5.8GHz WIRELESS A/V/ALARlVl TRNSMITTER USER MANUAL
Contents
1. p Max 6002 ALARM INPUT TTL CMOS Level Detection DIMENSIONS L 85 mm H 30 mm D 16 mm FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help I This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated2. 5 8GHz WIRELESS A V ALARM TRANSMITTER USER MANUAL MODEL 1 Panel View 5 8G TX EA A a 1D ADDRESSING DC 12V IN 1 5A ABS 7 ya J Pa EN E OlT iole O IION oe WP 0 je G 7 DBB w HEHE kaho OD oo S os ni r POWER DISARM ABCD 4 oee snc tsvoure amg pres STATE CH SELECT ID ALARM MAX 750mA ALARM IN a w DC 12V IN Power input DC 12V 1 5A DC 12V OUT DC 12V 750mA for box camera only and with the over current protector Note If you don t use this port for cameras you can use the DC 12V 500mA adaptor ALARM IN Once triggered the built in buzzer rings on for a 20 sec time This port could be connected to alarm sensor e g PIR Detector Magnetic Reed Switch Detector AUDIO IN RCA female for input audio signal VIDEO IN BNC female for input video signal POWER State LED Indicated to power on and ARM status o D Ha QUe Indications Power State LED Power On On ARM High speed Flashing DISARM DISARM at 5800VT transmitter s side only CH SELECT AB C D 5 8GHz transmission channel selection oN A B Cc D u N N 9 ID AND ALARM MUTE ID address setting is use for paring with 5800VR receivers It must be make the same code setting to link transmitter and receiver each other The alarm mute function is use for muting built in buzzer at 5800VT side only Bit 4 Alarm Mute 0 ON 1 Bit 2 Bits ID Add
3. ress Pairing with RX NI Om om e wn o 1 SW ON 0 SW OFF 10 ANT RP SMA connector for connected to 5 8 GHz antenna REMARK When the frequency channels have the interference adjust antenna or change the channel of transmitter and don t close to 802 11 a b g AP router and other 5 8GHz devices Note Please keep 3 5 meter away 2 Caution for Installation 2 1 Be careful never let any water in this equipment 2 2 If necessary use a soft cloth moistened with alcohol to wipe off the dust 2 3 Be extra careful not to shake the unit 2 4 Avoid places where temperatures exceed 50 C or higher 2 5 Avoid places where there are frequent vibrations or shocks 2 6 When any abnormalities occur make sure to unplug the unit and contact your local dealer 3 Packing 3 1 Transmitter x1 3 2 Antenna x1 3 3 User manual x1 3 4 Screws x4 3 5 Plastic Conical Anchor x4 3 6 Power Adaptor x1 Option 4 Specification CHANNAL CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 FREQUENCY 5740 5752 5771 5790 5809 5828 5847 5860 MHz MHz MHz MHz MHz MHz MHz MHz RF IMPEDANCE 50 Q Typical POWER DC12V 1 5A Adaptor CURRENT CONSUMPTION 220 mA Typical Start up current 500mA DC12V Input DC OUTPUT DC12V 750mA RF OUTPUT POWER 10mW VIDEO INPUT 1 0 Vp p Composite 759 AUDIO INPUT 2 0 Vp p Typical 3 0 Vp
4. with a minimum distance of 20 centimeters between the radiator and your body Any changes or modifications including the antennas made to this device that are not expressly approved by the manufacturer may void the user s authority to operate the equipment Q2010 04 23
Download Pdf Manuals
Related Search