User's Manual
Contents
1. 1 Installation and servicing should only be done by qualified service personnel or system installation personnel and conform to all local codes 2 When unpacking dome package Pan Tilt module should be handled with care not use hard thing to hit camera and other parts to avoid unnecessary trouble 3 Domes installation position must be away from high voltage as far as possible 4 Setting the dome address controlling mode and protocol appropriately before installation 1 AC24V 2 BNC Video output 3 RS485 data 4 Aluminum Die Cast Housing 5 Acylic dome 6 Camera Dome Connection Diagram A Brown Y AC24V Blue N ma p Blue RS485A Jesas data Yellow RS485B BNC Video output Dome Structure Diagram 1 Connection Instruction 1 Video output connects to matrix or monitor 2 RS485 controlling cable Blue cable connects to RS485A Yellow cable connects to RS485B 2 Dome Installation 1 Installing speed dome camera to the bracket using 4 M6 Screws 2 Installing the bracket to an existing structure Trouble Shooting Table Problem Probable causes Solution P l lug i ower supply plug in Plug tightly On Power no action no loose image Fuse on the power PCB Replace damaged Protocol setting is wrong Check the keyboard On Power self check Dome ID setting is Change the dome ID and image ok can not wrong control RS 485 Bus bad Check RS 485 connection connection2. 5 Controls Pan Tilt 16 preset positions Auto pan ON OFF Auto Tracking mode ON OFF 1 cruising tracks Power source 24 volts ac Operating temperature 30 50 Weight Approx 3 6 kg The specification is subjected to change without notice Multi protocol Operation 1 ID Setting Fi als alalstala a i 123456 789 10 ON ADD NO 6 NO 5 NO 4 NO 3 NO 2 NO 1 0 OFF OFF OFF OFF OFF OFF 1 OFF OFF OFF OFF OFF ON 2 OFF OFF OFF OFF ON OFF 63 ON ON ON ON ON ON 2 Protocol Setting Ti als alalstala a 123456 78910 ON Protocol NO 9 NO 8 NO 7 COP_02 OFF OFF OFF COP_01 OFF OFF ON PELCO P OFF ON OFF 9600 PELCO P yi OFF ON ON 4800 PELCO D ON OFF OFF 3 Operation of auto panning and auto tracking Operation Function PRESET 17 ENTER To preset NO 17 preset position means to set the start position of auto pan To preset NO 18 preset position PRESET 18 ENTER means to set the end position of auto pan To call the NO 17 preset position CALL 17 ENTER means to turn on auto tracking CALL 118 ENTER To call the NO 18 pest position means to turn on auto panning m m To call the NO 19 preset position CALL 19 ENTER means t
3. Dome2 P T Dome2HR P T HIGH RESOLUTION User s Manual Before attempting to connect or operate this product please read these instructions completely Main Features 1 Built in receiver Complete digital control with integrated CPU and SD RAM All configurable options stored in non volatile memory to protect against power cuts Integration and high durability 16 programmable presets RS485 communication data dome address 0 511 Support Auto tour and pattern 2 Pan tilt drive Innovative design of the structure minimizes the outline shape and dimensions A precision drive positioning system ensures a 0 355 pan rotation Tilt rotation range 0 90 3 Built in color camera with high sensitivity and high resolution 3 6 mm lens fitted other sizes available Auto back light compensation Auto white balance Optional keyboard control Mee Preface The 5 mini dome is an integration of the cutting edge technique most developed manufacturing process and years of full experience in the industry Equipped with high resolution camera and digital decoder it represents the trend of the new edition of surveillance product Being complete digital controlled and flexile programmable it performs an excellent fast location and continuous object tracing The simple and compact structure ensures high reliability and long term running Super features lead a wide variety of use in large area surveying and
4. Lens loose Adjust the lens again Vague Image Down cover not clean Clean down cover Intelligence Dome Camera Control Command Reference Camera Interface RS 485 Transmit Method Asynchronous Interface Half Duplex Serial Commu nication Transmit Speed 9600bps Protocol 1 Stop bit 8 bit data No Parity 1 Stop bit 2 Command Protocol Command length is fixed at 11 bytes 1 packed The packet s data arrangement is as follow Below WORDI1 STX Start of Text AOH WORD2 Receiver Address 00H 1FH WORD3 Sender Address 00H 1FH WORD4 COMMAND 1 WORDS COMMAND 2 WORD10 ETX End of Text AFH WORD11 Check Sum Calculation of the Check Sum Sum up WORD through WORD9 Deduct the above total from the FFFFH Last two digits are the Check Sum For example In case the total of WORD2 through WORD9 is 567H A00H FFFFH 567H A98H Check Sum 98H FFFFH AOOH 5FFH Check Sum FFH 3 Command Details Commands are of two types PTZ commands and extended commands The PTZ commands see 3 1 below specify manual operations while the extended commands see 3 2 below implement camera settings The command type is identified by Bit 0 of WORDS a 0 denotes a PTZ command while a 1 denotes an extended command 3 1 PTZ Command Pan Tilt Zoom The PTZ command control general manual operations PAN TILT ZOOM The PTZ commands take preced
5. direct touching down cover acid matter in the fingers will corrupt down Cover plating surface Hard material scratching down cover will lead to vague image Please use soft clean cloth or other substitution to clean interior and exterior surface Neutral detergent as well as any high grade furniture detergent can be used to clean down cover 6 Environment The operation temperature of the dome is 30 50 humidity is less than 90 input power supply is AC24V Do not use the dome in circumstances where temperature humidity or power supply variations fall outside the range of specified values 7 Excessive light It is important that the dome camera is not left in a position where the camera is pointing directly at the sun or other extremely bright light source This may result in CCD damage and poor image quality Functions and Operations These operating instructions cover the basic operation of the dome and its features When the dome is used with other manufacturers control system please regard the system controller instruction as standard In the event of special requirements outside the scope of this document it is advisable to contact your local distributor 1 Setting the dome ID Setting dome ID by the DIP Switch of the dome refer to the dome setting for the details P 6 2 Set up and call preset Preset function is that dome stores current horizontal angle and title angle of pan Tilt and position parameters into the m
6. emorizer When necessary dome calls these parameters and adjusts Pan Tilt and camera to that position Operator can store and call presets easily and promptly by using controller the dome supports up to 64 presets Toseta preset position preset N ENTER Tocalla preset position Call N ENTER 3 Auto Cruise The preset positions can be programmed to be re called in a set of sequence This sequence can be set to automatically cycle from one position to the next at a setting time This feature is called Auto cruise Cruise sequence can be programmed from 1 16 presets Start Auto cruise SHOT 1 ENTER Stop Auto cruise by moving the joystick 4 Auto Pan function The auto pan function allows you to have the camera move back and forth automatically at a preset speed between the 2 preset camera positions START AUTO Nl ON N2 OFF N1 stands for the position you want to start N2 stands for the position you want to stop STOP AUTO OFF or Move joystick the dome will be controlled by manual and the auto pan will stop Dome Setting According to the different controlling system confirm the used controlling system before operation setting ID10 is for RS485 1200 impedance When control distance is far or environment interference is severe the ID10 should be set ON when the system c
7. ence over all extended commands other than the special extended command The camera can be FOCUS IRIS stopped by setting all bits of WORD4 WORDS to 0 The contents which each word shows when Bit0 of WORDS is 0 as follow Bit7 MSB constant 0 Bit6 Not Used 0 Bit5 Not Used 0 Bit4 IRIS OPEN 90 IRIS S TOP 01 IRIS CLOSE WORD4 10 IRIS OPEN Command1 Bit3 IRIS CLOSE 11 Keep the current movement Bit2 constant 0 F TOP Bitl FOCUS NEAR Me FOCUS STO 01 FOCUS CLOSE 10 F PEN BitO LSB FOCUS FAR EDENO 11 Keep the current movement Bit7 MSB constant 0 00 ZOOM STOP Bit6 ZOOM WIDE 01 ZOOM TELE f 10 ZOOM WIDE Bit5 ZOOM TELE 11 Keep the current movement Bit4 TLT pown TET STOP WORDS 01 TILT UP Command r BiB TILT UP 10 TILT DOWN 11 Keep the current movement Bit2 PAN LEFT 0r PASTOE 01 PAN RIGHT Bitl PAN RiguT 10 FANEEPT 11 Keep the current movement BitO LSB PTZ command 0 Extension Command 1 WORD6 DATA 1 PAN MOTOR SPEED 01H 40H WORD7 DATA 2 TILT MOTOR SPEED 01H 40H WORD8 Upper 4 Bits Focus Motor speed 01H 08H DATA 3 Lower 4 Bits Zoom Motor speed 01H 08H 13 WORD9 DATAQ 4 gaal There is a bit that controls four motors rotating direction of PAN TILT ZOOM FOCUS When the bit is 1 it means that it is effective and it functions However when two o
8. f the bit that controls the opposite rotating direction are both 1 it means the current action is selected and is to be continued When two of the bit that controls the opposite rotating direction are both 0 it means the motor to be stopped 3 2 Extension command These commands are used to implement non manual settings mainly Preset Swing Sequence etc WORD4 00H WORDS5 Command No 01H to FFH Only Odd Number WORD6 DATA 1 Parameter WORD 7 DATA 2 Parameter2 WORD8 DATA 3 Parameter3 WORDS DATA 4 Parameter4 1 Set Preset WORD4 WORDS WORD6 WORD7 WORD8 WORD9 00H 03H XX FFH FFH FFH XX 00H 3FH Preset Number 2 Go to Preset WORD4 WORDS WORD6 WORD7 WORD8 WORD9 00H 07H XX FFH FFH FFH XX 00H 3FH Preset Number 3 Run Pan Swing 1 WORD4 WORDS5 WORD6 WORD7 WORD8 WORD9 00H 11H 00H Pl P2 FFH P1 00H to 3FH Preset Number First Specify Position P2 00H to 3FH Preset Number Second Specify Position 4 Stop Swing WORD4 WORDS WORD7 WORD8 WORD9 00H 1FH FFH FFH FFH 5 Run Sequence WORD4 WORDS5 WORD7 WORD8 WORD9 00H 21H 00H FFH FFH lt GG gt Sequence Number 00H 05H Technical Data Panning range 0 355 Pan speed 0 45 45 Ysec Tilt range 0 90 Tilt speed 0 45 45 Ysec Communication RS48
9. moving object tracing For instance integration building and banks securing traffic supervising power stations watching airports and stations monitoring The protocol is open and the dome is compatible with the host of systems This manual introduces dome functions and operations Please read this manual carefully prior to installation and operation Precautions 1 Transportation Domes are sophisticated products and as such should be protected against extremes of pressure temperature vibration and humidity during storage and transportation 2 Do not disassemble the Dome module There are no user serviceable parts or settings inside Failure to observe this instruction could result in damage to the product and loss of warranty Only suitably qualified and authorized personnel may undertake repairs 3 Installation This Camera is suitable for use indoors or outdoors however before using outdoors please read the information under Exposure heading at http www allthings com au Appnotes 4 Electrical safety Conform to local Electrical safety codes when use this product keep at least 50 meter between dome communication data and high voltage equipment or cables If above requirements can not be satisfied please use steel tube to shield communication Data cable and make it grounding 5 Cleaning In order to get clear image down cover should be cleaned periodically Be careful when cleaning only hold down cover edge avoid
10. o stop auto panning PRESET 201 ENTER To preset BOS preset position means to close the digital zoom 4CALL 201 ENTER To call the NO 20 preset position means to open the digital zoom Auto Tracking The Mini P T Dome can automatically track from 1 2 3 16 preset position Dwell time between 2 preset position is 4 secs Auto Panning The auto pan function allows you to have the Mini P T Dome move back and forth automatically at a preset speed between the 2 preset positions The dwell time between the start preset position and the end preset position is 3 seconds Option
11. onnects many domes ID10 of the farest dome from controller should be set ON other domes are set OFP Address Switch Switch Switch Switch Switch Switch Switch Switch Switch 9 8 7 6 5 4 3 2 1 1 OFF OFF OFF OFF OFF OFF OFF OFF ON 2 OFF OFF OFF OFF OFF OFF OFF ON OFF 3 OFF OFF OFF OFF OFF OFF OFF ON ON 4 OFF OFF OFF OFF OFF OFF ON OFF OFF 5 OFF OFF OFF OFF OFF OFF ON OFF ON 6 OFF OFF OFF OFF OFF OFF ON ON OFF 7 OFF OFF OFF OFF OFF OFF ON ON ON 8 OFF OFF OFF OFF OFF ON OFF OFF OFF 9 OFF OFF OFF OFF OFF ON OFF OFF ON 10 OFF OFF OFF OFF ON OFF 11 OFF OFF OFF OFF ON ON 12 OFF OFF OFF OFF OFF OFF 13 OFF OFF OFF OFF OFF ON ON OFF ON 14 OFF OFF OFF OFF OFF ON ON ON OFF 15 OFF OFF OFF OFF OFF ON ON ON ON 16 OFF OFF OFF OFF ON OFF OFF OFF OFF 17 OFF OFF OFF OFF ON OFF OFF OFF ON 18 OFF OFF OFF OFF ON OFF OFF ON OFF 19 OFF OFF OFF OFF ON OFF OFF ON ON 20 OFF OFF OFF OFF ON OFF ON OFF OFF 510 ON ON ON ON ON ON ON ON OFF 511 ON ON ON ON ON ON ON ON ON When there is more than one dome adopted in the system connect the controlling cable in parallel set the dome address by setting ID Switcher control the domes connected with one keyboard controller Refer to the controlling system manual for the detailed connection and operation 7 Installation Prior to installation and use of this product the following warnings should be observed
Download Pdf Manuals
Related Search