Yealink DECT Repeater RT10 User Guide-1
Contents
1. To deactivate the verification tone repeat the above steps www yealink com2. s O m Ho wm To install the repeater using the supplied screw Wall j Screw anchor is used to fix Wall Mount DECT Repeater RT10 User Guide the screw on concrete wall Introduction Yealink DECT repeater RT10 is designed in accordance with Digital Enhanced Cordless Telecommunication DECT standard It can be deployed to extend the range of the W52P IP DECT phone to cover areas where reception was previously not available All the usual handset functions are supported by the base station in the extended radio range The repeater base station and cordless handset employ wireless connection Signals are exchanged without acoustical and visual differences Multiple Repeaters Up to 6 repeaters can be registered to one base station to extend available reception range for all registered handsets All repeaters must be installed within the base station coverage area up to 300m in unobstructed outdoor areas and up to 50m inside buildings as shown in the figure below It is not possible to install the repeaters in series or daisy chain The maximum number of handsets that can be registered to your base station is not affected by the repeater The repeater can be used to extend the coverage range in all directions allowing several floors to be covered The automatic hand
3. Yealink E COSY VoIP i DECT Repeater RT10 User Guide QE eee www yealink com Packaging Contents The following items are included in your package Yealink Repeater Power Adapter User Guide Screw pme g Screw Anchor Appearance Instructions Yealink REPEATER LED Status LED Indicator Wall Mount Hole DC Jack The DECT repeater has one LED indicator describing the repeater operations The following table provides instructions on repeater operations and LED indications LED Indication Operation Off Power off Red Slowly flashes Unregistered ready for manual registration Red Double flashes Unregistered ready for auto registration DECT Repeater RT10 User Guide LED Indication Operation Red Steady on Registered to base station ready for use Red Shortly flashes Attempting handset connection Installation To connect the power for the repeater 1 Connect the DC plug on the power adapter to the DC jack on the repeater 2 Connect the other end of the power adapter to the AC outlet O Sp 5 E k 7
4. e handset used was already registered to the base station Now the LED indicator flashes fast without interruptions 5 Assign a repeater number You must now assign a repeater number to the repeater choose from 2 to 7 for up to 6 repeaters a Press 9 and the off hook key on the handset The LED indicator illuminates b Press a number between 2 and 7 When the repeater has accepted the chosen number the LED indicator will flash a corresponding number of times If you miss the confirmation flash press the number again c Accept the registration by pressing the key and then press the on hook key The repeater is now automatically restarted the LED indicator goes off for 2 seconds flashes for a brief moment and then stays illuminated The registration of the repeater is completed You can now disconnect the power adapter and move the repeater to the selected location disconnecting the power will not clear the registration Note Each number can be only assigned once when using more than one repeater on a base station Repeater number and handset number are independent of each other De registration If you want to register the repeater to another base station using the auto registration method de register the repeater beforehand as described below 1 Switch off the repeater disconnect the power adapter 2 Switch it on for 1 to 5 seconds and switch it off again 3 Switch it on for 25 to 35 seconds and switch it o
5. f Base Station Long press paging Repeater key Switch on again d Base Station Repeater Long wes paging A yi Switch on v a a Repeater No Repeater LED flashes without LED flashes with interruptions interruptions Repeater LED flashes y v Handset Base Station Dial out 9 Set password to 0000 Repeater y LED stays on Repeater Handset LED stays on Re register to base station r Handset Repeater Ready for use Press niba 2 7 LED flashes without and key interruptions Hang up Ready for use DECT Repeater RT10 User Guide Verification Tone To find the best possible location for the repeater you may need to try various locations Place a call and walk around with the handset to determine the base station s coverage area The verification tone allows you to easily check the extent of the repeater s coverage area The tone is audible on the handset during a call To activate the verification tone on the repeater 1 Switch off the repeater disconnect the power adapter 2 Switch it on for 1 to 5 seconds and switch it off again 3 Switch it on again The LED indicator on the repeater flashes slowly 4 Switch it off again 5 Switch it on again The verification tone is then activated Place a call using the handset to check whether the handset is working in the extended area of the repeater If the call is successfully handled by the repeater you can hear the verification tone from the handset every few seconds
6. ff again After a while the LED indicator on the repeater double flashes and the repeater is ready for a new auto registration Placement To achieve optimum performance for the repeater it is important to find a good location Here are a few tips for placing repeaters e Choose a rasied position for both the base station and repeater wherever possible e When positioning the repeater avoid obstacles that can interfere with radio transmission such as thick wall and metal structures that may be in the coverage area between the base station and repeater e Avoid interference from other electrical appliances such as micro wave ovens Hi Fi equipment computers etc nm www yealink com e Keep a minimum of 10 meters between multiple repeaters to avoid coverage areas overlapping Note The LED indicator remains on constantly after the repeater has been switched on If the LED flashes the repeater is too far away from the base station or reception is hindered by obstacles The flow diagrams of these two registration methods are shown below Auto Registration Manual Registration Base Station Base Station i Switch on Switch on Repeater Switch off Handset Enable repeater mode Handset Enable repeater mode Renis Switch on 1 5s and of
7. over process is seamless If the repeater is placed correctly overlapping the coverage area of the base station the handsets can move freely within the total coverage area while on a call nnn www yealink com Registering the Repeater The repeater can be registered to a base station in two ways Auto Registration and Manual Registration Before registering the repeater you need to enable the repeater mode on the handset For more information on how to enable the repeater mode refer to Yealink W52P User Guide Note Auto Registration cannot be performed if the repeater is already registered to one base station In this case de register the repeater before attempting auto registration For more information refer to De registration Auto Registration Using the auto registration method the repeater can be registered to a base station To register a repeater automatically 1 Switch on the repeater and check if the LED indicator on the repeater double flashes If the LED indicator does not double flash you need to de register the repeater first Please refer to De registration If the LED indicator double flashes go to step 2 2 Switch off the repeater disconnect the power adapter 3 Set the base station in registration mode Long press the paging key on the base station till the first LED flashes 4 Switch on the repeater connect the power adapter The LED indicator on the repeater flashes Afte
8. r a short while the LED indicator stays on permanently indicating that registration is completed and the repeater is ready for use The first LED on the base station flashes after the registration is completed You can press the paging key to cancel the flash Note If the registration is not successful the LED indicator will flash continuously In this case repeat steps 2 4 Manual Registration The repeater base station and handset must be accessible before performing the registration If you want to register more than one repeater the registration must be performed separately for each repeater To register a repeater manually 1 Set the repeater in registration mode Switch on the repeater for 1 5 seconds and then switch it off Switch it on once more and leave it there The LED indicator on the repeater flashes slowly You now have five minutes to complete the registration If the registration is not completed within this period you must start over again 2 Set the base station in registration mode Long press the paging key on the base station till the first LED flashes 3 The LED indicator on the repeater flashes DECT Repeater RT10 User Guide If the LED flashes fast without interruptions go to step 5 If the LED flashes fast with interruptions go to step 4 4 Registration of handset If the password of the base station has been changed reset it to 0000 You must re register the handset even if th
Download Pdf Manuals
Related Search