USER MANUAL OF WP-SC10-RTR, WP-SC8-RTR, WP-SCB
Contents
1. CANNOT be used to connect with the LED Program Card Please only use the special port between the terminals ABC to connect with the Program Card To Program Card2. frequently used in steering By the way in the process of braking or reversing if the throttle stick is moved to forward zone the motor will run forward at once Forward Reverse mode uses Single click to make the car go backward When you move the throttle stick from forward zone to backward zone the car will go backward immediately This mode is usually used for the Rock Crawler 1 2 Drag Brake Force Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a neutral brushed motor while coasting 1 3 Low Voltage Cut Off The function prevents the lithium battery pack from over discharging The ESC detects the battery s voltage at any time if the voltage is lower than the threshold for 2 seconds the output power will be cut off and the red LED flashes in such a way y v Yr tr Yr wr 1 4 Start Mode Also called Punch Select from Level to Level9 as you like Level1 has a very soft start effect while level9 has a very aggressive start effect From Level to Level9 the start force is increasing Please note that if you choose Level7 to Level9 mode you must use good quality battery with powerful discharge ability otherwise these modes cannot get the burst start effect as you want If the motor cannot run smoothly that means the motor is trembling it may caused by the weak discharge ability of the battery please choose a better one or a softer gear
3. ratio 1 5 Maximum Brake Force The ESC provides proportional brake function The brake force is related to the position of the throttle stick Maximum brake force refers to the force when the throttle stick is located at the end point of the backward zone A very large brake force can shorten the brake time but it may damage the gears The Disable option inhibits the inherent brake function of the speed controller When this option is selected the brake function is realized by a traditional mechanical disc brake system driven by a servo 2 Reset Allltems To Default Values At any time when the throttle is located in neutral zone except in the throttle calibration or parameters program process hold the SET key for over 3 seconds the red LED and green LED will flash at the same time which means each programmable item has be reset to its default value TROUBLE SHOOTING Trouble Possible Reason Solution After power on motor doesn t work The connections between Check the power connections and the cooling fan doesn t work battery pack and ESC are not Replace the connectors correct After power on motor can t work but emits beep beep beep beep alert tone Every beep beep has a time interval of 1 second After power on red LED always lights the motor doesn t work Input voltage is abnormal too high or too low Check the voltage of the battery pack 4 Plug the control
4. wire into the throttle channel of the receiver correctly Throttle signal is abnormal The wire connections between ESC and the motor are not correct The throttle signal is lost The motor runs in the opposite direction when it is accelerated Swap any two wire connections between the ESC and the motor The motor suddenly stops running while in working state Check the transmitter and the receiver Check the signal wire from the throttle channel of your receiver Red LED flashing means Low Voltage Green LED flashing means Over heat The ESC has entered the Low Voltage Protection Mode or Over heat Protection Mode 1 The battery has a bad discharge performance 2 Gear ratio is too aggressive 3 The Start Mode Punch of the ESC is too aggressive Over current protection motor demagnetization or motor is over load Mistakenly uses the Rx wire to connect to the program card box When accelerating quickly the motor stops or trembles 1 Use a better battery 2 Use lower KV motor or softer gear ratio 3 Set the Start Mode Punch to a softer value 1 Reduce the load Use softer gear ratio or reduce the input voltage 2 Change the motor Connect the program card box to the special programming port of the ESC don t use the Rx wire When the throttle stick is in the neutral range the red LED and the green LED flashes synchronously Cannot connected with the LED Program Card o
5. USER MANUAL OF WP SC10 RTR WP SC8 RTR WP SC8 ADV RTR WP S8A RTR WP S8B RTR ESC HW SM602ENG 20130717 Page 1 of 2 DECLARATION Thanks for purchasing our Electronic Speed Controller ESC The power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the correct use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses or costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury consequential damages resulting from our product or our workmanship FEATURES Completely water proof and dust proof The ESC works properly even under water Please remove the cooling fan when running car in water and after running please make the ESC clean and then dry it to avoid the oxidation of copper connectors Excellent start up acceleration and linearity features suitable for truggy especially short course trucks and buggy The built in switching mode BEC has powerful output to supply all electronic equipments There is a mounting stand for installing the ESC on chassis easily and firmly Proportional ABS brake function with 5 steps of maximum brake force adjustment 8 steps of drag brake force adjustment Also compatible with the mechanical disc brake system Multiple protection features Low voltage
6. cut off protection Over heat protection Throttle signal loss protection Motor blocked protection Easily programmed with the SET button of the ESC and also compatible with pocket sized Program Card External Programming Port EPP easy to connect with program card and also works as power port for cooling fan e SPECIFICATIONS WP SC1O RTR WP SC8 RTR SWP SC8 ADV RTR WRES3ARTR WP S8B RTR Cont Burst Current 80A 520A 80A 520A 120A 760A 100A 650A 150A 950A Motor Supported Sensorless brushless motors 1 8 1 8 4 10 ScT Truggy 1 10 SCT Truggy Buggy Monster SCT Buggy Truggy Thugasimonatar Cars Applicable Bugay Monster 1 8 SCT Buggy Incl Traxxas 1 10 HG Traxxas 1 10 Truggy Buggy __Truggy Bu 2S Lipo KVs6000 4S Lipo KVs3000 2S Lipo KVs6000 Motor Limit lan 3S Lipo KVs4000 ES 3S Lipo KV lt 4000 4S Lipo KV lt 2600 6S Lipo KVs2400 Resistance 0 0007 ohm 0 0004 ohm 0 0005 ohm 0 00035 ohm Batte 6 9 cells NIMH 6 12 cells NIMH 6 18 cells NiMH ry 2 3S Lipo 2 4S Lipo 2 6S Lipo BEC Output _note1 _6V 3A Linear mode 6V 3A Switch mode Dimension 59 3 L x 38 4 W x 33 6 H 59 5 L x48 W x42 H Weight With Wires 110g 113g 173g 178g NOTE1 The cooling fans of ESC is supplied by the built in BEC so it is always working under 6V Battery Black Battery Red BEGIN TO USE THE NEW ESC WARNING For safety please alway
7. e calibrate the throttle range again from step A to step D f ob or i p Top point of full throttle Top point of full brake C Set the 3 points according to the steps shown in the pictures on the right side 1 The neutral point Move the throttle stick at the neutral point and then click the SET key the green LED flashes 1 time 2 The end point of forward direction Move the throttle stick at the end point of forward direction and then click the SET key the green LED flashes 2 times 3 The end point of backward direction Move the throttle stick at the end point of backward direction and then click the SET key the green LED Neutral point 4st Click 2nd Click 3rd Click flashes 3 times Throttle range is calibrated motor can be started after 3 seconds D Green LED flashes once l Green LED flashes twice I Green LED flashes thrice 3 Check LED Status In Normal Running Roe F gt Normally if the throttle stick is located in the neutral range neither the red LED nor the green LED lights gt The red LED lights when the car is running forward or backward and it will flash quickly when the car is braking gt The green LED lights when the throttle stick is moved to the top point of the forward zone PROGRAMMABLE ITEMS LIST The italics texts in the following form are the default settings Programmable Items Forward Forward Reverse 1 Runnin
8. es Hold SET key for 3 seconds Red LED flashes 1 time choose None Red LED flashes 2 times choose 2 6V Press Red LED flashes 3 times choose 2 8 V SET key Red LED flashes 4 times choose 3 0V Red LED flashes 5 times choose 3 2V Red LED flashes 6 times choose 3 4V Enter the 3rd item Low Voltage Cut Off uo J YOWMS uay PUB DSA y yo Yoyms BuiwwesBod ysiuty Hold SET key for 3 seconds Enter the N item Note gt Inthe program process the motor will emit Beep tone when the LED is flashing gt We use a long time flash and long Beep tone to represent number 5 for easily identify the items of the big number Press SET key to choose the value the flash times of RED LED means the serial number of the value 1 time means the ist gt value 2 times means the 2nd value Green LED flashes for N times Release SET key A long time flash Motor sounds B the No 5 item A long time flash a short time flash Motor sounds B B the No 6 item A long time flash 2 short times flash Motor sounds B BB the No 7 item A long time flash 3 short times flash Motor sounds B BBB the No 8 item the No 9 item A long time flash 4 short times flash Motor sounds B BBBB equipment Note3 The Rx wire of the ESC for connecting receiver
9. g Mode with Brake with Brake 2 Drag Brake Force 0 3 Low Voltage a Cut Off Threshold Non Protection 4 Start Mode Punch Levelt 5 Max Brake Force Programmable Value EEE TR S O Ee Forward and O 5 1o 20 40 eo so 100 2 6V Cell 30V 32v 34v 2 8V Cell Cell ICell_ Cell E Level3 ESEJ Levels Level Levels Level9 50 1 Programmable Values 1 1 Running Mode In Forward with Brake mode the car can go forward and brake but cannot go backward this mode is suitable for competition Forward Reverse with Brake mode provides backward function which is suitable for daily training Note Forward Reverse with Brake mode uses Double click method to make the car go backward When you USER MANUAL OF WP SC10 RTR WP SC8 RTR WP SC8 ADV RTR WP S8A RTR WP S8B RTR ESC HW SM602ENG 20130717 Page 2 of 2 move the throttle stick from forward zone to backward zone for the first time The 1 click the ESC begins to brake the motor the motor speeds down but it is still running not completely stopped so the backward action is NOT happened immediately When the throttle stick is moved to the backward zone again The 2 click if the motor speed is slowed down to zero i e stopped the backward action will happen The Double Click method can prevent mistakenly reversing action when the brake function is
10. r LCD Program Box 2 Program the ESC with the LED program box Optional PROGRAM THE ESC 1 Program the ESC with the SET button on the ESC Turn off the ESC Turn on the transmitter Hold the SET key Switch on the ESC Red LED flashes Green LED flashes for 1 time Enter the corresponding programmable item the RED LED flashes for several times the times presents the current value of this item Press the SET key to choose the programmable value the RED LED flashes for several times the times presents the serial number of the value you are choosing Red LED flashes for 1 time to choose Forward with brake ane Red LED flashes for 2 times to choose Forward Reverse with brake Red LED flashes for 3 times to choose Forward and Reverse Enter the 1st item Running Mode Release SET key Hold SET key for 3 seconds Press SET key Red LED flashes 1 time choose 0 Red LED flashes 2 times choose 5 Red LED flashes 3 times choose 10 Red LED flashes 4 times choose 20 Press Red LED flashes 5 times choose 40 SET key Red LED flashes 6 times choose 60 Red LED flashes 7 times choose 80 Red LED flashes 8 times choose 100 Green LED flashes for 2 times Enter the 2nd item Release Drag Brake Force SET key Hold SET key for 3 seconds Release Green LED flashes SET key for 3 tim
11. s keep the wheels away from the track when switching on the ESC 1 Connect The ESC Motor Receiver Battery And Servo The A B C wires of the ESC can be connected with the motor wires freely without any sequence If the motor runs in the opposite direction please swap any two wire connections Receiver 2 Throttle Range Setting Throttle Range Calibration eee In order to make the ESC match the throttle range you must calibrate it when you begin to use a new ESC or a new transmitter or change the settings of neutral position of the throttle stick ATV or EPA parameters etc Blue wire A Yellow wire B Orange wire C Brushless motor The following pictures show how to set the throttle range with a Futaba transmitter A Switch off the ESC turn on the transmitter set the direction of throttle channel to REV set the EPA ATV value of throttle channel to 100 and disable_the ABS function of your transmitter Hold the SET key and then switch on A the ESC and release the SET key as A soon as possible when the red LED begins to flash Note2 Push B SET Hold the SET button m EHH HE Release the SET button as soon as the red LED starts to blink Turn on the swith Note2 If you don t release the SET key as soon as the red LED begins to flash the ESC will enter the program mode in such a case please switch off the ESC and r
Download Pdf Manuals
Related Search