USER'S MANUAL
Contents
1. CE FE 192. where N is the Input number and X GPI 2 OFF will disable input 2 so the unit will is the state ON OFF not respond if this input triggers OUTPUTS To set enable the outputs white and blue wire SETGPONL Sets the outputs N for Latch SETGPO 1 L Will set output 1 for Latch SETGPO 1 L Will set output 1 for Latch SETGPONP Sets the output N for Pulse 800ms SETGPO 1 P Will set output 1 for Pulse SETGPO 1 P Will set output 1 for Pulse SETGPONC Sets the output N for Cycle 30secs only SETGPO 1 C Will set output 1 for Cycle SETGPO 1 C Will set output 1 for Cycle 10 E gE fleetminder s Default z Command list Purpose setting Options Example Enables outputs where N is the input Default 7 Outputs available GPO 1 ON Will trigger output 1 to switch on GPO NON number setting is all outputs switched off Disables outputs where N is the input Default 7 Outputs available GPO 1 OFF Will trigger output 1 to switch on GPO N OFF number setting is all outputs switched off GEOFENCE To set and enable disable geofencing Used to set up circular Geofencing where No GEOFENCE 0 3 are Circular GEOFENCE 1 S2354 6782E34524 7890 X is the number for the circular geofence geofences GEOFENCE 5 9 are Rectngular Home 250 This will set The Geofence 1 to the GEOFENCE X from 0 3 SXXXX XXXX and set as GEOFENCE 10 29 are Point location S2354 6782 E34524 7890 with the SXXXX XXXXEXXXXX XXX EXXXXX XXXX are va
3. Geofences available GEOREVIEW 3 will respond to the primary user number with GEO3 set S3452 76282 GEOREVIEW x E45362 5638 Bank 0 P where is no radius and P is Point geofence Returns the nearest geofence to the Invoked by GEONEAR location of the asset user Used for periodic reporting of the location Default is off REPORT MMM SS where MMM is number of REPORT 2 30 will report every 2 minutes and of the Fleetminder minutes for periodic reporting SS can be 30 seconds REPORT MMM SS used for seconds REPORT 00 disables reporting SPEED KKK To notify the primary identity when the Default is off SPEED KKK where KKK is the speed in SPEED 65 will trigger when the speed of Speed limit is exceeded Kmh SPEED 00 disables Speed alerts vehicle goes over 65kmh Reports back with the features that are No default STATUS enabled on the Fleetminder Reports back additional unit parameters No default SYS including the Voltage GPS and GSM signal strength etc TOW XXX ON Enables the tow away feature default is off TOW XXX ON where XXX is the distance in TOW 100 ON will turn the Tow away feature on metres with a distance of 100 metres 12 E gE fleetminder Command list Purpose Default setting Options Example TOW X OFF Disables the tow away feature default is off TOW X OFF where X is the distance in metres TOW 0 OFF will turn the Tow away feature off VOLTS VV Sets and enables t he low
4. power LED is switched off e Other Precautions Outputs The outputs are rated at 300mA max As default the outputs are set to trigger a low ground 3 fleetminder Due to outputs being limited to current we recommend using a Relay for outputs The ouputs can be configured for a latch permanent switch circuit a pulse 800mS pulse circuit normally used for central locking circuits or cycle circuit normally used for flashing indicators NOTE Cycle will only last for 30 seconds The outputs are most commonly used for Unlocking doors Sounding horn and disabling starter motor but can be used for almost anything Inputs The inputs can be connected to almost any electronic circuit however please note that there are 2 positive triggers 12V or 24V inputs and 1 negative trigger GND input Refer to the Installation guide for more information 4 0 OPERATING REQUIREMENTS Environment Do not install Fleetminder in direct sunlight or directly under any areas exposed to direct sunlight or extreme heat Fleetminder incorporates sensitive electronics and is to be installed in the vehicles cabin only Keep the unit installed in a secure location that is to be free of dust and moisture For a stealth install it is recommended that the Fleetminder is kept away from any radio antennas or speakers as it may indicate that there is a GSM network connection present to the vehicle operator Power Fleetminder op
5. time that the input1 wire is triggered by 12V or 24V Input1 recovered Unconditional input where a label can be set occurs every time that the input1 wire is released from 12V or 24V Input2 triggered Unconditional input where a label can be set occurs every time that the input2 wire is grounded Input2 recovered Unconditional input where a label can be set occurs every time that the input2 wire is taken from ground Input3 triggered Unconditional input where a label can be set occurs every time that the input3 wire is triggered by 12V or 24V Input3 recovered Unconditional input where a label can be set occurs every time that the input3 wire is released from 12V or 24V Help Input event will send an alert message via SMS and GPRS to advise that the vehicle is in trouble This will occur when the Help button has been activated Volts Occurs when the main system voltage on the Red wire goes below the amount defined by the owner for more than 5 seconds Speed Occurs when the vehicle exceeds the speed limit as defined by the operator Geofence Occurs when the vehicle enters or leaves one of 30 areas as defined by Owner Tow Away Occurs when the vehicle is moved whilst Fleetminder Towaway feature is armed Report Occurs when the periodic report timer has lapsed 8 na fleetminder 8 0 SMS Setup unless pre set from manufacture Please make sure you have activated your SIM card before proceeding and have disabl
6. triggered etc e Vehicle Site Report This function allows the user to view the Sites that the vehicle fleet has visited on a per vehicle basis per site basis or a combination of both e Vehicle Mileage Report This function returns the user with a Mileage Report on a specific vehicle number of vehicles or all vehicles over a specified date and time range e Vehicle Stop Report This function returns the user with a Stop Report on the selected vehicle over a specified date and time range e Vehicle Trip Report This function returns the user with a Trip Report on the selected vehicle over a specified date and time range e Vehicle Over Speed Report This function returns the user with a Over speed Report on the selected vehicle over a specified date and time range e Vehicle Idle Report This function returns the user with an Idle Report on the selected vehicle over a specified date and time range 16 na fleetminder 10 0 Technical Data Fleetminder SPECIFICATIONS Physical Parameters Enclosure dimensions 113 L 68 W 30 H Weight 500g Electrical DC Supply voltage 12V OR 24V DC Tolerance voltage 9V 36V Current GPRS online 60mA Current GPRS transmission 80mA Current Peak 120mA Modem specs Frequency Range MHz Support 4 frequency 850 900 1800 1900 Channel spacing Hz 200 GPRS connectivity GPRS multi slot class 10 GPRS mobile station cla
7. voltage alert Default is off VOLTS VV where VV is the voltage in percentage 12V application 12V is 100 and 24V application 24V is 100 for use in 12V and 24V systems VOLTS 00 is off VOLTS 80 will set the low voltage warning to 80 of 12V in a 12V application 9 6V VOLTS OFF Sets the VOLTS command to disable after Default is on Turns feature off after low voltage alert has it has been triggered been triggered LOCATION command when sent alone will LOCATION report the current location GPRSOFF will turn GPRS reporting off GPRSOFF To turn GPRS mode off So only SMS NOTE After turning the GPRS mode off it mode will be enabled and no reports will Default is can only be turned on by the Tracking service be sent to the online server off provider SETAPN XXXXXXXX max Where XXXXXXXXXXX UP to 48 chars is No default SETAPN internet will set the APN to internet 48 chars the APN Access Point Name Telecommunications provider Where UUUUUUUU is the username and No default SETUSER neltronics access will set the SETUSER UUUUUUU PPPPPPPP is the password the Username as Neltronics and the password as PPPPPPPP username and password are seperated by access a space Command to enable the SMS reporting for Depends on SMSEVENTON will enable the sms reporting events from the unit So basically to be the GPRS of events Such as Goefences or input SMSEVENTON able to choose wether to have sms event connect
8. E GEOFENCE 1 HERE Home 250 This will set current location 5 9 are Rectngular GEOFENCE 10 29 The Geofence 1 to the current location with the Sera HERE NAME are Point name Home and this will be set to a radius of 250m in a geofence 250metres around the point 11 na fleetminder s Default Command list Purpose setting Options Example POINT XX To see the distance from the current Invoked by POINT XX where XX is a set point geofence POINT 13 wi report the distance between the location to a set geofence user geofence 0 29 current location and the GEOFENCE 13 GEOALLON Enables all the Geofences GEOALLOFF Disables all the Geofences Enables a particular Geofence No default GEOON X where X is the geofence number GEOON 2 will turn only Geofence 2 on oo between 0 29 GEOOFF X Disables a particular Geofence No default GEOOFF X where X is the geofence number GEOOFF 4 will turn only Geofence 4 off between 0 29 Displays summary of all the Geofences Invoked by GEOSTATUS IN will respond to primary GEOSTATUS IN hat IN inside the perimiter user number with the geofences that are inside the defined perimiter Displays summary of all the Geofences Invoked by GEOSTATUS OUT will respond to primary GEOSTATUS OUT hat are OUT outside the perimiter user number with the geofences that are outside the perimiter Displays details of Geofence X for review Invoked by 29
9. In this case the response message was received due to the LOCATION command being sent Every time that a message is sent in query to the fleetminder it will respond with the command included in the message 15 fleetminder 9 0 GPRS Online Tracking This section explains the GPRS online tracking For further information refer to the Complete Online Tracking Manual In most cases when the Fleetminder system is ordered it will automatically be subscribed to our online tracking server Our Tracking server is Web based which means it can be accessed from any computer with an internet connection For security purposes a username and password is used The unit automatically reports to the Tracking server and logs all the data for reviewing These reports can then be extracted into different formats such as pdf or printed for reference Real time Tracking is available whilst also being able to use the replay a day feature which will show the activity of a vehicle on a chosen day The Tracking server can provide a variety of different reports whilst also being able to send GPRS commands to control the inputs outputs and request further information from the unit The reports that can be viewed from the Tracking server are explained in brief e Vehicle Activity Report This function returns the user with an Activity Report on the selected vehicle over a specified date range The activities can include Ignition on off panic alert input
10. USER S MANUAL NESA nan Australia Freecall 1800 633 930 Outside Australia 61 8 9383 7833 Website www nesavision com au Email tech neltronics com au fleetminder TABLE OF CONTENTS 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 Introduction Packaging Contents Precautions Operating requirements Basic Functions Wiring diagram Theory of SMS operation SMS setup GPRS Online Tracking 10 0 Technical Data 11 0 Warranty Information 16 17 19 fleetminder 1 0 INTRODUCTION Congratulations on your purchase of Fleetminder Fleetminder is an exciting Australian designed product that enables you to personally take control of the security and tracking of your assets The Fleetminder system works independently but has Inputs and Outputs which means it can be connected to any existing alarm system for alarm notification or additional triggers The Inputs and Outputs can be configured to control a range of different features The Fleetminder has a variety of different ways of reporting an event or reporting to a command The Fleetminder is fitted with a GSM GPRS module that allows for GPRS and SMS reporting When using GPRS the Fleetminder will log data on our tracking website for easy reviewing by fleet managers or owners The Fleetminder reporting can be set to many different intervals for tracking accuracy For SMS reporting the Fleetminder can either report the co ordinates to the trackin
11. at the GPS data presented is current and indicates that the location provided is where your asset is now Alternatively if your asset was outside and then went under cover such as your vehicle being driven into a garage Then this field will display LAST In this case the location and the time of your Fleetminder the second before it went under cover is recorded Both the CURRENT and LAST messages should be considered with the UTC time given in the next line e UTC DATE TIME 080527 114236 This line contains the UTC date and time An example is 080527 114236 This reads the date as year 08 month 05 day 27 format and the time 11 hours 42 minutes and 36 seconds or 11 42 36 AM You will need to add your time difference to determine your local time e CO ORDINATES S1234 7536 E11234 5678 This line presents the latitude and is in the form dd minutes minutes eg S1234 7536 and the longitude and is in the form ddd minutes minutes eg E11234 5678 e SPEED 000 If your vehicle is stationary then this line will show 000 However if your vehicle is moving the exact speed will also be detailed 14 E gE fleetminder e UNIT STATUS 44000000 The last line 47000000 Is irrelevant for SMS reporting but will always appear as a summary It confirms the message in a ASCII format to be recognized by the tracking server It is kept in the reporting message for Status confirmation e RESPONSE CFG LOCATION This is the response to event command
12. ed the message bank service Ensure red LED indicator is on and the yellow light is either on or flashing If not then check wiring 8 1 Register your phone as the primary identity Send PIN 0000 Wait for response 8 2 Now change your PIN The factory default pin or other defined pin as with all other commands can only be changed from the primary identity To change the pin Send NEWPIN 1234 where 1234 is your new PIN Wait for response 8 3 Set secondary identity only receives events The secondary identity is used for receiving events only not controlling the device Send PH2 61423123456 where 61423123456 is the secondary contact number send PH2 without a number to turn this feature off Wait for response primary identity The Fleetminder will now respond to the secondary identity as well as the primary identity where an event has occured These events can include unconditional events such as input voltage or geofencing 8 4 Setting other parameters You can now set up your geo fences speed alert low voltage alert and other features of Fleetminder using the command list fleetminder 8 5 Command List Default i Command list Purpose setting Options Example Pin number security for the access of the PIN 0000 PIN XXXX used to change the primary PIN 1234 will check the pin number in the unit Fleetminder Also used for setting the Used to set iden
13. erates on a 12 volt or 24 volt supply only If Fleetminder has a voltage higher than the operating voltage applied then the device will fail to operate and could cause internal damage to the unit If the power supplied is below the minimum to operate the unit will send a warning if programmed to do so and may switch to backup battery power See Fleetminder specifications The built in backup power supply allows Fleetminder to continue to operate and alert you if your vehicles battery power is severed The backup battery is float charged by your vehicles electrical system GPS antenna location Fleetminder is able to determine the exact location of your vehicle by the use of the incorporated GPS receiver For the GPS to work most effectively the external GPS antenna must be located in a position with as much view of the sky as possible The GPS Antenna will generally operate through non metallic objects Some suggestions include high up under the dash and below the rear parcel shelf The black face of the 4 fog fleetminder antenna is the side which must face skyward Ensure before completing the installation that the antenna is secured firmly in place Before picking a location in your vehicle for the GPS antenna it is best to first connect the GPS antenna to the Fleetminder and apply power Shortly after powering on Fleetminder you will observe the green satellite LED on the unit turn on this means the unit is receiving GPS data If th
14. et bent or crimped Always keep Fleetminder s phone number confidential and account paid up for pre paid services Remember your Fleetminders PIN amp phone number no one else should know them For Online tracking please ensure that the SIM card is GPRS enabled for more information on this please contact your sim card service provider Outputs are NOT recommended for use to directly or indirectly immobilize an operating vehicle Immobilizing a vehicle in motion is extremely dangerous The general purpose outputs are to be used to disable the vehicle s starter motor only This device is not to be used for unauthorized monitoring or tracking Do not operate this device where mobile phones or radio transmitters are not permitted Do not operate on aircrafts Do not operate near sensitive electronics such as engine brake or air bag systems e Electrical Safety Designed to work from 12 volt or 24 volt DC only Use a 1 amp in line fuse e Explosive Atmosphere The Fleetminder uses the GSM network and it is not advisable to request tracking during refueling at blast sites or at chemical sites etc e Medical Equipment Some medical devices such as pacemakers may be inhibited by GSM signals Check with a doctor or medical equipment manufacturers for more advice on this issue e Aircraft safety When transporting this equipment by air ensure the unit is totally disabled by removing the SIM card from the SIM card slot And ensuring the Red
15. g website or can report a link for a map that can be viewed on any GPRS mobile phone Unlike other tracking products on the market Fleetminder use by SMS does not require a subscription to a base monitoring service for basic functions However in most cases we recommend that fleet managers subscribe to our web service The vehicle history is available in a range of formats online and retrievable at any time via our optional subscription service NOTE For the full features of the online tracking feature please refer the Online tracking manual 2 0 Packaging Contents Before commencing installation please make sure all components listed here are accounted for In the packaging you should have 1 x Fleetminder unit 1 x GPS antenna 1 x GSM antenna 1 x wiring harness 1 x owner s manual 1 x Help switch SIM card can be supplied on request has to be GPRS enabled for online tracking 2 E gE fleetminder 3 0 PRECAUTIONS IMPORTANT Make all wiring connections to the vehicle and antenna connections to the correct sockets BEFORE connecting the main plug to Fleetminder Refer to the step by step Installation manual It is strongly recommended that the units SIM card is first registered contains credit and is tested before installation is commenced Testing will require a valid sim service For GPRS online tracking the sim card must be GPRS enabled When installing the GPS antenna make sure that the coaxial cable does not g
16. igger GND Blue 300mA Output 3 Orange 300m lt A Output 4 Gray 300mA Output 1 Yellow Input 1 Trigger 1 2 24V White Input 3 Trigger 1 2V 24V fleetminder 7 0 Theory of SMS operation NOTE The Fleetminder system can use SMS reporting as well as GPRS reporting at the same time refer to command list for setting this event Fleetminder authenticates an incoming text message by comparing the senders details phone number to that of the primary control identity which is stored in the Fleetminder flash memory Therefore Fleetminder is only able to be controlled by its primary control identity This level of security stops someone else from gaining access to your Fleetminder and potentially your assets For event reporting such as geofencing or alarm trigger a secondary identity can also be set NOTE secondary identity cannot control the unit can only get event alerts It is even better if the phone number of Fleetminder is kept confidential along with the PIN code that you have for your Fleetminder Each Fleetminder can have its own label This label can be individually set and is usually used to identify a vehicle or asset in a fleet e Alert Events An alert event is any of the below occurrences which if configured will initiate a SMS or and GPRS response Please note all alert events need to be configured and enabled before they will work Input triggered Unconditional input where a label can be set occurs every
17. ion triggers reporting Command to disable the SMS reporting for Depends on SMSEVENTOFF will disable the sms reporting events from the unit So basically to be the GPRS of events Such as Goefences or input SMSEVENTORE able to choose wether to have sms event connection triggers reporting Command to allow users using the sms no default MAP will invoke a response from the unit that MAP function only to view their vehicle on a map will provide a URL link that can be viewed on their mobile phone using GPRS through any GPRS phone 13 na fleetminder 8 6 SMS message format explained The following information displays the format of an SMS message received from the device The Message parameters are separated by a comma and each part is explained below SMS Format Fleetminder Command Current 080527 114236 S1234 7536 E11234 5678 000 44000000 CFG LOCATION e LABEL Fleetminder The label Fleetminder can be changed to anything you like by using the LABEL command For example you may want to put your vehicles number plate details here e EVENT Command The event includes the reason that the SMS message was sent In most cases when a command has been sent to the device it will respond with COMMAND otherwise if an input trigger has occurred it will respond with the Input name such as ACC or DOOR Note Input names can be set separately refer Command list e GPS FIX Current Current indicates th
18. is does not happen place the antenna on the roof of your vehicle making sure that your vehicle is outdoors Wait until the LED comes on and stays on This now indicates Fleetminder has a fix on your vehicles location Please be patient as with a cold start first power up this process of satellite acquisition can take up to 5 minutes in worst case In some cases where the control of the Fleetminder is set to SMS as a default and the unit has started up successfully RED and GREEN lights on with the YELLOW LED flashing or still you are able to find out the GPS status by simply sending a SYS sms command from the Primary declared phone number see command list to see how to set this and for further instructions on the SYS commana In the reply message you will see the status of the GPS Minimal installation If you would like to use Fleetminder for GPS SMS tracking only then all you need to do is simply connect Fleetminder to a constant 12volt or 24 volt source and place the GPS antenna in a suitable location The Fleetminder system should be installed at least 60cm 2 feet away from your vehicles wiring and electrical systems to prevent interference The GSM signal strength can be identified by using the SYS sms command sent from your primary controlling phone number refer to the command list fleetminder 5 0 Basic Functions FUNCTIONS APPLICATIONS GPS GPS receiver will output a complete position velocity a
19. lid Coordinates default name Home and this will be set to a radius of X NAME DISTANCE NAME is the name of the geofence 250m in a geofence 250metres around the Distance is the distance around the point geofence in meters Used to set up rectangular Geofencing X No GEOFENCE 0 3 are Circular GEOFENCE GEOFENCE 5 S2354 67822E34524 7890 GEOFENCE X is the number for the rectangular geofence geofences 5 9 are Rectngular GEOFENCE 10 29 S2355 67830E34530 7826 Worksite This will 1111 1114E11111 1111 from 5 9 S1111 1111 and set as are Point set The Geofence 5 to point1 N 52222 2222E22222 2222 E11111 1111 are valid pointi Coordinates default 2354 67822E34524 7890 and point 2 NAME 2222 2222 and E22222 2222 are valid S2355 67830E34530 7826 with the name point2 Coordinates NAME is the name of Worksite note rectangular geofences do not he geofence need a radius Used to set up point Geofencing X is the No GEOFENCE 0 3 are Circular GEOFENCE GEOFENCE 11 S2354 6782E34524 7890 GEOFENCE X number for the point geofence from 10 geofences 5 9 are Rectngular GEOFENCE 10 29 Office This will set The Geofence 11 to the SXXXX XXXXXEXXXXX XX 29 SXXXX XXXX and EXXXXX XXXX set as are Point location S2354 6782E34524 7890 with the XX NAME are valid Coordinates NAME is the name default name Office note point geofences do not need of the geofence a radius Used to set a radius geofence to the No default GEOFENCE 0 3 are Circular GEOFENC
20. nd time PVT solution in the NMEA Version 3 0 protocol GPRS uses standard TCP or UDP communication protocol SMS can GPRS SMS be turned on or off 3 controllable inputs 5 inputs INPUT1 positive trigger most common applications include ACC Alarm trigger INPUT2 negative trigger INPUTS positive trigger 2 reserved inputs and door trigger Help switch trigger Temperature switch port 7 outputs Gray wire 300mA usually used for flashing lights disabling starter motor and unlocking doors 2 Green wire 300mA 3 Blue wire 300mA 4 Orange wire 300mA 5 Purple wire 300mA 6 White Red wire 300mA 7 Brown Yellow 300mA Will send a report when the Help switch has been activated Help Switch Standard Reporting Automatic report for tracking purpose Fixed time report Fixed distance report Event Report SMS and GPRS Temperature report Speeding report Low battery report Geo fence trigger report Input trigger report e g ALARM ARM ACC inputs etc fully customizable History data store hardware 900 reports can be saved in unit and read by the server at any time 6 fleetminder 6 0 Wiring Diagram Green LED GPS Indicator Yellow LED GSM GPRS Indicator Red LED Power Indicator e Panic switch 1A Fuse BrownsYellow 300mA Output 7 White Red 300mA Output 6 Purple 300mA Output 5 Green 300mA Output 2 Brown Input 2 Tr
21. ss B SIM card interface 3 4 4 5V SMS storage Capacity 40 in ME Antenna Connector Silver Male TNC or SMA Antenna Impedance 50ohms GPS specs Channels 20 parallel tracking Correlators Frequency 200 000 plus L1 1575 MHz Position accuracy Horizontal lt 2 5m CEP autonomous lt 2 0m CEP SBAX fleetminder Time to first fix Standard GPS software Hot start 1 lt 1s Warm start 2 lt 32s Cold 3 lt 35s NMEA message switchable GGA GSA GSV VTG RMC GLL Fleetminder Communication GPRS SMS Environmental Operating Temperature 20 C to 55 C Storage Temperature 40 C to 85 C 18 fleetminder 11 0 Warranty The Fleetminder is guaranteed for a period of twelve months from date of purchase against defects in materials and workmanship under conditions of normal use To obtain warranty support return the unit together with proof of purchase to the place of purchase e Limitations of Warranty Fleetminder accepts no responsibility for any actions of the purchaser or user of the equipment where the equipment is not used for its intended purpose and isn t installed in accordance with the instructions provided in this manual Fleetminder does not accept responsibility of any consequential effects or breaches resulting from the use of this equipment in a manner which constitutes a criminal act or breach of privacy
22. tity as long as the PIN number is correct and if void will ignore the message but if PIN XXXX primary identity the primary correct it will change the primary identity to the identity phone number where the message was sent from Used to change the pin number from the No default NEWPIN XXXX where XXXX is the new 4 NEWPIN 1234 will change the pin number from NEWPIN default setting digit pin number the unit as long as the message is sent from the primary identity LABEL NOTE For online Sets the label for a unit This can be set as No default LABEL XXXXXXXXXXX where the LABEL Ferrari will set the label of the unit as tracking the Label will be a Rego plate Maximum 11 characters XXXXXXXXXXX is the new label max Ferrari The label can be number or letter pre set and provided This 16characters format lowercase and upercase is not to be changed as it will affect the tracking server Authentication Sets the secondary number for event No default PH2 XX where XX is the secondary phone PH2 0412345678 will set the secondary PH2 XX reporting number note PH2 without the number will number to 0412345678 disable this feature INPUTS To set input parameters brown and orange wire Renames the label heading for an input Up to 16 characters for all 3 inputs LABELIN LABELIN 1 Starter will set the label of input 1 LABELIN N X N X where N is the number of the input 1 3 to Starter and X is the input name GPIN X Enables or disables an input GPI N X
Download Pdf Manuals
Related Search