User Manual AquaFresh Chlorine-Free System
Contents
1. Probe 33 a ges 3 4 Dual Pump E Sanitiser and Enhance 0000 EET arog Ww Bottom Mount Bracket UU Acid Drum Drill a 10mm hole in each of the screw on drum caps slightly larger than the diameter of the tubing to allow venting and to prevent the drum walls from being sucked in as the chemicals are used Pass a length of supplied tubing through the hole in the appropriate drum cap Place the supplied sinkers onto the tubing and attach the appropriate drum filter When placing the tubing into the drums measure the tubing against the outside of each drum so that the drum filter will be 10 15mm above the bottom of the drum and then apply several turns of PVC tape at a point above the cap to prevent the tubing from slipping further into the drum Lower the drum filter and sinker into the drum and screw on the cap Page 11 The AquaFresh Front Panel AquaFresh Display The AquaFresh uses a four line LCD display to provide the user with information Line 1 Line 2 Line 3 Line 4 LCD Display Line 1 15 27 NORMAL Auto Line 2 AutoON gt AutoOFF 23 00 Line 3 Sanitiser Feed today Line 4 pH 7 5 SET 7 6 READ MANUAL FOR DETAILED INSTRUCTIONS shows the current time and the mode of operation In the example above line 1 tells you that the time is 3 27pm and the AquaFresh is operating in Normal Automatic mode Note that the AquaFresh displays the2. Stabiliser is not required in an AquaFresh pool pH Adjust the pH to suit your pool type This is usually in the range of 7 2 to 7 6 note that pH and TA are related and will likely need to be adjusted together Total Alkalinity TA Total alkalinity is also known as carbonate hardness or TA for short The recommended level is between 80 and 120ppm TA is related to pH in that it stops the pH from varying quickly with small additions of acidic or alkaline chemicals When the TA is low it is almost impossible to control the pH To raise the TA buffer sodium bicarbonate is added This must be done slowly as buffer will also cause the pH to rise As an approximate rule every increase of 20ppm of TA will also cause a 0 1 rise in pH Once buffer is added it should be left to mix in the pool for a few hours before reducing the pH Phosphates and Nitrates Phosphate and ammonia nitrogen will make your garden green and they will do the same thing to your pool Check for phosphates and add phosphate remover if necessary Don t let fertiliser get into your pool Phosphates are also in some cleaning products check the label if using around your pool Metals Metals such as iron and copper will break down the polymers in the AquaFresh liquids Make sure there are no metals in the pool before starting the system Page 6 Pool Chemical Safety Your AquaFresh feeds a solution of Sanitiser and Enhance into your pool to
3. Filter requires backwashing Multi electrode probe may require cleaning see page 24 for details Injector nozzle is blocked If each of these factors is addressed the AquaFresh will dose the pool with acid until the set level is achieved at which point the status indicator will revert to green and the warning will no longer be shown on the LCD Note that TA reduces as acid is added over time Page 20 Maintenance Like all equipment the AquaFresh will look better and last longer if it is maintained and operated in accordance with these instructions The AquaFresh Power Supply The Power Supply has been design for operation in full sun and weather However it will benefit from being under cover There is little maintenance required however there are some Do s and Don ts Don t Install it in a small sealed enclosure so it does not overheat Install it in a very hot unventilated shed so it does not overheat Allow insects to nest in the unit because they will prevent it from functioning Install corrosive chemical drums under or close to the unit to prevent corrosion Forget about the unit once installed it should be checked regularly to ensure that it is working for you Do e Install it as per the instructions e Check it regularly e Make sure the pool balance is checked regularly Cleaning the optional Multi electrode Probe If the AquaFresh is consistently giving readings different fr
4. extra Enhance can be SuperDosed as an algicide at the rate of 1000mL 50m Performance the oxidiser must be dosed at least once per fortnight at the rate of 50gr 10m 50 gr is approximately 1 5 cup measure As an example a 50 000 litre pool will require a cup of Performance each fortnight Notes 1 The filter system should always be running when the pool is being used 2 As the Sanitiser is a flocculating agent the filter will remove more fine debris from the pool and may require more frequent cleaning pH Control optional When chemicals are added to water the pH can change this is because most chemicals are not pH neutral In a concrete pool the pH will slowly rise due to the alkaline nature of the wall material It is important for comfort and safety to ensure that the pH remains in the correct range for the pool The pH of the water can be lowered by the addition of acid and your AquaFresh can do this automatically The AquaFresh multielectrode probe measures the pH of the water and the controller then doses the pool with small amounts of acid to keep the pH in the correct range Page 5 Initial pool balance Before you begin using the AquaFresh make sure your pool water is balanced as follows There must be no chlorine in the pool prior to starting the system Add chlorine reducer sodium thiosulphate to make sure all trace of chlorine is removed AquaFresh is not compatible with chlorine or bromine
5. time using a 24 hour clock shows timer information In the example above line 2 tells you that the unit is turned ON and will turn OFF automatically at 23 00 11pm displays AquaFresh feeding information In the example above line 3 tells you that the Sanitiser will begin feeding today displays the optional pH information In the example above line 4 tells you that the current pH is 7 5 with the unit set to provide 7 6 This system is turned off until the optional pH Control is added Page 12 AquaFresh Operational Buttons Your AquaFresh has 5 buttons that allow you to control the various functions available via the AquaFresh Menu system Optional Pool Light ON OFF Optional N Auxiliary ON OFF _ Each button is labelled with its primary function either on the button itself or adjacent to it Secondary functions are labelled within a curved white outline next to the relevant button The buttons are backlit to show which are active at any given time although the ESC OFF button is always available to take you back to the home screen ON Button Turn the System On Manually Press the ON button once to switch the AquaFresh and the pool pump on manually The AquaFresh will default back to AUTO and turn itself off automatically at the end of the next programmed FILTER CYCLE and this time will be displayed on the LCD Increasing Manual Run time in Hourly Increments Press the
6. warranty are in addition to other rights and remedies under a law in relation to the goods Pool Controls warrants all components of the AQUAFRESH Water Management System to be free from defects in material and or workmanship for a period of 2 years from the original date of purchase or installation Additional Pro rata Warranty on Multi electrodes Optional Probes Pool Controls warrants the AquaFresh Multi electrode Probe to be free from defects in material and or workmanship for a period of 2 years followed by 36 months pro rata warranty Exclusion for Wearing Parts This warranty does not extend to wearing parts in particular the squeeze tubes fitted in peristaltic dosing pumps Squeeze tubes should be replaced every six months by a suitably qualified technician Pool Controls is not liable for any failure of its products or other damage caused by failure of a squeeze tube that has been used for more than six months WARRANTY OBLIGATIONS OF POOL CONTROLS If a defect in workmanship or materials in any Pool Controls product covered by this warranty is discovered during the term of the warranty and provided the warranty holder follows the procedure set out below Pool Controls will at its option repair or replace that item PROCEDURE FOR CLAIMING UNDER THIS WARRANTY In order to claim under this warranty the warranty holder must e Contact Pool Controls Service as soon as possible after the discovery of the defect and in any e
7. AQUA BY LO CHLOR User Manual AquaFresh Chlorine Free System pool CONTROLS Head Office 20 Abrams Street Sales Service Ph 1300 550 010 Balcatia WA 6021 Facsimile 1300 895 231 Email sales poolcontrols com au Web www poolcontrols com au Email service poolcontrols com au Contents Manufacturers Warranty 2 Introducing the AquaFresh 4 How it Works 5 Initial Pool Balance 6 Pool Chemical Safety 7 Installation Guide amp Diagrams 8 Front Panel 13 Navigating the Menu System 14 Timer Menu 15 Sanitiser amp Enhance Menu 17 Optional pH Menu 18 Status Indicator Warnings and Safety Shutdowns 19 Maintenance 21 Troubleshooting 22 IMPORTANT If the power cord is damaged the unit must be returned to Pool Controls for repair Always read the instructions and warnings on chemical containers before using chemicals Serial NUMDeY 2 02ccccccescesseceeceeeeeeees Date of Installation c scseeeeeeeees Installed Dykinson ponensia Page 1 pool CONTROLS Manufacturer s Warranty Pool Controls products come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure The benefits under this
8. ON button repeatedly or hold the button down to increase the manual run time in hourly increments The run time is displayed on the LCD When the desired run time has been reached press the ENT button to confirm your selection and the system will commence operation ESC OFF Button Turn the System Off Manually If the AquaFresh and pool pump are running pressing this button will turn them off manually The AquaFresh will automatically turn on again at the start of the next FILTER CYCLE and this will be displayed on the LCD Return to Home Screen If you have unintentionally accessed a AquaFresh Menu that you don t actually require pressing the ESC OFF button allows you to return to the home screen at any time ENT Button Use this button to enter the AquaFresh Menu system and to access the various options in each Menu Use the Y UP and N DOWN buttons to scroll through menu options and when your desired menu option is displayed on the LCD press ENT to access that option Page 13 Y UP Button and Optional Pool Light If you have accessed the AquaFresh Menu by pressing the ENT button press the Y UP button to scroll upwards through the various menu options Some menu options will prompt a yes or no answer If you wish to answer yes press the Y UP button If your AquaFresh also controls your pool lighting optional you can turn the lights on or off manually by pressing the Y UP button For multi colo
9. YCLES allows for up to 4 Filter Cycles to be activated and is very useful for seasonal timer adjustments e AUX controls timed operation of auxiliary power outlet e FULL MANUAL ON or AUTO TIMER ON use when the AquaFresh is being run as a slave to another controller The AquaFresh unit is not recommended as a slave unit as it has dedicated dosing timing Page 14 Timer Menu Setting the time Once you have installed your AquaFresh and turned it on you will need to set the correct time on the AquaFresh 24 hour clock First access the Menu System by pressing the ENT button The LCD will display the word TIMER MENU Select this by pressing the ENT button once more Line 2 on the LCD will now read SET TIME HOURS Press ENT to select this option and then use the Y UP and N DOWN buttons to adjust the hours on the LCD Confirm the correct hours value by pressing ENT again The LCD will now show SET TIME MINUTES Adjust the minutes using the Y UP and N DOWN buttons When complete press ENT to return to normal operation ADJUST CYCLES Sub Menu Your AquaFresh has two filter cycles pre programmed as factory defaults as follows Filter Cycle 1 ON at 6 00 6am OFF at 08 00 8am Filter Cycle 2 ON at 18 00 6pm OFF at 20 00 8pm You can change the start and finish times of each filter cycle to meet your sanitiser requirements and to suit your lifestyle To adjust filter cycle start and finish times p
10. anually see below for how to do this Manual Light Operation If the AquaFresh is turned on the light can be turned on or off manually by pressing the Y UP button If you have multi coloured LED lights that cycle through different colours and requiring a power pulse to change effects you can hold down the Y UP button to cycle through the options and release when the desired colour or effect is achieved Page 16 Sanitiser amp Enhance Menus Accessing the Sanitiser Menu Access the AquaFresh Menu System by pressing ENT Use the Y UP or N DOWN button to scroll through the main menus until Sanitiser or Enhance MENU is displayed on the LCD Press ENT to select Manual Feed Having accessed the Sanitiser or Enhance menu the LCD will ask Manual Feed Y N Press Y UP to select and on dosing pump models the display with read FEED 5 mins 75mL You can increase the amount of the dose by pressing the Y UP button until the desired dose amount is displayed Note the dose volume displayed is an estimate only Press ENT and the peristaltic pump will commence feeding the Sanitiser liquid Enhance SuperDose Algicide dose The Enhance menu has a special super dose calculation that adds Enhance at the rate of 1000mL 50m This dose follows on from the Manual Feed simply answer N DOWN to the Manual Feed Y N and the question SuperDose Enhance will be asked followed by the amount to be added Simp
11. cribed above and press the N DOWN button when asked whether you wish to do a manual feed The LCD will then read ADJUST SET POINT Y N Press Y UP to select this option and then the LCD will display the current set point Adjust this using the Y UP or N DOWN buttons Confirm the adjusted set point by pressing ENT The new set point will then be displayed on the right hand side of line 3 of the LCD Calibration and Re setting Factory Defaults If your AquaFresh consistently displays a pH reading different from that obtained by manual testing with a quality test kit it may be necessary to re calibrate the multi electrode probe The instructions below assume the probe is measuring a pH of 7 8 Caution do NOT re calibrate the probe until identical pH readings have been obtained from at least three tests from around the pool You will need to calibrate the probe to the pH value obtained from these test kit results Enter the pH menu as described previously and press the N DOWN button when asked whether you want to do a manual feed and then again when asked whether you wish to adjust the set point The LCD will then read CALIBRATE PROBE Press Y UP to select this option and the LCD will read PROBE Ph 7 8 ADJUST TO 0 0 Use the Y UP button to increase the adjusted value to the required level Press ENT to confirm the adjustment and after a few seconds the AquaFresh will revert to normal operation and the home screen will di
12. er pool equipment These outlets are also timed so accessories can be set to come on and turn off automatically Installing the Injection Manifold Unplug the pool pump before installing the injection manifold The injection manifold may be installed on the return pressure or inlet Suction side of the pump but always after any accessories such as heaters The maximum pressure for dose pump operation is 100kPa do not install between the pump and the filter Page 8 4aSILINVS yal M0739 SLNIWJ NVYYYV JHL dO Y3HLIS NI GATIVISNI 38 NVO GIOJINVW NOILOSFNI IHL NOLLISOd TVOILY3A V NI G 31V901 38 SAVM1V LSNW 13AIMS NOLLOSCNI HLIM dV 9 SLIHM IHL NOIL JXIA MO14 DNIMOTIO4 YALV3H 100d JHL Hala diINNd 100d JHL 40 AGIs JUNSSIYAd L31LNO JHL NO G3TIVLSNI 38 LSNW G1O4INVW NOILOIFNI JHL NOLLVTIVLSNI G1O4INVW NOILOSPNI ANNOYS 440 wWOOSL WOSr JNNA ONISOG LNNOW munn YIWYOISNVYYL LH9I 100d Odd 3N18 G IOJINVW NOILIANI OL 3181SOd woes s 3AA AYYNIXNY Odd HOVIE SV 3SO19 SV dWNd ONISOG NOILISOd dWNd 100d Odd 03X Ni duing esog Hd jeuondo WVYOVIC NOILVTIVLSNI HSAYAVNOV SNOILJJNNO9 YIMOd HS3ausVNOV YIWYOISNVUL LHOIT Page 9 Chemical Drums Position the Sanitiser and Enhance chemical drums in a safe and secure location preferably close to the Aq
13. g Drum weights and Y pieces not shown Peristaltic pump set Also included in the box but not illustrated e User Manual e Injection manifold and bushes not shown e Mounting hardware raw plugs screws and paper template Page 4 How it works The AquaFresh system is installed with dosing pumps to feed a calculated metered dose of the Sanitiser and Enhance chemicals into the pool each week These chemicals are polymer based biocides and flocculating agents A third chemical Performance is an oxygen based oxidiser that could be described as a powdered hydrogen peroxide This is added by hand periodically to remove oxidisable contaminants from the pool Running the system When the AquaFresh system is first started the LCD screen will prompt the operator to check the time and day Then the pool volume must be set for the unit to calculate the dosing requirements Simply follow the prompts to enter the pool volume in cubic metres m 3 1 m 1000 litres If you make a mistake it can be corrected in the Advanced Menu area under Pool Menu Dosing Sanitiser Enhance and Performance The unit will automatically dose Sanitiser at the rate of 60mL 10m on the day selected when the unit is first installed It will then dose Enhance at the rate of 50mL 10m the next day Both of these chemicals can be manually dosed if needed If the pool is experiencing an algal bloom for example if the pool has some green patches
14. imer is backed up by a Real Time Clock RTC similar to those found in computers During a power failure the AquaFresh will keep time and maintain AutoMode functions If a Filter Cycle is active when power is returned the pump will be turned ON within 1 minute The AquaFresh will keep all its settings and will not need to be re programmed The AquaFresh is ideal for use in systems where repeated power cuts occur such as off peak power circuits and Queensland s Tarriff33 system Page 22
15. ly press Y UP to do the Super Dose Turning Sanitiser amp Enhance Control On or Off To disable the feed system or re enable it if it has been disabled you need to access the Sanitiser or Enhance menu and work your way through the questions pressing the N DOWN button in response to each question The LCD will then read ADJUST CONTROL TURN OFF Y N if the system is ON or ADJUST CONTROL TURN ON Y N if the system is OFF If you press Y UP the system will turn on or off depending on its current status If you answer N DOWN to either question the LCD will return to the home screen Page 17 Optional pH Menu Accessing the pH Menu Access the Menu System by pressing ENT Use the Y UP or N DOWN button to scroll through the main menu until pH MENU is displayed on the LCD Press ENT to select Manual Feed Having accessed the pH menu the LCD will ask Manual Feed Y N Press Y UP to select and the display will read FEED 5 mins 75mL You can increase the amount of the dose by pressing the Y UP button until the desired dose amount is displayed Note the dose volume displayed is an estimate only Press ENT and depending on which model you have either the solenoid valve or the peristaltic pump will commence feeding Adjusting the Set Point The pH Set Point is the pH that the AquaFresh will adjust your pool water to You can adjust the pH Set Point via the pH Menu Enter the pH Menu as des
16. maintain water hygiene These chemicals should not be diluted Read the instructions on the containers If you have selected the pH Control option you may need to dilute the acid to suit the size of your pool Your AquaFresh can work with either hydrochloric muriatic acid or sulphuric sold as low fume or no fume pool acid If you have a concrete pool consult your pool builder about which acid is recommended IMPORTANT SAFETY MEASURES e Always add concentrated chemicals to water not the other way around e Don t allow chemicals to mix dangerous highly corrosive fumes can be produced e Always wear protective clothing footwear gloves and eye protection when handling pool chemicals to avoid injury e Ifa spill occurs wash the affected area with fresh water immediately and seek medical attention e Work in a well ventilated area and avoid inhalation of fumes e Read and follow safety instructions on chemical drums Pool Shops Your AquaFresh system is not compatible with some pool chemicals Chlorine and bromine based products should not be added to the pool Metal based algicides will destroy the biocides in the AquaFresh system Always tell the Pool Shop staff that you have an AquaFresh pool The level of Sanitiser in your pool is checked by a Biguanide Test Page 7 Installation Guide The basic installation of the AquaFresh System with dosing pumps is shown on page 9 Choose a good locatio
17. n The AquaFresh is manufactured from weather resistant materials and is designed for operation in full sun and rain However your AquaFresh will benefit if it is protected from the weather The AquaFresh Power Supply should not be mounted close to where chemicals are stored eg acid as vapours from some chemicals are corrosive and may damage the electronic controls within the unit Insect intrusion particularly ants can cause problems with all equipment Ensure that the pool equipment area is kept free of insects as much as possible Insect intrusion is not covered under the warranty Installing the AquaFresh Power Supply Locate the AquaFresh Power Supply close to the filtration pump so that it may be connected easily Connect the AquaFresh Power Supply to the mains power outlet of the pool area and make sure this outlet meets all applicable Australian Standard at the time of installation Mount the AquaFresh Power Supply at least 1 5m above the ground and at least 3m from the pool water A mounting template has been provided with the AquaFresh that shows you where to place screws on either a wall or post The PUMP socket outlet in the base of the AquaFresh Power Supply is dedicated to the filtration pump only Do not use a double adaptor to connect another pump as this will overload the system and void warranty Your AquaFresh has two other power outlets on its base which can be used to run lighting or oth
18. o ensure other factors such as total alkalinity are within the correct range see page 6 for details and Performance the oxidiser has been added regularly Low pH Excess Acid If the pH of the water drops below significantly below the set point a red status indicator will be illuminated and the words LOW pH will be displayed on the LCD The AquaFresh will automatically prevent any further acid being added to the pool until the pH is brought back into the correct range by the addition of sodium carbonate or sodium bicarbonate Possible causes include e Manual overdosing Excessive rainfall Faulty peristaltic pump The multi electrode probe may require cleaning see page 24 for details Low Total Alkalinity Poor pool water circulation Page 19 Safety Shutdown If the pH falls below 5 8 the AquaFresh will shut down pump operation to ensure no more acid gets into the pool High pH Insufficient Acid If the pH rises significantly higher than the set point a red status indicator will be illuminated and the words HIGH pH will be displayed on the LCD Note that a high pH can cause scaling in concrete pools and can reduce bather comfort It is important to restore the pH balance as soon as possible by adding acid to the pool Possible causes include e The acid drum is empty e The pool has a new plaster lining very alkaline demanding more acid than can be supplied by the AquaFresh Faulty dosing pump
19. om those obtained from a test kit it may be necessary to clean the multi electrode To do this e Remove the probe from the injection point by twisting the bayonet or if fitted with a tapping band by unscrewing the retaining nut and remove the o ring e Holding the cable gently swirl the probe in a dilute solution of hydrochloric acid pool acid for two minutes e Rinse the probe in clean water and then replace it in the injection point making sure that the o ring is in place e Twist bayonet to lock or tighten nut with fingers Page 21 Trouble shooting Before requesting service you may wish to run through the check list below but feel free to call Pool Controls Service on 1300 550 010 or log a service call via our website www poolcontrols com au If there appears to be a problem with the pool 1 Check chemical drum levels Possibly do a small manual feed to ensure dosing pump s are working 2 Have you added any chemical additives recently Chlorine bromine and metal based algicides are not compatible with the AquaFresh system Check pool for phosphates and remove if necessary Is the unit turned on and operating the filter pump If the unit is not running at all check the fuse in the bottom of the unit OW 00 Operation Following a Power Failure The AquaFresh unit comes with a timer function built into the operating software The timer is a 24 hour type with quartz crystal control This T
20. ress ENT to access the AquaFresh Menu system Press ENT again to select the TIMER menu and then scroll down using the N DOWN button until ADJUST CYCLES is displayed on the LCD Select this option by pressing ENT and the LCD will show the start ON time of the filter cycle being adjusted Use the Y UP and N DOWN buttons to adjust the start time Press ENT to confirm your selection and then the LCD will show the end OFF time for that filter cycle Adjust the OFF time in the same way as the ON time and press ENT to confirm After ON and OFF times for the first filter cycle have been adjusted the ON time for the second filter cycle is shown on the LCD This can be adjusted in the same way or if you do not wish to make any changes simply press ENT to confirm the time shown on the LCD Follow the same process to either adjust or confirm the OFF time for the second filter cycle and once this has been confirmed the LCD will display the home screen Note an additional 2 filter cycles can be enabled and programmed via the Advanced Settings Menu For details on how to access this menu please refer to the Advanced Settings Manual available to download from www poolcontrols com au or call Pool Controls Service on 1300 550 010 Page 15 Running Times We recommend your system be operated for at least 4 hours per day and always run the system when using the pool AquaFresh Sanitiser and Enhance are added for sanitation but the fil
21. splay the new pH value Page 18 Adjust pH System On or Off To disable the pH System or re enable it if it has been disabled you need to access the pH menu and work your way through the MANUAL FEED ADJUST SET POINT and CALIBRATE PROBE questions pressing the N DOWN button in response to each question The LCD will then read ADJUST pH CONTROL TURN OFF Y N if the system is ON or ADJUST pH CONTROL TURN ON Y N if the system is OFF If you press Y UP the system will turn on or off depending on its current status If you answer N DOWN to either question the LCD will return to the home screen Note Turning off the supply of acid is not normally necessary and could lead to unbalanced pool water that is unsafe to swim in Pool Controls recommends that you seek advice from a qualified professional prior to disabling the pH system or call Pool Controls Service on 1300 550 010 AquaFresh Status Indicators Warnings and Safety Features Normal Operation Green Status Indicators When the AquaFresh is operating normally and optional pH readings are within the correct range a green status indicator will be illuminated and the LCD will indicate the readings Note it is the pool owner s responsibility to monitor the pool and periodically confirm the AquaFresh s readings with a good quality test kit Remember that the AquaFresh is only able to balance pH and add Sanitiser Enhance but you need t
22. t the outside of each drum and wrap several turns of PVC tape around the tubing above the drum lid so that the drum Y piece will just on the bottom of the drum Lower the Y piece and sinker into the drum and screw on the lid if the tube is tight in the lid do not tighten completely as the drum must be able to breathe The Optional pH Control The optional pH Control has a single dosing pump injection manifold Probe and a length of tube with suction fittings The AquaFresh comes with the pH Control system turned off It must be turned on before the control will operate See Adjust pH System On or Off on page 19 Page 10 Installing the optional pH Control parts Unplug the filter pump prior to installing the injection manifold The manifold should be installed after any accessories with the water flow in the correct direction The dosing pump needs to be installed in a similar manner to the dual peristaltic unit described on the previous page Connection The Probe and single dosing pump must be connected to the unit The connectors are under the front cover which is accessed by removing two screws in the cover bottom corners Always touch connectors with clean dry hands wetness can interfere with readings from the probe f T Single Pump optional
23. ter is needed to remove pollutant particles dust sand etc and keep the water looking good The filter must operate for a reasonable number of hours per day to remove these pollutants If there are adverse local conditions such as windborne dust and debris you will likely need to operate the system for longer periods to adequately filter the water Optional LIGHT Timer Sub Menu You can use your AquaFresh to turn your pool or garden lighting on and off automatically you can set the ON and OFF times using the light timer menu Press ENT to access the AquaFresh Menu system Press ENT again to select the TIMER menu and then scroll down using the N DOWN button until LIGHT MENU is displayed on the LCD Line 2 on the LCD will now read AUTO Y N To enable automatic light operation press the Y UP button Line2 will read Auto ON for short period before displaying ON hh mm Adjust the ON time using the Y UP and N DOWN buttons and confirm by pressing ENT The LCD will now prompt you to set the OFF time which is accomplished using the Y UP and N DOWN buttons as before Press ENT to confirm the new OFF time and the LCD will return to the home screen To disable automatic light operation access the LIGHT menu in the way described above and when asked AUTO Y N press the N DOWN button Line 2 will read Auto OFF for short period then the system will return to normal operation and the light can only be operated m
24. the prior written consent of Pool Controls Pool Controls is not responsible for any cost of freight or transportation to or from its Service Department Pool Controls is not liable under this warranty if the installation of the Pool Controls product was not carried out by a suitably qualified technician To the extent permitted by law Pool Controls is not liable for any incidental or consequential loss incurred in connection with the removal or replacement of the Pool Controls product under this warranty To the extent permitted by law Pool Controls disclaims all other warranties either express or implied including but not limited to implied warranties of merchantability and fitness for a particular purpose with regard to Pool Controls products parts and or any accompanying written materials REGISTER YOUR WARRANTY NOW Go to www poolcontrols com au click on the warranty registration tab to fill in your details CONTACT POOL CONTROLS Pool Controls is based at 20 Abrams Street Balcatta Western Australia We also have service technicians based in NSW Queensland and Victoria Service Email service poolcontrols com au Service Phone 1300 550 010 Page 3 Introducing the AquaFresh Dosing Puma sysient What s in the box The image above shows the main parts of the AquaFresh Water Management System clockwise from top left e Mounting brackets top and bottom AquaFresh Power Supply and Mains Cable Tubin
25. uaFresh Note that drums of acid for the optional pH Control will need to be at least 2 metres from the unit due to possibly corrosive vapours Small weights and Y pieces are supplied to allow the tubing to sit on the bottom of the Sanitiser and Enhance drums The optional pH Control uses a different suction point see the following information Installing the Peristaltic Pumps Mount the dual peristaltic pump unit adjacent to the AquaFresh Power Supply as it is hard wired to this power supply Cut lengths of tubing that will reach from the base of each peristaltic pump to the injection manifold Connect one end of the tubing to the outlet side of the peristaltic pump the direction of flow is indicated by an arrow on the front cover of the pump Connect the other end of the tube to the injection point on the injection manifold Cut another length of tubing that will reach from the base of the peristaltic pump to the base of the chemical drum Connect the one end of this tube to the inlet side of the peristaltic pump the direction of flow is indicated by an arrow on the front cover of each peristaltic pump Drill an 10mm hole in the lids of the chemical drums and pass the tubing through the hole in the drum lid Place a sinker on to the end of the tubing that will be in the drum and then attach the Y piece Note that the Y piece must sit on the bottom of the drum Before placing the tubing into the drum measure the tubing agains
26. ured lights hold the Y UP button down to cycle through the various colours and release once the desired colour is reached Navigating the AquaFresh Menu System There are four aspects to the general AquaFresh Menu system the Timer Menu the Sanitiser and Enhance Menus and the pH Menu for optional pH Control Access the AquaFresh Menu system by pressing the ENT button and following the prompts on the LCD If you find you have ended up in a part of the Menu system unintentionally you can return to the Home Screen by pressing the ESC OFF button at any time Use the Y UP and N DOWN buttons to scroll through the various menu options until the desired option is displayed on the LCD Use the ENT button to confirm that you wish to select that option Once accessed use the Y UP and N DOWN buttons to adjust operational settings up or down and confirm adjustments by pressing ENT To cancel any adjustments simply press ESC OFF to return to the Home Screen Advanced Settings Menu If you are interested in learning more about additional functionality of your AquaFresh a detailed Advanced Settings Manual is available to download from the Pool Controls website www poolcontrols com au or call Pool Controls Service on 1300 550 010 for further information Advanced Settings comprise e POOL used to store information on pool volume and whether it is concrete or fibreglass e SYSTEM DATA shows service information e FILTER C
27. vent within the relevant warranty period e Provide proof of purchase and confirm date of installation e Confirm that the installation was completed by a suitably qualified technician as set out in the installation manual and e f required arrange for the relevant Pool Controls product to be returned to Pool Controls for repair and the warranty holder is responsible for the cost and risk of any freight or transportation to and from Pool Controls Page 2 CALL OUT FEES This is a Back to Base Warranty which means that if the Pool Controls product needs to be serviced replaced or repaired at a place other than Pool Controls premises a call out fee will be charged to cover the cost of travel by an authorised Pool Controls technician Please note that this call out fee will NOT be charged when the relevant Pool Controls product is returned to Pool Controls for repair If an authorised Pool Controls technician repairs or replaces a Pool Controls Product and this warranty does NOT apply a fee for labour and parts supplied will be charged in addition to the call out fee If the Pool Controls product needs to be returned for repairs under this warranty the warranty holder is responsible for the cost and risk of any freight or transportation to and from Pool Controls WARRANTY EXCLUSIONS This warranty extends to the original owner only beginning on the date of installation and is not enforceable by any other party without
Download Pdf Manuals
Related Search