KGNCMAVAA USER MANUAL
Contents
1. kogan KGNCMAVAA USER MANUAL kogan IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 Read all Instructions 2 Do not touch hot surfaces Use handles or knobs 3 To protect against fire electric shock and injury to persons do not immerse cord plugs in water or other liquid 4 Unplug from outlet when notin use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance 5 Do notoperate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment 6 The use of accessory attachments not recommended or sold by the appliance manufacturer may resultin fire electric shock or injury to persons 7 Do not use outdoors 8 Do notlet cord hang over edge of table or counter or touch hot surfaces 9 Do not place on or near a hot gas or electric burner or in a heated oven 10 To disconnect turn any control to off Then remove plug from wall outlet 11 Do not use appliance for other than intended use 12 Avoid contacting moving parts 13 Don t move the covering lid away when the appliance is in use 14 Scalding may occur if the brewing unit is removed during the brewing cycles SAVE THESE INSTRUCTIONS If an extensio2. LCD dreg drawer is full remove the dreg drawer and empty it Note The dreg drawer may be emptied only when the machine is switched on The dreg drawer must be removed for more than 5 seconds otherwise the warning tone will be repeated CLOSE THE DOOR Brewing door is not closed Be sure to close the DRIP TRAY MISSING TII brewing door If this message is indicated on the LCD install the drip tray or make sure it is correctly positioned NU H VENTILATE The machine needs to be cooled VENTILATE PRESS OK BUTTON DREG DRAWER MISSING O Dreg drawer is not in the right position Please check SA NJ if the dreg drawer is correctly installed EX DECALCIFY t When LCD shows DECALCIFY that means the machine needs to be descaled A e DECADE IY Press ESC to cancel decalcify The warning will be repeated next time PRESS OK ORESC Press OK to continue OK ESC BREWING UNIT MISSING Brewing unit is not in position please check if the 3 7 Cleaning and maintenance i Keeping the machine clean is vital to making high quality coffee and extending the service life of brewing unit is installed or if correctly i
3. er the device Touch the SE to start heating up at this point please wait Once the steam is ready turn the tiny knob on the device to milk frothing mode See Fig 2 and then the device will start frothing milk Press the steam button on the machine to stop frothing when the milk foam meets your expectation Please clean the device after use Fill fresh water into a jug immerse the pipe into it and press the steam button to start cleaning Refer Fig 3 to switch to hot water mode Refer Fig 4 to switch to steam mode Press steam button to start heating up e Turn the knob for hot water L 1 LI Press the steam button for steam Fully automatic Coffee Machine USER MANUAL 11 12 3 3 5 2 Hot Water 3 4 2 Adjust coffee grind thickness Steam Hot water pipe is separated from coffee spout Hot water can be used for making tea Grinding grade need to be adjusted if either the coffee flows out too fast coffee granules are too instant soup and so on big or too slow coffee granules are too small Place a cup under the pipe and then refer to Fig 2 to switch to hot water mode Touch a A The adjustment can only be made during grinding to start producing hot water The temperature of hot water can be adjusted by touching or otherwise the machine will be damaged during
4. machine Don t use the machine for any other purpose A Do not touch the hot Please operate only as shown in the manual water and steam exhaust Warning This machine should only be operated by adults who have read and understood the manual Never touch the machine with the electrical objects as they can cause injury or death Plug the machine into a suitable electrical socket The voltage must correspond to the voltage on the rating plate Do not use the machine outdoors Avoid touching moving parts Lids of containers brewing unit Don t shake the machine when it is in working Scalding may occur if the protective parts of the machine such as covering lids funnel cover brewing door are removed during the brewing cycles 2 1 1 Power cord Never use the coffee machine if the cord is damaged If the power cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Do not pass the cable around corners over sharp edges or over hot surfaces and keep it away from oil Do not use the cable to carry or pull the machine Do not remove the plug by tugging on the cable and do not touch it with wet hands Make sure the cable cannot drop freely from tables or shelves Children are unaware of the danger that electrical machines represent therefore children should never be left unsupervised with the machine USER MANUAL 03 04 2 1 2 Keep childre
5. of coffee liquid Both of the two adjustments will automatically be saved 3 3 2 Stop coffee brewing Touch ESC key to terminate the coffee making process uopnq JOY 5 0008 40ML q ESC 3 3 3 Making coffee with coffee beans There are two methods to make coffee with the machine Either coffee bean or coffee powder can be used In order to keep the freshness of the beans the appropriate amount of beans will be grinded to brew a cup of coffee 3 3 4 Making coffee with coffee powder Touch the add powder button 4 oh n Open the funnel cover 9 when fill powder icon appears the screen fill a flat spoon of coffee powder into the funnel then touch either Single dll Shot or Double Shot button to start making coffee ml Oe Touch the add powder button 0000 40ML HE m ESC One flat spoon wW ESC eo Add appropriate amount e Choose single shot of coffee powder or double shot A The appropriate amount of coffee powder going to the funnel should be no more than one flat spoon 3 3 5 Milk Frothing Device 3 3 5 1 Frothing milk Fill milk into a milk jug then pull the pipe out from the slot and immerse it into the jug Place a mu
6. ations 1 5 Accessories of the machine 2 1 Safety 2 1 1 Power line 3 How to use the machine te eee 3 1 Install the machine U 3 2 Discharge water 3 3 Operation 3 3 1 Single Shot Double Shot of coffee 3 3 2 Stop coffee brewing 3 3 3 Making coffee with coffee beans 3 3 4 Making coffee with coffee powder 3 4 Suggestions 3 4 1 Pre warmcups 3 4 2 Adjust coffee grind thickness 3 4 3 Adjust the height of coffee spout 3 4 6 Water quality 3 5 Program 3 5 1 Menu 3 6 Other indicators 3 7 Cleaning and maintenance 3 7 2 Cleaning the water tank filter 3 7 3 Storage 4 Troubleshooting 3 4 7 Working time VEU 1 Coffee machine introducton 1 1 Machine components See fig 1 above 1 2 Control panel See fig 2 above 1 3 Safety features of the coffee machine 1 3 1 Excessive powder protection If the user adds excessive powder the machine will stop brewing after 2 seconds Unnecessary powder will be discharged then machine will resume making coffee Adjust powder quantity For additional adjustments to coffee powder quantity use the following instructions Check the machine before adjusting First choose the coffee grind thickness level Check if there is coffee powder overflowing from the brewing unit or there is too much coffee powder in dreg plate Adjust powder quantity to the maximum if there is still too little coffee powder in brewing unit the coffee powder
7. d noises and the coffee machine will shut off automatically after 20 seconds If the grinder is blocked by stone or sand never try to take out the impurity yourself please contact an authorized 1 4 Specification parameters Rated voltage L 220 240V AC 50 60Hz Rated power L 1250 1450w Size L W H 415 x 320 x 365mm Net weight Dreg cake Exterior power cord Temperature control Digital control Coffee powder quantity program adjust Coffee powder thickness Manually adjusted 3 settings Water tank capacity Coffee bean tank capacity Steam hot water exhaust range 60 70 Coffee spout height range Overheat protection Dual protection temperature fuse and temperature sensor Pump pressure Compliance with EN bylaw EN 60335 1 EN 60335 2 14 EN 60335 2 15 EN 62233 1 5 Accessories included with the machine Fully automatic Coffee Machine 2 Read before starting the coffee machine 2 1 Safety A Danger The machine is an electrical appliance there is risk of short circuit and electric shock if it comes in contact with water Steam and hot water can scald users never aim hot water or steam at yourself or others Avoid touching steam and hot water exhaust directly with your hands Do not make any technical changes of the machine Unplug from outlet when not in use and before UJE9 S JO J9 8 M JOH cleaning Allow to cool before putting on or taking off parts and before cleaning the
8. es heating Press to set whether the machine COFFEE TEMP DESCALING DESCALING controller and other important components stay in good TIMER 30MIN automatically goes to energy saving mode TIMER 30MIN working condition ee after a certain period of time WATER HARDNESS According to the water hardness coefficient decalcification ABOUT PRODUCT TONES SETTING should be taken every 3 or 4 months Decalcification has to FACTORY SETTING ABOVTER ODUCT be taken as soon as the reminding message decalcify FACTORY SETTING 3 3 T OK z O ESC appears the screen Please press to start x OK O ESC decalcification Refer to following steps o Take out the water tank and clean it then fill more than 1 litre of fresh water into the water tank Press OK button FILL SOLUTION LCD shows TO TANK The machine will be back to standby PRESS OK BUTTON mode after rinsing OK Choose DESCALING A Never descale with vinegar 1 Choose the 127718 168 program display will show M 4 PRESS OK BUTTON Fill fresh water to clean the machine Press OK If the descaling is interrupted by switching off the machine it will automatically resume when the machine is switch back on e Fill water into water tank and add the Decalcify substance Importance of decalcification Seasonal decalcification can save expensive mainte
9. g Put coffee beans into bean tank Take out water tank andfill fresh water to 3 4 capacity A 3 2 3 3 Caution Fully automatic Coffee Machine USER MANUAL 07 08 Use pure water only Do not fill liquid other than water into the water tank In order to extend service life of the coffee machine do not mix coffee bean with other material such as sugar and so on otherwise the grinder will be damaged These damages are not in the scope of warranty Discharge water Turn the steam hot water exhaust towards the drip tray place a cup under it and then touch the OK button by following the instructions on the screen The machine will then start to pump water out Caution The drainage procedure should be carried out in the following four cases The initial use of the machine After the water tank was completely emptied The machine has not been use for a long period of time Upon completion of the use of steam Operation 3 3 1 Single Shot Double Shot of coffee Touch the single shot button 3 or double shot button E to start making one shot or two shots of coffee The following adjustments can be made Powder quantity Press or during grinding process in order to adjust the quantity of coffee powder Coffee quantity Press or when coffee is following out from the spout in order to adjust the quantity
10. kwise take off the filter and clean it If you do not plan to use the machine for a long period turn it off and pull out the plug Store the machine in a dry place and keep away from children Keep the machine clean Check the machine regularly and clean it according to the instruction manual 4 Troubleshooting Switch power off then pull plug out immediately when the machine has been damaged in any manner When malfunction occurs try to find solutions for the manner by referring to the table below Do not try to fix the machine by yourself in order to avoid getting injured return machine to the nearest authorized service facility for examination repair or adjustment if needed Otherwise Problem Possible Reason orindication Possible Fix Grinder sounds unusual Coffee does not flow There are some external items in the grinder Grinding coefficientis excessively high Contact factory or authorised dealer Adjust grinder level Brewing unit can not be moved No water or steam Brewing unit is not in original position The steam hot water nozzle is blocked Close the brewing door restart the machine brewing unit will return in original position Dredge the nozzle with needle A To avoid scalding make sure the machine has been turned off
11. n away from the machine Never allow child to play with the machine gt N Never use a damaged A Keep the cable away from power cord fire and hot surfaces po 24 M g amp X Never squeeze the power cord Keep the machine away from fire and high temperatures 2 1 3 Placement of machine Place the machine on a flat and horizontal surface and make sure it is inaccessible for children or pets to avoid harm The most appropriate temperature for operating the machine is between 2 2 Connect the supply cord The coffee machine must be connected to an AC outlet Make sure the actual voltage 10 C to 35 C Do not place the machine near hot surfaces or fire matches the rating voltage label on bottom of an the machine Never use a damaged cord or plug N Plug into an AC outlet Place the machine on a level and J F clean surface Leave at least 100 mm between the wall and the machine RQ gt Warning Electric current can cause death Handle with care at all times Do not immerse plugs in water or other liquid 2 1 4 Cleaning Before cleaning make sure that all switches have been turned off and unplug the coffee 3 How to operate the machine 3 1 Install the machine A Never start the machine if it does not contain water or coffee beans o Put drip tray into the groove located in lower par
12. n cord is used 1 the marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord 3 the longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped Over This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops offices and other work environments farm houses by clients in hotels motels and other residential type environments bed and breakfast type environments Fully automatic Coffee Machine USER MANUAL i EI Machine components Fig 1 7 Drip tray 2 Power cord 9 Milk Frothing Device Steam hot water pipe Coffee spout 4 9 Cup warming plate Display Water tank Powder cover Powder funnel Hot water 3 Adjusting knob Died diswer 3 Coffee bean tank Brewing door Brewing unit Dreg plate Fig 2 Control panel db op 1 Double Shot Steam __ ___ Single Shot e Menu Power Add powder y 1 3 2 Impurity filter 1 4 Specific
13. nance costs lfthe decalcification is not complete or done correctly the manufacturer will not be responsible for any damage caused decalcify substance into the water tank Press OK to start descaling The LCD shows H ENGLISH COFFEE TEMP DESCALING KGNMCAVAA TIMER 30MIN DATE 2010 09 01 WATER HARDNESS gt TOTAL COF 00000 ONES SETTING VERSION 710 01 Fill the water tank with water and some decalcify substance Press OK button ABOUT PRODUCT FACTORY SETTING OK ESC ESC ABOUT PRODUCT After about 60 minutes the water tank Press key to view the product information will be empty and the LCD will show FILL FRESH WATER PRESS OK BUTTON FILL FRESH WATER OU FACTORY SETTING oti rie Press to restore the factory settings TIMER 30MIN WATER HARDNESS TONES SETTING ABOUT PRODUCT OK O ESC PRESS OK BUTTON Descaling finished 3 6 Other indicators FILL WATER If this message is shown on the LCD there is either no water in the water tank or it is not installed properly Add fresh water and make sure it is set in the correct position ADD BEANS If this message is displayed on the LCD add beans in the coffee bean container DREG DRAW FULL If this message is displayed on the
14. nstalled the machine Never put the machine into water or other liquids in order to avoid causing short circuit Shut off the power before cleaning and wait for the machine to be cool N Never put the parts of the machine into a dishwasher O Never put components into microwave oven or over dries 3 7 1 Cleaning the main components In order to keep the coffee spout and the brewing unit clean it is recommended to empty the dreg drawer and drip tray once a day Clean the water tank drip tray drip tray cover and dreg plate regularly When the red buoyage in drip tray is higher than drip tray surface please empty the drip tray as soon as possible 1 Turn off the power pull out the plug then open the brewing door 2 Lift the handle on the brewing unit and push the press lever Take out the brewing unit Clean the main equipment with hot water without detergent Take out dreg plate and dreg drawer Clean them 1 Turn off the power and open brewing door Take out the brewing unit correctly and clean it Take out the dreg drawer and the dreg plate oro RP gt Clean the area around brewing unit competely And then install dreg drawer again Clean the area around brewing unit Take out brewing unit with handle Slide into the initial po
15. quantity needs to be increased Adjust method Active when coffee making is finished before the LCD display shows ready for use press MENU key see FIG 3 and hold until LCD shows FIG 4 then press OK key to enter the coffee powder quantity adjustment option see FIG 5 in this mode press key to reduce coffee powder quantity up to 9G press key to increase coffee powder quantity up to 96 after adjustment press OK key to save and return to normal working condition If you do not want to adjust then press ESC key to exit Passive when making coffee if there is too much coffee powder in brewing unit causing the coffee powder to overflow then the LCD would show FIG 5 in this mode press key to reduce coffee powder quantity up to 9G press key to increase coffee powder quantity up to 9G after adjustment press OK key to save and return to normal working condition if you do not want to adjust then press ESC key to exit 0606900 CALIBRATION CALIBRATION 40ML Sd OG OG OK ESC OK ESC FIG 4 FIG 5 Fully automatic Coffee Machine USER MANUAL 01 02 1 3 2 Impurity filter The impurity filter in the grinder keeps unwanted sand and stones that may be contained in the coffee beans away These impurities may otherwise cause damage to the machine If some impurities still find their way into the grinder they will cause the grinder to make unusually lou
16. sition Be sure the brewing unit is well positioned after hearing click sound then install the dreg drawer Close the brewing door finally Put back brewing unit Note When inserting the brewing unit never push the press lever It will cause damage to the machine Warning If the brewing unit is not correctly inserted BREWING UNIT MISSING will be displayed Usually the bean tank is not required to be clean Clean it with cotton if needed Note Never add water into bean tank otherwise it will cause damage to machine Clean the milk frothing device Remove the metal tube Clean the metal tube and nozzle with water If the nozzle was blocked clean if with pin wash it with water Re assemble after cleaning A 9 Clean metal tube and nozzle to keep the spout expedite Warning Make sure the machine is switched off and the steam hot water pipe has cooled down completely Fully automatic Coffee Machine USER MANUAL 23 24 3 7 2 Cleaning the water tank filter Remove the water tank There is an inlet which connects with water tank Turn the cover anticlockwise take out the filter in it and clean it Reassemble after cleaning The water inlet is located under the water tank XU J9 em ay 3 7 3 e Turn the cover anticloc
17. t of the machine Then wait until the machine is cool before cleaning it Never put the machine under water 2 1 5 Repair and maintenance Unplug the machine immediately if it falls down Do not operate the machine with a damaged cord or plug or has been damaged in any manner Manufacturer will not assume machine Make sure the drip tray cover is correctly responsibility for damage caused by unauthorised repair positioned A Use carbon dioxide extinguisher in case of fire Never use water or dry powder extinguisher Install the drip tray Do not immerse the machine in water or other liquid Use carbon dioxide extinguisher 2 Remove coffee bean tank cover and put the proper quantity of coffee beans no more than 200g into the container e Remove the water tank from the machine and fill it with fresh water to 3 4 capacity The valve in bottom of the water tank is for water discharging Gently press down the water tank then cover the lid to replacement Untie the power cord then connect to power supply touch the symbol press the power icon on the Display The screen shows self test first and then warming up Disappearance of the tiny dots represents the boiler temperature reaches a higher level The machine will start rinsing after the boiler reaches appropriate temperature Please wait until a beep and the screen shows standby the machine has finished preparin
18. this period there are three levels available The maximum production of hot water is The recommended grade is 2 250ML Turn the powder thickness adjust knob to a lower number if the coffee granules are too big turn the powder thickness adjust knob to a higher number if the coffee granules are too small The recommended grade is 2 y 3 4 3 Adjust the height of the coffee spout Move the coffee spout up and down to make the spout a little higher than the cup so as to keep the aroma of the coffee steam hot water pipe 4 water position 1 Place a cup under the Turn the knob to hot Adjust height of coffee spout 3 4 4 Pre brewing coffee The pump will stop for 2 second after the coffee powder has been wet then continue e e 3 4 5 Coffee bean storage O ESC To make sure that the coffee beans or coffee powder is fresh put coffee beans into a sealed d container then put the container in a cool dark place Press the hot water button Press OR button 3 4 6 Water quality Besides the coffee beans grinding and water temperature water quality is also important We 3 4 Suggestions lt suggest treating the water with a water filter or purifier before putting it in the coffee machine 3 4 1 Pre warm cups The water in the water tank m
19. ust be changed daily 3 4 7 Work time The machine can work continuously all day Place cups above the cup warming plate to warm them up 3 4 8 Turning off the power Please wait until the machine is in standby mode before turning off the power Suggest to pre warm Fully automatic Coffee Machine USER MANUAL 13 14 3 5 Program 3 5 1 Menu Press the Menu button then choose from the following options N D gm WATER HARDNESS ENGLISH LANGUAGE COFFEE TEMP Press MENU to choose water hardness COFFEE TEMP OK DESCALING DESCALING Press to access language menu then IEMER 30MIN setting Choose hardness value press OK TIMER 30MIN choose your preferred language button to confirm WATER HARDNESS TONES SETTING TONES SETTING ABOUT PRODUCT ABOUT PRODUCT FACTORY SETTING FACTORY SETTING OK O ESC E E ENGLISH TONES SETTING TEMPERATURE OF COFFEE COFFEE TEMP OK DESCALING Press to switch button keypad warning a j ti DESSEN Press to adjust temperature of coffee TIMER 30MIN Oren TIMER 30MIN standard cup then press to confirm WATER HARDNESS WATER HARDNESS TONES SETTING TONES SETTING ABOUT PRODUCT ABOUT PRODUCT FACTORY SETTING FACTORY SETTING O ESC C ENERGY SAVING SETTING F ENSIS Decalcification COFFEE TEMP OK Decalcification is vital to ensure the valv
Download Pdf Manuals
Related Search