Visio-D2523-01-01 SEM1633 User Guide.vsd
Contents
1. 1633 USER GUIDE DIN RAIL MOUNTED RTD RESISTANCE SLIDE WIRE TRIP AMPLIFIER JAN IMPORTANT CE amp SAFETY REQUIREMENTS Important Potentially Hazardous situations Persons responsible for the installation and operation of this equipment must be fully aware of all aspects of this guide Failure to follow the instructions can cause severe injuries and damage This product is suitable for environment Installation category II pollution degree The product is classed as PERMANENTLY CONNECTED EQUIPMENT and must be DIN rail mounted inside a suitable enclosure providing environmental protection to IP65 or greater Dc supply must be derived from a local supply and not a distribution system Max relay contact rating 250 V AC 1 a 30 V DC 1A Any circuit connected to a contact must be fused with a 2 A T fuse To maintain CE EMC requirements input and supply wires must be less than 30 metres The product contains no serviceable parts or internal adjustments No attempt must be made to repair this product Faulty units must be returned to supplier for repair This product must be installed by a qualified person All electrical wiring must be carried out in accordance with the appropriate regulations for the place of installation Before attempting any electrical connection work please ensure all supplies are switched off ABSOLUTE MAXIMUM CONDITIONS To exceed may cause damage to the unit Supply Voltage 50 Vdc Protected for over voltage and reve2. ATION OK NL SENSOR ERROR Nal GREEN ATN RED ATN L HB a2 pan E ALARM LEDS A i ON N27 LB f a ee Orr RED A Trip on outside band POWER OFF When power is off relays go into alarm state T PEN Oils EEAS TRIP ACTIONS l N37 KEY A meee eee o SP Set point ba DB ead TREON Wee Trip on inside band HB High Band TRIP OFF ae LB Low Band 0 TT T55 INVERTED HIGH INVERTED LOW DEVIATION D2523 01 01 SEM1633 User Guide N MECHANICAL INSTALLATION p MOUNTING Screw driver TRIPA TRIPB RANGE E META EN50022 DIN RAIL 17 5mm 56 4 mm Style DIN 43880 1 module width Material Polyamide 6 6 self extinguishing Terminals Screw terminal Cable 2 5 mm Max Colour Grey N CONFIGURATION This product is configured using the USB port of a PC running USB_Speed_Link software available from your suppliers web site During configuration the product is powered direct from the usb port removing the need for additional power If the user wishes to monitor live process data during configuration then powered must be applied Note the input and USB port of the device share the same ground therefore care must be taken to ensure isolation between PC and input circuit This is best achieved by using a portable laptop or notebook PC USB_Speed_Link software is provided with detailed help menu to guide the user through the simple configuration procedure Un
3. less specified at the time of order this product is supplied with the default configuration listed below Factory default Input type PT100 Units C Trip A High Setpoint Trip A 50 Hysterisis Trip A 0 1 Trip B High Setpoint Trip B 50 Hysterisis Trip B 0 1 Filter A ELECTRICAL INSTALLATION 1 0 TURN OFF SUPPLY BEFORE WORKING ON ANY ELECTRICAL CONNECTION 2 0 MAX CONTACT RATING 250 V ac 30 V dc 1 A IMPORTANT FUSE CONTACT CIRCUITS 2 A T 3 0 SUPPLY IS OVER VOLTAGE PROTECTED AND FUSED WITH INTERNAL RESSETTBLE FUSE INPUT Screened Cable p Resistance RTD Screw Driver 3 mm 0 Slide Wire D2523 01 01 SEM1633 User Guide CS 90 mm gt IP65 3 mm LEI 30 C To fit or release module Insert screw driver into slot and lever latch away from body SEM1633 Smart Powered rtd Resistance input dual channel trip Output _ loj xj DOWNLOAD UPLOAD FILESAYE FILELOAD MEMORY RECALL MEMORY HELP SCANDATA READ DATA INPUT CONNECTION For cable length lt 3 Metres no screen or twist pair required RTD inputs all three wire must be equal length resistance Use recommended types for cable length 3 to 30 metres SUPPLY O N C 11 w common Fuse 2 0 A T TRIP B
4. rse connection Current with over voltage 200 mA Input Voltage 5 V between any terminals Input Current 10 mA between terminals Ambient Temperature 30 to 75 C Humidity 10 to 95 RH Non condensing PLEASE REFER TO THE PRODUCT LABEL FOR MANUFACTURERS CONTACT DETAILS Every effort has been taken to ensure the accuracy of this document however we do not accept responsibility for damage injury loss or expense resulting from errors and omissions and we reserve the right of amendment without notice RECEIVE AND UNPACKING Please inspect the packaging and instrument thoroughly for any signs of transit damage If the instrument has been damaged please notify your supplier immediately OPERATION please refer to data sheet for full technical specification CONTROLLER Additional Data Tag number Process Units Process Data I P SIGNAL FILTER TEMPERATURE TRIPS A B User settings UNITS Select filter User settings RTD TEMPERATURE Select C or F Select from 9 Time Trip Action sensor types constant Additional 0 to 100 S Low High sensor can be Proportional downloaded from library Inverted Low High Proportional LINEARISATION f User Setting Set point Select 2 to22 Dead band SIGNAL Signal to process Select either segment Proportional Resistance 0 to 10000 oe High Band l POWER SUPPLY Slide Wire Low Band Input 10 to 48 Vdc 0 to 100 or 10 to 32 Vac Signal RANGE LED l l HIGH LOW DEVI
Download Pdf Manuals
Related Search