DeviregTM 535 Installation and user manual AUS
Contents
1. Min floor temperature limit Only when combination of room and floor sensor is installed 16 Changing the settings You enter the settings by pressing the pinhole with a small screw driver pencil or needle the display now changes from temperature to time display By using the arrow buttons AV you move one way or the other in the menu Setting the time By pressing the the hours start flash ing indicating you can change them with the arrow buttons AV Press the again to change the minutes Battery Backup The current time and day is kept for 80 days if mains supply is off All other settings are stored permanently Initially mains supply the thermostat for 15 hours to fully charge the battery Setting the weekday By pressing the e the weekday starts flashing indicating you can change it with the arrow buttons AV Press the to accept 17 Changing the settings Setting the timer periods When programming the starting times of the 4 periods keep in mind that the thermostat will start heating stop heat ing at the given time Therefore some periods should start and end before to compensate for the time it takes to heat up or down The first period bar L_ flashes indi cating this is the morning period By pressing the e the start time of the period starts flashing You change it with the arrow buttons AV in incre ments of 15 minutes Press the to accept The secon2. Comfort 21 C Economy 17 C Periods Day rhythm You can use the above as it is or you can change the settings to match your day pattern See the chapter Settings setting the timer periods page 18 Changing timer program To change the program Remember you need to set the time in advance p 17 Keep the e button pressed for 2 seconds The actual program starts to flash It is now possible to change the program by using the buttons AV Press to accept 14 eu lt a U Ll Changing timer program During the timer programs P2 P3 and P4 the flashing indicates the actual time period In program 4 the actual day is also shown Using the arrow buttons AV in timer mode is somewhat different from manual mode If you increase decrease the tem perature in a savings period L__ this change only applies to this current period not any future savings periods You might use this if you are eg work ing at home in timer program 4 If you increase decrease the tempera ture in a comfort period m this change applies to all future comfort periods until changed again From the perspective that you are fine tuning the comfort temperature 15 Settings overview Settings All settings are under the settings menu Here you set the following Timer periods configuration Morning day evening and night Comfort temperature Savings temperature
3. DK 7100 Vejle Phone 45 76 42 47 00 Fax 45 76 42 47 03 DEVI Heating Systems ABN 39 898 434 262 PO Box 707 Mona Vale NSW 1660 Phone 02 9997 2811 Fax 02 9997 7852 Freecall 1800 636 091 www devi com au 27
4. M both room and floor sensor The default is To change this setting press and use the arrow buttons AV to select your choice Press to accept your choice If you have selected room sensor only the installation procedure is complete Press installation button to accept Go to page 9 If you have selected floor sensor or a combination of room and floor sen sor press AV for the next setting Configuration Max floor temp Maximum floor temperature When selecting either floor sensor or Q floor and room sensors next screen is maximum floor temperature Default setting is 35 C To change this setting press and use the arrow buttons AV to select your choice Press to accept your choice If you have selected a combination of room and floor sensor the installation procedure is complete Press installation button to accept Go to page 9 If you have selected floor sensor only press AV for the next setting Notice The floor temperature is measured where the sensor is placed The temperature of the bottom of a wooden floor can be up to 10 degrees higher than the top Floor manufactures often specify the max temperature on the top surface of the floor Please contact your floor supplier for maximum surface tem perature For ceiling heating the maximum floor temperature should be set to 45 C in accordance with the plasterboard manufacturer s recommendations Configuration Scale
5. Scale If you select Devireg 535 to only use a floor sensor mode you have to select the display type The choice is either numerical scale 1 6 or Celcius scale 5 to 45 Default is Celcius scale When select ing Celcius the display will show the actual temperature at the floor sensor To change this setting press and use the arrow buttons AV to select your choice Press to accept your choice The installation procedure is now finished You can use the AV for going back or forward through the settings Otherwise Press the installation pinhole to exit installation mode 4 Put the frame and front back on User s guide to Devireg 535 Devireg 535 Introduction Devireg 535 is a simple timer temperature controller spe cially designed for floor heating systems The Devireg 535 will measure the radiant comfort from the floor or ceiling combined with the comfort from the air tem perature in the room to off set the outside weather condition This means that as soon as you have set your Devireg 535 at your desired comfort temperature Devireg 535 will then automatically adjust the heating to meet your comfort levels regardless of changing weather conditions Even the programming of economy temperatures i e lowering of temperature during the night and when you are out of the house is very simple Just tell the Devireg 535 when you want the comfort temperature and the Devire
6. the type of heating and thus which sensors should be used You have three options Comfort heating Constant temperature on the floor in bathrooms and other rooms where a comfortable warm surface is required Install the Floor sensor and choose only the Floor sensor Total heating Control of room temperature in living rooms etc Install the Floor sensor and choose both Floor sensor and Room sensor Also recommended for ceiling heating with the floor sensor located on top of the plaster board on or under the blank unheated edge of one foil Ensure that the sensor is not in direct contact with any part of the metallic heating element No floor sensor A floor sensor is not present and cannot be installed Choose Room sensor Be aware that temperature control is less accurate without the floor sensor DEVI recommends that a floor sensor is always installed Do not use Devireg 535 without a floor sensor when the heating element is installed on or beneath wooden surfaces and other surfaces sensitive to temperature Configuration sensor Selection of sensor type Power on the thermostat With the front off with a small screw driver pencil or needle press the installation button Select the sensors to be used for the heating system Devireg 535 is able to use two sensors a built in room sensor an external sensor to be placed in the floor This gives 3 options floor sensor room sensor
7. AUS Devireg 535 Installation and user manual Congratulations with your DEVI floor heating system Your property has been installed with a DEVI heating system DEVI is Europe s leading floor heating manufacturer with over 45 years experience We are confident that you will be satisfied with your new system DEVI brings you An Invisible heating solution A concealed heat source opens up greater opportunities for decorating and furnishing Optimum comfort DEVI brings you the luxury and comfort of a warm floor as well as a pleasant room temperature Floor heating is the most comfortable type of heating because it is based on the fact that warmth travels upwards pleasant warmth for your feet body and head Low running costs Thanks to the precise DEVI thermostat and the placement of the heating elements right under the floor surface the heat can be controlled optimally in order for you to have the comfort you desire with minimal energy use Moreover electric floor heating and ceiling heating is practically maintenance free in total keeping down the running costs A long lasting solution We back up our floor heating solu tions with a ten year guarantee on all our mats and cables and a two year warranty on our thermostats Practically speaking you can count on DEVI heating cables and mats lasting as long as the house in which they are installed and that is without having to maintain them Hygiene A
8. completed in English or local language DEVI shall undertake any repair free of charge or supply the customer with a new unit Repairs shall be carried out at no further cost to the customer In the case of faulty Devireg thermostats DEVI reserves the right to repair the unit free of charge and without any unreasonable delays for the customer The DEVI Warranty shall not cover installations that have been carried out by non authorised electricians faults which arise as a result of misuse by other suppliers damage caused by third parties incorrect installations or consequential damage All 25 work will be invoiced in full if DEVI is required to inspect or repair faults that have arisen as a result of any of the above The DEVI Warranty shall not extend to equipment which has not been paid in full DEVI will at all times provide a rapid effective and honest response to all queries and reasonable demands from our customers The above Warranty covers product liability only while purchases are subject to national legislation 26 The DEVI Guarantee Guarantee Certificate The DEVI Guarantee is granted to Name Address Postal code Phone Please observe In order to obtain the DEVI Guarantee the following must be carefully filled in See other conditions on previous page Electrical Installation by Installation date Type of thermostat Production code Suppliers Stamp DEVI A S
9. d period bar L__ flashes indicating this is the day period Setting it in the same way The third period bar L_ flashes indi cating this is the evening period Setting it in the same way The fourth period bar L_ flashes indicating this is the night period Setting it in the same way Note When setting the time periods you cannot step backward to the previous time period until the last one is set This is to ensure that the periods do not overlap 18 Changing the settings Setting the comfort temperature By pressing the e the preset comfort temperature starts flashing You change it with the arrow buttons AV Press the to accept Setting the savings temperature By pressing the e the preset savings temperature starts flashing You change it with the arrow buttons AV Press the to accept It can also be set to OFF Setting the minimum floor temperature limit If the thermostat is installed as a com bination of room and floor sensor the minimum comfort temperature on the floor can be selected Setting this will overrule any other set point as you always want e g 20 C at the floor sensor means that the function is disabled By pressing the e the preset minimum floor limit temperature starts flashing You change it with the arrow AV Press the to accept 19 Special features Childproof mode You disable all buttons in child proof mode by pressing the pinhole bu
10. ed Error code 6 Floor sensor discon nected E 5 Call your electrician Check connections if they are OK then disconnect the 2 sensor wires and connect an ohm meter to sensor wires Measure the ohm value and check with the values in the table in Technical Specifications below Light Indications LED The Devireg 535 has a LED above the 2 pole safety switch The LED has five indications No light The system is turned off Green light System is standing by set point temperature reached Green light flashing Floor sensor is defect Red light System is heating Switching between red The floor temperature limit pre and green light vents the set point room tempera ture from being reached 23 Technical specifications Operation voltage 180 250 VAC 50 60 Hz Standby power consumption Max 0 30W Relay e Resistive load 230V 15A 3450W e Inductive load cos 0 3 Max 4A NTC 15 kOhm at 25 C Sensing values 0 C e 20 C e 50 C Hysteresis 0 2 C with room sensor 0 4 C with floor sensor only 10 to 30 C Frost protection 5 C Temperature range 5 35 C with room sensor 5 45 C with floor sensor only Floor max 20 50 C Floor min 10 45 C only when installed with room and floor sensor combination Sensor failure monitoring The thermostat has a built in monitoring circuit which will switch off the heating if the sensor is disconnected or short circuited Dimensions e Austra
11. g 535 will take care of the rest Display icons and buttons This is the standard display The cur rently measured temperature is shown is shown to symbolize that current temperature is displayed i e unit working as a thermometer The thermostat is operated with the 3 buttons below the display The thermostat can y down be turned On Off A up with the switch e select Two pinhole buttons are available for dedicated features Childproof Locks all buttons Settings 10 Increase decrease temperature The display indicates Weekdays Frost protection Childproof Settings Actual tempera ture is displayed Room temperature Floor temperature Day rhythm periods E and comfort economy Maximum Minimum temperature Increase decrease preferred temperature Use the arrow buttons AV to either increase or decrease the temperature The temperature is changed in incre ments of 0 1 C Notice that the temperature is flash ing Whenever something is flashing you are making changes When the preferred temperature is found you can save the setting in two ways Press to accept Leaving it flashing for 10 seconds 11 Timer function Using the timer function The thermostat has a built in timer function A status bar in the bottom of the display gives an overview of timer status The day is divided into 4 time periods analogous to the typical day program ming pat
12. hing displayed temperature 22 Trouble sholing 3 lt k cont esewnceee eecbeevexeces ti 23 Technical Specifications v 4 0 seeevereeeeaeeeseesaceya 24 Thie DEYTA GUINEE perre rrE poriro EE 25 Install amp configure the thermostat Placement of Devireg 535 When Devireg 535 is used as a room sensor installation height should typically be between 80 150 cm In wet rooms it should be installed on an even surface according to local building regulations At least 50 cm away from windows doors that will be left open occasionally E as 6 gt Not on a wall where it will be subjected to direct sunlight Not on the inner side of a wall facing the outside Installation and connection Installation of Devireg 535 1 Remove the front cover by gently pressing the release tabs on both sides of the thermostat Third groove from the bottom Then remove the frame koa 2 Connect the thermostat according to the connection diagram a Loads below 15 amps b Loads above 15 amps Max Load 15A Switched Mains 180 250V Active to coil of NL Mains 180 250V NL O 2 Contactor rd NO CONNECT i Sensor NO CONNECT 2 N 32 O m O Cv O O O oe o zZ NA WP Choose sensor combination 3 Choose sensor combination When installing the Devireg 535 you need to choose
13. lian plate 118mm x 79mm e Euro plate 85mm x 85mm Disposal Instruction Equipment containing electrical components shall not be disposed together with domestic waste It must be collected separately with other electrical and electronic waste according to local legislation 24 The DEVI Guarantee You have purchased a DEVI heating system which we are sure will serve to improve the comfort and economy of your home DEVI provides a complete heating solution with deviflex heating cables or devimat heating mats Devireg thermostats and devifast fixing strips Should you against all expectations experience a problem with your DEVI heating system you will find that DEVI whose products are manufactured in Denmark and sold throughout the European Union is subject to the standard regulations pertaining to product liability as specified in EU directive 85 374 CEE as well as all applicable legislation in the individual countries on the following conditions DEVI offers a 10 year Warranty on all deviflex heating cables and devimat heating mats and a 2 year Warranty against material defects and production defects in connection with any other DEVI products The guarantee shall be valid only if the WARRANTY CER TIFICATE is completed correctly and in accordance with the instructions and provided the fault is inspected by or submitted to DEVI or an authorised DEVI dealer Please note that the WARRANTY CERTIFICATE must be
14. n page 14 do the following 1 Turn off the thermostat 2 While pressing the pinhole button turn on the thermostat The LED will now flash red green for 1 second indi cating the thermostat will reset 21 Special features Trouble shooting Switching displayed temperature Depending on what mode the thermostat is installed as floor or a combination of floor and room you can change which temperature is displayed If installed as a floor sensor system only you can change the displayed temperature from floor sensor temperature to room sensor temperature if you wish to use the thermostat as a thermometer You change the display by pressing A and V at the same time for 2 seconds The room sensor icon is displayed You press them again to return to the default display If installed as a combination thermostat by pressing A and V at the same time for 2 seconds the temperature in the floor sensor is displayed for 2 minutes The floor sensor icon is displayed Clock symbol flashing S 2 r Time settings were lost due to power u cut The thermostat resumes to manual mode 22 Trouble shooting E4 flashing in display u Error code 4 The thermostat has overheated and has switched off Let the thermostat cool for period Then switch the thermostat off and on If the error persists contact your electrician E5 or E6 flashing in display c c Error code 5 Floor sensor short circuit
15. s DEVI produces only very gentle air circulation the amount of travelling dust particles is reduced considerably a great relief for people with allergies or asthma There are also no dangerous fumes such as carbon monoxide generated by the system Table of content Table of content Install amp configure the thermostats cericcsescrscrisessas 4 Piacemeny OF Devireg 530 4 2504 trari tenni Erne 4 Installation of Devireg 535 cyecespacouyrnaxeuenaeyes 5 Choose sensor COMDINGNONy c 422ete04i kee bad stead 6 Configuration Max floor temp ycs4 dass eevee yes 8 Users suide to Deyireg 535 scee4004 Hea iaddease aes oues 10 NilfQdUCHON 2 4 04284024 ce cree desdomae ede cesar 10 Display icons and DUlONS 2622 202 dices ye seeese reas 10 Increase decrease preferred temperature 11 Using the timer f nctioisersrssrerssr usdi r nrnna 12 S000 ee ee ee a ee ee eee ee nee eee 14 Seine he TMs eresi Eres reser cee es 17 Seting the Weekday c 0heeveeeeacdusetienseees 17 Setting the limer PerlOds 5 c4cuses cox pedadseenee 18 Setting the comfort temperature 19 Setting the savings temperature 19 Setting the minimum floor temperature limit 19 Special ea Uist aoe eee ee Sarees wise eee eee 20 Childproot ModE ecccncadhetersee Gor EEES RES 20 Frost protection MOde 2 2 s 0eereaveneenusees lt 20 OPP MOJE orreee aene fants E 21 Restore timer default settings cicerrcssisecirsirer 21 Switc
16. tern Morning Day Evening Night These are indicated by the L as shown in the picture to the left The start time of each of these can be configured The symbol can be L Empty Indicating that the thermostat is in economy mode w Full Indicating that the thermostat is in comfort mode 12 The 4 programs 4 different programs can be selected Program 1 Manual mode The temperature is maintained constantly 24 hours all week Program 2 The temperature is lowered to economy L L temperature during the day and night period all week P2 is a day program for e g working days where the temperature is decreased during the middle of the day and at night In the morning and evening comfort temperature is preferred Program 3 The temperature is lowered to economy tem L perature during the night period all week P3 is a program for days at home where com fort temperature is preferred during the day and a savings temperature at night Program 4 A week program where Mon Fri Program 2 and Sat Sun Program 3 P4 is a week program with Monday Friday as workdays and Saturday Sunday as days off The top 7 bars indicate Monday through Sun day On week days timer program 2 is used and in weekends timer program 3 Factory setting is Program 1 Manual mode 13 Factory settings The factory setting of the timer is Ea sensor only sensor only Room sensor Temperature
17. tton below with a small screw driver pencil or needle A lock now appears in the display and all other buttons are locked now To unlock press the lock symbol again Frost protection mode To set the thermostat in frost protec tion mode you hold down V until you reach the lowest setting Now press V again to verify that you are not just changing the comfort or economy temperature depending on the mode or timer period the thermostat is in The frost icon now appears and 5 0 flashes You accept the mode by Press to accept Leaving it flashing for 10 seconds The thermostat is now in frost pro tected mode Actual temperature is shown You leave frost protection mode by pressing A 0 5sec 20 Special features OFF mode m pas To set the thermostat in OFF mode you hold down V until you reach 5 0 Now press V again twice to verify that you are not just changing the comfort or economy temperature depend ing on the mode or timer period the thermostat is in The display now shows OFF You accept the mode by Press to accept Leaving it flashing for 10 seconds OFF mode is used if you want to shut off the thermostat for a long period but still keeping the time setting The thermostat is now in OFF mode Two lines are shown in the display You leave OFF mode by pressing A 0 5sec Restore timer default settings To reset the thermostat to its timer defaults as shown o
Download Pdf Manuals
Related Search