Clamp Frame Installation Manual PR
Contents
1. n Note O Tighten the nuts until the screw tips are flush with the tops of the nuts or protrude from them as shown below If the screw tips are recessed within the nuts when embroidering is started the screws may hit the embroidery machine preventing embroidering from continuing O Screw tip Nut O When hooping a shoe in the clamp frame Loosen and remove the two thumb screws the heel of the shoe should extend out on the embroidery machine and then from the notch in the frame If the heel of remove the embroidery frame holder from the shoe is inside the notch the shoe may the carriage hit the embroidery machine preventing embroidering D Thumb screws e The removed thumb screws will be used to O Notch install embroidery frame holder D Insert the pins on the frame mounting plate of the carriage into the holes on both sides of the mounting plate of embroidery frame holder D O If the shoe is hooped with the sole and clamp frame at an angle greater than 45 we recommend using clamp frame S even if the shoe is a size 27 cm US9 UK8 EUR42 or more D Memo O If the nuts are tightened too firmly when removing the item from the frame after embroidering press the area between the two screws with your fingers an2. be correctly aligned In this case the pointer indication should be used only as a reference Attach the clamp frame and then select a stitch Mi 23 2mm 36 3mm Touch E and then edit the pattern in the pattern editing screen The same screen appears regardless of whether clamp frame S SL or SR is attached D Memo O It is recommended to use 3 embroidery colors or less Touch to display the embroidering settings screen The frame appears in the screen with the same orientation when clamp frame SL or SR is attached 31 7 mm DI 30 1 mm 5 5 Touch to check the embroidering area E 24 Note O Be sure to check the embroidering area before starting to embroider to make sure if the item is not pulled and if the position of the frame is aligned to the item When the item is pulled forcibly or the frame position is not aligned with the item the item can not be used with the clamp frame gt Memo O Touching will return you to the pattern editing screen The settings screen reverts the pattern back to its original setting before design was changed Changes specified in the embroidering setting screen will not be applied even if MEMoRY was touched to save the pattern The orientation and position for the design will revert back to the original settings While using the clamp frame SL SR when the embroidering setting screen is displayed after creating a border pat
3. Clamp Frame Installation Manual PR 1000 PR1000e ver 4 10 PR655 PR655C About the Clamp Frame This frame will be used for embroidering specially shaped items that cannot be held in a traditional frame such as shoes and gloves Verifying the package contents Check that the following parts are included The package contents differ depending on the clamp frame kit that you have purchased If any item is missing or damaged contact your authorized sales representative N Note O This Installation Manual is included with both kits O The maximum embroidery area of the clamp frame is 24 mm x 45 mm 7 8 inch x 13 4 inches W Contents of clamp frame Kit 1 Embroidery frame holder D Clamp frame S Installation Manual Install embroidery frame holder D in order to attach the clamp frame W Contents of clamp frame Kit 2 Used to embroider shoes when size is greater than 27 cm US9 UK8 EUR42 Clamp frame SR Clamp frame SL Installation Manual Embroidery frame holder D included in clamp frame Kit 1 is necessary for attaching the clamp frames 1 5 m zZ 9 O I Items that can be embroidered When using the clamp frame a wide variety of items can be embroidered except extremely hard or thick materials JE Note When embroidering thin materials be sure to use a stabilizing product O Shoes with the size less than 23 cm
4. US5 UK4 EUR37 cannot be embroidered O The maximum embroidery area may be smaller than 24 mm x 45 mm 7 8 inch x 1 3 4 inches depending on the size depth shape or the kind of item you are embroidering W Sample projects Shoes side Shoes front Shoes tongue Gloves strap Small bag U Hooping the item The procedure for using the clamp frame S is described below Loosen the two nuts on the frame and then lift up the presser clamp Screw O Presser clamp Pass the item between the presser clamp and frame O Presser clamp O Frame gt Memo O If the item does not fit between the presser clamp and frame completely remove the two nuts Raise the presser clamp to its highest position Insert the item and then lower the presser clamp into place When you remove the nuts make sure that the screw side is facing up When hooping the shoe loosen the lacing to open the shoe wide enough and then hoop to the frame 2 5 Firmly tighten the two nuts on the frame and then pull the item to check that it is within the frame and correctly aligned e When pulling the item be sure to firmly hold the frame with one hand Area between the two nuts e The screws can be firmly tightened if you press the area between the two nuts with your fingers while tightening the screws e The screws can be further tightened by using the wrench included with the embroidery machine
5. d use the wrench included with the embroidery machine to loosen the nuts Attaching the embroidery O Pins on the frame mounting plate of the frame carriage O Holes in the mounting plate of embroidery After hooping the item in the clamp frame attach frame holder D a ai machine Install and tighten the two thumb screws X k removed in step N Note O When attaching or removing the clamp frame make sure that the start stop button of the embroidery machine is lit in red If the start stop button is flashing in green the embroidery machine may start sewing If the embroidery machine accidentally starts operating injuries may result O Before attaching the clamp frame install embroidery frame holder D on the embroidery machine 3 5 _ Note __ E Note O Please firmly tighten the two thumb screws O Be careful not to pinch your fingers with with the disc shaped screwdriver included the springs with the embroidery machine The wrong frame size may be indicated on the machine s screen if the two screws are not tightened Embroidering with the Clamp Frame Use both hands to grasp the frame hooped with the item and then attach it to embroidery G frame holder D E n Note O For 10 needle embroidery machine users Make sure that the embroidery machine is version 4 10 or later If the embroidery machine is prior to version 4 10 you must install the upgrade or the machine will not recogniz
6. e the clamp frame Frame Display setting Insert the pins on embroidery frame holder N D into the holes on both sides of the clamp When using the clamp frame select the following frame to secure it Frame Display setting The differences between clamp frame SR and clamp frame SL will not show in the Frame Display screen A 37 Frame Display a lt gt 5 00 Zen O Make sure that the pins on the embroidery frame Starting embroidering holder fit into the positioning slot and hole on the embroidery frame H Removing the clamp frame AAS Note While grasping the clamp frame with both hands lift up both springs with your fingers and then pull off the clamp frame toward you When the clamp frame is attached cutwork basting and appliqu functions cannot be sewn When the clamp frame is attached to the 10 needle embroidery machine the embroidery position alignment using the built in camera is not available The maximum sewing speed can be set to one of five levels between 400 and 600 spm when the clamp frame is used The maximum sewing speed setting is specified from the embroidering screen 4 5 D Memo e Embroidery machines equipped with an LED pointer can use it to automatically adjust the position of the attached clamp frame With material that has a very uneven or textured surface such as shoes etc the position of the LED pointer may not
7. tern in step O the pattern will be ungrouped Select each pattern in order to move or rotate it If the machine is turned off in the middle of embroidering the machine will automatically save the design position when turned on again except the changes specified in the embroidering setting screen After checking the embroidering area touch to begin embroidering
Download Pdf Manuals
Related Search