rappresentante LA OLI S p A Via Canalazzo 35 41036 Medolla MO Italy Medolla 02 05 2010 CODE OLMVEITENO1 DATE 11 2010

Download Pdf Manuals

image

Related Search

Related Contents

CALDERA PELLET KCB 20  Samsung GT-B3800 Instrukcja obsługi  Skipper CE (IT)  SE330 Issue 2 Builder`s Guide  Dynex Universal AC/DC Power Adapter FAQ  FLOCULANT PASTILLES  ファイル転送ソフト 取扱説明書  TKS 1500 ECO  

Copyright © All rights reserved.
Failed to retrieve file