User Manual - Hear and Learn
Contents
1. AUDIO MICROPHONE INPUT Use this input to plug in a laptop MP3 player or other audio source to wirelessly transmit audio to be played through the system Alternatively an external microphone can be connected CHANNEL SELECT SWITCH CH A B This switch allows for selection between Channel A or B If you are using a single microphone we recommend using Channel A CHARGER CONTACTS These contacts interface with the charging tabs in the BC RMCC cradle charger for daily charging Simply place the REDMIKE in the charger 3 Optional 5 Warrant fe prena 4 Troubleshooting 5 Warranty satety Accessories amp Specifications 2 Setup amp Use 1 Overview CRADLE CHARGER CONTROLS AND CONNECTIONS 4 Troubleshooting z E 1 CHARGE INDICATORS The light 2 DC POWER PORT Connect the 6 glows RED while the REDMIKE is DC power cord here charging When fully charged the 3 OPTIONAL CHARGING PORT light will glow GREEN A blinking Plug the charging cord for the RED light indicates that no battery optional LT 71 or the REDMIKE is sensed REDMIKE Yellow Protective Tab may not have been completely removed see page 5 item 4 A blinking Green LED means a non Lightspeed battery has been installed possibly an alkaline battery Share microphones here 10 SECTION 2 SET UP amp USE 1 LOCATION OF THE RECEIVER First find a suitable location to set up the CAT 82. 4 While speaking in a normal voice increase the B VOLUME on the CAT 805iX level until your voice is barely audible REMEMBER This equipment is designed to supplement and distribute the user s voice so they are able to speak in a conversational tone Having the volume set too high will result in feedback and listener fatigue 5 Warranty Safety amp Specifications 4 Troubleshooting 2 Setup amp Use e Opinel Accessories 1 Overview 27 28 5 Warranty Safety amp Specifications 3 Optional Accessories 4 Troubleshooting 2 Setup amp Use 1 Overview INITIAL SET UP OPTIONAL IR MEDIA CONNECTOR 1 Turn off the second microphone The iR Media Connector uses the same channel channel B as the optional second microphone REDMIKE LT 71 or REDMIKE Share As a result they cannot be used simultaneously If you have a second microphone turn it off before transmitting audio from the iRMC NOTE If you adjust the CH B volume on the classroom audio system you will also be changing the volume for your second microphone Return the CH B volume knob to the original position before turning the second microphone back on 2 The iR Media Connector volume is preset for most standard audio signals If you need to turn the volume up or down follow this procedure A Adjust the volume at the computer television or other audio source if possible B If the audio so
3. WARRANTY SAFETY amp SPECIFICATIONS FIVE YEAR LIMITED WARRANTY Lightspeed Classroom Audio Systems are guaranteed against malfunction due to defects in materials and workmanship for a period of FIVE 5 YEARS beginning at the date of the purchase invoice If such malfunction occurs the product will be repaired or replaced at Lightspeed s option without charge during the warranty period Lightspeed s Warranty Exchange Program applies to all infrared systems within the five 5 year warranty period If an infrared product or component has an issue that requires service a refurbished replacement will immediately be sent to the customer to minimize downtime Customers will receive the exchange product s or component s within 2 3 days A prepaid return label will be included with exchanged products so original malfunctioned equipment can be returned to Lightspeed Any exchanged equipment will remain covered under the original five 5 year warranty 1 Warranty on infrared microphones is FIVE 5 YEARS 2 Warranty on Lightspeed NiMH rechargeable batteries is one 1 year 3 Prepaid shipping label provided by Lightspeed for warranty repairs within the U S Customers outside the U S should refer to the Lightspeed website www lightspeed tek com for warranty repair instructions 4 Warranty does not extend to finish appearance items or malfunctions due to abuse or operation other than specified conditions nor does it extend to inc
4. YELLOW PROTECTIVE TAB Slide the battery compartment door and remove this disposable protective tab before use AUDIO MICROPHONE INPUT Use this input to plug in a laptop MP3 player or other audio jog qer nowy loop fuaneq opts es source to wirelessly transmit audio to be played through the system Alternatively an external microphone can be connected CHANNEL SELECT SWITCH CH A B Use this to choose Channel A or B If you are using a single microphone we recommend using Channel A VOLUME CONTROLS UP DOWN CHARGER CONTACTS These contacts interface with the charging tabs when the REDMIKE VC is placed in the BC RMCC cradle charger REDMIKE VC Charging E Before use the REDMIKE VC should 8 be charged See page 16 and gt M follow the same instructions for the REDMIKE 3 F REDMIKE VC Initial Set up See page 17 and follow the same instructions for the REDMIKE to setup the REDMIKE VC 3 Optional Accessories NOTE A nominal volume level must be set on the CAT 805iX before adjusting controls on the REDMIKE VC The teacher can now use the controls on the REDMIKE VC to adjust the volume level from anywhere in the room The microphone volume control has 4 steps up and 4 steps down from the mid point 9 levels total 2 Setup amp Use 2 o gt O 21 22 4 Troubleshooting 3 Optional Accessories 2 Setup amp
5. lightspeed CAT 805iX Infrared Wireless Microphone System User Manual TABLE OF CONTENTS SECTION 1 Overview SECTION 2 Set up amp Use SECTION 3 Optional Accessories SECTION 4 Troubleshooting SECTION 5 Warranty amp Specifications s O00 00 5 i m X mn Ses ves ees CON 9 20 20 21 21 22 22 23 24 25 25 26 27 28 29 29 30 31 32 33 34 35 System Components and Unpacking Optional Components Front Panel Controls Rear Panel Controls ISR Connections REDMIKE Controls and Connections Cradle Charger Controls and Connections Step 1 Location of the Amplifier Step 2 ISR Sensor Installation Step 3A Connect the power supply Step 3B ISR connection Step 3C Connect CAT 805iX to an amplifier Step 4 Charging the REDMIKE Step 5 Operating the REDMIKE Using REDMIKE to Amplify External Audio Equipment REDMIKE VC Controls and Connections Charging Initial Set Up LT 71 Controls and Connections Charging Initial Set Up REDMIKE Share Controls and Connections Charging Initial Set Up iR Media Connector Audio Integration Other Optional Accessories Troubleshooting Guide Tips to Maintain Optimal Audio Performance Warranty Statement Safety Instructions Safety Warnings and Certifications System Specifications Optional 4 Troubleshooting Warranty Safety Accessories E amp Specifications 2 Setup amp Use 1 Overview SECTION 1
6. Use Overview 1 1 ON OFF MUTE Switch CHANNEL SELECT SWITCH CH A B Use this to choose Channel A or B If you are using a single microphone we recommend using Channel A POWER CHARGE INDICATOR A BLUE light indicates the REDMIKE VC is on and fully charged A RED light indicates a charge is needed EXTERNAL MICROPHONE INPUT MIC Use the 3 5mm MIC jack for the optional TK 250 headset microphone partit MC TK250LTM OPTIONAL LT 71 Controls and Connections LT 71 e AUXILIARY AUX Plug a laptop MP3 player or other audio source into this jack to wirelessly transmit the audio signal to be played through the system CHARGER INPUT CHARGER Plug the charging cable from the charger into this jack for daily charging The LED on the front will glow RED to indicate charging LT 71 Charging 1 Ensure that the LT 71 is turned E D OFF Z5 2 Make sure the cradle charger is plugged into a wall outlet Connect one end of the charging 2 cable into the jack labeled E CHARGER on the side of the 3 LT 71 and plug the other end into 3 the charging jack on the rear of E the REDMIKE cradle charger The LT 71 s rechargeable batteries are factory installed The LED on the front of the LT 71 will glow RED when charging 3 Leave the LT 71 plugged in overnight 8 10 hrs to obtain a full charge 3 Optional Accessories 2 Setup amp Use z 5 2 6
7. amp Specifications 4 Troubleshooting Accessories 2 Setup amp Use 1 Overview INFRARED SENSOR RECEIVER ISR CONNECTIONS 1 POWER INDICATOR This light send audio from the microphones will glow blue when the ISR is to the CAT 805iX preamp receiving power from the CAT 4 IR EXPANSION Connect up to 805iX three passive IR sensors IR SR7OF 2 A B IR INDICATORS These lights to this connection for larger glow when the corresponding classrooms For more than one microphone set to channel A or additional sensor a 3 way coax B is turned on and transmitting splitter is required HS3 A steady light indicates a strong signal 3 SENSOR OUT Connect the Cat 5 sensor cable to this connection to REDMIKE CONTROLS AND CONNECTIONS POWER BUTTON Press this button to turn the REDMIKE ON press again to turn it OFF mute POWER LOW BATTERY INDICATOR A BLUE light indicates the REDMIKE is on and fully charged A RED light indicates a charge is needed BATTERY COMPARTMENT To access the battery compartment slide the door downward The battery should only be replaced by a Lightspeed AA rechargeable sensing battery part BA NH2A27 YELLOW PROTECTIVE TAB Slide the battery compartment door open to remove this disposable protective tab before use NOTE do not attempt to remove the tab without first 5 opening the compartment door as it may tear leaving fragments
8. NOTE If the system was purchased without a REDMIKE or REDMIKE VC the LT 71 will utilize the BC TXLT wall charger Plug the wall charger into an AC outlet and plug the other end s into the CHARGER jack on the LT 71 23 LT 71 Initial Set up Once the LT 71 is charged follow these steps to set it up for use 1 Turn the CAT 805iX power switch to the ON position The RED LED on the switch will glow 2 Turn on the LT 71 and set the operating channel to B 3 Slip the LT 71 with lanyard around the neck and position the top of the microphone just below the collarbone NOTE Positioning of the LT 71 is critical for proper volume adjustment 3 Optional Accessories 4 While speaking in a normal voice slowly increase the volume for Channel B on the CAT 805iX until your voice is barely audible REMEMBER This equipment supplements the user s voice so they are able to speak in a conversational tone Having the volume set too high will result in feedback and listener fatigue 24 REDMIKE Share Controls and Connections 3 Optional Accessories 2 Setup amp Use MMMM YUL 1 POWER SWITCH 2 POWER CHARGE INDICATOR this light glows blue when turned on and turns off to indicate low battery level When charging the light glows red 3 AUDIO INPUT plug a laptop MP3 player or other audio device into this jack to wirelessly transmit the aud
9. OVERVIEW SYSTEM COMPONENTS AND UNPACKING The standard configuration of the CAT 805iX will contain CAT 805iX Preamp GAT S053 hired Wisless Microphone Satem Preamp Power Supply ISR Infrared Sensor Receiver and Cable Charging Cradle and Power Supply CZ REDMIKE 5 Classroom S Microphone cC OPTIONAL COMPONENTS Optional equipment which may be part of your CAT 805iX system REDMIKE vc Volume Control Microphone REDMIKE Share Handheld Microphone and Charger Cable LT 71 LightMic and Charger Cable Standard Accessories AC 805 Microphone preamp PS 24V 250 24V 250mA power supply for CAT 805iX RX ISR Infrared sensor receiver with mounting bracket CA P5E50 50 plenum rated Cat 5e cable RMT REDMIKE classroom microphone with battery BA NH2A27 AA NiMH rechargeable sensing battery for REDMIKE AC RMLC2 REDMIKE lavaliere cord BC RMCC REDMIKE cradle charger PS 5V 1 0 5V 1 0A power supply for cradle charger Optional Components RMV REDMIKE VC microphone with battery RMS REDMIKE Share handheld microphone with battery pack LT71 LightMic microphone with batteries BA NH2APK NiMH rechargeable battery pack for REDMIKE Share BA NH1 AA NiMH rechargeable battery for LT71 2 per microphone t 5 Wa t fe P Optiona 4 Troubleshooting 5 Warranty Safety Accessories amp Specifications 2 Setup amp Use 1 Overview 5
10. REDMIKE Share uses the BA NH2APK rechargeable battery pack The LT 71 requires two BA NH1 AA rechargeable batteries Make sure the microphones are turned off while charging so a full charge is attained Full charge will last eight hours Inspect the battery contacts Clean and adjust if necessary PROBLEM Hearing Static SOLUTION Follow these steps to eliminate static Ensure sensor is in optimum location refer to sensor placement in manual A single sensor will cover a 1600 sq ft enclosed classroom Ensure that no other REDMIKE LT 71 REDMIKE Share is operating on the same channel e Ifthe optional iR media connection is in use set the microphone to Channel A PROBLEM Low Volume or Feedback SOLUTION Follow these steps to eliminate low volume or feedback Ensure microphone is positioned appropriately just below the collar bone Check volume level on the amplifier If the volume is too high feedback will occur Adjust accordingly Adjust the volume level on the back of the optional REDMIKE VC Turn up the volume on the 805iX if volume seems too low If feedback occurs try turning down the volume on the CAT 805iX PROBLEM No Sound From Speaker SOLUTION Follow these steps to produce sound from speakers Turn the CAT 805iX on Confirm that the POWER light located on the front panel switch is on e Confirm signal is being received at the CAT 805iX The IR signal light w
11. To remove the ISR slide a ruler or screwdriver behind the ISR to press the release bar down and 2 Uncoil the Cat 5 sensor cable slide the ISR off the bracket Connect one end of the cable to the ISR Route the wire back to the CAT 805iX preamp securing it along with way using surface raceway where possible 4 Troubleshooting 4 Connect the other end of the Cat 5 sensor cable into the SENSOR INPUT jack on the CAT 805iX preamp 3 Slide the ISR onto the bracket until it clicks into place a Guide the mounting rails onto the bracket oriented as pictured 2 Setup amp Use 1 Overview 14 3A CONNECT THE POWER SUPPLY 1 Ensure the power button is depressed in the OFF position 2 Connect the DC end of the power supply to the 24VDC input 3 Connect the AC adapter end of the supply into a wall outlet CAT 805iX siad Ses i DC Power Source Cable 3B ISR CONNECTION 1 Ensure the power is still switched OFF 2 Check the connection from the ISR to the CAT 805iX Ensure the sensor cable is securely attached to the SENSOR INPUT jack and locked into place CAT 805iX Preamp ISR Sensor Receiver 2 Setup amp Use 3 Optional 4 Troubleshooting 5 Warranty Safety 1 Overview amp Specifications Accessories 15 16 5 Warranty Safety 3 Optional Accessories 4 Troubleshooting 2 Setup amp Use 1 Overview amp Specification
12. 05iX preamp It is best to put the preamp in a stable location near the amplifier to be used Media Cabinet Set up Avoid Separated Set ups Ideally the preamp should be located very near the amplifier being used Avoid long distances when possible to minimize wire runs and installation hassle 5 Warranty Safety amp Specifications a Options 4 Troubleshooting Accessories 2 Setup amp Use 1 Overview 11 5 Warranty Safety amp Specifications gt Optional 4 Troubleshooting Accessories 2 Setup amp Use 1 Overview 12 2 ISR SENSOR INSTALLATION Next find a suitable location for the ISR Poor location will cause substandard performance of the CAT 805iX IR Wireless Microphone System The ISR should be as high as possible in the room the ceiling is the best location centered along the longest wall in the room When possible use a conduit to protect the wires not included Poor choices for placement are corners on walls at heights lower than 7 feet 2 meters or in places where the line of sight from the ISR to the receiver is or could be obstructed Good placement Best placement Avoid Conduit is Recommended o 2 ISR SENSOR INSTALLATION coNr D Once you find a suitable location for the ISR follow these instructions to mount it There are different instructions for mounting depending on if the ISR will be mo
13. C 92 31 EEC 93 68 EED and 2004 108 EC Electromagnetic Compatibility Directives Lightspeed Technologies launched a formal product recycle program in Europe that complies with the European Union Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE Directive Please visit our website at www Lightspeed tek com for more information This product is manufactured using lead free processes and is free of other materials harmful to the environment It conforms to the most stringent new European guidelines for consumer products RoHS SYSTEM SPECIFICATIONS OVERALL SPECIFICATIONS Audio Output Level 500mV Frequency Response 100 Hz to 10 kHz 3 dB Carrier Frequencies IR 2 06 2 54 3 2 3 7 MHz Signal to Noise Ratio gt 73 dB Image and Spurious Rejection gt 70 dB RECEIVER SPECIFICATIONS Receiver Type Superheterodyne Receiver Sensitivity 6 uV for 60 dB S N Image and Spurious Rejection gt 70 dB Dimensions W x D x H 4 2 x 4 x 1 8 Weight 0 95 Ibs TRANSMITTER SPECIFICATIONS REDMIKE and REDMIKE VC Audio Distortion 196 Built in Microphone Unidirectional Electret Battery Power 1 year warranty 1 AA NiMH Rechargeable Sensing Battery Audio Input 3 5 mm Dimensions W x D x H 0 9 x 1 0 x 3 5 Weight 2 1 oz LT 71 LightMic Audio Distortion 196 Built in Microphone Unidirectional Electret Battery Power 1 year w
14. Warranty Safety amp Specifications 2 Setup amp Use Optional 4 Troubleshooting Accessories 1 Overview FRONT PANEL CONTROLS POWER SWITCH INDICATOR 3 A VOLUME Controls the volume Press this button to turn the CAT of the teacher microphone set to 805iX ON pushed in or OFF channel A bd the POWER is eb UD 4 B VOLUME Controls the volume the blue LED indicator will light of the student or second teacher AUDIO INDICATORS These microphone set to channel B lights flash red when audio voice from the microphone is detected REAR PANEL CONTROLS DC POWER Plug the power supply 24V 250mA into this jack MIXED OUTPUT This balanced output sends the audio from both microphones CH A and CH B to an input on an amplifier CH B OUTPUT This balanced output sends the audio from only the microphone set to CH B to an input on an amplifier CH A OUTPUT This balanced output sends the audio from only the microphone set to CH A to an input on an amplifier SENSOR INPUT The infrared microphone audio from the ISR is connected to this input via Cat 5 cable SENSOR SHORT This LED glows red when there is a short in the ISR or cable The system will not operate but is protected from damage when the LED is lighted 3 Optional 5 Warranty Safety Accessories 4 Troubleshooting amp Specifications 2 Setup amp Use 1 Overview 5 Warranty Safety
15. arranty 2 AA NiMH Rechargeable Audio Inputs Mic Level 3 5 mm Line Level 3 5 mm Dimensions W x D x H 1 375 x 75 x 4 625 Weight 3 7 oz REDMIKE Share Handheld Microphone Audio Distortion 1926 Built in Microphone Battery Power 1 year warranty Unidirectional Electret 1 AA NiMH Rechargeable Battery Pack Audio Input 3 5 mm Dimensions W x D x H 825 x1 3 x 1 3 Weight 7 9 oz ISR SENSOR SPECIFICATIONS Working Range Up to 1600 square feet per sensor Cable 50 ft Plenum rated Cat 5e Mounting Ceiling clip Wall bracket Dimensions 9 4 x 1 4 x 5 2 Weight 14 3 oz 5 Warranty Safety amp Specifications 4 Troubleshooting 2 Setup amp Use 1 Overview 3 Optional Accessories 35 liohtspeed AC MN 8 0 5 LIGHTSPEED TECHNOLOGIES 11509 SW HERMAN ROAD TUALATIN OR 97062 TOLL FREE 800 732 8999 PHONE 503 684 5538 FAX 503 684 3197 LIGHTSPEED TEK COM MN0234US01 2
16. ed daily they should be kept in the cradle microphones can be left in a charging cradle constantly for up to 2 weeks without causing degradation to battery life A red light on the charging cradle indicates the REDMIKE is charging A green light indicates that charging is complete and a full charge has been reached A blinking light indicates a charging or sensing error See Troubleshooting section for more information REDMIKE incorporates alkaline protection into the microphone design Always use a Lightspeed rechargeable sensing battery Replacement AA NiMH batteries may only be purchased through Lightspeed Technologies part BA NH2A27 Do not attempt to charge alkaline batteries They can overheat and expand creating a significant hazard and damaging the microphone this is not covered by warranty 1 Plug power cord into the cradle charger and then plug the AC end into an electrical outlet 2 Ensure that the REDMIKE is turned OFF 3 Place the REDMIKE into the cradle The LED on the cradle will glow RED indicating charging has started When the REDMIKE is fully charged the LED on the cradle charger will change to GREEN ti W t f Optiona 4 Troubleshooting 5 Warranty satety Accessories amp Specifications 2 Setup amp Use 1 Overview 17 18 4 Troubleshoot 2 Setup amp Use verview 5 OPERATING THE REDMIKE Once the REDMIKE is charged follow these steps t
17. idental or consequential damages Repair by other than Lightspeed or its authorized service agencies will void this guarantee Information on authorized service agencies is available from Lightspeed Technologies Inc Our Service Department 800 732 8999 5 a m 5 p m PST will handle all your repair replacement needs IMPORTANT SAFETY INSTRUCTIONS gv f ow om Read these instructions 11 Keep these instructions Heed all warnings Follow all instructions Do not use the apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions 13 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 12 14 15 16 Only use attachments accessories specified by the manufacturer Use only with a ca
18. ill be RED indicating a signal is being received e Confirm that REDMIKE is turned on There will be a BLUE LED on the microphone to indicate it is powered on Confirm that the amplifier is turned on and the volume levels are partially turned up If you review these instructions and still have questions write down the serial number and model number of your system and call Lightspeed Technical Services at 800 732 8999 5 a m 5 p m PST TIPS TO OBTAIN OPTIMUM AUDIO PERFORMANCE Speak in a natural voice A normal conversational speech level will provide an adequate signal It is not necessary to increase the intensity of your voice the audio system provides adequate amplification approximately 5 10 dB above ambient room noises e Avoid wearing jewelry that may rub or bump against the microphone Turn the REDMIKE off during private conversations with a student parent or other classroom visitor You can also cover the LED lens on top of the REDMIKE to block the signal Recharge batteries each night When recharged nightly operating time actual usage for the transmitters will last through a typical school day 5 Warranty Safety amp Specifications 4 Troubleshooting 2 Setup amp Use Overview 1 3 Optional Accessories 31 32 5 Warranty Safety amp Specifications 4 Troubleshooting 2 Setup amp Use 1 Overview SECTION 5
19. io signal to be played through the system 4 CHANNEL SELECT SWITCH CH A B Located in the battery compartment this switch is set to Channel B at the factory 5 CHARGER INPUT Plug the charging cable from the REDMIKE cradle charger or into this jack 25 26 5 Warranty Safet 3 Optional Accessories 4 Troubleshooting 2 Setup amp Use Overview 1 REDMIKE Share Charging 1 Ensure that the REDMIKE Share is 3 Plug the other end into the turned OFF charging jack on the rear of the 2 Make sure the cradle charger i is plugged into a wall outlet 4 The LED on the microphone will Connect one end of the charging glow RED to indicate charging cable into the jack labeled CHARGER on the bottom of the abe add thig REDMIKE ME plugged in overnight 8 10 hours REDMIKE Share to obtain a full charge c MD NOTE If the system was purchased without a REDMIKE or REDMIKE VC the REDMIKE Share will utilize the BC TXLT wall charger Plug the wall charger into an AC outlet and plug the other end s into the CHARGER jack on the REDMIKE Share REDMIKE Share Initial Set up 1 Ensure the CAT 805iX is ON The blue LED on the power button will glow 2 Turn on the REDMIKE Share by sliding the switch to the top position 3 Grip the barrel in the center section Avoid covering the infrared emitters just below the microphone grille This could interrupt signal transmission
20. o set it up for use 1 Turn the CAT 805 power on The blue LED will glow 2 Remove the REDMIKE from the charging cradle and turn it on 3 Slip the REDMIKE with lanyard around the neck and position the top of the microphone just below the collarbone NOTE Positioning of the REDMIKE is critical for proper volume adjustment 4 Setthe volume on the existing amplifier at a normal level 25 3096 to start with 5 While speaking in a normal voice slowly increase the volume of the corresponding channel on the CAT 805iX until your voice is barely audible Each REDMIKE has its channel pre set to either A or B as indicated on the back of the Mic REMEMBER This equipment supplements the user s voice so they are able to speak in a conversational tone Having the volume set too high will result in feedback and listener fatigue 6 Adjust the corresponding volume on the amplifier as needed to achieve an appropriate level amplified through the speakers 7 Once initial volume level is set walk around the room and listen for audio dropout and overall audio quality Fine tuning the audio is accomplished by making minor adjustments to the volume levels on the CAT 805iX and or the amplifier 8 If a second REDMIKE was purchased repeat steps 2 4 USING REDMIKE TO AMPLIFY EXTERNAL AUDIO EQUIPMENT The REDMIKE includes a 3 5mm audio input jack to connect to an audio source like a laptop or MP3 player The REDMIKE will t
21. ransmit the audio signal to be played through the system If your system includes two REDMIKEs we recommend using Channel B student mike to amplify the external audio equipment so the teacher s volume on the Channel A teacher mike does not have to be adjusted To determine which REDMIKE is set to Channel B you can look at the switch on the back of the mike or speak into one of the mics and watch which set of LED s glow on the front panel of the CAT 805iX A Volume or B Volume correspond to Channels A or B 1 Plug your external audio equipment for example laptop into the input on the REDMIKE labeled INPUT using a 3 5mm patch cable AUDIO AA INPUT 2 Adjust the volume on the CAT 805iX receiver which corresponds to selected mic channel A or B 5 Warranty Safety amp Specifications 2 Setup amp Use Optional 4 Troubleshooting Accessories 1 Overview 19 20 3 Optional 2 Setup amp Use 1 Overview Accessories SECTION 3 OPTIONAL ACCESSORIES OPTIONAL REDMIKE VC Volume Control Controls and Connections 1 POWER LOW BATTERY POWER MUTE BUTTON INDICATOR A BLUE light indicates the REDMIKE VC is on and fully charged A RED light indicates a charge is needed BATTERY COMPARTMENT To open slide the door downward The battery should only be replaced by a Lightspeed AA rechargeable sensing battery part BA NH2A27
22. rt stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lighting storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped When the mains plug or appliance coupler used as the disconnect device it shall remain readily operable Please keep the unit in a good ventilation environment 5 Warranty Safety amp Specifications fe E o a s 2 Setup amp Use 1 Overview 33 5 Warranty Safety amp Specifications 4 Troubleshooting 3 Optional Accessories 2 Setup amp Use Overview 1 34 SAFETY WARNINGS AND CERTIFICATIONS JN CAUTION TO RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL UTION REDUCE THE RISK OF ELECTRIC SHOCK B CERTIFICATIONS This product conforms with the essential requirements of the following European Union Directives 89 336 EE
23. s 3C CONNECT CAT 805iX TO AN AMPLIFIER 1 Ensure the power is turned OFF and the microphone volume controls are turned all the way down 2 Determine whether you wish to connect to the mixed output or the individual microphone outputs CH A CH B a MIXED OUTPUT Recommended for most applications connect to this output if you wish to connect the mixed signal of micro phone A and microphone B into a single input on the amplifier CH A CH B OUTPUTS connect to these outputs if you wish to use the amplifier to control each microphone channel individually 3 Insert the stripped wires into the marked openings on the euro block connector a Unbalanced cable connection included cable connect the signal wire to the positive connection and the shield to the ground b Balanced cable connection not included this connector is recommended for long cable runs of 12 feet or more Connect the positive and negative signal wires to the marked terminals and the shield to the ground terminal 4 Secure the inserted wires by tightening the retaining screws 5 Insert the 4 connector or other appropriate connector type into an input on the existing amplifier 4 CHARGING THE REDMIKE Before use the REDMIKE should be charged It will take 8 9 hours for the REDMIKE to obtain a full charge A fully charged REDMIKE will last for over 7 hours of use If microphones are us
24. unted to a suspended ceiling grid or secured to a wall solid vertical surface Suspended Ceiling Mount 1 Attach the bracket to the ceiling tile grid t bar a Slide the tabs onto the outsides of the t bar starting with one corner b Attach the second tab around the other side of the t bar c Repeat with the other side of the bracket so it is connected at all four points 2 Slide the ISR onto the bracket until it clicks into place a Guide the mounting rails onto the bracket oriented as pictured b Once secure the ISR locks into place c To remove the ISR press the release bar down and slide the ISR off the bracket We need to label the release bar on the ISR Image that shows clip guide 3 Uncoil the Cat 5 sensor cable Connect one end of the cable to the ISR Secure wire overhead and route it back to the system 4 Connect the other end of the Cat 5 sensor cable into the SENSOR INPUT jack on the CAT 805iX preamp clip connects to t bar on ceiling t 5 Wa t fe 3 Optiona 4 Troubleshooting 5 Warranty satety amp Specifications 2 Setup amp Use 1 Overview Accessories 13 2 IR SENSOR RECEIVER ISR INSTALLATION CONT D Wall Solid Ceiling Mount 1 Screw the bracket to a place b Once secure the ISR locks high on the wall or in the middle into place of the solid ceiling Mount the bracket horizontally as shown below c
25. urce does not have a volume control such as many DVD players adjust the volume at the iRMC C If the first two options do not give optimum volume level the last place to adjust the volume is the CH B Volume on the CAT 805iX OPTIONAL IR MEDIA CONNECTOR AUDIO INTEGRATION The iRMC is designed to integrate with the CAT 805iX and multiple audio sources allowing other instructional technologies to be clearly heard throughout the classroom ISR Sensor Video Out DVD VCR Audio Out CAT 805iX OTHER OPTIONAL ACCESSORIES IRMC Infrared Media Connector MC TK250M Noise canceling headset microphone AC TCC7 Charging cable for REDMIKE Share and LT71 3 Optional A 5 Warranty Safety Accessories 4 Troubleshooting amp Specifications 2 Setup amp Use 1 Overview 29 4 Troubleshooting 2 Setup amp Use 1 Overview 30 SECTION 4 TROUBLESHOOTING COMMON PROBLEMS AND SOLUTIONS Note Most problems are directly related to low battery power Please run through the Battery Check items first For remaining troubleshooting use known good fully charged batteries ALL PROBLEMS Most Problems are related to low battery power SOLUTION Battery Check e Confirm batteries are charged each night e Confirm proper batteries are used The REDMIKE requires the Lightspeed BA NH2A27 rechargeable sensing battery for proper charging The
Download Pdf Manuals
Related Search