Troubleshooting Package contents Εco Light dimensions in mm
Contents
1. Page 5 from 6 Battery replacement process iT Ben ay aa Celene ane Ele IEAI Lean wot TO AAP ep ay Sommarro 1 Yaar amar ae Tirer y THI Pivi pm ey Soy Tenia u Ehh erp wan VELSA Nett cca Tie Before service interrupt the mains power supply Open the cover of the electric box and disconnect the illumination sign s cable according to figure 3 Remove the plastic cover from each side figure 1 step 2 Unfasten the mounting screws to unmount the illumination sign figure 1 step 4 Unfasten the mounting screw of the bracket and remove it Unfasten the mounting screw with the cable holding accessory of the bracket and remove the bracket Unfasten the 3 screws without moving the marking panel Unfasten the 2 screws and remove the marking panel Slide out the led strip with a flat screwdriver Pull carefully the led strip by holding it from the two sides as shown in picture 40 Remove the used battery and place a new one with the same type A 939 HT with same cables and connector Push carefully the led strip by holding it from the two sides as shown in picture Push the led strip to face the edge of the plastic cover ATTENTION Don t apply force to the test button Refit the removed parts in steps 7 6 5 and 4 WARNING Use a maximum torque of 0 25Nm to tighten the screws step 6 7 and a maximum torque of 0 6Nm to tighten the screws step 4 5 Mount the illumination sign with the mounting screws f2. igure 1 step 4 Open the cover of the electric box and connect the illumination sign s cable figure 3 Close the cover and power the illumination sign 922503426 _09_018 MAINTAINED TO NON MAINTAINED SELECTION CAPABILITY Power on the device and press continuously the TEST button for 10 seconds until the led strip turns off Release the button and after a short emergency test the device operates as non maintained If you want to restore the previous condition maintained operation press continuously the TEST button for 10 seconds until the led strip lights Release the button and after a short emergency test the device operates as maintained illumination sign Troubleshooting 1 The illumination sign does not light when the TEST button is pressed 2 During the automatic 6month check the illumination sign does not light or has less autonomy than the nominal 3 The illumination sign does not light in normal operation 4 The illumination sign does not light during a mains failure The battery has lost it s energy Wait at least for 1 hour for the battery to be charged The battery is not connected Attach the battery s connector to the appropriate connector on the P C B The battery is inappropriate The battery must be replaced The battery has lost it s energy Wait at least for 24 hours for the battery to be fully charged The battery is inappropriate The battery must be replaced The illuminatio
3. ire L the neutral N and the ground GND To this terminal block is connected the power cable with a cross section of 1 5mm Install the electrical box in an appropriate area in the ceiling Install securely the 3 pole terminal block and perform the connection according to figure 3 The electrical box and the 3 pole terminal block are not included in the package Suspended ceiling mounting base Wall mounted installation o 342 using the special mounting brackets contained in the Recessed mounted installation package on suspended ceilings using the base type A 1020 220 240V AC 50 60Hz Page 2 from 6 922503426 09 018 Page 3 from 6 922503426 09 018 Page 4 from 6 Wall mounting 4 Place the mounting accessories in the wall and screw the mounting screws 1 Open the pre etched knock out and pass the cable thru 2 Place the single mounting plastic part _ gt 3 Place the cable holding accessory and mount it by f f tightening the screw with the included grommet 5 Follow the installation procedure in page 2 figure 2 and 3 Wall in bottom view 1 Open the pre etched knock out and pass the cable thru 2 Place the plastic part 3 Place the cable holding accessory and mount it by tightening the screw with the included grommet 4 Place the mounting accessories in the wall and tighten the mounting screw 5 Place the plastic cover and follow the installation procedure in page 2 fig
4. mounted in a clearly visible area and can either be hung on a ceiling or mounted on a wall depending on the requirements of the installation The package Page 1 from 6 3 years 1 year for the battery includes all the required materials for mounting on the wall or on the ceiling The pages 2 3 and 4 show us the mounting methods WARNING 1 Read carefully this instruction manual 2 The unit must be connected to a dedicated fused power line for example 16A rating 3 Every month an optical and emergency mode operation check should be carried out by pressing the TEST button 4 Every six months a full duration check should be carried out by disconnecting the mains power supply Count the autonomous duration of the luminaire and in case of no correspondence to stated emergency duration replace the battery 5 During long periods of inactive use i e 6 months disconnect the batteries from the units 6 Replaced batteries must not be thrown into trash bins They must be returned to special battery disposal points Do not incinerate NOTE LED Light Emitting Diode LABELING EXPLANATION X Self contained 1 Maintained A Including test device 180 3 hour duration 922503426_09_018 Mounting methods Mounting methods Ceiling mounting Ceiling mounting Hanging installation on suspended ceilings using the l Hanging installation special mounting brackets 1 Open the pre etched knock o
5. n sign is adjusted to operate as non maintained Choose if you must to turn the operation to maintained according to relative paragraph in page 6 The battery has lost it s energy Wait at least for 24 hours for the battery to be fully charged The battery is not connected Attach the battery s connector to the appropriate connector on the P C B The battery is inappropriate The battery must be replaced Package contents The package contains 1 The illumination sign 2 The instructions manual 3 Plastic bag with supporting materials Eco Light dimensions in mm a gt Page 5 from 6 MLD 34 365 a x 165 B 922503426_09_018 SAFETY amp JADE SECURITY MAINTAINED NON MAINTAINED OPTIONAL ILLUMINATION SIGNS WITH WHITE LEDs TECHNICAL CHARACTERISTICS MLD 34D w Mains voltage 220 240V AC 50 60Hz Maximum power consumption 8 VA Batteries Ni Cd 3 6V 1Ah Battery protection Overcharging and full discharging protection Recharging time 24h Minimum emergency duration 3h Light source intensity Mains Emerg 100Im 80Im Degrees of cover protection IP 40 Produced in accordance with EN 60598 1 EN 60598 2 22 EN 1838 Operation temperature range 0 to 40 C Relative humidity up to 95 External panel s dimensions 340x170mm External dimensions 365x25x225mm Ty
6. pical weight 870gr Guarantee Operation instructions These new sign illumination luminaries use a new technology friendly to the environment with high illuminated L E D s L E D technology has very low power consumption The edge illumination sign is used as a maintained emergency lighting with indications symbols In this type of marking panels the PVC overlay is mounted on the marking panel with 4 plastic screws and it can be changed by change the PVC overlay in accordance with the marking code Each model combines modern aesthetics together with functionality The exit illumination signs are used in every public area where clear direction and good appearance are important NON MAINTAINED OPERATION By default the illumination sign operates as maintained The device has a possibility to operate as non maintained To change the maintained to non maintained operation follow the relative instructions in page 6 All models must be permanently connected to the mains power supply as shown on page 2 The legend is screened on to a clear acrylic sheet which has the marking on the marking panel with the light that comes from the top of the luminaire and diffracts giving light to the marking panel The luminary has an indication CHARGE for the charging of the battery and a TEST button to TEST the emergency circuit and the LEDs for good operation only when the luminary is plugged in to mains power supply The unit must be
7. uded mounting screws 4 Place the mounting accessories in the 5 Refit the plastic cover on each side wall and tighten the mounting screw 6 Attention Interrupt the mains power supply 1 Place the plastic part 7 For the installation of the electrical box you may need to open holes in the ceiling and at it s cable j entrances for the entrance of the power and illumination sign s cables Place the electrical box on the side of the illumination sign at a distance of 30cm from it Figure 2 8 After mounted the electrical box open the cover and perform the electrical connection according to Figure 3 No preparation is required stripping for the cable After the connection close the cover of the box 9 Power the illumination sign 10 Check the illumination sign s operation Flag mounted installation on a wall using the special mounting bracket contained in the package 2 Tighten the screw 3 Pass the cable in the canal Electrical box Figure 2 4 Place the plastic cover after the opening of the pre etched Not included knock out to pass the wires 6 Follow the installation procedure in page 2 figure 2 and 3 k 30cm Use a certified electrical box 250V AC IP40 to perform the electrical connection with minimum internal space 35x35x25mm to install the 3 pole terminal block In this box install a certified 3 pole terminal block 250V AC 16A 2 5mm providing terminals to connect the live w
8. ure 2 and 3 922503426 09 018
9. ut and pass using the special contained in the package the cable thru mounting sets Hanging installation on 2 Place the plastic part suspended ceilings using the Place the cable holding accessory and mount it by special mounting brackets tightening the screw with the included grommet ATTENTION 4 Follow the installation procedure in page 2 figure 1 2 and 3 All metall parts must be connected to ground Alternative mounting method gt 5 Hang the luminaire and adjust the metall cover by the screw of the metall ring 4 Pass the cable thru the nut and the extension pipe and tighten it f Extension ability In recess mounting in suspended ceiling or in external ceiling mounting we can use the A 1022 extension set 20 cm after request 1 Open the pre etched knock out and pass the cable thru 2 Place the plastic part 3 Tighten the screw 6 Place the plastic cover and follow the installation procedure in page 2 figure 2 and 3 1 Attention Choose the installation area to insure that the mounting surface is appropriate for the sS2 installation of the illumination sign eee a 2 Remove the plastic cover from each side MLD 34 S 28cm 3 Measure the space S according to the illumination sign s type and drill the appropriate holes in the ceiling for the installation of the included mounting plugs No 6 4 Place the mounting plugs No 6 and mount the sign by tightening the incl
Download Pdf Manuals
Related Search