208L Installers Manual
Contents
1. M aa SECTOR 5 FAST LOOP ENTRY GUARD DOOR ANNUNICATOR SELECT SECTOR 6 FAST LOOP ENTRY GUARD DOOR ANNUNICATOR SELECT Alli LL A nr SECTOR 7 FAST LOOP ENTRY GUARD DOOR ANNUNICATOR SELECT LEITET imm SECTOR B FAST LODP ENTRY GUARD DOOR ANNUNICATOR SELECT STREN OUTPUT LIMITATIONS m EI i iiL eee a E i i i rr iis A AUTO ISOLATE ENABLE e a i FJ J V E al INVERT VOLTAGE OUT r T MET 3 LL BULL rm rr E L E D EXTINGUISH ENABLE DISABLED 0 ETE e ee POWER UP DELAY DISABLE DISABLED 1 e TET TT i itae i i A RR TT T n ta NO ARMING WITH A SECTOR ISOLATED DISABLED 0 DISABLED KEYPAD TAMPER ENABLED 1 LAST CONDITION 0 POWER UP DISARMED ENADLE quick ARM ENABLE 3 KEY To TT SS T E BISARED 0 ENTRY TIME FOR ENTRY GUARD o Rostos RESERVED FOR FUTURE USE DO NOT USE Do TT LL LOC DESCRIPTION DATAL DATAS 032 035 USER 1 ARM DISARM CODE MASTER CODE Me USER 2 ARM DISARM CODE EA Ea USER 3 ARM DISARM CODE o ommo 15 A NEN TIMED LATCHED OUTPUT MP eee rere USER 5 ARM DISARM CODE DISABLED 15 e mms USER B ARM DISARM CODE DISABLED 15 DISABLED 15 DISABLED 15 USER 7 ARM DISARM CODE DISABLED 15 DISABL D 15 T_T p EE A CCT USER 12 ARM DISARM CODE USER 13 ARM DISARM CODE USER 14 ARM DISARM CODE USER 15 ARM DISARM CODE GO TO PROGR2. LOCATION 021 ENABLING THE AUTOMATIC ISOLATE FEATURE Location 021 is used to enable the Auto Isolate feature of the 208L This feature is enabled by placing a zero 0 in this location Factory default is one 1 and this feature is not enabled If this feature is selected and and a sector is not secured at the end of the exit delay it will be auto isolated and the security system will arm normally If sector is not secure at code entry but is secure at the end of the exit delay that sector will not be auto isolated and will arm in a normal condition LOCATION 022 INVERTING THE ALARM VOLTAGE OUTPUT If location 022 contains a 1 the alarm voltage on terminal 20 will be normally high and open circuit in an alarm condition This allows this output to be used as the holdoff for a satellite siren If location 022 contains a O the alarm voltage output will be normally open and switch to 12 volts in alarm This output will turn off at the end of siren time regardless of the condition of location 022 I LOCATION 023 ENABLING OF THE L E D EXTINGUISH FEATURE Keypad LEDs with the exception of the A C LED will be extinguished after 60 seconds of keypad inactivity if a one 1 is placed in location 023 The LEDs will become illuminated immediately if any key on the keypad is pressed LOCATION 024 POWER UP DELAY DISABLE If a one 1 is placed in location 024 the 208L will not delay 60 seconds before accepting open or short inp
3. EMETAENGEOSURESdinensi ones SS AA SS eS O EN E SS HIPPING WELGH EEE Die re eens eal er 3 he a a ur a Ly WARRANTY STATEMENT DIRECT ALARM SUPPLIES LTD GUARANTEES THIS PRODUCT AGAINST DEFECTIVE PARTS AND WORKMANSHIP FOR TWENTY FOUR 24 MONTHS FROM DATE OF PURCHASE IF ANY DEFECT APPEARS DURING THE WARRANTY PERIOD RETURN IT TO DAS POSTAGE PREPAID THE UNIT WILL BE REPAIRED AND RETURNED DAS ASSUMES NO LIABILITY FOR CONSEQUENTIAL OR INDIRECT DAMAGE AND ACCEPTS NO RESPONSIBILITY FOR REPAIRING DAMAGE TO THE PRODUCT CAUSED BY MISUSE CARELESS HANDLING OR WHERE REPAIRS HAVE BEEN MADE BY OTHERS NO OTHER GUARANTEE WRITTEN OR VERBAL IS AUTHORIZED BY OR ON BEHALF OF DIRECT ALARMS SUPPLIES LTD RIVERWOOD NSM DIRECT ALARM SUPPLIES LTD 10 WIGGS RD A RIVERHOOD NSW AUSTRALIA e PHONE 02 5346622 FAX 02 5344277 BULLETIM IH 208L
4. this sequence by pressing 1 7 to exit programming So the entire procedure would consist of pressing 17 keys as follows 1010104 12153203 COELU 5116117308 E9101 NOTE IF THE MASTER CODE I CHANGED ALL AUXILIARY CODES ARE INVALIDATED 1 Entering and Changing an Auxiliary Code In order to program auxiliary codes you must know the master code user code 1 Each auxiliary code has its own unique number from 2 15 and must be referred to by its number The auxiliary code is programmed much Tike changing the master code For example to program auxiliary code 2 the sequence would be as follows E2 I EZIDII MIC CIEJEIEI ELE AN NEW CODE Codes 3 through 15 would be entered by using the above sequence and replacing 2 with the appropriate number 3 15 DD tomem o o o eo S ETT OT mm RN TT A A to go ot ata at A O O mm mm o a a mgpa e A DS page 14 Removing Auxiliary Codes To remove an auxiliary code simply program it to be the master code For example to remove user code 2 the sequence would be as follows 1E2 04 D233 2 E31 41 NENA E2112 0331I4 OHA User code 2 has now been eliminated Note If an attempt is made to change any of the codes from the keypad and a invalid master code is entered or a or 4 is made part of a code the keypad sounder will beep 3 times and the keypad will return to the normal state If the master cod
5. was Tost A watchdog circuit reset will also cause the 208L to reset to the selected condition LOCATION 029 QUICK ARM ENABLE If a one 1 is placed in location 029 the 208L can be armed by pressing the 3 key on the keypad Factory default is zero 0 and the Quick Arm feature is not enabled LOCATION 030 DELAY TIME FOR ENTRY GUARD SECTORS Location 030 contains the number of 10 second increments for Entry Guard sectors The Entry Guard delay can be programmed in 10 second increments from 10 to 150 seconds 1 10 seconds thru 154150 seconds Factory default is 2 or 20 seconds LOCATION 031 FOR FUTURE USE DO NOT PROGRAM THIS LOCATION LOCATIONS 032 035 PROGRAMMING THE MASTER ARM DISARM CODE Locations 032 035 contain master arm disarm code user number 1 Location 032 contains the first digit of the code location 035 contains the fourth digit of the code THE CODE MUST CONTAIN FOUR 4 DIGITS The master code can then be used in the run mode to enter arm disarm codes 1 15 see page 13 ENTERING AND CHANGING THE MASTER CODE The factory default code will be 1 2 3 4 ME NINAR qu Pp s um pm pum pm mia v mimm rn mtn mm remm AO n e m HII i ode mo ta oma tt a mm a papa aapa apam o waama i m a NEE ta pp RA teet tI II IA ees qu m miis me u page 12 LOCATIONS 036 039 PROGRAMMING THE ARM DISARM CODE FOR USER 2 Locations 036 039 contain the arm disarm codes for user number 2 Location 036 con
6. AM CODE DISABLED 15 queam mma tm tm pe page 8 LOCATIONS 000 007 PROGRAMMING THE SECTOR TYPES Locations 000 through 007 contain a number identifying the characteristics ot each of the 8 sectors Location 000 corresponds to sect r 1 and location 007 corresponds to sector 8 Each sector will Factory default according to the following list SECTOR NUMBER DEFAULT CHARACTERISTIC SECTOR 1 ENTRY EXIT SECTOR 2 HANDOVER SECTOR 3 HANDOVER SECTOR 4 INSTANT SECTOR 5 INSTANT SECTOR 6 INSTANT SECTOR 7 INSTANT SECTOR 8 INSTANT To program sector characteristics other than the default values pro gram a number from 1 to 8 based on the characteristics found in the following list SECTOR CHARACTERISTICS DESCRIPTION ey pees bee a NUMBER Ti MA bee dip mi ai po DAY SECTOR A trip on a Day sector will produce an instant alarm when armed and activate the keypad sounder when disarmed ki 24 HOUR A trip on a 24 Hour sector will produce an instant lt i alarm when the 208L is armed or disarmed oe ENTRY EXIT A trip when armed will start entry delay When arming the sector will delay the selected number of seconds to allow exit before siren and communicator activation INTERIOR DELAY A trip on Interior Delay sector when armed in c the instant or away mode will initiate an entry delay It will be apresar ignored during exit delay and when disarmed HANDOVER Inte
7. EYPAD FS4575 16 18 VAC 1 5 AMP PLUG PACK FS4402 12V0C GAH BATTERY FS4332 Page 3 Hermes PROGRAM RESET NORMAL page 4 Terminal drawing and special notes a AO gi mm s fr r S LO A n dui ud RE DN SINE JINE S ST COLO WATER PFE GROUND LIGHTNING PROTECTION a INE a ES QEU T N Bg TO es Qs AHi E NICA TOW ha QE TA e SIE 4 277 b o SES ww 12 POTS Ew ALARM KETPAD MANUAIS KENPAOS PER SYSTUM WAXMLAM WRE NUM PER XETPAD i CRECT ALARM SUPPLIES PTY LTD XS os 8 ANN E INL 4 7877 po 3 o SL ES DETIENE e GS RUD ds STE TE nel ANY ie n 8 NM dO D mm eee ee d Oo ooo o E E E EEE 000000 Mo ww LU NN Na SECTOR 1 SECTOR aL E RA PE ta a tt A lt a a O O A A V page 5 C Terminal Description Connect one side of Sector 1 Toop The other side of loop to common terminal 2 Connect one side of Sector 2 loop The other side of loop to common terminal 2 See Terminal Drawing and repeat the above sequence for sec tors 3 8 Connect keypad wires as follows yellow to terminal 13 green to terminal 14 black to terminal 15 red to terminal 16 70 meter maximum run with 7 020 cable 150 meter maxi mum run with 14 020 cable Latched alarm output normally closed output ry contact if shunt is in left position 12 volts if shunt is in volt position Latched alarm output common output Dry contac
8. RDPI mana a qu ut pm gp PA A A O OM A OR a A A pa A Rc PR sane aavenanussnasinemenenen vasa Installation TABLE OF CONTENTS DESCRIPTION OF MAJOR FEATURES GENERAL DESCRIPTION TOREM P P STANDARD AND OPTIONAL PARTS LIST P Nd TERMINAL DRAWING AND SPECIAL NOTES TERMINAL DESCRIPTION PRIMARY PROGRAMMING INSTRUCTIONS PROGRAMMING WORK SHEET ADDITIONAL PROGRAMMING INSTRUCTIONS GENERAL OPERATING INSTRUCTIONS KEYPAD OPERATION woo wN SS q A U MM x boa CL 2OSL i Description of Major Features i Up to 15 user codes Microprocessor Watchdog circuit with dead battery microprocessor shutdown An advanced Freeze Frame alarm history allows you to see the exact condition of the control sectors during the last alarm Each sector is E 0 L supervised for maximum protection and flexibility One keypress Quick Arm feature Four wire keypad A unique keypad LED Extinguish feature saves current on standby battery and allows the keypad to be used in sleeping areas without disturbing the occupants Built in siren driver and 1 Amp DC voltage output 400 m of regulated auxiliary power 100 mA of switched auxiliary power Separate fuse for auxiliary power makes the keypad tamper resistant 4 Entry Guard capability selectable by sector Day Annunciation selectable by sector d Programmable Automatic Isolate capability A C Failure detection Advanced transien
9. e 13 C Genera Operating Instructions Arming ahd Disarming the 208L To turn the security system on close all protected doors and windows The green SECURE LED will be on Input a valid code to change the armed status The following conditions will prevent the armed status from changing when a code is entered 1 The SECURE LED is out and the system is currently disarmed the keypad sounder will beep 3 times if green SECURE LED is not illuminated 2 The siren is currently on for something other than a control sector in this case silence the siren by entering a 4 digit code 3 The keypad sounder is currently beeping for a Day sector in this case silence the keypad sounder by entering a 4 digit code Isolating Sectors To isolate any of the sectors 1 8 disarm the control and press sector numbers to isolate and If the control is in the disarmed state the isolate condition of the sectors will toggle C Entering and Changing the Master Code User Code 1 When the 208L is first powered up the master code is standard default code 1 2 3 4 To change the master code from the keypad in the run standard mode the following procedure must be followed To change the master code from 1 2 3 4 to 5 6 7 8 the sequence is as follows Press 1 4 This enters programming for user code 1 then 1 2 3 4 old master code press 1 1 verifying that used code 1 is being changed then new code 5 6 7 8 Now end
10. e function codes that are used to program the 208L These are 210 220 and 230 and are described below After all the data has been entered into locations 000 095 you must enter the code 220 followed by j to permanently place the information into the EEPROM If this step is not taken the data in the EEPROM will not change and the 208L will not change characteristics To change the 208L data back to the original default values enter the code 210 followed by a f to load the data into the RAM memory and then 220 followed by a to load that data into the EEPROM To exit the Program mode after it has been accessed with the four digit program code enter code 230 followed by a f A MM M moment amo LE EH PROGRAMMING WORKSHEET page 7 Lon DESCRIPTION o DATA 000 SECTOR 1 TYPE 001 SECTOR 2 TYPE 7 Hannover 5 002 SECTOR 3 TYPE wor RE 40 dne md I 008 EXC 010 SIREN CUTOFF TIME 2MIN INC EXITO eT a KEYPAD PANIC AUDIBLE DISABLE i A SECTOR 1 FAST LODP ENTRY GUARD DOOR ANNUNCIATOR SELECT ar Td O SECTOR 2 FAST LOOP ENTRY GUARD DOOR ANNUNICATOR SELECT e ei NOME SELECTED 0 NONE SELECTED 0 SECTOR 3 FAST LODP LNIRY GUARD DOOR ANNUNTCATOR SELECT SECTOR 4 FAST LOOP ENTRY GUARD DOOR ANNUNICATOR SELECT a o
11. e is changed all auxiliary codes will be invalidated Activating Entry Guard This feature must be individually enabled for each sector by programming the correct number in locations 012 thru 019 Entry Guard is activated by pressing the number two 2 key and waiting 5 seconds If no other keys are pressed within 5 seconds the system will become armed in the Entry Guard mode While in this mode all designated Entry Guard sectors will cause the keypad sounder to sound for the period selected in location 030 All other sectors will be isolated If a Entry Guard sector is violated and a valid code is not entered before the delay period 1s over the siren will be activated While in the Entry Guard mode the 208L can also be disarmed with the number two 2 key unless the siren has been activated After siren activation a valid 4 digit user code must be entered to disarm the system and silence the siren A Activating Day Annunciator This feature must be individually enabled for each sector by programming the correct number in locations 012 thru 019 To activate Day annunciation disarm the control and press the number one 1 key on the keypad If no other keys are pressed within 5 seconds the keypad sounder will beep and the Day Annuncia tor will become activated Use the same procedure to remove this feature Alarm History Pressing the zero 0 key for 5 seconds will cause the keypad to annunciate Freeze Frame alarm history after f
12. e keypad sounder is built into the keypad and will sound for the following reasons M e Beeps for all keypresses Sounds continuously during entry delay Pulses when a Day sector trips or when the 208L is armed with a sector isolated When pulsing it can be silenced by entering a code armed status will not change e 3 Beeps for trying to arm when a faulted sector is not isolated and Auto Isolate is disabled Beeps 1 second for Day Annunciation and activation of Day Annuncia tion 3 Beeps when errors are made reprogramming codes Beeps 1 second at the end of the exit delay Beeps 3 times when al sectors are isolated Beeps 3 times when a error is made when isolating a sector Beeps 3 times to let the user know if the armed status did not change MP up a a mto Lt tt tao o PI tm o a La La o tt DDD DS PPP DDD a a P LP page 16 SPECIFICATIONS ERE des E TT LR pi SOBERATING POWERS copo ABS VAC Baal SAU LE VARI POWERS SS NM MEN LIT Si LL LLL T gt tr eran Siaa han dia m A ia SSTRENCDRIVER lt a ae gt E ia eerie up er rr RT O pini riri SR LE WA er Perg bra a r TL RN Arma A ARM CURREN T AVALEADEE Ys SM SUR abou driver Fivercis notcused puce m EE E TEN e ectabl ie 60H O O o uo UAT Pea EEE E AA ITEM EE EEE CEE EEE E O Se A E PERED er E LAT UU
13. es Note A zero 0 entry is treated as the factory default of 8 minutes Placing a 6 in location 010 will produce an automatic cutoff time of 12 minutes Nal LOCATION 011 KEYPAD PANIC HOLD UP DISABLE Location 011 is used to disable the audible output for the KEYPAD panic hold up alarm Placing a one 1 in location 011 will disable the keypad panic hold up alarm If this location contains 0 the 208L will have an audible keypad panic hold up output LOCATIONS 012 019 PROGRAMMING SECTOR CHARACTERISTICS Locations 012 sector 1 to 019 sector 8 are used to program the loop response time and to enable Entry Guard and or Day Annunicator features for each sector Use the following chart to determine the correct number to be placed in location 012 thru 019 to enable these features FAST LOOP RESPONSE TIME 200m5 DAY ANNUNCIATOR FEATURE DOO PH OY aim page 10 LOCATION 020 LIMITING ALARMS TO ONCE PER SECTOR Location 020 is used to limit alarms to once per sector during an arming cycle LJ When a 1 is placed in location 020 each sector will only activate the siren output once during each arming cycle If a 0 is placed in location 020 all sectors can trip an unlimited number of times per arming cycle
14. ive seconds The keypad will annunciate the sectors which produced the last alarm It annunciates by flashing the sectors that caused the alarm and lighting steady the sectors that were isolated when the alarm occurred Alarm History is erased when the 208L is placed into the program mode Sector Recycling All sectors on the 208L will reset independent of each other When a sector has reset it is them able to create another audible alarm If the siren audible has not recycled a trip or a re trip will extend the time for another recycle period Ls PPP AA PP PDD I sre eee PR PRP pt RR me page 15 Keypad Operation The 208L will accept up to four Control Keypads The keypad is a four wire keypad that has a 12 key telephone type keypad a sounder and 12 LEDs The LEDs are used to indicate the following ARMED red On when system is armed off otherwise Blinks on non 24 hour sectors as alarm memory until a valid code is entered SECURE green On when sectors 1 through 8 are secure off otherwise PARTIAL red On when the Entry Guard mode has been selected AC ON red On when AC power is on off otherwise This light will not go out in the LED extinguish mode unless A C power is lost SECTORS 1 8 On when isolated blinking when faulted off otherwise Blinks when Freeze Frame alarm history is being shown if faulted during the Tast alarm On steady if sector isolated during last alarm Keypad Sounder Th
15. rior sector that follows the delay sectors It is instant during non delay times i eu INSTANT Produces an instant alarm when tripped in the armed ies mode It is ignored when disarmed Mr page 9 LOCATION O08 PROGRAMMING THE ENTRY DELAY TIME es Location 008 contains the number of 10 second increments in the entry delay The entry delay can be programmed in 10 second increments from 10 to 150 seconds 1 10 seconds through 15 150 seconds For example placing 2 in location 008 will produce an entry delay of 20 seconds Placing a 6 in location 008 will produce an entry delay of 60 seconds LOCATION 009 PROGRAMMING THE EXIT DELAY TIME Location 009 contains the number of 10 second increments in the exit delay The exit delay can be programmed in 10 second increments from 10 to 150 seconds 1 10 seconds through 15 4150 seconds For example placing a 2 in location 009 will produce an exit delay of 20 seconds Note A zero 0 entry is treated as the factory default of 60 seconds Placing a 6 in location 009 wil produce an exit delay of 60 seconds LOCATION 010 PROGRAMMING THE SIREN SHUTDOWN RECYCLE TIMEOUT Location 010 contains the number of 2 minute increments in the automatic cutoff time The automatic cutoff time can be programmed in 2 minute increments from Z to 30 minutes 1 2 minutes through 15 30 minutes For example placing a amp in location OIO will produce an automatic cutoff time of 4 minut
16. t If shunt is Es in left position 12 volts if shunt is in volt position ul Latched alarm output normally open output Dry contact If shunt is in left position 12 volts if shunt is in volt position 20 Timed Alarm voltage output 12 volts at I amp in alarm 21 amp 22 4 Siren driver output to speaker s maximum load 4 ohms Keypad resettable power 12VDC 100 mA maximum 25 amp 26 Auxiliary power regulated 12VDC 400 mA maximum 27 Earth Ground connect to a cold water pipe or 2 to 3 meter driven rod AC input connect a 16 18 Volt 1 5 amp plug pak Battery Standby battery leads black and red connect to a 12V0C leads lead acid rechargeable battery Do not connect to a dry cell battery MS dell ola ap tp lt O ahora y ARA RA ao a a at ee ae MELLE page 6 PROGRAMMING The 208L can be placed into the Program mode by any one of the three following C methods Slide the Program Run switch from the run position down to the program position up 2 Enter the 4 digit Go To Program code which must have been entered into locations 92 95 previously At initial power up there is no code in these slots and the 208L must be programmed by method 1 above or method 3 below The control must be disarmed 3 Plug the optional model 8950 programmer into the 4 pin male outlet marked program on the 208L P C Board When the sys
17. t protection featuring state of the art Transorb technol ogy Optional Manual Panic activation from the keypad EEPROM memory holds all programming features even after total power failure 1 C Page 2 nel The DAS 208L is a versatile 8 sector control panel Its microcomputer design ee 208L INSTALLATION MANUAL General Description gives some of the most versatile yet easy to use features in the industry today Each of the Eight sectors can be programmed to be one of six different types including 24 Hour Handover and Day Sector Each sector is individually annunciated and can be isolated from the keypad Read the OPERATORS MANUAL before you begin the installation for the best overall description of how the 208L functions After installation of the security system complete the information on page 2 of the operators manual and explain the system operation to all security system owners operators Standard Parts List The 208L is shipped with the parts listed below included PART NO pe M R FS4560 IM 208L 0M 208L QUANTITY PART DESCRIPTION MASTER CONTROL PANEL INCLUDING KEYPAD INSTALLATION MANUAL OPERATORS MANJAL Optional Parts List The following parts are available for use with the 208L PART DESCRIPTION PART NO is mE eo A ro ENE ae PROGRAMMER WITH DIGITAL NUMERIC DISPLAY FS4597 KEYSWITCH MODULE allows arming with a momentary keyswitch F54578 REMOTE K
18. tains the first digit of the code location 039 contains the fourth digit of the code THE CODE MUST CONTAIN FOUR 4 DIGITS To disable a code enter a 15 as the first digit of the code This code can be changed in the RUN mode using the master code see page 13 ENTERING AND CHANGING AUXILIARY CODES The factory default for user 2 is disabled IONS 040 091 PROGRAMMING THE ARM DISARM CODE FOR USERS 3 15 Locations 040 091 contain the arm disarm codes for user number 3 15 To program these codes follow the instructions for user number 2 corresponding to the following table CS CO Ss 048 05 Can be changed in the run mode 056 059 Can be changed in the run mode x tU DEN 060 063 Can be changed in the run mode US 9 064 067 Can be changed in the run mode 068 071 Can be changed in the run mode 072 075 Can be changed in the run mode 076 079 Can be changed in the run mode 080 083 Can be changed in the run mode 084 087 Can be changed in the run mode 088 09 Can be changed in the run mode LOCATIONS 092 095 PROGRAMMING THE GO TO PROGRAM CODE Locations 092 095 contain the GO TO PROGRAM code Location 092 contains the first digit of the code location 095 contains the fourth digit of the code THE CODE MUST CONTAIN FOUR 4 DIGITS The GO TO PROGRAM code can be used in the run mode to enter the program mode To disable the GO TO PROGRAM code enter a 15 in location 092 The factory default is GO TO PROGRAM code disabled C A pag
19. tem keypad is utilized for programming as described by methods 1 and 2 above the 208L will be in the program mode and the yellow LED s will display the data in location 000 For easier programming use the Installers Binary Programming Guide label which is included with your keypad The data is displayed using a Binary system With this system the yellow Sector 1 LED equals 1 when illuminated The Sector 2 LED equals 2 when illuminated The Sector 3 LED equals a 4 when illuminated The Sector 4 LED equals 8 when illuminated Thus if the data in location 000 is 9 the LED for Sector 1 1 and Sector 4 8 would be illuminated By adding the two values together 14829 you would determine that the data in location 000 is 9 If the data in location 000 is 6 the LED for Sector 2 2 and Sector 3 4 would be added 2 4 6 and the data in location would be 6 If no LED s are illuminated the location has zero 0 To step from location 000 to 001 through 095 press the f key To_go to a specific location press the location number followed by the 4 key The yellow LED s will then display the data in that location Data is changed by entering a number 0 to 15 followed by a a data enter q i When using the optional 8950 Programmer the programming keystrokes will be the same as with the system keypad The 18950 however has the ability to display the location number and the data in that location on the numeric display There are thre
20. uts from any sector If a 0 is programmed sensors on all sectors are allowed 60 seconds to stabilize at power up after a total power shutdown and battery failure After 60 seconds the 208L will once again accept loop opens or shorts as an alarm condition This 60 second period will also be initiated after a watchdog circuit reset condition LOCATION 025 NO ARMING WITH A SECTOR ISOLATED If a one 1 is placed in location 025 the 208L cannot be armed with any sector isolated If programmed with a O up to 7 of the 8 burglary sectors can be isolated and the 208L can still be armed page 11 LOCATION 026 MAKING THE LATCHED OUTPUT TIMED If a l is placed in location 026 the latched alarm outputs terminals 17 18 and 19 will turn off at the end of siren time If location 026 contains a Q these outputs will remain on until an arm disarm code is entered LOCATION 027 KEYPAD TAMPER FEATURE Placing a 1 in location 027 will enable the keypad tamper feature When this feature is enabled the 208L will lock out the keypads for 1 minute if 30 random keypresses are made without producing a valid code LOCATION 028 POWER UP DISARMED ENABLE pi rompem If a one 1 is placed in location 028 the 208L will power up in the disarmed condition if there is a total power shutdown and battery failure If a 2 is placed in this location the 20 amp L will power up armed If it contains a 0 the 208L will power up in the state it was in when power
Download Pdf Manuals
Related Search