Auto-Darkening Filter Welding Helmet User's Manual - Sklep e-SZOP
Contents
1. 6 Infrared ray transmittance rate 780 1300 lt 0 0027 1300 2000nm lt 0 097 Dark shade 7 13 from bright to dark Light shade 4 Auto reaction time 0 0001s Recovery time 0 6s from dark to bright Power supply AAA CAUTION Before welding 1 When a new auto darkening welding helmet is used for the first time the operator should remove the protective films on the cover Lens otherwise the shade level may be incorrect or fail to work 2 Make sure that batteries are correct and suitable for the work you then do PARTS BREAKDOWN O DO MONN TT mm 1 Front cover Lens 7 2x limitation washers R amp L 2 Auto darkening welding filter 8 2x Position washers 3 Helmet 9 2 x screws 4 2x Nuts 10 Head band 5 2X washers 11 Headgear 6 2X position washer 12 Dark shade adjusting knob OPERATION When you are sure you have familiar with all the information included above and get every thing ready to use the welding helmet follow the instructions below 1 Taking up the welding helmet gently press the ON button on the auto darkening welding filter to power on 2 Setting correct dark shade by turning the dark shade adjusting knob according to the welding 3 Put on the helmet At this moment you can see work piece and other things clearly 4 Start your welding work and the view window will turn to intended dark shade state you had set immediately If it fails stop at once and chec2. AW Shielded Semi Automatic Are Welding MIG light MIG on light alloys PAC Plasma Are Cutting PAW Plasma Are Welding
3. Auto Darkening Filter Welding Helmet User s Manual A WARNING A o 1 Itis your job to keep your self and others from the hazards associated with welding To do this you must familiarize your self with safety rules for arc welding Handling high pressure gas cylinders and general safety rules 2 Arc welding gives off fumes which can be potential health hazard Always use adequate ventilation 3 Never do welding work without adequate eye protection 4 Always wear appreciate safety equipment when welding OWNER S RESPONSIBILITY The owner and or operator shall have an understanding of these operating instructions and warnings before operating the filter If the user knows little English this instruction shall be read to and discussed in the operator s native language by the purchaser owner making sure that the operator comprehends its content TROUBLE SHOOTINGTR 1 If the auto darkening speed and shade state level decrease the batteries are low Replace the batteries 2 If the view window will not lighten or become clear either power switch is OFF or batteries are low Turn on the switch or replace batteries 3 When the light transmittance of the protective sheet in front of the lens is low replace with a new one The standard size is 113x 78 x 1 0mm SPECIFICATIONS View window area 91X40mm Auto darkening filter dimension 120X95X13 mm Ultraviolet ray transmittance rate 313 365nm lt 2x10
4. k Make sure you have overcome the problem before try aging 5 Power AUTO OFF when finish welding CAUTION Batteries shall be removed when long time off use WARNING This Auto darkening Welding Helmet is not suitable for laser welding This Auto Darkening Welding Helmet and the Auto darkening Welding Filter shall never be placed on hot surfaces Never open or tamper with the Auto Darkening Filter This Auto darkening welding helmet will not protect against severe impact hazards including fragmenting grinding disks and they must never be used for grinding This Auto darkening welding helmet will not protect against explosive devices or corrosive liquids Don t make any modifications to either the filter or helmet other than those specified in this manual Don t use any replacement parts other than those specified in this manual Unauthorized modifications and replacement parts will void the warranty and expose the user to the risk of personal injury Should the Auto darkening welding helmets not darken upon striding an arc stop welding immediately and contact your supervisor or your dealer Don t immerse the filter in water Don t use any solvents on filters screen or helmet components Use only at temperatures 5 C 55 C 23 F 131 F Storing temperamre 20 C 70 C 4 F 158 F Protect filter from liquid and dirt contact Clean filters surfaces regularly do not use strong cleaning soluti
5. ons Always keep sensors and solar cells clean using a clean lint free tissue cloth Regularly replace the cracked scratched pitted Front Cover Lens Severe personal injury could occur if the user fails to follow the aforementioned warnings and or fails to follow the operating instructions MAINTENANCE A Warning Replacement of any components and or parts shall be original from the manufacturer User shall not uninstall the auto darkening welding filter The filter must be removed by the local dealer or qualified personnel Other wise it will cause the warranty invalid Replacing the Cover Lens if it is damaged cracked scratched soiled or pitted 1 Front cover lens 1 1 Remove the filter 1 2 Remove the front cover lens 1 3 Replace a new front cover lens 1 4 Install the filter again Cleaning The Auto darkening Welding Filter with a clean lint free tissue or cotton cloth Don t immerse the lens in water or any other liquid Never use abrasives solvents or oil based cleaners Don t try to open the Auto darkening Welding Filter STORAGE The helmet and the auto darkening welding filter shall be stored in dry and well ventilated place Do not exposed to direct sunshine Do not hit click scratch or squeez the helmet Do not dirty the welding filter Are Current Amperes Note SMAW Shielded Metal Are Welding TIG GTAW Gas Tungsten Are Welding GTAW TIG MIG heavy MIG on heavy metals S
Download Pdf Manuals
Related Search