Installation Manual
Contents
1. and you have issues with either short or long ranging a Walk Tester will assist greatly in correct alignment and performance Each Premier Elite Orbit has been fitted with and infra red LED emitter When activation occurs the transmitter sends a signal This signal is then received by the Walk Tester and a very bright white LED on the Walk Tester flashes also a piezo speaker sounds Under normal situations both the LED and the sounder can be seen and heard up to 50 meters S Z N LED _ YON Z e Sounder e o AS AS Blue LED Premier Elite Orbit PCB WalkTester Holder WalkTester The Walk Tester comes with a mounting bracket holder First fit a PP3 battery into the Walk Tester battery compartment This is done by removing the battery compartment cover Please ensure that the on off switch on the Walk Tester is set to the off position while connecting the battery When fitted close the battery compartment and the Walk Tester is ready for use gt S W Removing the Battery Cover 7 INS483 2 7 Using the Walk Tester Remove the cover from the Premier Elite Orbit housing by loosening the locking screw at the bottom of the detector This will allow access to the programming button shown in Fig 11 and to also to show the location of the blue IR emitting LED Place the Premier Elite Orbit into walk test mode by pressing2. OFF Pressing the program button once will enable the walk test LED for 5 minutes THE FRONT COVER MUST BE FITTED WHEN WALK TESTING FACTORY SETTINGS ARE 1 RANGE 30 METRES 2 PULSE COUNT 1 3 LED OFF When enabled the Premier Elite Orbit DT has three LED indicators Green Microwave detection Red Both PIRs detection Blue Alarm output both PIRs and microwave detection mk INS483 2 1 Mounting the Unit During installation the electronics must be protected against water as trapped moisture can affect or damage the unit BoP ls for Tamper Cup o e Cable Holes ate als Da 5S ieee Fixing Holes 1 Using the template provided drill the wall to accept the two fixing screws the cable entry and the tamper cup if used See fig 1 and 2 Note We recommend using the tamper cup on uneven wall surfaces 2 Remove the cover assembly by loosening the locking screw using the allen key provided The cover hinges from the top and lifts out of the location slot Tamper Tamper Foot 77 Cup T R N WC lt INS483 2 See fig 3 3 Feed standard 8 core alarm cable into the cable entry bare the wires and connect to the removable terminal block as shown in fig 7 Screw the unit to the wall ensuring that the tamper pin is correctly located and that the tamper microswitch is closed See fig 4 an
3. RANGE MAXIMUM MODULE TILT 45 DEGREE 15 10 5 0 gt 5 10 15 5 10 15 20 25 30 C gt MICROWAVE Premier Elite Orbit DT only 2 L_L_ PIR Beam Pattern set to minimum range Masking top section of lens will reduce range to 6 metres INS483 2 4 Programming The user can individually program a number of configurable settings as illustrated in the programming chart Factory settings are shown as shaded boxes Changes to the existing settings can easily be made To reset the factory settings simply remove power form the detector press and hold the program button fig 10 whilst temporarily applying power to the detector either before installation with a PP3 battery or by applying 12 Volts to the unit on site LED Program Button SETTING PROGRAMMING CHART Cs To change any of the Premier Elite Orbit settings 1 Press the program button as shown in fig 10 for the number of the Option to be changed i e once for range twice for pulse count three times for LED 2 Wait four seconds until the blue LED indicator goes off 3 The indicator will then flash out the existing setting 4 To change the setting for that option immediately within 2 seconds press the button the number of times required for the new setting 5 The indicator blinks twice and the changes are stored OPTIONS Any alterations made to the Premier Elite Orbit settings are stored in th
4. a maximum of 24Vacjoc 50 mA ACCESSORIES Texecom is able to supply the following accessories to aid installations Pole mount bracket available on request JAH 0001 Premier Elite Orbit Walk Tester INS483 2 8 9 Approved External Microwave Frequencies Premier Elite Orbit DT 9 35GHz 9 90GHz 10 525GHz 10 587GHz Albania Argentina Australia Austria Belgium Brazil Croatia Czech Republic Denmark France Germany Greece Holland Hungary Iceland Indonesia Italy Latvia Lithuania Malta Norway Portugal Poland Russia Slovakia South Africa Spain Taiwan Thailand U A E UK Ukraine USA INS483 2 10 Technical Specifications Premier Elite Orbit DT Detection Area Programmable between 10 amp 30 metres Coverage 10 70 degrees detection angle 30 m x 30 m coverage max Adjustment 180 degree pan 90 degree tilt Fresnel Lens 28 zones for each pyro pair which can be masked with the curtain sliders Customised Optics Double silicon shielded quad element eliminates 50 000 lux of white light Microwave Module Frequencies 9 35GHz 9 90GHz 10 525GHz 10 587GHz see page 10 Outputs Silent solid state magnetically immune Volt free relay signal contact 24Vacjoc 50mA with an integral 25R series resistor Alarm time 5
5. seconds Volt free relay signal contact 24Vacjoc 50mA with an integral 25R series No 1 N OPEN Me CEOSED resistor Alarm time 5 seconds Power Input 9 to 15 Voc Current 15mA 12V nominal Pulse Count 1 2 Temp Compensation Digital sensitivity adjustment Control Digital microprocessor non volatile memory Walk Test Output test mode with LED indication Operating Temp 20 to 55 C Conformally coated electronics for increased stability Housing ABS Protection Rating IP 55 Dimensions 141 x 165 5 x 109 mm Weight 300 grams Mounting Height Variable up to 6 metres optimum height 3 metres Cable lt 200m Utilising all three outputs incl tamper 8 core 7 0 2mm Cable lt 500m Utilising all three outputs incl tamper 8 core 16 0 2mm Regulatory Information Supplier Texecom Ltd St Crispin Way Haslingden Lancashire BB4 4PW UK Weee Directive 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of fe as unsorted municipal waste in the European Union For proper recycling return this product to n your local supplier upon the purchase of equivalent new equipment or dispose of it at designated S Oo collection points For more information see www recyclethis info british security industry association RoHs Directive 2002 95 EC RoHS Compliant Hereby Texecom declares that this device does not contain lead
6. shutters to reduce the detection angle An additional set of curtains is provided should the beam pattern need to be narrowed even further e g if the minimum detection angle of 10 degrees is required The curtains are fitted to the pan and tilt module as indicated in fig 8 below Each section of the detector s lens gives a coverage pattern of approximately 10 degrees See fig 8 DY O 5 D yy Q dl Y j yy Oy oy A O INS483 2 3 Multibeam Alignment amp Masking When mounting higher than boundary fences rotate the module and mask off any beams either vertically or horizontally that fall outside the area being covered Use portions of the self adhesive silver mask supplied to the rear smooth side of the lens as shown in the diagrams below Always replace the lens the correct way up to ensure exact beam pattern coverage the top of the Fresnel lens is marked TOP See fig 9 Page 4 MULTIBEAM OPTIMUM HEIGHT 3 METRES RANGE MAXIMUM MODULE TILT 0 DEGREE MULTIBEAM HEIGHT 6 METRES RANGE MAXIMUM MODULE TILT 9 DEGREE PET IMMUNITY HEIGHT 1 5 METRES RANGE MAXIMUM MODULE TILT 2 DEGREE LONG RANGE 20 METRE SECTION aaao LO l HH si MASK THIS SECTION OFF FOR PET ALLEY APPLICATIONS UP TO 30 METRES CURTAIN COVERAGE MASK THIS SECTION OFF FOR CURTAIN COVERAGE APPLICATIONS It HEIGHT 6 METRES
7. Installation Manual Premier Elite Orbit QD DT INS483 2 CE Texecom Designed to Perform Introduction e ACCTV event trigger utilising two independent passive infrared detectors combined in a T05 package and a microwave sensor Both sensors have to trigger before the detector signals an alarm This high precision very reliable presence detector has been designed for use within CCTV installations Programmable parameters include a pulse count feature and a choice of detection ranges from 10 to 30 metres e The integral dual axis tilt sensor allows 180 of pan and 90 tilt This increases the speed of the outdoor installation and provides incredibly accurate aiming of the detection pattern The electronics module is acrylic coated for additional component stability It is encased in an ABS housing with a UV stabilised translucent front cover ensuring the sensor is impervious to and unaffected by weather conditions Additionally the combination of precision electronics digital white light filter and double shielding eliminates false alarms from the sun and other visible light sources e The Premier Elite Orbit design gives a neat and professional appearance with no visible indication of the orientation of the detector head and totally hides the wiring Quick Installation Guide Apply supply voltage to the unit the blue LED flashes 3 times The detector takes approximately 2 3 minutes to settle The walk test LED is factory set to
8. d 5 To aid installation two spare tamper feet are provided One is 1mm longer and the other is 2mm longer than the tamper foot originally fitted The tamper foot is a push fit and can be removed by carefully pulling it from the pin See fig 2 4 Always ensure when replacing the electronics module that the LED is facing forward so as to ensure correct alignment of the beam pattern Refer to section titled Multibeam Alignment amp Masking 5 When the detector has been aligned to suit the installation replace the front cover and lock as shown See fig 6 2 Connecting the Unit Q Tamper Connection Alternative Route 2 Route 7 Route 3 Not Recommended Normally Closed Tamper Circuit Front amp Rear Alarm Connection OV Supply 12Voc Supply Alarm Output 2 Multiplexer PTZ Dome DVR etc Alarm Output 1 Multiplexer PTZ Dome N Closed DVR etc 3 INS483 2 3 Multibeam Alignment amp Masking The multifunction lens fitted to the Premier Elite Orbit detector produces 7 long range beams and 7 medium to short range curtain beams Movement across the beams produces the best response and range whilst movement towards the detector will be less responsive The unit detects the changes in heat and movement in the beam pattern therefore items such as trees shrubs ponds boiler flues and animals should be considered when positioning the detector The detector module is fitted with two sliding
9. e detector s non volatile memory EXAMPLE To change the LED Setting from OFF to ON 1 Press the program button three times and release the button 2 Wait until the indicator goes off 3 The indicator will now flash once 4 Press the program button twice and release the button 5 The indicator flashes twice showing that the option has been stored and the detector returns to normal operation INS483 2 6 5 Walk Test The range of the detector increases without the front protective cover Therefore the front cover must be fitted to establish the correct beam pattern alignment and when testing the outputs Use the program table on page 5 to adjust the range as necessary and pan and tilt the lens module over the field of view to obtain the correct coverage area When the program button is pressed momentarily the blue indicator lights and pulse count 1 is automatically selected The unit can then be aligned The blue indicator will light on the Premier Elite Orbit every time a detection takes place This test mode will automatically cancel five minutes after last detection Alternatively remove the power and then re apply 6 Walk Tester The Premier Elite Orbit Walk Tester is an installation tool that will help the installer set up the detector on site Considerable time will be saved in the setup procedure when using the Walk Tester and it s use is highly recommended If you have difficulty in aligning the detector
10. mercury cadmium hexavalent chromium polybrominated biphenyls PBB or polybrominated depheny ethers PBDE in more than the percentage specified by EU directive 2002 95 EC except exemptions stated in EU directive 2002 95 EC annex CE Directive 2004 108 EC CE directive Hereby Texecom declares that this device is in compliance with the UKAS QUALITY essential requirements and other relevant provisions of Directive 2004 108 EC MANAGEMENT Certificate Number FM 35285 Maintenance Test yearly by the installer Warranty 2 year replacement warranty MAD E IN E NG LAN D The Premier Elite Orbit detector is not a complete alarm system but only its part Therefore Texecom does not accept any responsibility or liability for any damage that is claimed to be a result of an incorrect m 2 functioning of the Premier Elite Orbit detector Texecom reserves the right to change the specification The Premier Elite Orbit detector Is without a prior notice protected by UK amp International Designs Premier is a Trademark of Texecom Ltd INS483 2 10 11 Technical Specifications Premier Elite Orbit QD Detection Area Programmable between 10 amp 30 metres Coverage 10 70 degrees detection angle 30 m x 30 m coverage max Adjustment 180 degree pan 90 degree tilt Fresnel Lens 28 zones for each pyro pair which can be masked with the curtain sliders Customised Optics Outputs Double silicon
11. shielded quad element eliminates 50 000 lux of white light Silent solid state magnetically immune No 1 N OPEN Volt free relay signal contact 24Vacjoc 50mA with an integral 25R series resistor Alarm time 5 seconds No 2 N CLOSED Volt free relay signal contact 24Vacjoc 50mA with an integral 25R series resistor Alarm time 5 seconds Power Input 9 to 15 Voc Current 8mA 12V nominal Pulse Count 1 2 Temp Compensation Digital sensitivity adjustment Control Digital microprocessor non volatile memory Walk Test Output test mode with LED indication Operating Temp 20 to 55 C Conformally coated electronics for increased stability Housing ABS Protection Rating PS5 Dimensions 141 x 165 5 x 109 mm Weight 275 grams Mounting Height Variable up to 6 metres optimum height 3 metres Cable lt 200m Utilising all three outputs incl tamper 8 core 7 0 2mm Cable lt 500m Utilising all three outputs incl tamper 8 core 16 0 2mm Texecom Designed to Perform Texecom Limited Bradwood Court St Crispin Way Haslingden Lancashire BB4 4PW England Technical Support UK Customers Tel 08456 300 600 Calls charged at 3 36 pence per minute from a BT landline Calls from other networks may vary International Customers Tel 44 1278 686197 Email techsupport texe com Texecom Limited 2011 INS483 2
12. the programme button once Fig 11 The Premier Elite Orbit s clear LED will then flash out its current settings Wait for the flashing sequence to finish The Premier Elite Orbit is now in walk test mode and will remain in that state for five minutes after the last detection whereafter it will revert to normal mode The walk test can be cancelled at anytime by pressing the programme button twice Replace the Premier Elite Orbit cover and place the Walk Tester in the metal holder Slightly loosen the stainless steel screw on the bottom of the Premier Elite Orbit just enough so that the drilled tab on the Walk Tester bracket can slide around the screw thread Then gently tighten the screw to hold the Walk Tester and holder in place Turn the Walk Tester on The Walk Tester will illuminate and sound every time the Premier Elite Orbit is activated When finished testing turn off the Walk Tester and remove it and the holder from the Premier Elite Orbit Tighten the screw on the base of the Premier Elite Orbit The external detector is now ready 8 Option Definitions PULSE COUNT This is the number of times the unit has to detect on both of its sensors before signalling an output LED MONITOR LED Off LED disabled LED On LED signals a detection N OPEN amp N CLOSED These are magnetically immune volt free relay contacts used to trigger alarm inputs on connected equipment The contacts are rated at
Download Pdf Manuals
Related Search