Home

Photovoltaic Module Installation Manual (UL)

1. clause 2 hereinafter Limited Peak Power Warranty 13 Phono Solar SHARE THE SUN POWER THE FUTURE Limited Peak Power Warrantv Limited Remedy Twelve 12 vears If within a period of Twelve 12 years from the date of delivery by Phono Solar to the first buver anv Product exhibits a power output less than 9096 of the minimum Peak Power at STC as specified as of the Phono Solars product label provided that such loss in power is determined bv Phono Solar at its sole and absolute discretion to be due to defects in material or workmanship Phono Solar will at its sole option either 1 replace such loss in power by either a providing additional Product s to the Customer to make up for such loss in power or b replacing the defective Products s at the option of Phono Solar or 2 refund the percentage of the cost of the Product s as measured bv the then prevailing market price for similar Product s to the Customer representing the percentage of the power output less than 9096 the minimum Peak Power at STC 1 as specified as of the Phono Solars product label The remedies set forth in this clause 2 shall be the sole and exclusive remedies provided under the Limited Peak Power Warrantv Twentv Five 25 vears If within a period of Twentv Five 25 vears from the date of deliverv bv Phono Solar to the first buver anv Product exhibits a power output less than 8096 of the minimum Peak Power at STC 1 as specified
2. 5 9 Lengtht50mm Module Frame Clamp Y B Clamping svstem d Attachment to the long frame 103mm 103m1 Use four clamps Use four clamps Use four clamps Use six clamps Clamping Range Long Frame Centret 150mm Mounting Rail M8 Screw Width Module installed using Clamp Fitting method Clamping Range Tong Frame Centret150mm Use four clamps on the short frame and two clampsat the center of each long frame Select the appropriate installation method depending on the load see below for more Clamping system Attachment to the short frame detailed information 1580mm x 808mm x 35mm DIAMOND Series insertion system ONVX Series 1640mm x 992mm x 40mm DIAMOND Series ONVX Series Insertion system 5 a m z o 3 2 a 3 W9JSAS uonu su Insertion system 1956mm x 992mm x 40mm DIAMOND Series Insertion system Use insertion system on short frame Use insertion system on a short frame and two clamps at the center of each long frame ONYX Series Use an insertion system on along frame 06 07 Phono Solsr SHARE THE SUN POWER THE FUTURE Phono Solar U Tvpe module Clamping svstem ese Mounting system Attachment to the long frame Clamping system Attachment
3. Solar SHARE THE SUN POWER THE FUTURE Limitation of Warranty Scope These warranties as set forth herein are expressly in lieu of and exclude all other warranties of any kind whatsoever whether express or implied including but not limited to warranties of merchantability of fitness for particular purpose use or application of non infringement and all other obligations or liabilities on the part of Phono Solar unless such other obligations or liabilities are expressly agreed to in writing signed and approved by Phono Solar to the broadest extent permitted by law Phono Solar shall have no responsibility or liability whatsoever for damage or injury to persons or property or for other loss or injury resulting from any cause whatsoever arising out of or related to the Product s including without limitation any defects in the Product s or from use or installation Under no circumstances shall Phono Solar be liable for any special punitive incidental or consequential damages howsoever caused including but not limited to loss of use loss of profits loss of production or loss of revenues arising directly or indirectly from the sale or use of any Product s whether such claim is based on warranty contract negligence strict liability or otherwise Phono Solar s aggregate liability if any in damages or otherwise shall not exceed the invoice value as paid by the Customer for the single unit of Product s involved The rights and
4. as of the Phono Solars product label provided that such loss in power is determined bv Phono Solar at its sole and absolute discretion to be due to defects in material or workmanship Phono Solar will at its sole option either 1 replace such loss in power by either a providing additional Product s to the Customer to make up for such loss in power or b replacing the defective Products s at the option of Phono Solar or 2 refund the percentage of the cost of the Product s as measured by the then prevailing market price for similar Product s to the Customer representing the percentage of the power output less than 8096 the minimum Peak Power at STC 1 as specified as of the Phono Solars product label The remedies set forth in this clause 2 shall be the sole and exclusive remedies provided under the Limited Peak Power Warrantv 14 Stability Reliability Creativity Exclusions and Limitations 1 In any event all warranty claims must be received within the applicable warranty period for this warranty to be effective 2 The Limited Product Warranties and the Limited Peak Power Warranties do not apply to any Product s which have been subjected to e Misuse abuse neglect or accident e Alteration improper installation or application e Non observance of Phono Solar s installation manual e Impairments caused by external effects such as e g dirt stains smoke damages caused by salt by chemicals
5. load calculation and security of the photovoltaic system 41 Any hardware used must be compatible with the mounting material to avoid galvanic corrosion 4 22 Only use connectors that are designed for photovoltaic systems and that match PHONO SOLAR modules 43 When working with the connectors only use tools as recommended by the connector manufacturer 4 4 PHONO SOLAR recommends that the same type of modules are connected together in order to avoid any system power loss 4 5 The maximum number of series connected modules depends on system design the type of inverter used and environmental conditions 4 6 Select insulated cables that are able to resist to ultraviolet radiation and extreme weather conditions 4 7 The rated voltage of the cable chosen must be appropriate to the overall maximum voltage of the system 4 8 The module frame must be grounded according to local regional and state 10 Stability Reliability Creativity safety and electrical standards Ensure that a recommended connector or equivalent is used for the grounding cable The grounding cable must be properly fastened to the module frame B GROUDING 5 1 For grounding and bonding requirements please refer to regional and national safety and electricity standards If grounding is required use a recommended connector type for the grounding wire 5 2 For grounding this guide refers to module frame grounding If grounding is required make sure module frames
6. metal exposed to touch are always grounded 5 3 System grounding is not mandatory for Phono Solar modules however negative system grounding may be required by local authorities and can therefore be recommended 5 4 Phono Solar recommends the Grounding Clip Cat No 1954381 Supplier TE when grounding Please refer to relevant connector specifications for instructions For grounding clip Using a cross recessed screwdriver thread the screw into the hole until the head is flush with the base and the base is flush with the frame then tighten the screw with another to turn Insert the wire into the wire slot Press down on both ends of the wire the wire slot will cause the wire to form a slight curve Manually or using channel lock pliers push the slider over the base until it covers the base This will terminate the wire For Grounding Clip with 6 32 or 10 32 Screw and Hex Nut Shown or Nut with Lock Washer Figure 3 11 Phono Solar SHARE THE SUN POWER THE FUTURE MAINTENANCE In order to ensure optimum module performance PHONO SOLAR recommends the following 61 If necessary the glass front of the module can be cleaned with water and a soft sponge or cloth A mild non abrasive detergent can be used to remove more stubborn stains 6 2 Check the electrical and mechanical connections periodicallv and make sure they are clean safe complete and secure 6 3 In the event of a problem consult with a licen
7. not explicitly authorized for use e g for cleaning Repair or modifications by someone other than an approved service technician of Phono Solar e Power failure surges lightning flood fire accidental breakage or other events out of Phono Solar s control e Caused by external events including but not limited to defective equipment parts appliances system components like connecting cables invertors or the like which have been coupled with the Module by anyone other than Seller or caused by defective system design configuration or installation planning e Removal of Modules and reinstallation at a new site e Installation on mobile platforms or in a marine environment direct contact with corrosive agents or salt water pest damage or malfunctioning system components e Alteration removal or obliteration of the original Module label e Other events that are reasonably beyond the control of Phono Solar 3 Both the Limited Product Warranties and Limited Peak Power Warranties do not cover any costs associated with installation removal or re installation of the PV modules and except as explicitly set forth in the final paragraph of Section 5 customs clearance or any other costs for return of the Product s 4 Both the Limited Product Warranties and Limited Peak Power Warranties do not cover cosmetic blemishes associated with installation or the normal wear and tear of Phono Solar Modules 15 Phono
8. Phono Solar SHARE THE SUN POWER THE FUTURE Phono Solar Technologv Co Ltd PHONO SOLAR TECHNOLOGS CO LTD Photovoltaic Module Tel 486 25 5863 8000 Fax 486 25 5863 8009 a Installation Manual UL E mail support phonosolar com Website www phonosolar com Add No 2 Xinke Road Nanjing Hi tech Zone Nanjing China Version UL 2013 01 Copyright PHONO SOLAR 2013 Phono Solar SHARE THE SUN POWER THE FUTURE CONTENTS 1 IMPORTANT SAFETV GUIDE PRODUCT IDENTIFICATION MECHANICAL INSTALLATION ELECTRICAL INSTALLATION GROUDING MAINTENANCE l Oy UT cc GID DISCLAIMER OF LIABILITY Phono Solsr SHARE THE SUN POWER THE FUTURE Hu DO NOT use mirrors or magnifiers to concentrate sunlight onto the module he back of the DO NOT paint the module or attach anything on to module DO NOT attempt to disassemble he modules and do not remove any attached nameplates or components from the module N DO NOT lift or move the module bv holding the junction box or cable module surface DO NOT place anvthing on he module or press on the DO NOT drop the module or allow objects to fall on the module Ne J a QUOT sans DO NOT expose the back of the module to dir
9. W per m2 and c a cell temperature of 25 degree centigrade at right angle irradiation The measurements are carried out in accordance with IEC 61215 as tested at the connectors or junction box terminals as applicable per calibration and testing standards of Phono Solar valid at the date of manufacture of the PV modules The power output shall be measured by a laboratory approved by Phono Solar 18
10. ample any necessary licenses must be obtained prior to the installation commencing Regulations around vehicles and ships must also be observed during the installation e Observe all safety rules for the other system components including the cables connectors charging controllers inverter and storage battery etc e Do not place the modules near a location where flammable gases are either generated or collected e Insulated gloves must be worn during the installation e Do not wear metal ornaments during the installation e Do not drill holes in the frame e Under normal conditions a module is likely to produce more current and or voltage than reported under Standard Test Conditions STC Accordingly the values of Isc and Voc marked on the module nameplate should be multiplied by a factor when determining the component voltage ratings conductor current ratings fuse sizes and the size of controllers connected to the photovoltaic system The exact factor value should be suggested by a licensed qualified person e The connecting ends with electricity may cause fire spark or lethal shocks even when the modules are not connected e Electricity can be generated when the modules are exposed to sunlight even if they are not connected It is dangerous to touch 30V DC or higher so never open the electrical connectors or unplug the electrical connectors while the circuit is under load and do not touch the end with electricity during installatio
11. ect In connection with both the Limited Product Warranties and Limited Peak Power Warranties Phono Solar shall reimburse Customer for reasonable customary and documented transportation charges by sea freight for both the return of the Product s and reshipment of any repaired or replaced Product s only if this cost is authorized by Phono Solar customer service department Severability If a part provision or clause of this Limited Warranty for PV Modules or the application thereof to any person or circumstance is held invalid void or unenforceable such holding shall not affect and shall leave all other parts provisions clauses or applications of this Limited Warranty for PV Modules and to this extent such other parts provisions clauses or applications of this Limited Warranty for PV Modules shall be treated as severable Disputes In case of any discrepancy in a warranty claim a first class international test institute such as Fraunhofer ISE in Freiburg Germany TUV Rheinland in Cologne Germany or ASU Arizona State University shall be involved to judge the claim finally All fees and expenses shall be born by the losing party unless otherwise awarded The final explanation right shall be borne by Phono Solar Various The repair or replacement of the Product s or the supply of additional Product s does not cause the beginning of new warranty terms nor shall the original terms of thi
12. ect sunlight J conditions f Do NOT install or handle module in wet or strong windv Do NOT wear metal ornaments while handling the module or during the installation DO NOT drill holes in the frame DO NOT use mo equipment or in ammable gases generated or coll dule near places where mav be ected nsulated gloves must be worn while handling the module and during the installation Stability Reliability Creativity IMPORTANT SAFETY GUIDE This manual contains information regarding product identification and the safe installation and maintenance of photovoltaic modules hereafter referred to as module supplied by PHONO SOLAR TECHNOLOGY CO LTD hereafter referred to as PHONO SOLAR The term module can be interpreted as a single module or multiple modules depending on the context Installers must already be familiar with the mechanical and electrical requirements for a photovoltaic system Installers must also read this manual carefully prior to installation We recommend that you keep this manual in a safe place for future reference and in case of future sale or disposal of the module 11 General Safety e The installation of a photovoltaic system requires specialized skills and knowledge and must only be carried out by licensed qualified persons e Installers should assume all risks of inj
13. einafter the Product in this Warranty means the Standard PV Module s manufactured by Phono Solar Technology Co Ltd hereinafter the Phono Solar The Phono Solar warrants its Product s in compliance with the terms and conditions as stipulated below The Customer in this Warranty means the individual person or company who purchases Phono Solar Product This Limited Warranty for PV Modules is valid for all Standard Modules delivered from Phono Solar since 19th August 2013 Limited Product Warranty Repair or Replacement Ten 10 years Phono Solar warrants that the Product including factory assembled DC connectors and cables if any will be free from defects in material and workmanship under normal application installation operation use and service conditions If Product fails to conform to this warranty within a period of ten 10 years from the date of delivery by Phono Solar to its first buyer Phono Solar will at its sole discretion either repair the defective Product s at no charge or replace the defective Product s or part thereof by a new or remanufactured equivalent at no charge within the above specified period This repair or replacement remedy shall be the sole and exclusive remedy provided under the Limited Product Warranty and shall not extend beyond the ten years period set forth herein This Limited Product Warranty does not warrant a specific power output which shall be exclusively covered under
14. limitations herein shall leave unaffected any legal rights existing under mandatory applicable laws Obtaining Warranty Performance If the Customer has a justified claim covered by this Limited Warranties for PV Modules an immediate notification directly to Phono Solar shall be filed by mailing a registered letter in writing to the address of Phono Solar listed hereunder or by sending an email letter to the email account of Phono Solar Service Center listed hereunder within Ten 10 weeks after becoming aware of the circumstances which constitute a warranty case Together with the notification the Customer should enclose the following information e The name and address of the Customer e The corresponding serial number of the Product s e The date on which the Product s have been delivered and installed 16 Stability Reliability Creativity e The pictures of the defective Module which show the defect and or the pictures which show the shadowing situation at the installation location The timely receipt of the notification by Phono Solar shall be decisive The return of any PV modules will not be accepted unless prior written authorization for the return and evaluation of the claimed defect has been given by Phono Solar To the extent necessary for processing the return request Phono Solar or its authorized person shall be given commercially reasonable access to the Product s for inspection and analysis of the claimed def
15. m Use four clamps on the short frame and two clamps at the center of each long frame Insertion system f A ID Clamping Rang 100mm 17 JI Insertion system z 8 Ed 8 S a K 4 8 3 Use insertion system ona short frame and two clamps at the center of each long frame Use an insertion system on along frame 09 Phono Solsr SHARE THE SUN POWER THE FUTURE u Warning Do not attempt to drill holes in the module frame or in the glass surface of the module Any such modifications will void the PHONO SOLAR product warranty 3 4 When installing a module on a pole ensure that the pole and mounting rail can withstand anticipated local winds The pole must be installed on a hard base 3 5 Ensure that the installation height is such that the lowest modules will not be covered by accumulated snow or shaded by the surroundings 3 6 Ensure that there is adequate ventilation under the modules conforming to local regional and state standards and regulations 3 7 A minimum distance of 10cm between the roof plane and the frame of the module is generally recommended 3 8 Observe the linear thermal expansion of the module frames A minimum distance of 1cm between two modules is generally recommended ELECTRICAL INSTALLATION Note All instructions hereafter are for reference only licensed qualified person or installer must be responsible for the design installation mechanical
16. mes e Do not place the modules near a location where flammable gases are either generated or collected Notel Saline environments can accelerate the processes of electrical insulation losses and galvanic corrosion especially when different metals with high electrochemical potential come into contact each other In saline environments Phono Solar PV modules must be installed under the following conditions e Modules shall not be installed in direct contact with salty water that is in offshore e g platforms and marine e g piers boats applications e Modules installed in locations where the distance from the sea is less than 500 m shall fulfill the following requirements e The modules shall be mounted with a minimum tilt angle of 10 with respect to the horizon e In case of fixing the modules using the 8 mounting slots all the hardware washers screws and nuts shall be made of stainless steel e To avoid possible galvanic corrosion between the aluminum frame and the support structure PVC washers or neoprene tape shall be interposed between the two metals e In the case of grounding the module frames stainless steel hardware must also be used Note2 In ammonia environments Phono Solar PV modules must be installed under the following conditions e In case of fixing the modules using the 8 mounting slots all the hardware washers screws and nuts shall be made of stainless steel e To avoid possible galvanic corrosion betwee
17. n the aluminum frame and the support structure PVC washers or neoprene tape shall be interposed between the two metals e In the case of grounding the module frames stainless steel hardware must also be used 04 Stability Reliability Creativity 3 2 Select suitable mounting rails e Please observe the safety regulations and installation instructions included with the mounting rail If necessary please contact the supplier directly for further information e The modules must be safely set onto the mounting rail The whole rail supporting the photovoltaic system must be strong enough to resist potential mechanical pressures caused either by wind or snow in accordance with local regional and state safety and other associated standards e Make sure that the mounting rail will not deform or affect the modules when it expands as a result of thermal expansion e The mounting rail must be made of durable anti corrosive and UV resistant materials 3 3 Select suitable mounting methods PHONO SOLAR modules can be mounted using two methods Screw Fitting Use corrosion proof screws in the existing installing holes in the module frame Each module has 8 mounting holes for securing the module on the mounting rail The module frame must be attached to a mounting rail using M8 corrosion proof screws together with spring washers and flat washers in symmetrical locations on the module The applied torgue should be approximately 8Nm Please fi
18. nd detailed mounting information in the below illustration Module Frame Mounting Rail Mg Bolt Module Frame b u Split Washer Mounting Rail M8 Screw Flat Washer LS a Ne s S Module installed using Screw Fitting method 05 Phono Solsr SHARE THE SUN POWER THE FUTURE Stability Reliability Creativity Clamp fitting Using suitable module clamps on the LONG side of the module frame Phono Solar F Type module to mount the modules is portrait orientation mode while on the SHORT side of the module frame is landscape orientation mode 2400 Pa Load 3800 Pa Load 5400 Pa Load The module clamps should not come into contact with the front glass and must not deform the module frame Avoid any shadowing effects from the module clamps The module frame can not be modified under any circumstances Regardless of the orientation chosen at least 4 clamps must be used on each module For portrait orientation 2 clamps should be attached to the long sides of the module and for lt Mounting system landscape orientation 2 clamps should be attached to the short sides of the module l na P Use eight mounting holes Depending on the local wind and snow loads additional clamps may be required The 103mm 103m applied torgue should be about 8Nm Please find detailed mounting information in the below illustration 5 9 Lengtht50mm
19. ns when the modules are exposed to sunlight e Children should be kept away from the photovoltaic system e In order to prevent current and voltage generation during installation an opaque board can be used to cover the modules e Only use licensed qualified insulated tools e The frame of the modules must be grounded according to local regional and state safety and electrical standards A recommended connector or equivalent must be used for 02 Stability Reliability Creativity the grounding cable The grounding cable must be appropriately fastened to the module frame e Only Balance of System BOS in conformity to local regional state safety electricity standards and photovoltaic system such as connectors cables and frames can be used avoiding affect on the module performance and or damage it 14 Fire Safety e Consult your local authority for guidelines and requirements for building or structural fire safety e Roof constructions and installations may affect the fire safety of a building an improper installation may create a hazard in the event of a fire e Use components such as ground fault circuit breakers and fuses as required by the local authorities e Do not use the modules near a location where flammable gases are either generated or collected e The modules have been rated Fire Class C and are suitable for mounting onto a Class A roof PRODUCT IDENTIFICATION On the back of each module there are 2 labels
20. s Limited Warranty for PV Modules be extended Any replaced Product s shall 17 Phono Solsr SHARE THE SUN POWER THE FUTURE become the propertv of Phono Solar made for their disposal Phono Solar has the right to deliver another tvpe different in size color shape and or power in case Phono Solar discontinued producing the replaced Product s at the time of the claim Warranty Transfer This warranty is transferable from the original Customer to any assignee and remains in effect for the time period remaining under the limited warranties provided the Product remains installed in its original location at the warranty registration Force Majeure Phono Solar shall not be responsible or liable in any way to the customer or any third party arising from any non performance or delay in performance of any terms and conditions of sale including this Limited Warranty for PV Modules due to acts God war riots strikes warlike conditions plague or other epidemics fire flood or any other similar cause or circumstance beyond the reasonable control of such Phono Solar In such cases performance by Phono Solar of this Limited Warranty shall be suspended without liability for the period of delay reasonably attributable to such causes 1 Peak Power at STC is the power in Watt peak that a PV Module generates in its Maximum Power Point STC are as follows light spectrum of AM 1 5 b an irradiation of 1000
21. sed qualified person DISCLAIMER OF LIABILITY Since it is impossible for PHONO SOLAR to control installation operation application and maintenance of the photovoltaic system according to this instruction PHONO SOLAR does not accept responsibility and expressly disclaims liability for any loss damage or expense arising out of or in any way connected with such installation operation use or maintenance PHONO SOLAR will not take any responsibilities for any possible violation of patent rights and third party rights that are related to application of the solar energy system No permission of patents is given through implication The information of this instruction is from knowledge and experiences of PHONO SOLAR and so it is reliable However the instructions and suggestions of this instruction do not make an external or internal of guarantee PHONO SOLAR reserves the right to revise this instruction products and all the information about products without prior notification to customers 12 Stability Reliability Creativity Limited Warranty for PV Modules Version EN 2013 V2 Phono Solar Standard PV Modules with the Model Names covered under this warrantv are PSXXXM 24 F XXX 180 185 190 195 200 205 210 PSXXXM 20 U XXX 230 235 240 245 250 255 260 265 270 PSXXXP 20 U XXX 230 235 240 245 250 255 260 265 PSXXXM 24 T XXX 280 290 300 310 320 330 PSXXXP 24 T XXX 280 290 300 310 320 330 The product her
22. that provide the following information Nameplate Describes the product type rated power rated current rated voltage open circuit voltage short circuit current all as measured under STC weight dimensions etc the maximum system voltage of 1000V DC Warning The value of Voc times the number of modules in series should not be bigger than the maximum system voltage marked in the nameplate Barcode This is used to identify each module Each module has a unique and traceable serial number in the form of barcode The barcode of each PHONO SOLAR module has 15 letter digits Warning Do not remove the nameplate or barcode The PHONO SOLAR product A warranty will be void if either the module nameplate or barcode is removed MECHANICAL INSTALLATION Note All instructions hereafter are for reference only A licensed qualified person or installer must be responsible for the design installation mechanical load calculation and security of the photovoltaic system 03 Phono Solsr SHARE THE SUN POWER THE FUTURE 3 1 Select suitable locations for installation e Select a suitable location for installing the modules e PHONO SOLAR recommends that to achieve the best performance the modules should face south in northern latitudes and north in southern latitudes The exact tilt angle and orientation of mounted modules should be recommended by a licensed qualified installer e The modules should be completely free of shade at all ti
23. to the short frame Insertion System 2400 Pa Load 1 4 Length50 Use four clamps on short frame im system Insertion system Use insertion system on short frame 3800 Pa Load 5 9 Length 50mm Use four clamps 08 5 9 Length 50mm 5400 Pa Load l Use eight mounting holes Clamping l 1001 Clamping Range ong Frame Centre 150mm Clamping Range Tong Frame Centres 150mm AJ Use four clamps on the short frame and two clamps at the center of each long frame Clamping Range 100mm insertion system A 8 2 o 3 3 Insertion system Use insertion system ona short frame and two clamps at the center of each long frame Use an insertion system on along frame Phono Stability Reliability Creativity Solar T Type module Mounting system Clamping system Attachment to the long frame Clamping system Attachment to the short frame Insertion System 2400 Pa Load 1 4 Length 50mr 3800 Pa Load 5400 Pa Load ir e 5 9 Length 50mm Use eight mounting holes 5 9 Length 5Omm S S z gi N Use four clamps Use four clamps Ez Clamping Range Long Frame Centre 150mm Width 501 Clamping Range Long Frame Centres 150m
24. ury and do everything to avoid potential damages and risks that might occur during installation including but not limited to the risks of electric shock e PHONO SOLAR modules do not need special cables for connection All of the modules have permanent junction boxes cables and connectors e Do not use mirrors or magnifiers to concentrate sunlight onto the modules e The modules generate DC electrical energy from sunlight They are designed for outdoor use and can be mounted onto frames on rooftops or in the ground etc e Do not paint the module or attach anything on to the back of the module e Do not attempt to disassemble the modules and do not remove any attached nameplates or components from the modules 12 Handling safety e When handling the module insulated gloves must be worn e Inappropriate transportation and installation may break the module e Do not lift or move the module by holding the junction box or cable e Do not place anything on the module or press on the module surface e Do not drop the module or allow objects to fall on the module e Do not expose the back of the module to direct sunlight e Do not wear metal ornaments while handling the module 01 Phono Solar SHARE THE SUN POWER THE FUTURE e Do not install or handle modules in wet or strong windy conditions 13 Installation safety e Local regional and state laws and regulations must be adhered to while installing a photovoltaic system For ex

Photovoltaic Module Installation Manual (UL)

Contents

Download Pdf Manuals

Related Search

Related Contents