T80X Series Portable Multi-function Jump Starter User Manual
Contents
1. DIM ENTER LCD backlight Switch DC output voltage confirm During power on state press DIM ENTER to turn on off backlight and in Voltage select state press DIM ENTER to confirm the voltage DC output 2 323 Y Torch LED Control Key Press the key around 3 second to start torch LED the default setting is Normal mode If keeping press shortly you can choose 2 mode Normal Flash You can shut down the torch LED by press the key around 3 second Mode Description Normal means normal brightness Flash means Torch LED keep flash with frequency of 1Hz 2 3 4 e LED Warning light switch Press the key around 3 seconds to startled LED Warning light function The default setting is Traffic Fault Warning mode If keeping press shortly you can choose 3 mode Traffic Fault Warning SOS White Light Illumination You can shut down LED Warning light function by press the key for 3 seconds or closing the LED Warning light Mode Description Traffic Fault Warning means LEDs keep flash at frequency of 0 5Hz red LED flash twice and then white LEDs flash twice SOS means white LEDs keep flash 3 times at frequency of 1Hz then red LEDs Keep flash 3 times at frequency of 0 5Hz White Light Illumination means white LEDs keep lighting Note l Please shut off Warning LED Light first and close the cover after used Il The unit only support Torch and Warning LED light in one time Part 3 How to Jump Start your car a Warning Jump starting a car can cause se2. C output during the display flash Il If there is no load in one minute the unit will automatically power off Part 6 Technical Parameters Wo aw
3. T80X Series Portable Multi function Jump Starter User Manual Please read this manual before using this product Failure to do so can result in serious injury CONTENT Part 1 SAFETY amp MAINTAINANCE Part 2 PRODUCT INSTRUCTION Part 3 HOW TO JUMP START YOUR CAR Part 4 HOW TO CHARGE THE UNIT Part 5 HOW TO USE Multi Level VOLTAGE DC OUTPUT Part 6 TECHNICAL PARAMETERS Part 1 SAFETY 8 MAINTAINANCE GENERAL SAFETY RULES A WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may Result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS Thanks to use our T80X series Portable Vehicle Multi Function Jump Starter and before using it please read this manual carefully for reference a WARNING Before using this device please read the manual carefully and observe the following regulations strictly prohibit disassembling this device without authorization strictly prohibit placing this device near high magnetic field which will damage it and make it can t work well strictly prohibit making the device exposed to the rain or becoming damp which will cause interior short circuit and make the batter emit heat smoke be out of shape damage or even explode this device has large current discharge characteristic please prevent children from operating or playing it please fix this device well when placed in the back of a car to avoid affect drive safe
4. op rolling the charging is completed 4 2 Charging the unit in home Please connect the unit with 12V 1A AC adaptor to charge the unit and LCD screen will show the scroll bar which shows the unit is being charged If the scroll stop rolling the charging is completed Note Always charge on concrete or tile not on surfaces that are flammable or surfaces that could get heat damaged Diagram 5 Charging in the car Part 5 How to use Multi level Voltage DC Output 5 1 Power on off Please press DC SELECT key shortly to power on the unit when the unit is power off please press the key for a long time about 3 seconds to turn off the unit 5 2 Multi level Voltage DC Output The unit can support multi level DC voltage output apply for many kind of notebook or other consumer electronics device In power on state press 5 DC SELECT key shortly to select output voltage the display will be flashed when you adjust the voltage and the display will be stopped flashing when you press DIM ENTER key to confirm the output voltage Diagram 6 Multi Level DC Voltage Output 5 3 USB Output USB output standard is 5V 2 1A current max USB output can charge standard USB devices Please use the original USB line supplied by your device manufacturer to charge your device The unit can charge for many brand mobile phone PDA MP3 MP4 PSP MID GPS Digital Camera Bluetooth earphone iPhone iPod iPad and so on Note There is no D
5. rious injury if you are not careful If you are unsure of what you are doing at any point do not attempt to jump start your car Call your friendly roadside towing service for help instead When your car battery is power lack or the temperature is too low to start your car you can use this device to start your car as the following steps Step 1 Please ensure the engine battery is 12V if 6V or 24 Do not use with the unit Check the battery capacity level in the unit and then simply attach the jump leads red to red black to black to battery and the unit will automatically start delivering continuous power If your connection is inverse or unreliability the unit can t work If your connect is right The LCD screen will show the related information and the built in buzzer will long sound twice and then sound DIDI shortly twice every two second which means that the car is ready for start and please start your car soon r A N a Es ye da Diagram 3 Current output connect with car battery Note l Red cable connect with positive pole Il Black cable connect with negative pole Diagram 4 LCD Information after right connection Step 2 After right connection you can start your car in 60 second If you haven t do that in 60 seconds the unit will turn off automatically You have to break the connection between the unit and the car battery and then connect them again to start the jump function for 60 seconds After starting
6. ty this device is battery products so you d better charge it once within 3 month or change it once in half a year at least to extend the working life of lithium batteries strictly prohibit throwing this device in fire which will cause blast please deal with the scrap device according to related rule Don t deal with the built in battery as house refuse which will cause blast and pollution Part 2 Product Introduction 2 1 Appearance Description 008 00 Diagram 1 Front and profile side description 1 Torch ON OFF 5 DIM ENTER 9 LED warning light 2 Torch 6 USB output 10 EC5 output 3 Display 7 DC 12 19Voutput 11 LED warning light ON OFF 4 ON OFF DC SELECT 8 DC input 2 2 Display Description OQ 0 1 Battery capacity indicator 2 Jump starter indicator 3 Voltage indicator 4 USB output indicator Diagram 2 LCD display description 2 3 KEY and Function Description Setup Winzard 2 3 1 5 DC SELECT Power Switch DC Voltage select Please press the DC SELECT key to start portable power function when the unit is shut down After starting up the unit please press the key shortly then you can change the DC voltage output among 12V 19V and the display will be flashed press DIM ENTER key to confirm the output voltage and the display will be stopped flashing Press the 0 DC SELECT key for a long time about 3 second to turn off the unit Note There is no DC output during the display flash 2 3 2
7. your car please break the connection between the unit and the car battery and remove the alligator clip from the rear port The unit can automatically identify start jump status and power off automatically If the unit can t identify start jump status it will power off automatically in 60 seconds Another way you also can shut down the device by pressing 6 DC SELECT more than 3 seconds CAUTION 1 The unit only can be used for jump start car in emergency it can t replace the car battery 2 Please connect the alligator clip to car battery correctly red to red and black to black 3 When Voltage of the built in lithium battery is lower than the lowest Voltage to start jump a car the unit can t work 4 When the car battery voltage is lower than 3V the unit will treat the car battery as bad one and can t start automatically 5 When you disconnect the unit and the car battery please try to prevent the positive and negative touching otherwise there would be spark casuing potential safety hazard If you connect the positive and negative unconsciously the unit will power off automatically 6 Please choose the right mode for your car Part 4 How to charge the unit Before initial use it is necessary to completely charge the unit 4 1 Charging the unit in Car Please connect the unit and Car Cigarette Lighter with DC cable then the unit LCD screen will show the scroll bar which shows the unit is being charged If the scroll st
Download Pdf Manuals
Related Search