User's Manual - Dental Concepts
Contents
1. 1 Place the sealed protective bag in the patient s mouth in the required position for the image you wish to take The back of the protective bag the black side must face away from the X ray source Protective bag with imaging plate k 2 Select an exposure value appropriate for the exposure you are taking The unit can read im ages taken with exposure times from 0 05 to 0 63 seconds at 7 mA 3 Protect yourself from radiation and take the expo sure User s manual 8201052 9 Digora Optime 2 Standard Version Reading the imaging plate 1 Remove the sealed protective bag from the pa tient s mouth NOTE If a risk of cross contamination exists wash disinfect and dry the protective bag before open ing it 2 Open the sealed protective bag 3 Slide the plate cover and imaging plate out of the protective bag Keep the imaging plate in the plate cover so that you do not touch the imaging plate or allow it to be exposed to bright light Protective bag Plate cover and imaging plate ha gt 4 If unit door is closed and the GREEN light is flashing the unit is in the energy save mode Press the Start key The unit door will open the plate carrier will slide out and the GREEN light will stop flashing and remain on Plate carrier 10 User s manual 8201052 2 Standard Version Digora Optime CAUTION If the GREEN and YELLOW lights are both on itindicates that the unit is in the2. Erase mode DO NOT attempt to read an imaging plate when the unit is in the erase mode To exit the Erase mode press and hold down the Start key until the YELLOW light goes out LO Ce Me 5 Slide the imaging plate and plate cover into the plate carrier as far as they will go The back of the imaging plate the black side must face the plate carrier A magnet will hold the imaging plate in position Q Imaging plate and plate cover WRONG i Slide the plate cover off of the imaging plate leaving the imaging plate in position Plate cover gt WRONG Imaging plate User s manual 8201052 11 Digora Optime 12 2 Standard Version After the plate cover has been removed the plate carrier with imaging plate will automatically slide into the unit and the unit door will close The GREEN light will start to flash which indicates that the imaging plate is being read CAUTION If the plate carrier does not slide into the unit after the plate cover has been removed the imaging plate is misaligned or has been placed in the unit the wrong way round Re insert the imaging plate correctly A read out progress window will appear on the PC display After a few seconds the new image will appear on the patient card NOTE There is a metal disk on the rear of every imaging plate If this disk can be seen on the digital image it indicates that the imaging plate was exp
3. MUST be erased See section 3 Erasing an imaging plate for information on how to do this CAUTION When handling imaging plates plate covers and protective bags always take the appropriate hygiene measures and precautions to prevent cross contami nation Metal disk 1 Place the imaging plate you plan to use onto the long half of the plate cover The blue active side of the imaging plate must face the plate cover and the metal disk on the back of the imaging plate Long Ly Short must be positioned near the outer edge of the half half plate cover Plate cover Imaging plate Short half 77 2 Fold the short half of the plate cover over onto the y imaging plate Metal disk l 3 Slide the plate cover and imaging plate into the protective bag as far as it will go Make sure that the black side of the imaging plate the back is against the tape black side of the protective bag SIZE 1 2 3 CORRECT WRONG WRONG AN Protective Tape Imaging plate bag in cover CORRECT SES 8 User s manual 8201052 WRONG WRONG Pan pera ee 4 2 Standard Version Digora Optime 4 Remove the cover paper from the sealing tape Fold the flap over onto the sealing tape A score line on the front of the bag will help you to fold the flap PA Smooth the flap from the centre out to ensure that the seal does not wrinkle Cover paper Sealing tape Flap Taking an exposure using the imaging plate
4. anna 36 6 Maintenance repair and disposal oooooWoccccc 37 6 1 Maintenance Wee onta hate anina Me a Kes 37 602 REDA eanan eE E A EEEE E EE NA AR 37 6 3 oa ranee Aer ee Rio nner EEEE re 37 7 Symbols that appear on the UNI aa Bai 38 8 Technical Specifications Meoiiiiiii dm 39 cS oN mn ee 39 8 2 Imaging Paten ena ea eee ere 40 8 3 Computer SP SONATA em laa BEN BNN Emak 41 8 4 Main dimensions anccsicsncderdecenteciedsdaconetymnrnncindedns Genaaeasennedtanndsuhbadesdedeptndasnouce 42 IV User s manual 8201052 Introduction 1 Introduction 1 1 The Optime User s manual 8201052 Digora Optime This manual describes how to operate the Cranex Optime intraoral imaging plate unit The unit is designed to read 0 1 2 and 3 size intraoral imaging plates supplied by Soredex The unit works in conjunction with a PC in which compatible dental imaging software such as Digora for Windows 2 5 or above has been installed The Optime can be configured to work with a single PC the Standard version or in a shared environment where the unit is accessed from different PCs the Multi Connect version Only the manufacturer s authorized personnel are allowed to install and configure the Optime intraoral imaging plate unit Digora Optime Introduction 1 2 Warnings and precautions CAUTION CLASS 3B LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM CAUTION Use of controls or adjustments or performance of procedures other
5. fast flashing Unit is reading erasing an imaging plate YELLOW on Imaging software not opened or untransferred image in unit Open imaging software and retrieve the pending image if necessary YELLOW slow flashing There is no Ethernet link YELLOW fast flashing Unit carrying out its selftest User s manual 8201052 3 Multi Connect Version e M o e o RRO i e 9 Re M LN e User s manual 8201052 Digora Optime GREEN on YELLOW on Unit is in the Erase mode GREEN flashing YELLOW on Unit is in the Erase mode and is erasing an imaging plate GREEN on YELLOW flashing Unit is exiting the reserved mode If reguired again click the Multi connect icon to reserve the unit RED flashing ERROR Switch the unit off and then on again If the red light comes on again contact your dealer for help 21 Digora Optime 3 3 Using the unit 3 Multi Connect Version Preparing the image read out system 1 2 Switch on the PC that is connected to the unit Open Digora for Windows or the dental imaging software you are using If you are using the unit for the first time you may wish to check and or change the setup options See section 4 Setup options for more informa tion Open the patient card where you wish to place the new image or open a new patient card Press the Stand by key to switch the unit on The YELLOW stand by light will turn off and unit will carr
6. imaging plate ooooooooooWoo 9 Reading the imaging plate coco omooo one ana 10 Retrieve last image Le RR nnee enn 14 Image quality warning message ooooooWooooonananan 15 Removing imaging plates from the plate collector oooo 16 Shutting down INUL dee oa magma aman aa reenen 16 Erasing an Imaging Plate ee ea Aa ana 17 3 Optime Multi Connect Version ooooo Woo Woo 19 3 1 Main parts and COMMONS Lobak ea sae 19 3 2 Indicator WANA S ea ee Ban an Ra 20 S3 Usingthe N ee ne NN aa Tau SARC ieNSE 22 Preparing the image read out System ooooooo momo 22 Preparing the imaging plate nee aa anak ba Bana 23 Taking an exposure using the imaging plate oo oooooWoo oo 24 Reading the imaging plate ae esek aa Ou aan 25 Retrieve last image bhn aan aa mn aan en AE aa 29 Image quality warning message ooooooWoW oo mna 30 User s manual 8201052 lI Digora Optime Removing imaging plates from the plate collector 30 Shutting down NU ee ana aa an an ea en 31 Erasing an Imaging Paten nama animal gia Daan 31 4 Setup Options en area 34 4 1 Tooth numbering ibn aa ia diana SN AE Ha 34 Selecting the tooth numbering feature ooooooooW om 34 Using the tooth numbering feature oooooooW oo Woo Woo 34 re NN An A 35 4 3 Image Processing ni na ea an ne aer an 35 5 Cleaning and disinfecting the Unit 36 5 Cleaning the UNI ate mana mna 36 SAD CELA UN Ai
7. the rear of every imaging plate If this disk can be seen on the digital image it indicates that the imaging plate was exposed from the wrong side The image must be mirrored using dental imaging software 27 Digora Optime 28 3 Multi Connect Version IMPORTANT NOTE RETRIEVING IMAGES Ifan image is not transferred to the PC because of a network PC or software failure the image can be retrieved For information on how to do this see section Retrieve last image After the imaging plate has been read it will be erased and then automatically ejected from the unit into the plate collector After the imaging plate has been ejected the GREEN light will remain on and the unit door will stay open The unit is now ready to read the next imaging plate If no new imaging plate is inserted into the unit within a certain time period configured during installation the unit door will close and the unit will exit the reserved mode and enter the waiting mode A few seconds before the unit enters the waiting mode the YELLOW warning light will start to flash and the unit will start to beep User s manual 8201052 3 Multi Connect Version Digora Optime After a few seconds the plate carrier will slide back inside the unit the door will close the YEL LOW light will go out and the GREEN light will start to flash The unit is now in the wait mode bd Retrieve last image If the last i
8. 02 A2 2001 191mm x 221mm x 394mm 7 5in x 8 7in x 15 5in 7 kg 15 5 Ib 100 250 V 50 60 Hz Less than 1 5 A 40 um Super 64 um High 4 bits grayscale 10 Ip mm 12 5 Ip mm 4 3 7 6s Total processing time 9 22s UTP RJ 45 Ethernet required not supplied max 2 5m Connection to the PC must meet IEC 60601 1 and or corresponding IEC harmonized national standard 10 C 40 C 30 90 RH 700 1060 mbar Horizontal on a stable vibration free surface Storage transportation 10 C 50 C 0 90 RH 500 1080 mbar environment Image on screen time User s manual 8201052 39 Digora Optime 8 Technical Specifications 8 2 Imaging Plates Size Seo Size1 Sze2 Siie3 Image size KB 64ym 325 458 eoe 695 Storage environment Imaging plates must be stored in their protective box below 33 C The box must be kept closed to remain dust free Cleaning Use lint free cotton or a lens cleaner to wipe the imaging plates Use a lint free cloth dampened with ethanol anhydride to remove stains that do not come off easily Do not use any other cleaning solvents Material Europium activated barium fluorohalide Disposal Imaging plates are problem waste Return them to the manufacturer for disposal Never use damaged imaging plates Material Polyethylene _ _ _ _ _ S e 40 User s manual 8201052 8 Technical Specifications Digora Optime 8 3 Computer specification
9. Remove the sealed protective bag from the pa tient s mouth NOTE If a risk of cross contamination exists wash disinfect and dry the protective bag before open ing it Click the GREEN multi connect icon which is in the System Tray in the bottom right hand corner of the PC display to reserve the unit The Optime Multi Connect window will appear Click the Reserve the Scanner button in the Optime Multi Connect window to reserve scan ner The window will disappear and the GREEN multi connect icon will start to flash This indicates that you have now reserved the scanner Note that when the scanner is in the reserved mode the GREEN light on the unit will stop flash ing and stay on and the scanner door will open NOTE If the multi connect icon is YELLOW it indicates that the unit has been reserved by someone else Wait until the unit is free NOTE If the multi connect icon is GRAY it indicates that the unit has not been switched on or is just starting up and is not ready for use Switch the unit on and or wait until the unit is ready for use 25 Digora Optime 3 Multi Connect Version ge 4 Open the sealed protective bag Flap 5 Slide the plate cover and imaging plate out of the protective bag Keep the imaging plate in the plate cover so that you do not touch the imaging plate or allow it to be exposed to bright light Protective bag Plate cover and imaging plate ha gt 6 Slide the imaging pla
10. Removing imaging plates from the plate collector Slide the plate collector out of the unit and tip the imaging plates out onto aflat surface If they are not to be used again store them in the optional storage box Shutting down the unit 1 Press and hold down the stand by key until the stand by light comes on NOTE If the unit remains in the energy save mode for several hours door closed and green light flash ing it will automatically shut down NOTE If there is an untransferred image in the unit the unit will not automatically shut down 16 User s manual 8201052 2 Standard Version Digora Optime Erasing an Imaging Plate 1 Pressthe Stand by key to switch the unit on After 60 seconds the plate carrier will slide out of the unit Plate carrier AA 2 Press and hold down the Start key the GREEN light will flash until the YELLOW light comes on When both lights are on the unit is in the Erase mode 3 Slide the imaging plate into the plate carrier as far as it will go The back of the imaging plate the black side must face the plate carrier A magnet will hold the imaging plate in position Q Image plate WRONG User s manual 8201052 17 Digora Optime 18 2 Standard Version Release the imaging plate and the plate carrier will slide into the unit and the unit door will close The YELLOW light will
11. User s Manual for the Digora Optime Standard version and the Digora Optime Multiconnect version CE 0537 This unit is marked according to the Medical Device Directive 93 42 EEC if the unit contains the CE mark User s Manual for the Optime Document number 8201052 rev 2 0509 Original approved English language version Manufactured by SOREDEX P O BOX 148 FIN 04301 TUUSULA FINLAND Tel 358 10 394 820 Fax 358 9 701 5261 Digora Optime Soredex endeavours to produce product documentation that is accurate and up to date However our policy of continual product development may result in changes to products that are not reflected in the product documentation There fore this document should not be regarded as an infallible guide to current product specifications Soredex maintains the right to make changes and alterations without prior notice II User s manual 8201052 Digora Optime Contents aro HOI eor N 1 AD WS UI ste aa an na Mn naa Na 1 1 2Warnings and precautions sea kB na 2 1 3 Handling Imaging Plates asss ebay 3 1 4 Positioning the unit ooooo Woman 3 2 Optime Standard Version JJ 4 2 1 Main parts and Conor AA 4 2 2 Indicator NG MS bai on osn am amen mma Mma ana 5 2 3 Using the Unit ena Men alinea laen bo a aaa aaea T Preparing the image read out SyStem ooooo oom 7 Preparing the imaging plate caooooooooWooooooommewonem makan asa 8 Taking an exposure using the
12. as far as it will go Make sure that the black side of the imaging plate the back is against the tape black side of the protective bag SIZE 1 2 3 CORRECT WRONG WRONG A Protective Tape Imaging plate bag in cover CORRECT SES User s manual 8201052 23 WRONG WRONG Nahan Xx PE a Digora Optime 3 Multi Connect Version 4 Remove the cover paper from the sealing tape Fold the flap over onto the sealing tape A score line on the front of the bag will help you to fold the flap PA Smooth the flap from the centre out to ensure that the seal does not wrinkle Cover paper Sealing tape Flap Taking an exposure using the imaging plate 1 Place the sealed protective bag in the patient s mouth in the required position for the image you wish to take The back of the protective bag the black side must face away from the X ray source P lA x Tp T TX a A X ray source 1S SO X ray source we L Mena Man Protective bag with imaging plate N 2 Select an exposure value appropriate for the exposure you are taking The unit can read im ages taken with exposure times from 0 05 to 0 63 seconds at 7 mA 3 Protect yourself from radiation and take the expo sure 24 User s manual 8201052 3 Multi Connect Version Digora Optime Reading the imaging plate GREEN On GREEN Flashing YELLOW Ol GRAY Ol User s manual 8201052 1
13. collector out of the unit and tip the imaging plates out onto a flat surface If they are not to be used again store them in the optional storage box 30 User s manual 8201052 3 Multi Connect Version Digora Optime Shutting down the unit 1 Press and hold down the stand by key until the stand by light comes on NOTE If there is an untransferred image in the unit the unit will not automatically shut down Erasing an Imaging Plate 1 From the PC click the GREEN multi connect icon in the bottom right hand corner of the PC display to reserve the unit The Optime Multi Connect window will appear 2 Click the Reserve Scanner button to reserve scanner The window will disappear and the GREEN mutti connect icon will start to flash This indicates that you have now reserved the scanner GREEN Flashing TEJ User s manual 8201052 31 Digora Optime 3 Multi Connect Version 3 Press and hold down the Start key the GREEN light will flash until the YELLOW light comes on When both lights are on the unit is in the Erase mode 4 Slide the imaging plate into the plate carrier as far as it will go The back of the imaging plate the black side must face the plate carrier A magnet will hold the imaging plate in position fi Q Image plate WRONG Release the imaging plate and the plate carrier will slide into the unit and the unit door will close The YELLOW ligh
14. mage read is not transferred to the PC because of a network PC or software failure the image can be retrieved IMPORTANT NOTE The LAST read image can only be retrieved if the unit has been left connected to the power supply If the unit has been disconnected the image will be lost YELLOW f User s manual 8201052 To retrieve the last image 1 2 Correct the problem that caused the network failure and then reopen the new or existing pa tient card The multi connect icon will be YELLOW and the tool tip will say Image pending which means that there is an untransferred image in the unit Click the Icon and the Optime Multi Connect window will appear Click the Read Pending Image button to retrieve the last read image The last read image will appear on the patient card 29 Digora Optime 3 Multi Connect Version NOTE Check the name associated with the pending image The unit will remain reserved for the op erator who scanned but was unable to transfer the pending image Image quality warning message The following WARNING message may appear on the PC display during or after read out Degraded image quality PROBLEM Some of the read out lines on the image are not within the factory set quality limits SOLUTION If the image looks okay no action is necessary If the message appears frequently contact your dealer for assistance Removing imaging plates from the plate collector Slide the plate
15. n 2 1 Main parts and controls PC with dental imaging software e g Digora for Windows 2 5 or above Single or network connection via Ethernet RJ 45 cable Unit door Plate collector Stand by key Start key Indicator lights Red Error j T Yellow Warning Green Ready Read out Stand by light Energy Save View of rear Power connector PC connector Hub connector 4 User s manual 8201052 2 Standard Version Digora Optime 2 2 Indicator lights W e e IN o R H e g e IN 2 2 User s manual 8201052 The different statuses of the indicator lights are de scribed below Stand by light on Unit is shut down OFF Press stand by key to switch unit on GREEN on Unit ready to read an imaging plate Insert imaging plate GREEN slow flashing Unit in the energy save mode Press the Start key to enter ready mode GREEN fast flashing Unit is reading erasing an imaging plate YELLOW on DfW not opened or untransferred image in unit Open DfW and the image will automatically appear YELLOW slow flashing There is no Ethernet link YELLOW fast flashing Unit carrying out its selftest Digora Optime 2 Standard Version GREEN on YELLOW on Unit is in the Erase mode e M GREEN flashing YELLOW on Unit is in the Erase mode and is erasing an imaging plate C 9 are i GREEN on YELLOW fla
16. osed from the wrong side The image must be mirrored using dental imaging software IMPORTANT NOTE RETRIEVING IMAGES If an image is not transferred to the PC because of a network PC or software failure the image can be retrieved For information on how to do this see section Retrieve last image User s manual 8201052 2 Standard Version Digora Optime 6 After the imaging plate has been read it will be erased and then automatically ejected from the unit into the plate collector After the imaging plate has been ejected the GREEN light will remain on and the unit door will stay open The unit is now ready to read the next imaging plate If no new imaging plate is inserted into the unit within a certain time period the unit door will close and the unit will enter the energy save mode Five seconds before the unit enters the energy save mode the YELLOW warning light will start to flash and the unit will start to beep eee Le After five seconds the plate carrier will slide back inside the unit the door will close the YELLOW light will go out and the GREEN light will start to flash The unit is now in the energy save mode If the Start button is pressed while the YELLOW warning light is flashing the unit will not enter the energy save mode User s manual 8201052 13 Digora Optime 2 Standard Version To exit the energy save mode press the Start button The plate carrier
17. ow allow the image to be manipulated 2 Click OK to save the tooth numbers with the image 34 User s manual 8201052 4 Setup options 4 2 Resolution 1 Digora Optime Inthe Image Scanning section select either Super or High Super gives a pixel size of 40u High a pixel size of 64u Super will give you better resolution images but you will use more memory space as the image files are larger Click OK to close the window and select the resolution 4 3 Image Processing User s manual 8201052 1 In the Image processing click the Noise Filter ing check box Noise filtering is normally always selected It make images smoother when they are taken at lower doses Click OK to close the window and select the noise filtering 35 Digora Optime 5 Cleaning and disinfecting the unit 5 Cleaning and disinfecting the unit WARNING Switch off and disconnect the unit before cleaning or disinfecting it Do not allow any liguid to enter the unit 5 1 Cleaning the unit Use anon abrasive cloth moistened with either Cool or lukewarm water or soapy water or mild detergent or butylalcohol or ethanol ethyl alcohol 96 to clean the unit After cleaning wipe the unit with a non abrasive cloth moistened with plain water Never use solvents or abrasive cleaners to clean the unit Never use unfamiliar or untested cleaning agents If you are not sure what the cleaning agent contains DO NOT
18. ronic components 37 Digora Optime 7 Symbols that appear on the unit 7 Symbols that appear on the unit DANGEROUS VOLTAGE LASER RADIATION IMPORTANT INFORMATION Refer to user s manual BBB Direct current Connector for single user interface cable RJ45 straight cable transmit receive swapped at PTC connector Connector for multiuser interface cable RJ45 straight cable fe iO CE 0537 Symbol MDD 93 42 EEC This unit is marked according to the Medical Device Directive 93 42 EEC if the unit contains the CE 0537 aes Standby Start UL Classification symbol KIA MEDICAL EQUIPMENT WITH RESPECT TO ELEC y II 4 TRIC SHOCK FIRE AND MECHANICAL HAZARDS eL Jus ONLY IN ACCORDANCE WITH UL 60601 1 CAN CSA C22 2 NO 601 1 5D42 if the unit contains the UL symbol This symbol indicates that the waste of electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately Please contact an authorized representative of the manufacturer for information concerning the decommissioning of your equipment 38 User s manual 8201052 8 Technical Specifications Digora Optime 8 Technical Specifications 8 1 OpTime Unit Digital Optime Unit DXR 50 Classification Class 1 eguipment No applied part IEC60601 1 Continuous operation IPXO enclosed eguipment without protection against ingress of liguids Laser Safety Classification CLASS 1 LASER PRODUCT EN 60825 1 A1 20
19. s Single User PC NetworkPC Network server PC Operating Windows 98SE ME Windows 98SE ME Windows NT 4 0 system NT 4 0 SP6a 2000 NT 4 0 SP6a 2000 Server 2000 Server SP2 XP SP1 SP2 XP SP1 PC Pentium III CPU or Pentium III CPU or Pentium III CPU or better CD ROM CD better CD ROM CD better CD ROM RW drive RW drive recommended recommended RAM Harddisk 20 GBor more 20GBormore 20GBormore Monitor 17 XGA 1024x768 117 XGA 1024x768 No requirement minimum True Color 75 Hz or True Color 75 Hz or recommended 19 UXGA 19 UXGA 1280x1024 True 1280x1024 True Color 85 Hz Color 85 Hz adapter or more or more Network 100 Ethernet 100 Ethernet 10 100 Ethernet Adapter Card NOTE 10 Mbit s only NOTE 10 Mbit s only is not compatible is not compatible Network TCP IP TCP IP NetBEUI Windows NT 2000 protocols Server TCP IP NetBEUI Novell NetWare IPX SPX Back up Tape drive SCSI or See server Tape drive SCSI or other back up device requirements other back up device One workstation UPS Uninterruptible should have CD RW Power Supply drive for archive purposes User s manual 8201052 41 Digora Optime 8 Technical Specifications 8 4 Main dimensions 394mm 15 5in 343mm 13 5in 221mm 8 7in 191mm 7 5in 42 User s manual 8201052
20. shing Unit is entering the energy save mode G o Rae RED flashing ERROR Switch the unit off and then on again If the red light comes on again contact your dealer for help LN e User s manual 8201052 O 2 Standard Version 2 3 Using the unit Digora Optime Preparing the image read out system 1 Switch on the computer that is connected to the unit Open Digora for Windows or the dental imaging software you are using If you are using the unit for the first time you may wish to check and or change the setup options See section 4 Setup options for more informa tion Open the patient card where you wish to place the new image or open anew patient card Press the Stand by key to switch the unit on The YELLOW stand by light will turn off and unit will carry out a selftest during which the YELLOW warning light will flash The selftest will last about 30 seconds When the plate carrier slides out of the unit door and the GREEN light comes on the unit is ready to use User s manual 8201052 Plate carrier err NOTE If the GREEN light does not come on it indicates that the unit is not connected to the PC If the RED light comes on contact your dealer for advice Digora Optime 2 Standard Version Preparing the imaging plate IMPORTANT NOTE If the imaging plate is being used for the very first time or if it has not been used within the last five days it
21. st be in compliance with the related nationally harmonized IEC standards Equipment not suitable for use in the presence of flammable anaesthetic mixture with air or with oxygen or nitrous oxide Only use the SKYNET SNP PA59 M power supply unit that is supplied with the unit Do not use any other power supply units with the unit If this device will be used with 3rd party imaging application software not supplied by SOREDEX the 3rd party imaging application software must comply with all local laws on patient information software This includes for example the Medical Device Directive 93 42 EEC and or FDA if applicable User s manual 8201052 Introduction Digora Optime 1 3 Handling Imaging Plates After exposing an imaging plate and removing the imaging plate and cover from its protective bag do NOT expose the imaging plate and cover to very bright light before reading the imaging plate Also read the imaging plate as guickly as possible after it has been exposed Do not leave read or unread imaging plates in their protective bags for long periods of time Always handle the imaging plates with care and avoid situations that could scratch them When imaging plates are not being used store them in their protective box below 33 C 1 4 Positioning the unit User s manual 8201052 Do NOT position the unit so that the door is in or near very bright light Digora Optime 2 Standard Version 2 Optime Standard versio
22. stay on and the GREEN light will start to flash which indicates that the imaging plate is being erased aaa T After the imaging plate has been erased it will be automatically ejected from the unit into the plate collector The imaging plate can now be used to take an exposure To exit the Erasing mode either wait 15 seconds for the unit to automatically exit the mode or press and hold down the Start key until the YELLOW light goes out User s manual 8201052 3 Multi Connect Version Digora Optime 3 Optime Multi Connect version 3 1 Main parts and controls kasi PCs with dental imaging software Single or Network connection via Ethernet RJ 45 cable Plate collector ala key a key Indicator lights Red Error Yellow Warning Green Waiting Ready Read out Stand by light View of rear Power connector PC connector Hub connector User s manual 8201052 19 Digora Optime 3 Multi Connect Version 3 2 Indicator lights o Qee ny 9 one No 0 The different statuses of the indicator lights are de scribed below Stand by light on Unit is shut down OFF Press stand by key to switch unit on GREEN on Unit is reserved and ready to read an imaging plate Insert imaging plate GREEN slow flashing Unit in the waiting mode Click the Multi connect icon to reserve the unit GREEN
23. t will stay on and the GREEN light will start to flash which indicates that the imaging plate is being erased r T 32 User s manual 8201052 3 Multi Connect Version Digora Optime 5 After the imaging plate has been erased it will be automatically ejected from the unit into the plate collector The imaging plate can now be used to take an exposure 6 To exit the Erasing mode either wait 15 seconds for the unit to automatically exit the mode or press and hold down the Start key until the YELLOW light goes out User s manual 8201052 33 Digora Optime 4 Setup options 4 Setup options The unit has several setup options that allow you to set the image quality to your requirements To select the setup options 1 From the dental imaging software you are using select Digora Optime Setup gt Scanner page 4 1 Tooth numbering Numbers can be assigned to the teeth that appear on the image Selecting the tooth numbering feature 1 Inthe Image Scanning section click the Show Image Preview and Dental Chart check box 2 Click OK to close the window and activate tooth numbering Using the tooth numbering feature After an image plate has been read a window will open that shows the image and a tooth location map 1 Click the tooth teeth on the map that correspond to the tooth teeth in the image Tooth numbers will be assigned to the selected teeth Tools at the top of the wind
24. te and plate cover into the plate carrier as far as they will go The back of the imaging plate the black side must face the plate carrier A magnet will hold the imaging plate in position Q Imaging plate and plate cover WRONG Slide the plate cover off of the imaging plate leaving the imaging plate in position Plate cover A WRONG Imaging plate 26 User s manual 8201052 3 Multi Connect Version User s manual 8201052 Digora Optime IMPORTANT NOTE If the YELLOW light starts to flash and the unit starts to beep as you are inserting the imaging plate it indicates that the reserved time has elapsed and the unit is exiting the reserved mode DO NOT continue to insert the imaging plate Reserve the unit again and then re insert the imaging plate After the cover has been removed the plate car rier with imaging plate will automatically slide into the unit and the unit door will close The GREEN light will start to flash which indicates that the imaging plate is being read CAUTION If the plate carrier does not slide into the unit after the plate cover has been removed the imaging plate is misaligned or has been placed in the unit the wrong way round Re insert the imaging plate correctly A read out progress window will appear on the PC display After a few seconds the new image will appear on the patient card NOTE There is a metal disk on
25. than those specified herein may result in hazardous laser radiation exposure When handling imaging plates plate covers and protective bags always take the appropriate hygiene measures and precautions to prevent cross contamination The imaging plates are harmful if swallowed Do not move or knock the unit when it is reading an imaging plate The use of control or adjustment or performance of procedures other than those specified herein may result in hazardous laser radiation exposure This unit must only be used to read SOREDEX OPTIME image plates and must not be used for any other purpose NEVER use imaging plates or protective covers from other manufacturers This unit or its accessories must not be modified altered or remanufactured in any way Only the manufacturer s authorized service personnel are authorized to carry out maintenance and repair There are no user serviceable parts inside the unit Infection control procedures must be observed when using accessories such as film holders x ray tube guides and imaging plates When using accessories always follow the manufacturer s instructions on how to use the accessory and prevent cross contamination from one patient to another This device can interfere with other devices due to its EMC characteristics Other devices can interfere with this device due to their EMC characteristics This device complies with IEC 60601 1 standard Accessory equipment connected to this device mu
26. use it If you use a Spray cleaning agent DO NOT spray it directly at the open or closed unit door 5 2 Disinfecting unit CAUTION Wear gloves and other protective clothing when disin fecting the unit Wipe the unit with a cloth dampened with a suitable disinfectant solution such as ethanol 96 Never use abrasive corrosive or solvent disinfectants All sur faces must be dried before the unit is used WARNING Do not use any disinfecting sprays as the vapor could ignite causing injury Disinfecting techniques for both the unit and the room where the unit is used must comply with all local and national regulations and laws concerning such equip ment and its location 36 User s manual 8201052 6 Maintenance repair and disposal Digora Optime 6 Maintenance repair and disposal 6 1 Maintenance 6 2 Repair 6 3 Disposal User s manual 8201052 The unit does not reguire any regular maintenance If the unit is damaged or malfunctions in any way repairs must only by carried out by a service repre sentative authorized by the manufacturer At the end of the useful working life of the unit and or its accessories make sure that you follow national and local regulations regarding the disposal of the unit its accessories parts and materials The unit includes some or all of the following parts that are made of or include materials that are non environmentally friendly or hazardous electronic circuit boards elect
27. will slide out and the GREEN light will stop flashing and stay on The unit is now in the ready mode Retrieve last image If the last image read is not transferred to the PC because of a network PC or software failure the image can be retrieved IMPORTANT NOTE The LAST read image can only be retrieved if the unit has been left connected to the power supply If the unit has been disconnected the image will be lost To retrieve the last image 1 14 Correct the problem that caused the network failure and then reopen the new or existing pa tient card The last scanned image should automatically be transferred If it is not from the dental imaging software your are using select Digora Optime Setup gt Scan ner page In the Retrieve Last Image field click the check box to retrieve the last read image Click OK to close the Digora Optime Setup window will close The last read image will appear on the patient card User s manual 8201052 2 Standard Version Digora Optime Image guality warning message User s manual 8201052 The following WARNING message may appear on the PC display during or after read out Degraded image guality PROBLEM Some of the read out lines on the image are not within the factory set guality limits SOLUTION If the image looks okay no action is necessary If the message appears frequently contact your dealer for assistance 15 Digora Optime 2 Standard Version
28. y out a selftest during which the YELLOW warning light will flash and the unit door will open The selftest will last about 30 seconds When the unit door closes and the GREEN light starts to flash the unit is in the wait mode and is ready to be reserved 22 NOTE If the GREEN light does not come on it indicates that the unit is not connected to the PCs If the RED light comes on contact your dealer for advice User s manual 8201052 3 Multi Connect Version Digora Optime Preparing the imaging plate IMPORTANT NOTE If the imaging plate is being used for the very first time or if it has not been used within the last five days it MUST be erased See section 3 Erasing an imaging plate for information on how to do this CAUTION When handling imaging plates plate covers and protective bags always take the appropriate hygiene measures and precautions to prevent cross contami nation Metal disk 1 Place the imaging plate you plan to use onto the long half of the plate cover The blue active side of the imaging plate must face the plate cover and the metal disk on the back of the imaging plate Long 1 7 Short must be positioned near the outer edge of the half half plate cover Imaging plate Plate cover Short half 47 gt 2 Foldthe short half of the plate cover over onto the E imaging plate Metal disk MED 3 2 7 1 7 3 Slide the plate cover and imaging plate into the protective bag
Download Pdf Manuals
Related Search