User Manual KI6102 series PON Power Meter
Contents
1. 0 200 Accuracy Uncertainty dB 0 5 Polarization Dependent Loss lt 0 25 dB Linearity dB 0 1 Through Insertion Loss dB 413 Resolution 0 01dB Unit dBm xW Storage capacity 99 items Auto backlight off time 30 seconds Auto power off time 10 minutes Battery 7 4V 1000mAH rechargeable Lithium battery or dry battery Continuous working 18 hours for rechargeable Lithium battery approx 18 hours for dry battery Operating temperature 10 60 C Storage Temperature 25 70 C Dimensions mm 200 90 43 Weight g approx 330 KI6102 PON Power Meter User Manual Revision 5 Page 5 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 4 Safety Take appropriate eye safe precautions when handling live fibre Avoid condensation The instrument is resistant to normal dust and moisture however it is not waterproof If moisture gets into the instrument remove the batteries and dry it out carefully for at least one hour before using it again Storage During prolonged storage remove batteries to eliminate the possibility of acid leakage Use only high quality batteries KI6102 PON Power Meter User Manual Revision 5 Page 6 of 12 KINGFISHER INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 5 Configuration Ports PON POWER METER Sheath Keys Figure 1 Front view KI6102 PON Pow2. the displayed measurement unit will change to dB Press F2 to exit Relative Measurement Mode 6 3 Threshold setup 6 3 1 At Main Interface display press and hold A to enter Threshold Management Interface 6 3 2 Choose a threshold group number from 01 02 03 using A Y 6 3 3 Under the chosen threshold group use lt gt to select wavelength from 1310 1490 1550 nm KI6102 PON Power Meter User Manual Revision 5 Page 9 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 6 3 4 Once a wavelength is selected press and hold OK to enter Threshold Editing Mode Use lt gt to select digit position to be edited the selected digit position will be blinking Use A W to edit value of selected digit position and W to edit the sign of the set values Set edit the 3 thresholds as shown below displayed on screen with the desired values ALARM labeled as on display PASS labeled as V on display FAIL labeled as x on display Press OK to save settings note that settings edited with inappropriate threshold values will not be saved Use lt gt to select next wavelength and repeat the steps above to have its threshold levels set Press OFF to exit Threshold Editing Mode The Threshold Management Interface or Threshold Editing Mode will exit automatically if no subsequent key is pressed 10 sec after being selected Activating de activating p
3. INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter User Manual KI6102 series PON Power Meter Warranty Information in this manual is given in good faith for the benefit of the user It cannot be used as the basis for claims against Kingfisher International or its representatives if accidental damage or inconvenience results from use or attempted repair of the equipment This Kingfisher International product is guaranteed against defective components and workmanship for a period of 1 year from the date of delivery unless specifically stated in the original purchase contract or agreement This warranty excludes optical connectors or incorrect use The warranty will be voided if the following instance happens 1 Opening the instrument 2 The instrument has been immersed in water or subjected to extreme environmental conditions Liability is limited solely to repair of the equipment rer Optic Tes Boom Manutacturer KI6102 PON Power Meter CONTENTS User Manual oriin ee A ee E 1 KI6102 series PON Power Meter rssrnnnnnnnnnvnnnnnvnnnnnnnnnvnnnnnvnnnnnnnnnnnnnnnenn 1 1 SUI ANY EE EEE A E ie api ceeded Reese eee 3 2 Main TOATUL EE EE SN 4 3 Technical specifications rrrnnnanvrnnnnavvnnnnnnvnnennnnnennnnnnnennnnnnnevennnnnenennnnnennr 5 4 Safely sunne 6 5 Gonfhlguraton msinyslmmibnbmesmmrnddsrinvnim vi 7 6 Operation instruction runarerunsvnnnnennnnnnnnnnvnnnnvnnnnnnvnnnnnnnnnnnnnnnnnnn
4. atchcord External power supply charger Software CD USB cable Cleaning cotton stick pack Quantity 1 PPPRPPRPRB If require select from the option part number list below to order suitable AC power adapter plug Description P N AC Power Adapter Plug US to UK OPT093 AC Power Adapter Plug US to AUS OPT094 AC Power Adapter Plug US to EUR OPT095 KI6102 PON Power Meter User Manual Revision 5 Page 12 of 12
5. en with date record number and time information Press and hold OK to delete all records The Record Browsing Mode will exit automatically if no subsequent key is pressed 10 sec after it was selected 6 7 Battery under voltage When battery voltage drops below 6 7V for Lithium battery battery indicator will be displayed and instrument will beep for a short instant e before powering off automatically Recharging takes 4 6 hours The charging indicator on charger turns green when instrument is fully charged KI6102 PON Power Meter User Manual Revision 5 Page 11 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 7 Maintenance Keep the sensors surfaces clean and free of dust or other contaminant by cleaning them regularly Do not use unclean or nonstandard adapters Change adapter carefully if necessary and keep any spare adapter in dirt dust free environment When the instrument is not in use keep the optical connectors covered with dust caps at all the time Exposing the sensor for a long period of time will allow dust to be accumulated on surface of the sensor this will in turn result in measurement inaccuracy Consider leaving test cords connected to the PON meter at all times This will prolong the life of the instrument ONT amp OLT connectors 8 Shipment Content Description CWDM Power meter User manual Soft carry pouch SC APC SC APC or SC PC SC PC P
6. er Meter User Manual Revision 5 Page 7 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter ONT Port OLT Port Figure 2 Top View ONT interface Upstream 1310nm signal test port OLT interface Downstream 1490 1550 nm signal test port Charging Hole USB Port Dust Cap Figure 3 Side View USB Port Communicate with the management software via USB connector Charging Hole Insert connector of the charger to charge instrument KI6102 PON Power Meter User Manual Revision 5 Page 8 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 6 Operation instruction 6 1 ON OFF Instrument Press and hold ON to turn instrument ON The Main Interface will be displayed on screen see Figure 1 of page 7 The instrument is now ready for measurement The symbol f indicates that the instrument is factory calibrated Press and hold OFF to turn instrument OFF At Main Interface display after powering up Press F2 to select measurement unit dBm or xW Press F1 and the blinking symbol indicates that instrument is in Record Saving Mode Press OK to save record or press OFF to exit without saving The Record Saving Mode will exit automatically if no subsequent key is pressed 10 sec after F1 99 records can be stored 6 2 Relative value differential loss At Main Interface display press and hold V to enter Relative Measurement Mode
7. nnnnnnnennnnnnn 9 6 1 ON OFF Instrument eernronannvnnonvvnrorrvnnnrrnnnnrnnenvnnrrrrennnrnnsnnnnnennenenn 9 6 2 Relative value differential IOSS rrrnnnnnvnrnnnnnvnrnnnnnnnrnnnnrnnrnnnrrn ann 9 6 3 Threshold setup uavnasaiasarin nu nim venmenbene 9 6 4 Time seting noscere aa T 11 6 5 Auto POWer OT orenian A AARAA A dive 11 6 6 Record browsing and management runnnrrnnnnnnrnnnnnnnvnnnnrnnrnnenennnn 11 6 7 Battery under voltage cccececeeeseeeeeceeeeeeeeeseneaeeeeeeeeeeeestaeeeeess 11 7 Maintenance srerrnnnnvennnnnnvnnnnnnnvnnennnnvnnnnnnnvnnennnnnnnnnnnnnenennnnnenennnnnnnennn 12 8 Shipment Content rnnnnnnnvnnnnnvnnnnnnnnnvvnnnnvnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnnn 12 KI6102 PON Power Meter User Manual Revision 5 Page 2 of 12 KINGFISHER INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 1 Summary This PON Power Meter is specially designed for PON network construction and maintenance It can be connected between OLT and ONT The voice data video signals 1310 1490 1550 nm online can be measured synchronously and the respective optical power values can be displayed on the instrument The special Burst Mode measurement function enable accurate burst optical power measurement of upstream 1310nm signal Pass fail analysis can be done conveniently with the multiple user adjustable thresholds for each wavelength The fast speed instrument adopts a 32 bi
8. ower measurement with pass fail display mode At Main Interface display press and hold A to enter Threshold Management Interface Choose a threshold group number from 01 02 03 using A W Press OK to activate the pass fail display mode The chosen threshold group number will be displayed on screen at a position in between date and time information Press and hold OK to de activate pass fail display mode KI6102 PON Power Meter User Manual Revision 5 Page 10 of 12 GFISHER INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 6 4 Time setting At Main Interface display press and hold gt to enter Time Setting Mode use lt gt to select position to be edited the selected position will be blinking Use A V to edit the value of the selected position Press OK to save changes or press OFF to exit Time Setting Mode without saving The Time Setting Mode will exit automatically if no subsequent key is pressed 10 sec after it was selected 6 5 Auto power off At Main Interface display press OFF to disabled or enable Auto Power Off Mode When Auto Power Mode is enabled the symbol will be displayed on screen The instrument is defaulted to Auto Power Off Mode when it is first turned on 6 6 Record browsing and management At Main Interface display press and hold lt 4 to enter Record Browsing Mode Use A V to choose record The chosen record is displayed on scre
9. t CPU which is low in power consumption The overall low power consumption design and the user friendly operation interfaces of the instrument make test measurements easier and more convenient The instrument is a useful onsite test tool for operators and engineers involving in PON network maintenance KI6102 PON Power Meter User Manual Revision 5 Page 3 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 2 Main features e Handheld easy to operate e Able to measure power for 3 wavelengths 1490nm 1550nm 1310nm synchronously e Able to test Burst Mode upstream wavelength 1310nm e 3 groups of programmable threshold values for pass fail analysis e Choice for relative or absolute power measurement mode e Internal memory and download for 99 tests e Remote setting of thresholds upload data and calibrate wavelength by management software e Power saving design with auto backlit and instrument shut off features e Real time clock display KI6102 PON Power Meter User Manual Revision 5 Page 4 of 12 INTERNATIONAL Fiber Optic Test Equipment Manufacturer KI6102 PON Power Meter 3 Technical specifications Standard 1310 1490 1550 wavelengths upstream test downstream test downstream test Pass zone nm 1260 1360 1470 1505 1535 1570 Range dBm 40 10 45 10 45 23 Isolation 1310nm dB oat 740 Isolation 1490nm aB gi oa Isolation 1550nm dB
Download Pdf Manuals
Related Search