2.4GHz WIRELESS A/V/ALARM RECEIVER USER MANUAL
Contents
1. 2 4GHz WIRELESS A V ALARM RECEIVER USER MANUAL 1 s O AOO Panel View A V ALARM with D Ary lan 2 4G RX veo scrawace s im apressinc NZ Z DC 12V IN 500mA s e a m p ID la I 0 _ ne HEA HHHRB o D e S E O i ya POWER DISARM Leda 12E ai ALARM OUT OUT OUT J CH SELECT ID ALARM lax 4 DC 12V IN Power input DC 12V 500mA ALARM OUT Once triggered the built in buzzer and alarm remains on for a 20 sec time This port could be connected to alarm devices e g Siren Flashing Unit AUDIO RCA female for audio signal output VIDEO BNC female for video signal output POWER STATE LED Indicated to power on or ARM and RF link status Power State LED High speed Flashing RF Loss Waiting TX Link Low Speed Flashing DISARM DISARM at RX receiver s side only CH SELECT 1 2 3 4 2 4GHz receiver has two receiving modes one is single channel receiving and the other is scan mode for multi channel receiving In scan mode receiver shift to next channel per 3 seconds Note Alarm signal output is disabled when the receiver is operating in scan mode CHANNEL CH SELECT SCAN MODE CH SELECT aioe ee 1 2 ii 1 2 d 4 a P KOES itt n M f cH1 cH4 lle faalala 8 ID AND ALARM MUTE ID address setting is use for paring with 2 4G TX transmitters lt must be make the same code setting to link transmitter and receiver each other The alarm mute func2. digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body 3 Any changes or modifications including the antennas made to this device that are not expressly approved by the manufacturer may void
3. the user s authority to operate the equipment Q2010 05 17
4. tion is use for muting built in buzzer and disables the alarm output at RX receiver s side only 9 ANT SMA connector for connected to 2 4 GHz antenna and built in 3 3V 25mA bias tee circuit for an active antenna REMARK When the frequency channels have the interference adjust antenna or change the channel of transmitter and don t close to 802 11 a b g AP router and other 2 4GHz devices Note Please keep 3 5 meter away 2 Caution for Installation 2 1 Be careful never let any water in this equipment 2 2 f necessary use a soft cloth moistened with alcohol to wipe off the dust 2 3 Be extra careful not to shake the unit 2 4 Avoid places where temperatures exceed 50 C or higher 2 5 Avoid places where there are frequent vibrations or shocks 2 6 When any abnormalities occur make sure to unplug the unit and contact your local dealer 3 Packing 3 1 Receiver x1 3 2 Antenna x 1 3 3 User manual x1 3 4 Screws x4 3 5 Plastic Conical Anchor x4 3 6 Power Adaptor x1 Option 4 Specification 2468 MHz Minimum Receiver Sensitivity 82dBm Type POWER SUPPLY DC12V 500mA Adaptor CURRENT CONSUMPTION 250mA Typical VIDEO OUTPUT 1 0 Vp p Composite 75Q AUDIO OUTPUT 2 0 Vp p Typical 2 7 Vp p Max 600 ALARM OUTPUT NC NO COM Dry Contact Contact Rating AC 125V 0 5A DC 24V 1A DIMENSIONS without Antenna FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B
Download Pdf Manuals
Related Search