USER MANUAL - PAP Heating Solutions
Contents
1. 4 events in 7 days Pra 123458 Selection of type only visible in type MCD2 Type MCD2 1999 UA has a built in temperature sensor and an externally temperature sensor In this configuration the thermostat controls the temperature within the room and use the externally temperature sensor as limit sensor Type MCD2 can be changed into type MCC2 1991 UA with an external temperature sensor that normally is placed in the floor construction In this configuration the thermostat controls the temperature of the floor and not the temperature within the room MCD2 can also be changed into type MCC2 1999 UA with a built in temperature sensor In this configuration the thermostat controls the temperature of the room and the external temperature sensor should not be installed oka MCD2 1999 UA With 2 sensors built in room sensor and incl floor sensor 3m MCC2 1991 UA Incl floor sensor 3m MCC2 1999 UA With built in room sensor Max and min allowed temperature range The temperature setting range of 5 to 40 C can be limited to prevent a too high or too low temperature being selected under manual or comfort mode For MCD2 with limit sensor the max and min temperature range refer to the temperature of the limit sensor For example A wood floor covering should not be allowed to exceed a maximum of 27 C Low limitation is used where the temperature of the floor is required never to fall below the minim2. Time and temperature 4 Advanced settings and read out Press both UP A and DOWN V buttons together for 3 seconds INFO is displayed Press UP A button until you reach the desired sub menu Select the sub menu with the OK y button Monitoring of energy consumption The thermostat calculates average time it has been switched on allowing you to monitor your energy consumption In the thermostat you can read out Total switch on time in percentage in the latest 2 days 30 days or 365 days Calculation of operational costs per day switch on time 100 x kW x kWh price x 24 h per day Example Read out 30 in the latest 365 days Size of heating system 1 2 kW ask the installer Cost of power 0 2 USD kWh Calculation 30 100 x 1 2 kW x 0 2 USD kWh x 24 h 1 7 USD per day 2 days Press UP A or DOWN V button to show the different 30 days readouts 365 days No changes can be made here Use the OK V button to end Software version Actual sensor temperature 4 event sequence The present event sequence flashes Days 1 5 followed by days 6 7 To change press the UP A button until you have days 1 6 and then day 7 flashing or all 7 days are flashing Select the required sequence with the OK y button 4 events in 5 days Pr a 2 events in 2 days 4 events in 6 days 2 events in 1 day
3. USER MANUAL Type MCC2 MCD2 57583 08 06 BJ Product program This user manual covers following electronic thermostats MCC2 1991 UA Incl floor sensor 3m MCC2 1999 UA With built in room sensor MCD2 1999 UA With 2 sensors built in room sensor and incl floor sensor 3m Introduction The thermostat is capable of switching on your heating system at pre determined times on different days of the week It is possible to set 4 periods called events each day with different temperatures From factory a default schedule is programmed suitable for most installations Unless you change these settings the thermostat will operate to this default program Working with lower temperatures during times that the room is unoccupied will lower your energy costs without reducing the comfort The thermostat has an adaptive function that automatically changes the start time of a heating period so that the desired temperature is reached at the time that you set After 3 days the adaptive function has learned when the heating must be switched on Type MCC2 1991 UA has an external temperature sensor that is normally placed in the floor construction In this configuration the thermostat controls the temperature of the floor and not the temperature within the room Type MCC2 1999 UA has a built in temperature sensor In this configuration the thermostat controls the temperature of the room Type MCD2 1999 UA has a built in temperature sensor and an externally temp
4. election of type will return to a MCD2 Failure code E2 will be displayed if the external sensor has been removed Factory settings 4 event time and temperature ne Time es 55 C 5 C 06 00 08 00 16 00 08 00 23 00 Day 1 5 Day 6 7 Adaptive control ON 6 Failure codes EO Internal failure replace thermostat E1 Built in sensor short circuit or disconnected replace thermostat E2 External sensor short circuit or disconnected OJ ELECTRONICS A S Stenager 13B DK 6400 S nderborg Tel 45 73 12 13 14 Fax 45 73 12 13 13 oj oj dk www oj dk gt 7583
5. erature sensor In this configuration the thermostat controls the temperature within the room and use the externally temperature sensor as limit sensor avoiding to high or to low temperatures in the floor construction The thermostat has a pin button marked R allowing you to reset the thermostat to factory settings These are listed at the end of this manual with space for you to record your own weekly schedule The display is backlit when operating the buttons The heating element is switched off when the light is on in the display The heating system can be switched off on the built in interrupter The Microprocessor taking care of the time will still be supplied with power whereby time and day will be maintained When the heating is required and the thermostat is switched on it will continue the 4 event programme based on present time and day 1 Getting started Buttons Display symbols BR929B05 Pin button On off Reset to Adjustment Time and Day number adjust of factory down j temperature clock setting OK Adjustment Display Heating on 4 event symbol accept up Monitoring Xt Wake O Out of switch on time C Night Home Setting the thermostat into operation First time power is connected the clock and day will be flashing and must be set If you need to adjust the time of the thermostat at a later date insert a pin into the hole for setting of time and day Adjustment must be made for summer and winter time Pre
6. ss the UP A or DOWN V buttons to select the correct time and press OK button vV Then press the UP A or DOWN V button to select the correct day and press OK V button 343 123450 Type MCC2 MCD2 2 Daily use of the thermostat 4 event clock mode The day has been split into 4 events describing a typical day When the thermostat is in 4 event mode it will automatically adjust the temperature according to the required temperature to the required time As standard the thermostat has 5 days with 4 events and 2 days with 2 events Programming see 3 4 event clock mode The clock function symbol and one of the 4 event symbols AOAC will be indicated Programming see 3 Comfort mode X 5 Secs Temporary override To temporarily override the temperature in the 4 event schedule program press the UP 4 or DOWN V button once to show the temperature and press again to increase or decrease the temperature The display will flash for 5 seconds and will then revert to the time The override will operate until the next programmed event when the unit will resume the automatic programme Cancel comfort mode To cancel the override state press the OK Y button twice Manual mode w AV X 5 secs Permanent override During holidays the scheduled 4 event program can be overridden Press the OK V button and then the UP A or DOWN V button until the o
7. um set temperature Maximum allowed temperature setting Use the UP A or DOWN V button to increase or reduce and OK v button to accept Next is displayed LoLi Press OK V button to continue Minimum allowed temperature setting Use the UP A or DOWN A button to increase or reduce and OK V button to accept You can select either C or F scale and 12 or 24 hour clock as follows Press UP A or DOWN V button to change settings Confirm the required scale with the OK button v button to be continued 4 Advanced settings and read out continued Adaptive function This function enables the thermostat to calculate when it needs to switch ON so that the required temperature is reached at the set time With a start time of 07 00 therefore the thermostat may switch ON as early as 06 00 so that the desired temperature of 25 C is achieved by 07 00 Without this function set the thermostat will start to heat at the time you set Press the DOWN V button to switch between on and off Press OK V button to confirm Press OK V button to end programming and to return to scheduled programme Press the pin button and the thermostat returns to factory settings Time and day is also reset and must be set according to Setting the thermostat into operation Note that a MCD2 that has been modified to a MCC2 see 4 Advanced settings and read out s
8. verride temperature is set The unit will now operate to this temperature permanently Cancel manual mode To cancel the permanent override state press the OK V button once and the unit will resume automatic function 3 Programming Press OK V button for 3 secs to begin programmin 4 event time and temperature Vv bu gin prog Ing 37 Time and temperature For each event the start time and required temperature must be set For example in the morning you wish the heating to start at 07 00 and the temperature to rise to 25 C Press OK Y button for 3 seconds and the start time is displayed Change this to 07 00 with the UP A or DOWN V button Press OK Y to confirm The temperature is now displayed Change this to 25 C with the UP 4 or DOWN V button Press OK v button to confirm This action can now be repeated for the second event Time and temperature Time and temperature Time and temperature These settings will be valid with days 1 5 showing on the display To program the days 6 and 7 repeat the above Days 6 and 7 are usually Saturday and Sunday and only have two events The temperature can be set within the range of 5 to 40 C It is also possible to select the heating OFF at that event by reducing the setting to 5 C and then pressing the V once more 3 Time and temperature
Download Pdf Manuals
Related Search