GDO-9v3 User Manual.indd
Contents
1. Step 23 2 Testing Battery Back Up a Press either the OPERATE button or transmitter to test the opener b Whilst door is in motion disconnect mains power the door should continue to operate as normal NOTE Wait for the door to complete its travel c Press the OPERATE button or transmitter to activate the door d Whilst door is in motion re connect power The door should complete the cycle as normal Step 23 3 Troubleshooting If door stops or moves very slowly under battery power the batteries may be weak or have no charge Connect mains power and allow the batteries to charge This may take 24 48 hours to reach maximum charge capacity Owner Installation Instructions GDO 9v3 SecuraLift O 27 28 Final Set Up O ci MARGIN Q E E TIME OPEN FORCE LO O G amp LIMIT SET US CLOSE e rose CODE Tu LIMIT GDO 9v3 SecuraLift Owner Installation Instructions Step 24 Setting of Courtesy Light Time The preset courtesy light time is three minutes This time can only be changed by PG3 programmer Step 25 Setting the Pet Mode position The default Pet Mode height can be changed as follows a Make sure the door is closed then press and hold the OPEN button for six 6 seconds Fig 52 until you hear three beeps and the OPEN and CLOSE LEDs flash rapidly b Press the OPEN button to move the d2. Sectional door with track For a one piece door on tracks Fig 14 proceed with the installation from Step 4 Door _____y N Highest point of travel One piece door with track For a one piece door without tracks on springs Fig 15 proceed with the installation from Step 8 One piece door without track GDO 9v3 SecuraLift Owner Installation Instructions O 14 Mounting on a Track Type Door A WARNING The opener must be securely fastened to structural supports otherwise opener failure may ensue causing serious personal injury and or property damage Step 4 Determine Bracket Position a b Open the door and find the highest point of travel of the top door panel Using a level transfer this height to the wall above the door Fig 16 and mark a line 60mm above it Determine the centre point on the wall above and on top of the door Draw two lines extending 21 5mm from each side of the centre point Fig 17 Step 5 Mounting the Wall Bracket a A Centre the bracket over the intersection of these two lines Mark centres for at least two holes Fig 17 e Ensure this is into a solid mounting point Drill holes into the wall with an appropriate bit Secure to the wall using IF CONCRETE OR BRICK 8mm 5 6 loxins dynabolts IF TIMBER wood screw 20 or similar min 50mm WARNING Make sure concrete brick wall or timber lintels are sol
3. Beam In most countries P E Beams are mandatory on all garage doors fitted with automatic openers For a small additional outlay Automatic Technology recommends that Photo Electric Beams be installed with the automatic opener ensuring additional safety and peace of mind DO NOT operate the opener unless the garage door is in full view and free from objects such as cars and children people Make sure that the door has finished moving before entering or leaving the garage DO NOT operate the opener when children persons are near the door Children must be supervised at all times when the SecuraLift is in use Serious personal injury and or property damage can result from failure to follow this warning DO NOT allow children to operate the SecuraLift Serious personal injury and or property damage can result from failure to follow this warning Regularly check to make sure that the safety obstruction force is working correctly and is tested and set as per page 20 of this manual Failure to follow these instructions could result in serious personal injury and or property damage This test must be repeated at regular intervals and the necessary adjustments made as required Photo electric beams must be installed if the closing force at the bottom edge of the door exceeds 400N 40kgf DO NOT disengage the door opener to manual operation with children persons or any other objects including motor vehicles within the doorway The door open
4. O GDO 9v3 SecuraLift Featuring TrioCode Technology autQmatic TECHNOLOGY smart simple secure INSTALLATION INSTRUCTIONS OWNERS COPY WARNING It is vital for the safety of persons to follow all instructions Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and or property damage Please save these instructions for future reference Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener Automatic Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury damage cost expense or claim whatsoever suffered by any person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener in accordance with these installation instructions O GDO 9v3 SecuraLift Owner Installation Instructions O GDO 9v3 SecuraLift Overhead Garage Door Opener Important Safety Instructions Features Operating Controls Kit Contents Installation Knockdown C Rail Assembly C Rail Attachment Determine Door Type Mounting Track Type Door Mounting Spring Loaded Door Mounting Door Bracket amp Arms Programm
5. code grabbing a thing of the past These transmitters also overcome interference issues by simultaneously sending a signal over three different frequencies Even if two of the three signals are jammed the system will still work ALPS Automatic Limits Positioning System ALPS does away with manual adjustment of the door s limits position using mechanical parts such as cams and microswitches During installation the hand held transmitter can be programmed to set the door limits positions ISS intelligent safety obstruction system While the door is performing a close cycle should it hit an obstacle or be restricted in some manner it will automatically reverse The amount of force the door should encounter before reversing is automatically adjusted by the doors control system during the initial installation of the automatic door opener The door will also stop if restricted whilst opening The Safety Obstruction Force should be checked monthly Auto courtesy light The courtesy light comes on automatically for three minutes whenever the door is activated The light can also be operated independently of the door by coding a dedicated button on a transmitter O GDO 9v3 SecuraLift Owner Installation Instructions O SmartSolar and Battery Back Up Compatibility optional The opener can be fitted with a SmartSolar or Battery Back Up kit for operation in the event of a power outage or where mains power access is not availa
6. Remotely Coding Transmitters Using this method transmitters can be coded without access to the opener s control panel as long as a pre coded transmitter is available A IMPORTANT NOTE The door or courtesy light must activate when the steps below are performed This indicates that the pre coded transmitter is in range of the opener and the correct button has been pressed Take any pre coded transmitter Press the button for the function to be duplicated and release Using a small needle press and hold firmly for two seconds through the Coding Hole Fig 43 WITHIN 10 SECONDS take the additional transmitter you wish to code Decide which button that you want to activate the function to be duplicated e g activate the door or turn on the courtesy light Hold the new transmitter s button for two seconds pause for two seconds hold again for two seconds and then release Wait for 10 seconds and then press the new Oss i transmitter s button to test b C C O J ar VMe Step 19 1 Deleting a Stored Transmitter a a Code a Select the transmitter you want to delete b Press and hold the DOOR CODE BUTTON Fig 44 c Press the transmitter button you would like to delete for two seconds pause for two seconds press again for two seconds and then release d Release the DOOR CODE BUTTON The code should now be deleted Confirm this by pressing the transmitter button the function e g door opening should not r
7. Instructions WARNING The opener must be securely fastened to structural supports otherwise opener failure may ensue causing serious personal injury and or property damage Step 8 Determine the Door s Centre a Find the centre of the door and mark this location both above the door and on top of the door b Draw two lines 21 5mm either side of this Fig 20 Step 9 Prepositioning the Opener a Raise the door to open position b Rest the opener on the top edge of the door with end of the rail against the wall Fig 21 c Support the powerhead level with the lowest point of the open door Fig 21 NOTE Do not slide rail along the face of the door Step 10 Mounting the C Rail a Close the door slowly The rail will be elevated by the top edge of the door as it moves b Stop the door when it is at its highest point of travel Allow 25mm additional height for clearance between the door and the track Fig 22 c Support the Rail in this position and close the door d The height determined in Step 10 b will be the height at which to mount the wall bracket e Centre the bracket along the line determined in Step 8 f Using the bracket as a template mark a minimum of two holes and drill with appropriate size bit For a more secure fitting the wall bracket can be anchored using more than two holes g Secure the bracket to the wall using IF CONCRETE OR BRICK 8mm 5 6 loxins dynabolts IF TIMBER wood
8. JZ Q ws KIOFI E ne CODI E Queer sie I A E S JA cLose O GDO 9v3 SecuraLift Owner Installation Instructions 22 O ng Transmitters Step 18 1 Code a Transmitter Button for Door Operation a Press and hold the DOOR CODE button Fig 38 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release the DOOR CODE BUTTON d Press the transmitter button to test Step 18 2 Code a Transmitter Button to Enable Vacation mode The opener can be programmed into a Vacation Mode where the opener will not respond to any transmitter except the button of the transmitter the one programmed for vacation mode a Briefly press the DOOR CODE button once then press it again and hold will beep two times on second press Fig 39 b Press one of the four 4 buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release DOOR CODE button d Press and hold the transmitter button for six 6 seconds to set Vacation Mode The door code led will stay lit while vacation mode is active e To reset Vacation Mode press the same button for two seconds Step 18 3 Code a Transmitter Button to Enable AUX OUTPUT a Briefly press the DOOR CODE button two 2 times then press it again and hold will beep three times
9. Limit Positions Limit positions can be deleted by the following steps a Follow Steps 14 2 a and b as outlined previously b Repeat Steps 15 1 and 15 3 to set new travel limit positions There is no need to re code the transmitter Step 15 1 upon resetting travel limits The transmitter will still be stored in memory OPEN O korc LIMIT sET CLOSE TAN LIMIT am Button 1 Button 2 Inch Open Button 4 Inch Close Owner Installation Instructions GDO 9v3 SecuraLift O 19 Safety Obstruction Force Test AUTO CLOSE TIME 20 GDO 9v3 SecuraLift Owner Installation Instructions O A A WARNING Take care when testing or adjusting the Safety Obstruction Force Excessive force may cause SERIOUS PERSONAL INJURY and or PROPERTY DAMAGE WARNING Photo electric beams must be installed if the closing force at the bottom edge of the door exceeds 400N 40kgf Step 16 1 Testing Close Cycle Press the OPERATE button to open the door Fig 33 Place a piece of timber approximately 40mm high on the floor directly under the door Fig 34 Press the OPERATE button to close door The door should strike the object and start to re open Step 16 2 Testing Open Cycle a b C A Press the OPERATE button to close the door Fig 33 Press again to open the door When the door reaches the half open point grab the bottom rail of the doo
10. PE 2 2k2 0 25 WATT RESISTOR Y Receiver Transmitter CABLE 2 OPEN O LIMIT a O LIMIT Fores MARGIN SET THE Owner Installation Instructions GDO 9v3 SecuraLift O 25 SmartSolar Installation P1 Solar Shunt qaueg jos Wold laueg Jejog wo14 pay 26 O GDO 9v3 SecuraLift Owner Installation Instructions A WARNING Do not connect batteries until Step 22 3 Step 22 1 Mount the Charger Board Unplug the drive unit from mains power Remove the screws swing open the main cover Then remove the transformer EMC board if fitted and mains power cable Mount the pcb support with two screws Secure the Solar charger board on to the pcb support with 3 screws Fig 47 Plug the Charger Board s three wire harness red yellow black onto the control board s SBY 3 connector Fig 48 Plug the Charger Board s white one wire harness onto the control board s 24vac in connector Fig 48 Plug the black solar shunt onto both pins of the control board
11. door via the arms with the chain index by moving the door Ifthe trolley does not click firmly onto the chain index pull the cord backwards until it locks in place and try again b Press and hold Button 4 on the transmitter to close the door When the door is approx 20mm from the ground release Button 4 Fig 32 c Each press of Button 4 will allow you to inch the door closed Keep doing this until the door reaches the desired close limit position Ifthe door closes too far press Button 1 to inch the door towards open d When happy with the close limit position press Button 2 to store this in memory e Press and hold Button 1 to open the door When approx 20mm from the desired open position release Button 1 f Each press of Button 1 will allow you to inch the door open Keep doing this until the door reaches the desired open limit position Ifthe door is opened too far press Button 4 to inch the door towards closed IMPORTANT WARNING The door will AN automatically close open and close again once Step 15 2 f is performed Ensure that no persons or objects are in the door s path f When happy with the open limit position press Button 2 on the transmitter to store into memory g The door will now automatically close open and close to calculate the safety obstruction settings After this the opener can be operated with the OPERATE button Step 15 3 Resetting the Door
12. excludable conditions or warranties that are implied into this contract by relevant statute including the Trade Practices Act 1974 Cwth Subject to all of the matters set out below Automatic Technology Australia Pty Ltd ATA warrants a overhead door opener drive units for twenty four 24 months or 5000 cycles whichever occurs first and b all accessories for twelve 12 months from the date of purchase specified in the sales docket receipt as free of any defects in material and workmanship This warranty applies only where the purchaser a immediately notifies ATA or the retailer of the alleged defect b returns the product to the retailer and c presents the relevant sales docket and this warranty document to the retailer to confirm the date of purchase Except for this warranty ATA gives no warranties of any kind whatsoever whether express or implied in relation to the product and all warranties of whatsoever kind relating to the product are to the extent permissible by statute hereby excluded To the extent permissible by statute ATA disclaims any liability of whatsoever nature in respect of any claim or demand for loss or damage which arises out of a accidental damage to or normal wear and tear to the product or to the product s components b any cost relating to damage resulting from wear and tear c blown fuses loss or damage caused by electrical surges power surges or power spikes d loss or damage due t
13. for the start of the movement Owner Installation Instructions GDO 9v3 SecuraLift O 35 January 2008 Automatic Technology Australia Pty Ltd All rights reserved TrioCode and SecuraLift are trademarks of Automatic Technology Australia Pty Ltd No part of this document may be reproduced without prior permission In an ongoing commitment to product quality we reserve the right to change specification without notice E amp OE Automatic Technololgy Australia Pty Ltd ABN 11 007 125 368 autQmatic 6 8 Fiveways Boulevard TECHNOLOGY Keysborough Victoria 3173 Australia P 1300 133 944 61 2 9722 5666 International Enquiries Only E sales ata aust com au smart simple secure an alesco company www ata aust com au
14. screw 20 or similar min 50mm h Attach the bracket and C Rail with supplied pins Fig 18 WARNING Make sure concrete brick wall or timber lintels are solid and sound so as to form a secure mounting platform Step 11 Secure the Powerhead to the Ceiling a Secure the perforated angle not supplied to the ceiling above where powerhead s mounting holes will be See Fig 19 for a representative mounting b Connect the powerhead to the ceiling mounted perforated angle with M8x20mm screws and nuts Strips should not extend more than 18mm below centre of powerhead mounting holes Fig 19 Step 11 1 Alternative Mounting Option The opener can be fastened to the roof by driving a bolt through the C Rail into a structural timber support The bolt head s height must not exceed 6mm Fig 23 Step 12 Mounting Door Bracket The door bracket comes in two parts The bottom plate with two mounting holes is used on its own for one piece doors For sectional doors the top plate is placed over the bottom plate and is fixed with four 4 screws Fig 24 a Mount the door bracket or bracket assembly on the door s centre line one third down the top panel Fig 24 using M6 or equivalent screws not supplied b STEEL DOORS ONLY Bracket can be welded in place NOTE If in doubt about the door s strength AN reinforcement may be added to the door s frame where necessary Door damage may occur if the bracket is installed
15. the drive unit end only OR Multi Piece C Rail IMPORTANT NOTE If modification to the track length is required adjustment must be made only from drive unit end only 4 x C Rail Track 3 x C Rail Sleeve 1 x Shuttle Assembly 1x Tension Chain Assembly 1 x Track Accessory Pack 1 x Chain 10 O GDO 9v3 SecuraLift Owner Installation Instructions O Knockdown C Rail Assembly Step 1 Knockdown C Rail Assembly Note If your opener came with a one piece track proceed to Assembly step 2 page 13 dA a Place track pieces on flat surface for assembly All the track sections are interchangeable b Slide sleeve onto the track section Fig 05 Connect track by sliding sleeve onto next track section Tap fig 05 track assembly on piece of wood until track sections x are flush Repeat with remaining track sections s c Remove chain from package and lay chain out on Sora floor do not allow chain to twist d Loop the chain onto the pulley of tension chain assembly Slide the tension chain assembly with chain into the track Fig 06 e Slide shuttle assembly into opener end the track assembly be sure to insert shuttle assembly with hole side toward the door as shown with arrow in Fig 07 Push the sprocket support into opener end of the track f Feed the chain through the shuttle assembly then through the sprocket support and loop around the sprocket then feed back through the sprocket support and shuttl
16. using auto close mode a photo electric beam must be fitted correctly and tested for operation at regular intervals Extreme caution is recommended when using auto close mode All safety rules must be followed In order for the SecuraLift to sense an object obstructing the door way some force must be exerted on the object As a result the object door and or person may suffer damage or injury If the power supply cord is damaged it must be replaced by an Automatic Technology service agent or suitably qualified person Make sure that the door is fully open before driving in or out of the garage and fully closed before leaving the driveway Make sure that remote controls are kept out of reach of children Install the wall switch or wall mounted transmitter in a location where it is out of reach of children and the garage door is visible Owner Installation Instructions GDO 9v3 SecuraLift O Features Operation To open or close the door simply press a button on a TrioCode handheld transmitter a wall mounted transmitter or optional wall switch for two seconds During open and close cycles the door can be stopped by pressing the button again The next actuation will move the reverse the door s direction TrioCode Code Hopping Technology Every time a TrioCode transmitter is used a new security code is randomly generated from over 4 29 billion possibilities This greatly enhances the security of the system and makes
17. alled before setting the travel limits WARNING Use caution when operating the manual A release with the door open since it may fall rapidly due to weak or broken springs or an improperly balanced door CAUTION Do not disengage the opener to manual operation with children persons or any objects including motor vehicles within the doorway a Engage the C Rail s trolley attached to the door via the arms with the chain index by moving the door Ifthe trolley does not click firmly onto the chain index ensure that the manual release cord is not in the disengaged position by pulling it backwards b Turn on the power to the opener The CLOSE LIMIT LED will be flashing c Remove the button cover with a small blade screwdriver Fig 28 d Press and hold the MINUS button the door will OPEN start closing Fig 29 MARGIN e Release the MINUS button when the door is near LIMIT SET the desired closed position Single presses of the CLOSE MINUS button will inch the door closed ene If the door overshoots press the PLUS button LIMIT ME to move the door in the open direction A When the door is at the desired close position press the SET button to record the close limit position The OPEN LIMIT LED will now flash g Press and hold the PLUS button to open the door Fig 30 Release the PLUS button when the door is near the desired open position Single presses o
18. ble NOTE If the door is the only entrance to the garage and a battery back up kit is not fitted a keyed cable release should be fitted external to the garage Vacation mode A hand held transmitter can be programmed to lock and unlock all other transmitters that have been programmed into the openers memory The vacation mode can be used when the door is left idle for long periods of time Pet Pedestrian mode The transmitter can be programmed to open the door to an adjustable partial height so that the family pet can enter and exit the garage at any time You may also wish to open the door to a height suitable only for pedestrian access Auto close mode The opener can be programmed to automatically close after an open cycle The auto close time is adjustable It is compulsory to install a P E Beam if this mode is selected otherwise the door may cause personal injury or damage to property Photo Electric P E Beam optional The opener has an input to connect a P E Beam for extra safety and use of the auto close mode Manual operation The opener is equipped with a unique manual disengaging device If the power to the opener is disrupted the door can be put into manual mode by pulling down on the string handle on an angle towards the door This allows for manual operation of the door To re engage the opener pull the string handle away from the door Owner Installation Instructions GDO 9v3 SecuraLift O O Ope
19. d An operating force on the bottom rail should not exceed 150N 15kg force e Each month check that the opener reverses when the door contacts a 40mm high object placed on the floor AS3350 e NOTE If the door does not operate smoothly call your installer Service Record Yearly Automatic Technology suggests you contact your installer to perform an annual door service CAUTION Frequently examine door particularly cables springs and mountings for signs of wear damage or imbalance Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury AS3350 Adjustments should only be carried out by experienced persons as this function can be dangerous if not performed under strict safety procedures WARNING Failure to maintain your garage door may void the warranty on your garage door opener Record any maintenance in the following table to assist in any warranty service Date Service by Signature Invoice No Amount Owner Installation Instructions GDO 9v3 SecuraLift O 33 Ou ONN SERSSE SBSnorcce Ssssseees fig Gs e e n LO L 0890 C RIVOE TOXLNOO 38958 raLift Owner Installation Instructions GDO 9v3 Secu Q O Warranty and Exclusion of Liability 10 11 13 This warranty is an addition to any non
20. d when closing Opener overloaded Door in open position with Auto Close mode selected Pet Mode Engaged Mains power interrupted Service Due OPEN LED Green Flashing Flashing Flashing Alternating flashes One second flashes On Rapid flashes ei Ko 9 Ap STATUS Red LED Yellow Flashing Flashing Flashing Alternating flashes O GDO 9v3 SecuraLift Owner Installation Instructions Beeps as door moves 3 Beeps At The Start Of Each Cycle Parameters Button Functions OPERATE DOOR CODE LIGHT CODE FORCE MARGIN SET amp PLUS FORCE MARGIN SET amp MINUS FORCE MARGIN SET then SET AUTO CLOSE TIME then PLUS AUTO CLOSE TIME then MINUS AUTO CLOSE TIME then SET MINUS for 6 secs PLUS for 6 secs SET then power on amp hold until all LEDs are off DOOR CODE then power on amp hold until all LEDs are off SET amp DOOR CODE the power on and hold until all LEDs are off SET Opens Stops Closes the door Codes a transmitter button for operate vocation auxiliary and pedestrian functions Codes a transmitter button for light function Increases the obstruction force margin setting Decreases the obstruction force margin setting Resets the factory default force margin settings Increases the auto close delay time Decreases the auto close delay time Resets the factory default auto close delay time Clears the door limits set posit
21. distance in the C Rail Maximum door opening Width Height Weight Minimum Clearance Bottom of C Rail to highest point of door travel Short term peak force Lift force Nominal force Receiver type Receiver code storage capacity Transmitter frequency Coding type Number of code combinations Code generation Transmitter battery Courtesy light Controller fuse Step Maximum 4 Mins 1 12 1 Sec 255 Secs 230V 240V AC 50Hz 24V DC 2 2 Watts 100 Watts 24V DC permanent magnet 2 8m approx standard 5m with extended C Rail 5500mm 16 5m 3000mm 100 kg 25mm 800N 80kg 500N 50kg 150N 15kg UHF 433 92 MHz AM Receiver 24 x 4 button transmitter codes to 433 92 MHz Multi frequency Code hopping Over 4 29 billion random codes Non linear encryption algorithm CR 2032 3 Volts Festoon style 24 volts 15 watts lamp 10A slow blow NOTE Intermittent operations may occur in areas which experience very strong winds The strong wind puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system intermittently Photo electric beams must be installed if the closing force at the bottom edge of the door exceeds 400N 40kgf Owner Installation Instructions GDO 9v3 SecuraLift O 29 30 Parameters Door Status Indicators Door Opener State Open Close Opening Closing Door travel stopped Door obstructed when opening Door obstructe
22. e assembly Join to chain index with chain links supplied Fig 07 Idler pulley Shuttle with hole side toward the door Owner Installation Instructions GDO 9v3 SecuraLift O 11 Knockdown C Rail Assembly Note Use the 12 teeth sprocket with Gdo 9v3 opener Centre of the track GDO 9v3 SecuraLift Owner Installation Instructions Engage the shuttle with the chain index and move shuttle assembly to the centre of track Make sure the chain is engaged into the sprocket and also wrapped around the centre of the pulley Use a spring scale to measure required force to pull the shuttle adjust 1 2 tension hex bolt Fig 09 to tension the chain Move the shuttle back to the centre of the track to re test the force with spring scale Fig 10 Continue to adjust adjust the tension hex bolt until a force of 8kg to 8 5 Kg is achieved C Rail Attachment Step 2 Secure C Rail to Drive Unit a Locate and insert the shaft of drive unit into the track s sprocket Fig 11 b Fix the two track brackets with four screws supplied in accessory pack Fig 12 g Hex flange screw taptite 5 M4 x 10 Track bracket x2 Owner Installation Instructions GDO 9v3 SecuraLift O Step 3 Determine Door Type Determine which type of garage door you have as illustrated below Fig 13 to Fig 15 For a sectional panel door on tracks Fig 13 proceed with the installation from Step 4
23. en the button is released NOTE The safety obstruction detection is inoperable when the CLOSE button is used to move door 09 PLUS button green is used during installation to help set the open limit position Pressing and holding this button will move the door in the open direction releasing stops the door NOTE The safety obstruction detection is inoperable when the PLUS button is used to move door 10 CLOSE LIMIT LED red the LED is very helpful during installation It illuminates and flashes when the door is closing and remains steady on when the close limit position has been reached OPEN LIMIT LED green the LED is very helpful during installation It illuminates and flashes when the door is opening and remains steady on when the open limit position has been reached AUTO CLOSE TIME button White is used to adjust the auto close time While holding in the AUTO CLOSE TIME button and then pressing the PLUS button the time is increased Each press will increase the time by 1 second Pressing the MINUS button will decrease the time FORCE MARGIN SET Button The obstruction force margin is set automatically during installation The margin can be adjusted manually using the Force Margin Set button White Holding the Force Margin Set button and pressing PLUS or MINUS buttons will increase or decrease the amount of force The Force Margin Set should only be used if environmental factors wind etc affect the doo
24. er is not intended for use by young children or infirm persons without adequate supervision Children should be supervised to ensure that they do not play with the remote transmitters or the opener Keep hands and loose clothing clear of the door and door opener at all times O GDO 9v3 SecuraLift Owner Installation Instructions Important Safety Instructions The unit should be installed so that it is protected from the elements It should not be exposed to water or rain It is not to be immersed in water or sprayed directly by a hose or other device The garage door must be well balanced Sticking or binding doors must be repaired by a qualified garage door installer prior to installation of the opener Frequently examine the installation in particular cables springs and mountings for signs of wear damage or imbalance DO NOT use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury DO NOT attempt to repair the door yourself as hardware is under extreme tension Remove or disengage all garage door locks and mechanisms prior to installation of the opener Connect the opener to a properly earthed general purpose 240V mains power outlet installed by a qualified electrical contractor Disconnect the power cord from mains power before making any repairs or removing covers Only experienced service personnel should remove covers from the opener When
25. espond Step 19 2 Deleting All Transmitter Codes a b GDO 9v3 SecuraLift Owner Installation Instructions 1 Turn off power to the opener While switched off press and hold the DOOR CODE BUTTON Fig 44 Turn on power to the opener while holding this button The OPEN LIMIT CLOSE LIMIT and DOOR STATUS LEDs will illuminate for about five seconds These LED s will turn off and the CODING LED will illuminate Release the DOOR CODE BUTTON All stored codes will now be deleted Confirm this pressing buttons on any previously coded transmitters the opener should not respond P E Beam amp Auto Close A WARNING Photo electric beams must be installed if the closing force at the bottom edge of the door exceeds 400N 40kgf Step 20 Fitting the P E Beams optional a Affix the P E Beams in a strategic location within the doorway We recommend 150mm above the floor level and as close as possible to the door opening inside the garage Connect the wires from the P E wiring harness to terminal block Fig 45 The wiring diagram is for Model PE 2 Order Code 90214 Make sure to align the beams correctly Follow the manual supplied with the P E Beams A WARNING When using Auto Close Mode and P E Beams the doorway must be clear of all obstructions and persons at all times The location of the beam sand manner in which it is installed might not give safety protection at all times Check to make sure t
26. f the PLUS button will inch the door open Ifthe door overshoots press the MINUS button to move the door in the open direction WARNING Once the next step is performed the AN door will automatically close and open to calculate force settings Keep persons and objects clear of the door until it stops and the opener sounds a beep OPEN FORCE hey i Press the SET button to store the open limit Please read the above warning LYE US CLOSE ZS E Q Stee Step 14 2 Resetting Travel Limits To reset the limits press and hold the MINUS button for 6 seconds until the CLOSE LIMIT LED flashes quickly If no action is taken within 30 seconds the opener will return to normal operating mode and restore the original settings LIMIT 18 O GDO 9v3 SecuraLift Owner Installation Instructions Setting Limits via Transmitter The GDO 9v3 has the alternate ability to set travel limits using the transmitter allowing free movement around the garage to better assess the desired limit positions Step 15 1 Code a Transmitter for Limit Setting a Ensure the opener is powered up b Press and hold the DOOR CODE button Fig 31 c Press Button 1 on the transmitter for two seconds Fig 32 Release and pause for two seconds Press the Button 1 again for two seconds d Release the DOOR CODE button Step 15 2 Setting Limits via Transmitter a Engage the C Rail s trolley attached to the
27. hat the height of the beam and type used give maximum protection possible Step 21 Setting Up Auto close Mode A IMPORTANT NOTICE It is compulsory to have P E Beams installed when using Auto close mode Auto close mode is a function that automatically closes the door a preset time after the P E Beams recognise that a vehicle has left the garage The Auto close timer only starts after the P E Beam s path is broken the Auto close timer has been set If the P E path is not broken the door will remain open until the path is broken If the opener incurs a physical obstruction i e not from the P E Beams while closing the door will re open and not Auto close until the P E Beam s path is broken again Step 21 1 Setting Auto close Time a b Hold down the AUTO CLOSE TIME button Fig 46 While holding in the AUTO CLOSE TIME button press the PLUS button each press will add one second to the Auto close delay To decrease the delay time follow Step 21 1 a and press the MINUS button each press will deduct one second from the Auto close delay Press the OPERATE button or transmitter to open the door When the door is fully opened the OPEN LIMIT LED will flash to indicate that Auto close mode is operational Break the P E Beam s path momentarily to initialise Auto close When the door reaches the fully opened position the door will pause for the set Auto close time and then close Model
28. id and sound so as to form a secure mounting platform Step 6 Attach the Rail to the Wall Bracket a Attach the C Rail assembly to the wall bracket with the 90mm long clevis pin and secure with the supplied snap pin Fig 18 Leave the powerhead in its packing box for protection during installation Step 7 Secure the Powerhead to the Ceiling a Raise the powerhead from the packing box and support it in the horizontal position with a step ladder Open the garage door Rest the opener on the open door and use a scrap piece of wood to bring it to horizontal level Line up the track perpendicular to the wall Secure the perforated angle not supplied to the ceiling above where powerhead s mounting holes will be once fully installed A representative mounting is shown Fig 19 Connect the powerhead to the ceiling mounted perforated angle with M8x20mm screws and nuts Strips should not extend more than 18mm below centre of powerhead mounting holes Go to Step 12 on page 17 Owner Installation Instructions GDO 9v3 SecuraLift 16 Mounting on a non Track Type Door Centre of Door lt Highest point of door travel Step ladder Drill hole at centre of track recommended bolt size M6 or M8 Aluminium rail Shuttle VP2 assembly HEIGHT OF BOLT HEAD O GDO 9v3 SecuraLift Owner Installation
29. ing the Opener Setting Travel Limits Control Panel Setting Travel Limits Transmitter Safety Obstruction Forces Safety Obstruction Force Test Adjusting Safety Obstruction Forces Coding Transmitters Door Vacation Mode Auxiliary out put Pet Mode Courtesy Light Remotely Coding Transmitters Erasing Transmitter Codes 10 11 11 13 14 15 16 17 18 18 19 20 20 21 22 22 22 22 22 23 24 24 Accessories Photo Electric Beam Installation Auto Close Setup SmartSolar Installation Battery Back Up installation Final Set Up Courtesy Light Time Pet Mode Door Height Wall Mounted Transmitters Re Initialising Parameters Default Settings amp Specifications Door Status Indicators Button functions Troubleshooting Guide Maintenance Record Parts Listing Warranty Owner Installation Instructions GDO 9v3 SecuraLift O 25 25 25 26 27 28 28 28 28 28 29 29 30 31 32 33 34 35 Important Safety Instructions WARNING It is vital for the safety of persons to follow all instructions Failure to comply with the following Safety Rules may result in serious personal injury and or property damage CAUTION If your garage has no pedestrian entrance door an emergency access device should be installed This accessory allows manual operation of the garage door from outside in case of power failure For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric P E
30. ion Code transmitter into opener s memory Refer Step 18 1 on page 22 Replace battery Reset limits positions Refer Step 15 3 on page 19 Reset limits positions Refer Step 15 3 on page 19 Replace lamp Repair P E Beam or replace wiring Re align optics See P E instructions Remove obstruction from the path of P E Beam Remove obstruction See Step 21 on page 25 Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones wireless stereo headphones and baby monitors It is possible that these devices could cause a degree of interference such as to greatly reduce the range of the transmitter In such an instance please contact your ATA dealer for an alternative frequency replacement kit As this is not a warrantable situation but an environmental issue charges may apply for the changeover O GDO 9v3 SecuraLift Owner Installation Instructions Maintenance Maintenance Whilst your opener does not require any periodic maintenance the door that it is fitted to does Your garage door is a large heavy moving object and should be tested regularly to ensure it is in good condition A poorly maintained door could cause fatal or serious injuries or serious damage to property To ensure a long and trouble free life for your opener the following is recommended Monthly e Disengage the opener and manually operate the door The door must be smooth to operate by han
31. ions Limits then need to be reset Enters pet pedestrian position mode Deletes control parameters excluding transmitter storage memory Deletes all transmitter storage memory Deletes all control parameters and transmitter storage memory Re initialises the Opener to re calculate force margin Owner Installation Instructions GDO 9v3 SecuraLift O 31 32 O Troubleshooting guide a Teme Door will not operate Door starts to close but automatically reverses to open position Gate operates from drive unit operate button but not from transmitter See note Door will not close fully Door will not open fully Courtesy light not working Auto close not working PLEASE NOTE Mains power not switched on Door is obstructed Door is locked or motor jammed Door tracks hardware damaged Adverse weather conditions wind or cold causing door to stiffen and become tight in the tracks Possible obstruction in the doorway Transmitter code not stored in memory Flat battery Door limits position need to be reset Door limits position need to be reset Faulty light PE Beam or wiring faulty PE Beam not aligned correctly PE Beam is obstructed Door obstructed when closing Auto close time not set Switch on mains power Remove obstruction Unlock door or remove jam Door requires service repair by qualified technician Increase force margin setting See Step 17 on page 20 Remove obstruct
32. o theft fire flood rain water lightning storms or any other acts of God e maximum continuous operating time exceeding one 1 minute in ten 10 f maximum operating force exceeding 15kg 150N when moving the door manually to the open or closed position g door surface area and or weight exceeding 16 5m and 100kg respectively h door not in safe and correct working order and condition i evidence of unauthorised repairs j any cost relating to damage caused by misuse negligence or failure to maintain the equipment in a proper working order as per clauses d through h k installation adjustment or use which is not in accordance with the instructions set out in installation instruction manual I attempted or complete modification or repairs to the product carried out by a person who is not authorised or has not been trained by ATA to carry out such modification or repairs m faulty or unsuitable wiring of structure to which the product is fixed or connected n radio including citizen band transmission or any electrical interference 0 damage caused by insects p loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there from or any consequential loss q any cost or expense arising due to manufacturer recall of any product r any cost or expense due to negligence of the approved service provider s installation of a residential garage door opener in a commercial or indus
33. on a panel with insufficient strength The opener s warranty does not cover damage caused to the door and or door panels Step 13 Attaching the Arms FOR SECTIONAL AND ONE PIECE DOORS WITH TRACK a Assemble the bent arm connecting to the door to the right side of the straight arm connecting to the shuttle with bolts and nuts supplied in the accessory pack Fig 25 Always use both bent and straight arms b Connect the assembled arm to the bracket and the disengaged trolley with clevis and snap pins The angle A must be more than 10 Fig 26 WARNING Connecting the bent arm other way around may damage the door The straight arm should not protrude beyond heal of bent arm FOR ONE PIECE DOORS WITHOUT TRACK a Assemble the bent and straight arms as shown in Fig 27 with bolts and nuts supplied in the accessory pack Always use both the bent and straight arms b Connect the assembled arm to the bracket and the disengaged trolley with clevis and snap pins c If installing on a door with a bad wave action lengthening the arm will assist in reducing this effect IMPORTANT NOTE Adjust the length of the cord so that its toggle is no more than 1 8m from the ground BT TTS Bye ty CT Sa eee Arm connected to the shuttle Owner Installation Instructions GDO 9v3 SecuraLift O Setting Limits Step 14 1 Setting Travel Limits NOTE If P E Beams are to be used they must be inst
34. on third press Fig 40 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 second c Release the DOOR CODE button d Press the transmitter button to test Step 18 4 Code a Transmitter Button for Pet Pedestrian Mode a Briefly press the DOOR CODE button three times then press it again and hold will beep four times on fourth press Fig 41 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release the DOOR CODE button d Press the transmitter button to test To change the default pet pedestrian door opening position refer Step 25 Coding Transmitters Step 18 5 Coding a Transmitter Button to the Courtesy Light The transmitter can be programmed to operate the courtesy light on the opener independently of the door moving a Press and hold LIGHT CODE button Fig 42 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release the LIGHT CODE button d Press the transmitter button to test PEN eons q CLOSE EN Owner Installation Instructions GDO 9v3 SecuraLift O 23 24 Remote Coding amp Deleting Transmitters O 28905 e Step 19
35. oor to the desired pet mode open position c Press the SET button to record the new position When activated Pet Mode drives the door to the preset position from either above or below Pet Mode s active status is indicated by both the OPEN and CLOSE LIMIT LEDs being illuminated If a Pet Mode button is pressed while the door is moving the door will stop If a Pet Mode button is pressed when the door is in the Pet position then the door will close Step 26 Installing the Wall Mounted Transmitter Optional a Remove the faceplate from the transmitter b Affix the baseplate in a convenient wall location that is out of reach of children and convenient to the customer Fig 53 Make sure the door is visible from this location c Replace the faceplate d To code the transmitter see Steps 18 1 through 18 5 on page 21 and 22 Step 27 Reset all Factory Defaults a Turn power to opener off b Press and hold the SET Button Fig 54 c Turn power on while holding the SET button Continue to hold until all LEDs are off This will not erase transmitter codes stored in memory Default Settings amp Specifications Factory default settings Default Maximum motor run time 60 Secs Courtesy light time 3 Mins Obstruction force margin 2 Auto close time 0 Secs Technical specifications Power supply Transformer rating Standby power Motor power Motor type Shuttle travel distance in the C Rail Maximum shuttle travel
36. r firmly and the door should stop If the door does not reverse readily when closing or stop when opening the force may be excessive and need adjusting refer below DANGER If the door fails these tests put the opener into manual mode only operate the door by hand and call for service Adjusting Safety Obstruction Forces Adjusting Safety Obstruction Force The Safety Obstruction Force is calculated automatically during setup Adjusting this is normally only necessitated by environmental conditions such as windy or dusty areas and areas with extreme temperature changes WARNING Photo electric beams must be installed if the closing force at the bottom edge of the door exceeds 400N 40kgf Step 17 1 To Increase Force Pressure a Hold down FORCE MARGIN SET button Fig 35 b While holding the FORCE MARGIN SET button press the PLUS button Each press increases the force margin Fig 35 c The OPEN LIMIT LED will flash each time the PLUS button is pressed to indicate a force increase If the OPEN LIMIT LED on continuously when pressing the PLUS button this indicates that the maximum setting has been reached d Test the force again as per Steps 16 1 and 16 2 Step 17 2 To Decrease Force Pressure a Hold down FORCE MARGIN SET button Fig 35 b While holding the FORCE MARGIN SET button press the MINUS button Each press decreases the force margin Fig 35 c The CLOSE LIMIT LED will flash each time
37. r s operation JP1 SOLAR CONNECTOR onto this the shunt must be fitted for solar operation PROG INPUT is used to connect the Automatic Technology Handheld Programmer PG 3 for editing control and receiver functions accessing diagnostic tools and activating special features and operating modes SBY 3 CONNECTOR is used to connect both Battery Back Up Kits and SmartSolar kits O GDO 9v3 SecuraLift Owner Installation Instructions iO 10A FUSE Owner Installation Instructions GDO 9v3 SecuraLift O 9 Drive Unit 1x GDO 9v3 SecuraLift Trio drive unit Fig 02 1x TrioCode Transmitter pack Fig 02 Pack includes two keyring transmitters and batteries 1x Wall mount transmitter with battery Fig 02 2 x Door attachment arms Fig 02 1 x Accessory and hardware pack Fig 02 1 x Installation Manual PLUS Pre Assembled Single Piece C Rail NOTE The chain or belt in the one piece rail has been tensioned by the factory IMPORTANT NOTE If a modification to the length of the track is required the adjustment must be made from
38. rating controls 01 Terminal Block 24V PWR is used to power devices such as PE Input for photo electric beam for safety and auto close function LGT Input allow hard wired external trigger for the opener s courtesy light O S C INPUT is used for the connection of a wired switch momentary contact This switch can then be used to open stop or close the door Install the wall switch in a location where the switch is out of reach of children and the garage door is visible 02 SET button orange is used during the installation phase together with the Open and MINUS buttons to set the door limit positions The Set button is also used to re initialize the Opener 03 LIGHT CODE button white is used for storing or erasing the transmitter button code you wish to use to switch the courtesy light on the opener on or off 04 CODING LED red light flashes when a code is being stored or when a transmitter button is pressed 0s OPERATE button Yellow is used during installation to test the open stop and close cycles for the opener The opener has to be initialised by the Reset button to make the O S C button operable DOOR CODE BUTTON blue is used for storing or erasing transmitter buttons for door operation DOOR STATUS LED Yellow 0s MINUS button red is used during installation to help set the close limit position Pressing and holding this button will move the door in the close direction Movement stops wh
39. s JP1 Solar connector Fig 48 IMPORTANT WARNING Do not connect battery or solar panel polarity incorrectly this will result in serious damage to components Step 22 2 Connect the Solar Panel a b Mount the solar panel as outlined in the SmartSolar Installation Manual Feed the Solar Panel s cable through black grommet located on the top of the plastic drive unit cover Connect the red wire to the Charger Board s SOLAR connector and the black wire to the SOLAR connector Fig 49 WARNING During Step 22 3 the opener will become active Step 22 3 Mount amp Connect the Battery Mount the Battery Box close to the opener Feed the 2 core 18awg gauge cable supplied through the Battery Box s grommet Connect the red wire to the Battery Box s terminal and the black wire to the terminal Fig 50 Feed the other end of the battery cable through the drive unit s black grommet Connect the red wire to the Charger Board s BAT connector and the black wire to the BAT connector Fig 49 Refit the light diffuser and main cover Step 22 4 Re setup and Test the Opener a b Setup travel limits and code transmitters as per the GDO 9v3 instruction manual Press either the OPERATE button or use a transmitter to operate the opener Battery Back Up Installation Wiring diagram 7 of 6 Pee CA Item Description Q
40. the MINUS button is pressed to indicate a force decrease If the CLOSE LIMIT LED on continuously when pressing the MINUS button this indicates that the maximum setting has been reached d Test the force again as per Steps 16 1 and 16 2 Step 17 3 To Recall Factory Set Force a While holding down the FORCE MARGIN SET button press the SET button for two 2 seconds Fig 36 b Release both buttons The default setting should now be recalled Step 17 4 To Recalculate Force Margins a Press and hold the SET Button for two 2 seconds the beeper will sound once Fig 37 b The door will start to move and re calculate force margins The door can move between the open and close limit positions up to four 4 times depending on the position of the door and the power up condition c A single beep will be heard once the process is complete d Test the force again as per Steps 16 1 and 16 2 amp D lt DS OPEN n LIMIT CLOSE ur VE OPEN O ES LIMIT Ney CLOSE RI OSE Q ee OPEN Fores Q ss Owner Installation Instructions GDO 9v3 SecuraLift O O Q D O amp U um Seer gt CLOSE 4 sam que Z EN ERATE DI O E V yy unirr NSE poor _ staws _ SE J O Gre Ny NY SET creme New wy O e Xr oR sTaTus CICCIONE R 7 AAQBAaZEe y ae
41. trial situation or a non single residential dwelling ATA s liability under this warranty is limited at ATA s absolute option to replacing or repairing the product which ATA in its unfettered opinion considers to be defective either in material and or workmanship or to credit the dealer with the price at which the product was purchased by the dealer This warranty does not extend to cover labour for installation This warranty is limited to Return to Base RTB repair and does not cover labour for on site attendance This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging This warranty is only applicable for repairs to the product carried out within Australia This warranty does not cover consumable items including globes batteries and fuses This warranty is not transferable Where the Product is retailed by any person other than ATA except for the warranty set out above such person has no authority from ATA to give any warranty or guarantee on ATA s behalf in addition to the warranty set out above NOTES 1 One 1 cycle one 1 open and one 1 close action of the door or gate 2 This warranty is to be read in conjunction with the owner s copy of the installation instruction manual 3 The door should be balanced in such a way that the user manually is able to open or close the door without using force not greater than 150N 15kg although a greater force may be required
42. ty Order Code ll Batteries cover 1 16460 2 Batteries support 1 16480 3 Battery 12v sec 12 2 2Agm type 2 15470 4 Battery coupling wire esv 24 1 12005 5 Battery harness 1 15670 6 Pan head screw w washer m4x8 2 10320 Ta Cable clamp acc 1 5 3 16 1 11750 8 SBY 3 version 1 00 1 00852 9 SBY 3 esv24 charger harness 1 14115 10 SBY 2 battery harness 1 15560 Battry pack 1 11 Hex stand off m4 2 11190 12 Thruss separation hd screw 6 10503 13 Pan head screw w washer m4x8 4 10320 14 Taptite screw p m4x8 3 10580 15 Bracket ra 31x20x31 2 02508 16 Pcb support 76x27 1 16421 17 Cable clamp acc 2 5 5 16 1 11760 Step 23 1 Connect the Battery Back Up Kit a b C d A g h Disconnect power to the opener Remove screws and swing open the cover Fig 51 Mount the PCB support with two screws item 12 Secure the SBY 3 Charger Board onto the pcb support with three 3 screws item 14 Feed the 2 wire battery harness item 5 through the grommet on the base plate and connect to SBY 3 Feed charger harness from SBY 3 to the control board and plug into the 4 pin connector marked SBY 3 onto the control board Mount battery pack and secure with item 6 and 11 WARNING After Step 23 1 g the opener may become active even when power is off This is a result of a residual charge in the batteries Connect battery harnesses item 5 and 10 together Fig 51 Reconnect power
Download Pdf Manuals
Related Search