Biological Microscope BMS C1 series User Manual
Contents
1. Ra 4 Right Coarse Focus Knob Main Switch Tension Adjustment Collar Lateral Adjustment Knob 3 2 Operation 3241 Adjusting the Illumination Fig 20 21 Connect the power turn on the main switch figure 15 to on Turning the brightness adjustment knob anti clockwise the voltage raise and the brightness strengthen turning it clockwise the voltage decline and the brightness weaken Using the lamp in a low voltage condition will prolong the use life 8 3 2 Placing Specimen Fig 22 1 Place the slide on the mechanical stage Use the stage clips to clamp the slide gently 2 Turn the portrait and lateral adjustment knob of the mechanical ruler move the specimen onto the required position Be careful when changing the objective If you finish the observation with the short working distance objective and want to change another one be careful of not letting the objective touch the specimen 31313 Focusing Fig 23 1 Use the 10xobjective focus to avoid the objective touch with the specimen you should raise the mechanical stage at first let the specimen close to the objective then slowly separating them to focus The operator can converse turn the coarse focus knob to get the specimen down and search images in the 10xocular simultaneously then use the fine knob to focus At this moment you can replace2. 1 Before linking the cable make sure the switch is cut off 2 Insert the electronic plug in the socket safely 3 Insert on Use the cable wire supplied by BMS company when destroyed make the choice of same type The machine adopt the wide voltage can work under the voltage of 230V 50Hz 2 2 6 change the fuse picture9 amp 10 Before change the fuse make sure that the switch is cut off swing out the change new fuse then swing back into the 228 install amp change the lamp C picture 11 12 13 Please use the designated 6V 20w halogen lamp 1 Pull out the condenser set 1 1 Use the pledge wrap the lamp put the lamp pin into the socket 3 2 Change the lamp during usage Make sure the switch is cut off amp all Picture 11 parts around lamp are cool down Insert the lamp carefully do not touch the lamp with finger amp strong force Insert the condenser opposite direction as picture picture 12 Picture 13 3 1 adjustment system installing illustration picture No 14 15 interpupillary distance showing condenser adjustment knob Eye viewing adjust ring 7 locking knob left fine focus knob light adjusting switch left coarse focus knob Picture 14 Right Fine Focus Knob RES EX Portrait Adjustment Knob
3. I Optical Part SOLUTION Adjust it into the located position Adjusting it to center Wipe up Wipe up Wipe up the condenser locking Adjust the position of Loose bolt condenser Screw down the locking bolt Cover the slip Use standard cover slip Thickness 0 17mm Reverse back Wipe up Wipe up Use oil Remove oil Use the appointed oil Properly make it smaller Wipe up Properly make it larger Adjust the position Reinstall the condenser and adjust the center carefully by using the condenser adjusting bolt Turn it into the required position Reinforce it reliably age moved focusing The image takes the yellow slightly The bright degree is not enough The specimen is floating on the stage The nosepiece is not in the located position Not use the color filter The opening of Aperture diaphragm is too small Condenser position is too low Stains on the lens Condenser Objective Eyepiece 14 Reinforce it reliably Turn it into the required position Use the blue filter Properly make it larger Adjust the position Wipe up II Mechanical Part PROBLEM REASON FOR PROBLEM SOLUTION 1 Can t focus when use Reverse back are Slice put reversed I high magnification Using standard cover slice bas Cover slice is too thick i objective Thickness 0 17 mm 2 Touch the slice when switch the Reverse back p S
4. 55 75mm Eyepiece View field line 18mm Nosepiece Forward Quadruple Nosepiece Objective Achromatic 4X 10X 40X 100X Focus System Focus 0 002mm Coarse amp fine focus range 23mm Coaxial Coarse and Fine Focusing System Sensitivity and Graduation of Fine Condenser Stage Abel NA 1 25 Double layer mechanical stage area 140 X 140mm movement range 75 X 50mm Lamp House halogen lamp 6V 20W Eyepiece amp Objective 1 Objective Numerical Value AN AIT Thickness of Working Working Magnification Aperture Focus mm Cover Slip mm Distance mm Mode Diaphragm N A 4x 0 10 0 17 31 05 37 5 Dry 10X 0 25 0 17 17 18 7 316 Dry 40 X 0 65 0 17 4 65 0 632 Dry 100 X 1 25 0 17 2 906 0 198 Oil 2 Eyepiece Sort Magnification Focus mm View field line mm Plan Eyepiece 10x 24 95 018 3 Total magnification with Objective plus Eyepiece Objective 10X 10 X 10x 10x Eyepiece 4X 10X 40 X 100 X Total magnification 40 X 100 X 400 X 1000 X 12 Name of Standard Specifications Amount Components Equipped Main Frame 1 Body Double Layer Mechanical Stage 1 Condenser Bracket 1 O Observation System Compensation Free binocular Head 1 O Condenser N 1 25 Abbe Condenser 1 O Nosepiece Quadruple Nosepiece 1 O 6V 20W Halogen Lamp 1 O Lamp house Spare Lamp 2 O Spare Fu
5. other magnification objectives safely and focus without the risk of destroying the specimen If you need to fix the stage on a vertical position to make the observation become more convenience take use of the locking set 3 3 4 Adjusting the Condenser Fig 24 Turn the condenser focus knob to shift the condenser It needs to raise the condenser when using the high magnification objective and to decline when using the low magnification one x The center of the condenser and the light axes of the objective are coaxial It has been adjusted before leaving factory so the user needn t to adjust them by self x The highest position of the condenser has been adjusted too It also needn t any user s operation 3 3 5 Adjusting the Aperture Diaphragm Fig 25 Turn the Aperture Diaphragm Lever to adjust the aperture size Aperture Diaphragm is designed for adjusting the aperture size not for adjusting brightness Generally reducing the diaphragm opening to 70 80 of the N A value of the respective objective will provide an image of acceptable quality If you want to observe the image of the aperture diaphragm remove one eyepiece and look through the tube You will see a dark circle encroaching on the bottom of the tube 33 Adjusting the Interpupillar Distance Fig 26 The interpupillar distance range 55mm 75mm When observing with two eye
6. Biological Microscope BMS CI series User Manual This manual is written for biological microscope BMS CI For safety exerting best performance of the instrument and making you familiar with the instrument entirely we strongly recommended that you carefully read this manual before using the microscope Use Notices 1 Name of Components Cee cre ccc ccs cee cee cee cee cee cee eee cee ces cee ces cecces 1 2 Installation PERCEPT E eer ere err ere err ere err err er rere eer eee eee eee eee ee ee ee ee 2 2 1 Installing Illustration CELL eee eee eee eee eee eee EEE EEE ETES STE STE SEE ETES TESTS TEE TEE EE EEE ET 2 2 2 Installing Steps nn nn nn sn ere ere eee eee eee ere reer errr err err errr rr err err err er rere 3 3 Adjustment amp Operation Cee cre ccc cee ccc cee cee cee cee cee cee cee ces cee cescecces 7 3 1 Adjustment System Installing Illustration Pee rec ccc ccc ccc ccc ccs ccc ccc cee ces ccccce 7 3 2 Operation eee eee ee eee eee eee ee ere eee Creer rere errr rere err errr rr err err err er rere 9 4 Technical Specifications Coe cee ccr eve cee ccs cee cee EEE CELLES CECI EEE EEE ELITE 12 5 Configuration Table eee eee rere er rere err ere ere eee eee ee ee ee eee ee ee ee ee 13 6 Trouble Shooting Coe cee cee eee eee eee eee eee eee ees ees ees ceseeseeeceseeecescesere 13 I Safety note 1 Carefully open the box avoid the accessories like lens dropping to ground and being damaged 2 Do keep the instrument out of direct sunli
7. bjective Cable Wire 2 Installing Setps Picture 1 O D Picture 4 220 Install the binocular viewing head picture No 1 2 Insert the binocular viewing head in the head of the body turn to the right place then fix up it by bolts 2 2 2 install the eyepiece picture No 3 4 Insert the eyepiece in the eyepiece tube till end No 4 picture shows the station after the installing 2230223 install the objective picture No 5 6 NaN 1 Adjust the coarse amp fine focus knob till the mechanical stage to Picture 5 the low limited place 2 Screw down the objective to nosepiece one by one Dr Clean the objective frequently At first use the 10X objective to looking for image then change another one Turn the objective till hear the kaca sound make sure the objective enter the objective center 2 2 4 Install the filter picture 7 1 Swing out the condenser holder Picture 7 2 Put the filter in the holder Then swing the holder in Picture 8 Picture 9 z le Picture 10 225iLink cable wire picture NO 8 9 10 Do not push strong force on the cable wire because the bending cable is easily be destroyed
8. ght high temperature or humidity dusty and easy shaking environment Make sure the stage is smooth horizontal and firm enough 3 When moving the instrument please use two hands to grip with the two sides of the microscope body 4 If the bacterium solution or the water splash to the stage objective or viewing tube pull out the power cord at once and wipe up the microscope Otherwise the instrument will be damaged 5 When running the lamp house and nearby parts will be very hot Please ensure there is enough cooling room for them 6 Make sure the instrument is earthed to avoid lighting strike 7 For safety be sure the main switch is in O off state before replace the halogen lamp or the fuse then cut off the power and do the operation after the lamp bulb and the lamp house completely cool 8 Check the input voltage be sure the input voltage which signed in the back of the microscope is consistent with the power supply voltage or it will bring a serious damage to the instrument 9 Use the factory supplied power cord please II Maintenance 1 All the lenses have been well checked and adjusted It is forbidden to disassemble them yourself 2 The nosepiece and coarse fine focus unit have a compact and precise frame please don t disassemble them as possible as you can 3 Keep the instrument clean wipe dust regularly and be attention to avoid contaminating the optical elements especially 4 The contaminations o
9. lice put reversed objective from low f Using standard cover slice BR j Cover slice is too thick magnification to Thickness 0 17 mm high one 3 The specimen move The slice holder not nip the Make it firmly not flowing slice firmly 4 Two eyes image not The interpupillar distance is not Adjust the interpupillar in superposition correct distance correctly Adjust the diopter according The diopter is not right your sight 5 The eyes i 6 The bright degree is not uncomfortable properly Adjust the voltage of bulb III Electric Part PROBLEM REASON FOR PROBLEM SOLUTION Check the power cord and No power supply connect them exactly The lamp can t light the installation of the bulb is wrong Install the bulb correctly The bulb burn out Change a new bulb Use a appointed lamp If the The bulb burn out Not use a appointed lamp circumstance still not change in a high frequency High voltage please contact the maintenance part The rightness degree Not use a appointed lamp use a appointed lamp is not enough Low voltage Turn up the voltage The bulb is going to spoil Change the bulb The light glimpse The power cord have a poor Check the power cord and contact connect them exactly
10. n the prism as finger mark and oil could be gently wiped with a piece of soft cloth or tissue paper gauze which has been immersed in pure alcohol or xylene note that the alcohol and the xylene are all burned easily do not let them near the fire and use them in a drafty room as possible as you can 5 Don t use organic solvent to wipe the non optical elements when you need to clean use the soft detergent please 6 When using if the microscope is splash by liquid cut off the power at once and wipe up the moisture Do not disassemble any parts of the microscope That will affect the function or decline the performance of the microscope Place the instrument in a cool dry position After using the microscope remember to cover it with dust helmet Do wait for the lamp house cooling completely before cover Binocular viewing head Eyepiece 99 gy Nosepiece Objective 40 D 160 by 2 1 Installing Illustration The following shows the installing order of the spare parts The number express the installing process before the installing make sure there is no dust and stain on the spare parts No marks by outside force on the surface of the spare parts or glass Keeping the hexagon spanner well when change the spare parts you will use it Binocular Viewing Head 10x Objective 0 w tu A 77 um Gr es O
11. s hold on the left and right prism holder turn around the axis adjust the interpupillar distance until the left and right fields Fig 26 of view coincide completely 10 31333 Adjusting the Diopter Fig 27 Observe the right ocular tube with your right eye Turn the Coarse amp Fine Focus Knob to focus the specimen Observe the left ocular tube with your left eye If not in focus just adjust the Diopter Ring to make it in focus the range of Diopter Ring is 5 as the value align the reticle of the ring 27 339 Adjusting the Tension Adjustment Collar Fig 28 The tightness of the tension adjustment collar has adjusted before leaving factory if finding it s loosing the mechanical stage drop itself because of deadweight please turning the tension adjustment collar until the tightness is in order Turn it along the direction show in the picture the Coarse Focus Knob will become tighter Turn anti direction will become loosen a If the mechanical stage drop itself or even lose focus just after adjusting the fine focus knob V Mean the tightness of the Coarse Focus Knob is too low You should turn the tension adjustment collar along the direction show in the picture to make it tighter Fig 28 11 Main specifications Mechanism Tube 160mm Length Viewing Head Compensation Free Head Inclined at 30 Interpupillar distance
12. se BGX 1 20 0 5A 2 O 2 Eyepiece Plan Eyepiece 10X 2 O Achromatic Objective 4X 1 O Achromatic Objective 10X 1 O Objective Achromatic Objective 40X 1 O Achromatic Objective 100X Oil i Spring Bright Field Condenser with Condenser 1 O Changeable Raster Filter Baby Blue Green 1 O 13 PROBLEMS REASON FOR PROBLEMS The edge of the field of view has the brightness is shadow or asymmetry Stains in View Field Low image quality Low resolution low contrast One side of image is dark The nosepiece is not in the located position The filament Imaging not in center Stains on the lens Condenser Objective Eyepiece Stains on the lens Condenser Objective Eyepiece Stains on the specimen The Condenser position is too low No cover slip on the specimen The cover slip is too thick or too thin The specimen is reversed The dry objective is stained with oil Especially 40X Stains on the lens Condenser Objective Eyepiece The oil objective is not in oil There is air bubble in oil Not use the appointed oil The opening of Aperture diaphragm is too large Stains on the incidence lens in the binocular drawtube The opening of Aperture diaphragm is too small Condenser position is too low The condenser is not in center of the view field or the condenser is inclined The nosepiece is not in the located position The specimen is floating on the stage
Download Pdf Manuals
Related Search