IMAGE JY-130B & JY-90B USER MANUAL
Contents
1. P N Switch the image mode between positive and negative 8 LAMP Lamp control switch the lighting mode as up lamp down lamp all turned off up lamp etc 9 AF Auto focus button 0 ZOOM ZOOM Image zoom in and zoom out control 1 FOCUS FOCUS Adjust focus manually 2 FRZ Image control switch between shoot and freeze 3 FN Function button using with other buttons for special functions Control with FN button 1 FN LAMP Switch the image between text mode and dynamic mode Text mode gives sharper and better colored images when showing printed material 2 FN BRT FN BRT Image chroma control red 3 FN SHARPNESS FN SHARPNESS Image chroma control blue 4 FN ZOOM FN ZOOM MIC volume control 5 FN PC Capture the image in the screen Available for models with image capture function 6 FN AV Multi image mode enabled Available for models with image capture function Press again to return to normal mode In multi image mode ZOOM Display the first image FOCUS Display the second image ZOOM Display the third image FOCUS Display the fourth image FN AF Images page turning 7 FN FOCUS Output right and left mirror image 8 FN FOCUS Enable the function of side by side images comparison on same screen 3 SPECIFICATIONS Maximum power consumption 20 W Operating condition Dimensions packing case 465mmx430m2. 8 6866 Fax 02 9938 6899 Address Unit H 134 140 Old Pittwater Rd BROOK VALE NSW 2100 Email info abimage com au Website www abimage com au LN PART NAME AND FUNCTIONS 1 camera control knob 2 sensor cover 3 upper mechanical arm 4 main mechanical arm 5 side lamp 6 lighting arm 7 power switch 8 base light 9 control panel 10 base unit 11 infrared receiver 2 Rear Panel Sooo O9 9 0 n a A DUT mc eg VGA DUTZ R S VIDEO VGA OUTI VI Ll RI Video amp Audio Input V2 L2 R2 Video amp Audio Input VIDEO Composite Video Signal Output S VIDEO S video Output YC synchronization sever MIC Microphone Input Al A2 PC Audio Input A OUT Audio Output VGA OUTI VGA OUT2 VGA Output VGAI VGA2 VGA Input RS 232 Serial Port for Control System USB PC Signal Transmission optional 3 Front Control Panel LAMP SHARPNESS SHARPNESS J o BLUE BLUE m H AV PC 1 HOME When the camera is in operating press this button for 3 seconds it will stop transmitting image BRT RED and go to standby if press for another 3 seconds the camera will get back to work again 2 AV Switch the input signal source videol or video2 3 PC Switch between PC1 amp PC2 4 AC Perform white balance automatically 53 BRT BRT Image brightness control 6 SHARPNESS SHARPNESS Image sharpness control 7
3. abi A Brighter Image PI IMAGE Document Camera JY 130B 1 3 Megapixel Camera output resolution amp JY 90B 850 000 pixel Camera output resolution USER MANUAL ead this manual carefully before operating the visual presenter and keep it for reference OTICES PLEASE READ CAREFULLY BEFORE USE Use the document camera under the rated electric conditions Do not place the document camera on any unstable surface It may fall and cause injures or damages Do not place this device directly under sunlight or near heaters Do not place this device near water Keep the camera away from acid or alkali gas Do not place this document camera in humid dusty windy or vibrant locations The recommended operating environment is Temperature O C 45 C 32 F 113 F Humidity less than 75 Always unplug BEFORE cleaning the device Use a damp soft cloth for cleaning Do not use volatile solvent When this equipment functions abnormally such as smoke smell noise immediately unplug and call for professional assistance Unplug the document camera or shut off the power when not in use CONTENTS PART NAME AND FUNCTIONS1 e uses se ee LL eiii iLnuu 3 FA ne EE 3 GEN sg iu EE 4 ST ront COBLGO Palade ly ebe 5 SPECIEI DO N use GO TA a AYN ANFON SANG DID CY TF SYR 6 SEO UP DR DF E eeu dyes aden eset AN ED Wi OPERATION PROCEDURE e EE 8 TROUBLE SHOGTIN Le 9 SERVICE Contact A Brighter Image Pty Ltd Tel 02 993
4. lor choose the Text mode by pressing FN and P N button 3 Showing the 3D objects Use the FOCUS FOCUS buttons on the front panel to adjust the focus on any part of the 3D object 4 Showing the transparent material such as an overhead transparent sheet Press the Lamp button until the built in base light lights up TROUBLE SHOOTING No image Power cord is not properly connected Cables are not properly connected Power switch is not turned on The built in fuse is broken Change fuse Upper light not on The filament is broken Change the bulb the lamp is not fully plugged in its holder Out of focus or blurring The object is too close to the lens image Focus is on the max point of Tele press Wide Auto focus 1s not on press AF again Fog on the lens in damp climate It will disappear gradually when the equipment warms up If the problem still remains after checking the above consult your dealer or authorized service personnel PACKING LIST AND ACCESSORIES VGA Cable USB Software CD I installed in the power receptacle
5. mx220mm WxDxH Light source Output Camera 48 KHz horizontal 60 Hz vertical SETTING UP 1 Unpack put aside all packing materials Unfold the lighting arms until reach the end position 2 Raise the camera arm completely 3 Rotate the camera head until the lens face the center of the base unit 4 Connect RGB interface use the provided RGB cable connect the output of the document camera with the RGB input the display monitor television or projector 5 Connect the composite video in interface use the provided RCA pin cable 6 Connect the S video in interface connect the S video out interface mini DIN 4P with the S video in interface of the display 7 Plug the power cord into the power cord receptacle of the document camera and the AC outlet OPERATION PROCEDURES 1 General 1 Turn on the Power switch 2 Place the target object on the base unit surface 3 Adjust the image size according to the object size by pressing the ZOOM ZOOM buttons on the control panel 4 Press the AF button for automatic focus 5 Frz button can be used to lock the image while changing displaying materials FN and FRZ button can be used to compare a previous captured image with the current image side by side Turn the knob on the camera head will changing the alignment of the showing image 2 Showing printed material For sharper image and more vivid co
Download Pdf Manuals
Related Search