Home

FGW Modem Module User's Manual

1. Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 5 Caution 5 1 Communications Settings Some modems have fixed settings 10 bits for character bits Select the one of the 4 settings below for the communications settings Start bits Data bits Parity Stop bits en 1 fixed 7 Even 1 10 1 fixed 7 Odd 1 10 1 fixed 7 None 2 10 1 fixed 8 None 1 10 Confirm that the communications settings of the computer and the PLC match except the speed Refer to the PLC manual to see how to set the communications settings for the PLC 5 2 Speed Setting You can set the speed for the computer with the communications settings of Modem Module and set the speed at the PLC with the PLC modem settings utility The speed setting will vary between modems Modem Modem 33600 bps Computer Modem 19200 bps Modem PLC 9600 bps Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 5 3 Connecting the PLC Modem Prepare the cable according to the figures below to connect the modem to the PLC The cable included with the modem works to connect to a computer but not a PLC PLC CPU unit 9 Connector hood Connector hood FG FG FG SD RD SD RD For wiring details refer to the modem and PLC manuals 5 4 Send the AT Command T
2. to make the telephone number easy to identify 4 Click on the Modem Setup button in the telephone number setup dialog to start the modem settings dialog Select the modem in the Modem to use field and set the communication settings to match the settings of the remote PLC Standard Modem Properties E Ea General Connection Options Connection preferences Data bits Parity Stop bits 2 Call preferences MY wait for dial tone before dialing Gencel the calli not conmmected within SeCH Disconnects callii idie for more than mir Advanced Cancel 5 Click the Unit setup button in the telephone number setup dialog to start the modem settings dialog Select the COM port which connecting the Modem COM1 Serial Unit Properties x About Network Communication Unit Nodes Lines Hode no Unit no COM1 COM 31 24 El com 31 25 UlcoM3 COM3 31 26 ClcomM4 COM4 31 27 Add Delete ze the check boses to select lines 6 Confirm that the new telephone number appears in the telephone numbers dialog 7 Click OK to finish the telephone number setup Click cancel to cancel the settings and quit Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 4 2 Serial Communications Driver Settings 1 Dial the destination After the telephone number is registered Click the Dial button and start dia
3. FinsGateway Modem Module User s Manual FinsGateway Modem Module User s Manual First Version November 1999 OMRON Corporation FinsGateway Modem Module User s Manual CONTENTS 1 1HEFOQUE ON ai 3 2 System Requifements u einen 4 3 SErcNG ENGR LE MOJEN ee A 5 3 1 Communications Settings for the PLC Modem uussss202snnnnnnnennnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 5 3 2 Serial Communications Driver Settings uuuesnnnsnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnn 7 OCIA NON aa E ATE 8 4 1 Registering Telephone NUMberS s ssssssssssrrrrrrsessrrrrrrssrnrrnrenssrnnrrnssrnnrnrreosrnnnrrrennnrnreosnnnrnrrrnreeent 8 4 2 Serial Communications Driver SettingS uesnsessnnneeeennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnsnnnnnnnnnn 10 4 3 CHOSE TING LINE E a E EAA 11 IC AUTON een 12 Dk COMMUNICSEIONS SEUNS ne ie 12 9 2 9 Dee S ELLING re dee een endende caselsten dad Scie vncl deny 12 3 3 Conhecting tne PLCE Modem ns ne 13 3A SOM NE AT EONMande een einher 13 O Kr OUDLESNOOLING in eier 14 Copyright OMRON Corporation 1995 1996 1998 1999 All Rights Reserved FinsGateway was developed using Microsoft Visual C Version 5 0 and Version 4 1 Borland Delphi Version 2 0 and Microsoft FrontPage98 Copyrights of the FinsGateway manual and software are owned by OMRON Corporation except the following items FinsGateway is released containing the followin
4. are recommended to operate the Modem Module Sucre GAG NT PREECE Pentium 200hMHz or higher HIME or higher Microsoft Windows NT Windows35 or Windows 98 FinsGaleway Ver2 0 of higher Modem for Windows Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 3 Setting the PLC Modem 3 1 Communications Settings for the PLC Modem Modems can detect the communication settings automatically to communicate with the computer when the computer sends the AT command to the modem That is why you do not need to set the communications settings for the computer modem However the PLC modem cannot detect the communications settings because PLC is not a computer and does not send the AT command to the modem The communications settings for the PLC modem must match the settings of the computer modem and the PLC The communications settings for the PLC modem must match the settings of the computer modem and the PLC Modems can detect the communications settings automatically to communicate with the computer when the computer sends the AT command to the modem Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 1 Plug the PLC modem into the COM port of the computer 2 Click on the Start button point to Programs point to FinsGateway and point to PLC Modem Setup Receive Modem Setup se
5. g items copyrighted by Microsoft Corporation These are ATL DLL MFC42 DLL MSVCRT DLL MSVCP50 dIl and OLEAUT32 dIl These modules included in FinsGateway are redistributed based on a license agreement between Microsoft Corporation and OMRON Corporation Under this license agreement these modules cannot be distributed by the customer FINS and FinsGateway are trademarks of OMRON Corporation Microsoft Windows WindowsNT and Visual C are registered trademarks of Microsoft Corporation Pentium and Intel are registered trademarks of Intel Corporation IBM is aregistered trademark of International Business Machines Corporation All corporate names and product names mentioned in this manual are trademarks or registered trademarks of each company TM The symbols and are omitted in this document Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 1 Introduction The Modem Module is an add on software for FinsGateway remote communication You can develop a remote PLC data acquisition application quickly and easily using the modem module Analog Phone Line FinsGateway Modem Module Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 2 System Requirements The Modem Module is an add on software for FinsGateway Therefore the environment must support the operation of FinsGateway The following system specifications
6. he PLC modem setup utility may not work for old modems If the utility does not work send the AT command to set it Send any AT command using the PLC modem setup utility See the modem manual for the setting details AT Command gt gt gt lt Command x Function AT Command AT Gacur Set the number of rings for auto answer ATSO 1 Response The example shows setting 1 ring Save the settings in non volatile RAM The example is saving the settings to profile 0 on a Restore Defaults Exit Select the profile to load when the modem is AT amp YO pe turned on The example is loading profile 0 Flow control or the CD DR ER signal control settings may be required for the modem See the modem manual and determine the AT commands to set them Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 6 Troubleshooting Is the equipment turned on Confirm that that the modem and the PLC are turned on Is the equipment all connected Confirm that the modems are connected to the computer and the PLC Confirm that the modem and the telephone lines are wired Refer to the modem manual for the wiring Is it the right cable A special cable is required to connect the PLC and the modem Prepare the right cable Is the right type selected for the telephone line Confirm that the right type of telephone line is selected tone dialing or pulse dialing Is the PLC m
7. ling You can monitor status and perform one shot communications with a remote PLC after dialing is completed successfully gt FgwTapilaller Pale ES Number to dial 01 2345 6789 Dial property Device Standard Modem Modem setup Serial Unit com Unit setup Line Status Update Close Da The line status dialog appears when dialing After dialing is completed successfully the dialog is minimized automatically t FinsGateway TAPI Call Device OMRON_MES6140_ 56h FAs DATS MOD Number to E Status LINECALLSTATE_PROCEEDING Message Now dialing Click the icon to see the dialog again sFewTapicall E Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 4 3 Close the Line 1 Click the Hang up button in the FgwTapiCaller Fowl apiCaller ON Ea Number to dial 01 2345 6783 Dial property Device Standard Modem ki Modem setup serial Unit com Unit setup Line Status Update Close Da Closing the Line Manually You can also close the line by clicking on the Disconnect button in the line status dialog FinsGateway TAPI Call Device Standard Modem Number to T01 2345 6 759 Status LINELALLSTATE_FR LEEDING Message Now dialing Perrere ree eee ees Close the line manually Tauununannnunnmnunnnnunnunnununnnn
8. odem set Set the PLC modem The modem will not work with the default settings The settings will be erased if the modem has been turned off for a long time Set the modem again Is the telephone number right Is Modem Module dialing the right number Do the communications settings of the PLC and the modem match Confirm that the communications settings of the PLC and the modem match Are the modem settings right Confirm that the right modem is selected if multiple modems are installed Confirm that the modem is connected to the right COM port Confirm that the COM port for the internal modem matches the settings Copyright OMRON Corporation 1999 All Rights Reserved
9. on Register a telephone number to identify each destination modem and PLC 4 1 Registering Telephone Numbers 1 FgwTapiCaller Settings Click on the Start button point to Programs point to FinsGateway and point to FgwTapiCaller FgwT apiCaller Mm E Number to dial 01 2345 6789 Dial property Device Standard Modem z Modem setup Serial Unit COM1 bi Unit setup Line Status Update Du cose 2 Select Phone Line Type Click on the Dialing Properties button Select Tone dialing or Pulse dialing in the Dialing Properties dialog to set the dialing type Dialing Properties EEG My Locations Where am am dialing from IDEAMI The area code is 048 am in United States of America 1 Click the Tone dialing or Pulse dialing in the Dialing Properties dialog to select the dialing type m How dial from this location To access an outside line first dial E for local for long distance Dial using Calling Card V This location has call waiting To disable it dial The phone system at this location uses Tone dialing Pulse dialing Cancel Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 3 Type the name and the telephone number of the destination to call in the telephone number setup dialog You can enter a comma or in the telephone number box
10. tthe connection preferences for the modem connected directi ta the PLU LOM Fort COM Port i ie Connection Preterences et Default Baud Rate 3600 AT Commend Data Bits stop Bits Fari a Exit 3 Select the COM port for the modem in the COM port box 4 Select the communications settings in the dialog to match the communications settings of the PLC default BaudRate 9600bps Data Bits 7 Stop Bit 1 Parity Even 5 Click on the Set button The PLC modem setting is done Unplug the modem from the computer and plug it into the PLC Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 3 2 Serial Communications Driver Settings 1 Exit PLC Reporter if it is running 2 Click on the Start button point to Programs point to FinsGateway and point to Serial Communications Setup 3 Click the Communications Line tab and select the check box of the COM port for the modem to add the phone line COM1 Seral Unit Properties About Network Communication Unit Nodes Lines Node noa Unit no COMI COM y 24 El comz a 25 CICOM3 COM3 y 26 CIcOM4 COM4 ci 27 Add Delete Use the check boxes to select lines 4 Click OK to close the dialog 5 Set the network address for the added phone line if necessary Copyright OMRON Corporation 1999 All Rights Reserved FinsGateway Modem Module User s Manual 4 Operati

FGW Modem Module User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents