Home

User's Guide - Security Point

1. 8 Input netconfig command after bash prompt and press Enter key Then you can see following network setup values bash netconfig Current configuation IP Address 10 20 30 40 Network Mask 255 255 255 0 Gateway 10 10 1 1 Enter IP Address 9 Input new IP address Network Mask and Gateway values to be assigned to FlexWATCH server After this press y to apply the new network configuration 29 Seyeon Tech Co Ltd Network Video Server User s Manual Enter IP Address 70 10 213 22 Enter Network Mask 255 255 0 0 Enter Gateway 10 10 1 1 Entered network configuation IP Address 10 10 213 22 Network Mask 255 255 0 0 Gateway 10 10 1 1 Do you wish to apply your new network configuration y n q y 10 If following messages come up on your screen with bash prompt the new network configuration has successfully applied Your network configuration was changed Shutting down interface ethO OK Shutting down interface ppp1 OK Shutting down interface ppp2 OK Setting network parameters OK Bringing up interface lo OK Bringing up interface ethO eth0 Setting half duplex based on auto negotiated partner ability 0000 OK Bringing up interface ppp1 OK Your new network configuration was applied bash 11 To check whether your Network configuration is correctly applied or not press ifconfig command after
2. Total Pre alarm buffer size Alarm buffering service size 70 Oo sl Apply Notice System Reboot is required ance memory assignment is changed o gt Non buffering Service This configuration is for advanced services which do not need Pre Post alarm video buffering space Total Buffer size This shows the maxim system memory for alarm buffering services The number of maximum total buffer frame for respective services can be decided by following formula Total buffer size file size number of total buffer frame e g 500 KB 10KB 500 frames which is possible total buffer size Total Pre alarm Buffer size This is to assign memory space for the services that Pre Alarm video buffer is required such as e mail and FTP Edge service and Alarm buffering service Once it is configured DE 79 Seyeon Tech Co Ltd Network Video Server User s Manual pre alarm buffer size for respective camera can be done within this assigned memory Note that Pre Alarm buffer for even Alarm buffering service can be done within this memory size Thus you need to be careful to assign memory for this service The rest of memory after setting up Alarm buffer service memory capacity will be assigned to this service configuration Alarm Buffering Service size To assign memory for Alarm buffering service to save pre post alarm image in the system memory so that user can playback stored video in the system through web browser or downloa
3. M ZE Application idea If server is connected to dynamic IP or Private network and you want to continuously send image to FTP server please use Overwrite function in the Periodic FTP service 5 Alarm Buffering Service Pre Post alarm image can be stored in the system memory so that user can remotely connect the server and playback stored image at any time 5 1 Alarm Buffering Service Configuration 1 Go to Advance Service menu in the service configuration mode and set up system memory assignment for Alarm Buffer service 2 Select Buffering Service option and check whether Pre Alarm buffer size is already assigned Otherwise assign pre alarm butter size 3 Select Alarm Buffer Service from the listed option SSS eee 94 Seyeon Tech Co Ltd Network Video Server User s Manual 4 Enable the Alarm buffering service Alarm Buffering Service Configuration Service Enable Disable Back cave 5 Select the camera and assign Pre post alarm image frames Alarm Buffering Service Configuration at Camera Pre alarm Buffer Size CDU iframes s gt Check video buffer Delay between pre alarm images JU msec an Check video buffer Number of pre alarm images en i frames Number of post alarm images pp frames Delay between post alarm images 110 unit unit 10 msec Back Save 6 Click Save button to memorize your new setting in the system 7 Click the Condition menu and set up alarm buffering
4. server 4 Select Passive or Active Mode depends on the network situation with NDVR server 48 Seyeon Tech Co Ltd Network Video Server User s Manual 5 Once Active mode is selected type in IP address of NDVR server amp Note NVCP port should be open to communicate with NDVR Server when the FlexWATCH server IS programmed to communication with NDVR server Tx Module Registration Tx Module o Enable Disable Connection Type Passive ActivelStatic IP IP Address NvCH Port iaeetination Re Hore 50100 Default 50100 up to 65535 VS Module ID o Back H Save Notice e IP address IP address of Rx Server e WVCP Port TCP port number of Rs server through which video will be transmitted to Rx server e Y5 Module ID Module ID of Rs Server D is default ID for all NWR servers Unless Different ID is specified by Rx server Following is recommended setting guide for TX and RX module for FlexWATCH server and NDVR depending on the network environment Mode Network environment Mode Network environment WAN Network Global Static Active Mode LAN network Private LAN Network Private LAN Network Private Active Mode LAN Network Private WAN network Global Static Active Mode WAN Network Global Static WAN Network Global Static ES eS 49 Seyeon Tech Co Ltd Network Video Server User s Manual Network Configuration Network configuration mode provides interface for
5. server acts as a Server and receives a call from remote user Tel User ID and User password ISP phone number and user account for Internet connection to ISP Default Route Enable this option When Dial out option is selected ZS Note If you use external modem we recommend 3COM U S Robotics 56K external modem for better performance although FlexWATCH server is designed to flexibly work with different external modem from different manufacturer If you are to use different external modem from different manufacturer we recommend you to contact your distributor or contact sales flexwatch com to choose compatible modem 4 3 2 Dial Out through Media specific device Dial out can be done through specific media which is not standard PSTN such as CDMA SS SSIS SEES 5G Seyeon Tech Co Ltd Network Video Server User s Manual modem GSM or GPRS Modem or any type of wireless modem This mode is not for general users Thus if you need to connect special modem device please contact your vendor or manufacturer for more information sales flexwatch com 4 4 Dial in Configuration Dial in is to allow client PC to call into the server and get live video through PSTN line Overall configuration is very similar to that of Dial out configuration But much more simple than Dial out 1 Go to WAN PPP Modem etc menu in the Network configuration mode 2 Select PPP Server This is to authenticate incoming call to serve
6. and Event condition window become inactive Schedule Only To active any selected option by scheduling If you select this criteria Event condition 84 Seyeon Tech Co Ltd Network Video Server User s Manual setup window become inactive Event Only To activate any selected option by Event only Sensor status change Is recognized as Event Schedule and Event To active any selected action when Event is triggered for the specified time period only If Event is incurred out of Scheduled period no action will be done 2 2 Criteria Setup Once condition is selected you need to set up event criteria following which any selected service will be executed Criteria consist of Schedule and Event which included Sensor input trigger Boot finish and Serial input data trigger 2 2 1 Schedule You can select the day from the week If you uncheck Sun and Sat Sun and Sat will be excluded from the condition If you enable Time only and disable Day of week and Date any action taken place during specific time of the day will be effective regardless day of week and Date of the year Schedule Sun Mon Tue Wed Thu Fri Sat P RW Time hh mm os loo e2 oo H Date mm dd o3 o1 os 80 Above setting tells you that any action e mail FTP or other services will be done if any Week event is happened from 9AM to 10PM from Monday to Friday from March to September of the year 2 2 2 Event Alarm seno
7. pool when he configure Router Ethernet adapter Local Area Connection Connection specific DNS Suffix Description ISA 3C509 3C509 in Legacy mode Physical Address 00 60 08 3C 40 90 DHCP Enabled Yes Autoconfiguration Enabled IP Address 192 168 0 158 Subnet Mask 255 255 255 0 Default Gateway DHCP Server 192 168 0 1 DNS Servers 168 126 63 1 168 126 63 2 2 2 LAN cable or Cross Over Cable Check out whether FlexWATCH server can be connected through LAN cable or Cross EE 92 Seyeon Tech Co Ltd Network Video Server User s Manual over cable 2 2 1 LAN Cable Environment If your PC is connected to network through LAN cable you need to connect FlexWATCH server to LAN port of Hub or Router 2 2 2 Cross over cable If LAN network is not available you can directly connect FlexWATCH server to your PC through Cross over cable In this case you need to prepare Cross over cable separately Note that The LAN cable included in the product package is not Cross over cable but normal straight cable and you need to set your PC IP address as 10 20 30 41 and connect the server with Factory default IP address 10 20 30 40 through web browser Following is brief procedure to connect the server after changing PC IP address 1 Click right button of your mouse on the My Network Places icon in the main screen window 2 Click right button
8. 1 Run Admin configuration panel 2 Click Alarm output control option in the Service configuration mode 3 Check the alarm output port and click Apply button Alarm Output DO Control Alarm Output DO Port Number 1 2 3 4 Enable Disable A el Ei Back Apply 4 3 Automatic Control of Alarm Output device Alarm Output device can automatically be controlled by setting up control condition properly This is to automatically to activate alarm output or any relay output device connected to the server Up to three different conditions per alarm output port with schedule Sensor or its Ue UOO 76 Seyeon Tech Co Ltd Network Video Server User s Manual combination is provided so as to set up powerful and various working condition for each alarm output device 1 Go to Advance service option in the Service configuration mode in the Admin window 2 Click None buffering service menu and select Alarm output menu 3 Check the service Enable option and select output port Alarm Output Service Configuration at Channel 1 Gar DOl Duration se Save Please click below link to configure the service condition gt Condition 1 Not Used a Condition 2 Not Used s Condition 3 Mot Used 4 Select Alarm Duration time from the drop down menu Note Alarm Duration time is to set up Alarm active time when alarm output device is activated by any condition 5 Go to Condition mode and set up condition to ac
9. Save Configuration menu Most of case system reboot comes last only after all the new configuration is done But some of system menu require system reboot in the middle of system configuration so that new setting can properly applied in the system Followings are list of option which require System reboot Network Configuration Date amp Time configuration with Time Zone change Serial Port configuration Memory assignment for Advance Service Factory Default r Note System reboot requires about 1Minutes of lead time Thus if you execute Reboot option please wait at least 1minutes to do other settings 3 Factory Default Factory Default is to reset all the configuration of the system as the initial status except Network Configuration This utility is recommended to use only when you lost all of your RE ee 98 Seyeon Tech Co Ltd Network Video Server User s Manual logics for system configuration since executing this option Except Network configuration will lose all of your setting 4 System Update System update can remotely be done through web page of the system or ftp option with telnet and Hyper Terminal mode In this user manual only web based system update method is described and ftp based system update method can separately provided 4 1 Description of files system FlexWATCH Server has 4 different files to get the system work In some case you may need to upgrade whole files or other cas
10. oe fen fs f fe gt Tmo force as fo fe e re fefe e we e _ ELMO ELDOME ERNITEC BDR 510 74 Seyeon Tech Co Ltd Network Video Server User s Manual 485 O O O DAIWA DMP 23 H1 LILIN PIH 717 485 O Tnn mesem maa ae fe fo e SA SRX 100B 485 Techwin NOTE Symbol Reference Preset function was program only Preset function was Lap Tested only Preset function was field Tested 2 5 Voice Kit Connection and configuration G 723 1 which is international standard for VOIP Voice Over IP communication based FW V10s voice kit can work with FlexWATCH server and you can enjoy not only live video stream but also full duplex two real time Voice through web browser or proprietary application program Voice broadcasting for voice connection by multiple users is also supported by the system as well Note Once Multi user connection is enabled only root Account user can enjoy full duplex audio and rest of users can listen only 1 Connect RS 232 Serial Cable with FW V10S to AUX or COM port of FlexWATCH server Serial cable is provided with FW V10S Refer to PIN out diagram above 2 Connect RS 232 Serial Cable to FW V10S 3 Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 4 Select Voice at COM or AUX mode and click Apply button Please note that Voice kit can be connected either AUX or COM port through RS 232 only
11. s Manual with Pre alarm buffer size Note that the sum of pre and post alarm can not exceed 10 frames Value Format Value strings can be sent together with e mails Please click d3hb mark in the admin page to get more information 3 2 e Mail condition set up Up to 3 different e mail conditions can be set up for each camera Schedule event or schedule amp event driven e mail condition can be set up to send e mail 1 Run the e mail condition set up window from the e mail service configuration for each channel 2 Check Enable field 3 Select mode for e mail trigger and set up condition 4 FTP Configuration Schedule event or schedule and event driven FTP functions supported by FlexWATCH server so that when there is any pre configured event is happened image will be sent and stored in the FTP server Buffered FTP and Periodic FTP function is supported by FlexWATCH Buffered FTP means that ftp will be done when any event is occurred Le change of status is generated and only pre post alarm buffered image can be sent to FTP server Periodic FTP means that image will continuously be sent to FTP server when there is any event No pre post alarm image will be sent to FTP server 4 1 Directory option FlexWATCH server provides powerful directory options so that user can easily create multiple ftp directory and send image into classified file directory as well Depends on the service type Buffering and No
12. 1999 2004 Seyeon Tech Co Ltd All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of Seyeon Tech Co Ltd Copyright 1999 2005 Seyeon Tech Co Ltd 810 12 Yeok Sam dong Kang Nam gu SEOUL 135 081 KOREA TEL 82 2 3017 0855 FAX 82 2 3017 0843 URL http www seyeon co kr http www flexwatch com DaO I I I lUO O 7 Seyeon Tech Co Ltd Network Video Server User s Manual Warning To prevent risk of electric shock Do not remove system case No user serviceable parts inside Any repair or modification for the product will be allowed to qualified service personal only Do not expose this appliance to water or moisture Do not install this product in Hazardous areas where highly combustible or explosive products are stored or used Important I nformation e Before installation please read and observe all instructions and warnings contained in this manual Retain this manual with the original receipt for future reference and warranty e f any items are missing from the package when you open the box please DO NOT install or OPERATRE FlexWATCH server Contact the local Dealer or Distributor e Please record following information for technical support and the track record in case of any theft or loss Serial Number can be found
13. 5676 ee ee ee a TOF id TH TERE BETS THREES AIK COM mo Si ae a Fi DES iji mm wO b 2D 2001 2190 90 dP Ha 485 422 Port RJ 45 Connector js divided into AUX and COM Mode AUX com R 232 Ports 12345 1 DCD 2 TS RS 232 Serial Cable A DTD Cross Cable OB9 Female 5 GND b OSR RTS o CIS g RI ne mm Steeg EE moe wee 1 1 2 Ports Connection for using two different devices AUX and COM part is provided for RS 232 and RS 485 or RS 422 connection This enables user to connect more external devices to the server and selectively use them per 63 Seyeon Tech Co Ltd Network Video Server User s Manual E his needs But same type of port for RS 232 RS 485 or RS 422 can not simultaneously be used For example if COM part of RS 232 is used by Hyper Terminal Connection COM part of RS 485 can not be operative In this case AUX part of RS 485 RS 422 or RS 232 port should be used Interface combination Ports Connection RS 232 RS 232 WA C 7 AUX RS232 COM R5232 RS 485 RS 485 RS 485 RS 422 HI 7 Ux TC AUX COM RS422 RS485 RS 422 RS 422 64 Seyeon Tech Co Ltd Network Video Server User s Manual AUZ or COM RS 232 RS 485 RS 232 Port Ally or COM RS485 RS485 AUX RS232 and COM RS485 or COM RS232 and AUX RS485 a wm Se D E AUX or COM RS 232 RS 422 RS 232 Fort AUX or COM RS422 Be AUX RS232 and COM RS422 or C
14. EE 72 Seyeon Tech Co Ltd Network Video Server User s Manual 5 System reboot will be recommended then click Reboot button 6 After rebooting Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 7 Click Voice Mode then following window will show up Voice Mode Configuration Current Port Als Current Protocol RS 2352 UOP Port 32001 o gt Network Ports Single Multi User GG Multi User Single User Ringing GG Enable Disable 12345678 4 4 CR WR CRW TH Fx TH Ru CR WR CR RR AUX COM AUX 32 COM 232 Back Apply UDP Port Voice kit use UDP port to transmit Voice kit If voice communication should be done through WAN network please make sure UDP port is not blocked to I nternet connection in router or firewall etc The default VDCP Voice Device Control Protocol port is 32001 please go to Network port configuration mode to change VDCP port if required ZE Application Idea By changing VDCP port you can install multiple Voice kit and FlexWATCH server behind the single broadband network Single Multi User Once Multiple users are selected only Admin account user can enjoy full duplex Audio and User account user can listen only Ringing This is to enable or disable sounds from the internal speaker of voice kit when there is a connection to Voice kit from outside SSS eee 73 Seyeon Tech Co Ltd Network Video Server User s Manual 8 Cli
15. bash prompt and then following messages will show up On the second line of the ethO message you can check the assigned IP and Mask values Gateway value is not seen here If the values are different from what you want to set up try again the Network configuration from step 8 30 Seyeon Tech Co Ltd Network Video Server User s Manual Bash ifconfig ethO Link encap Ethernet HWaddr 00 30 6F 81 00 AE inet addr 10 10 213 22 Bcast 10 10 255 255 Mask 255 255 0 0 UP BROADCAST RUNNING MULTICAST MTU 1500 Metric 1 RX packets 6382 errors 0 dropped 0 overruns 0 frame 0 TX packets 294 errors 0 dropped 0 overruns 0 carrier 0 collisions 2 txqueuelen 100 Interrupt 9 lo Link encap Local Loopback inet addr 127 0 0 1 Mask 255 0 0 0 UP LOOPBACK RUNNING MTU 16436 Metric 1 RX packets 0 errors 0 dropped 0 overruns 0 frame 0 TX packets 0 errors 0 dropped 0 overruns 0 carrier 0 collisions 0 txqueuelen 0 bash 12 Input savecfg command to save the changed configuration to Flash Memory And Input reboot command to reboot the system bash bash savecfg Saving a current config to flash memory OK Updated flash bash bash bash reboot Broadcast message from root ttyp0 Mon Sep 6 19 28 51 2004 The system is going down for reboot NOW bash E 31 Seyeon Tech Co Ltd Network Video Server User s Manual Live view amp Camera Configuration Once IP assignment is finished yo
16. e mail or send video amp data through PSTN line or other medium This is best alternative when the broadband Internet access is not available 4 1 External Modem connection Modem has to be connected to AUX Port with RS 232 Serial Cable Serial Ports Configuration COM Mode None sl AU Mode 1 Connect your MODEM and AUX Port at FlexWATCH server with RS 232 Serial cable 2 Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 3 Select Modem at AUX mode and click Apply button 4 System reboot will be recommended then click Reboot button 4 2 Application with Dial in out feature 4 2 1 Application with Dial in Dial in is to allow server connection from remote client This option is useful for the user to connect the server at any time Especially when the server sends e mail notification for the alarm and user want to check the situation 4 2 2 Application with Dial out eee 54 Seyeon Tech Co Ltd Network Video Server User s Manual Server can establish the Internet connection through PSTN line and send FTP or e mail when the alarm condition is triggered by any event Following can be done through Dial out function e Pre post alarm image sending through e mail e Pre post alarm image sending to FTP server through FTP function e Establish connection with AOIP server when the event is happened server can send e mail notification for the alarm and can kee
17. ex Flexwatch and press OK button 27 Seyeon Tech Co Ltd Network Video Server User s Manual EE Connection Description 2 x a New Connection Enter a name and choose an icon for the connection Name FlexwWAT CH Icon 4 Select the connected COM port with serial cable and press OK button BH FlexWATCH Enter details for the phone number that you want to dial Country regian Korea Republic off 22 Area code be Phone number DEEN Connect using Cancel 5 When Port Settings window show up input each values from the table below 2x Port Settings Bits per second Ieam sl Data bits fs sf Parity Noe sl Stop bits iti wt Flow control Noe sl Restore Defaults Serial Port Settings Value Bits per Second 115200 Data bits 8 Parity None 28 Seyeon Tech Co Ltd Network Video Server User s Manual Stop bits 1 Flow control None 6 After setting Hyper Terminal press Enter key several times and then you can see messages as below Input Login ID and Password Factory defaults for Admin ID and Password are root root Seyeon Tech Co Ltd 2001 2003 Linux Kernel 2 4 20 syl1 FlexWATCH login 7 If you correctly input Login ID and Password bash prompt will show up as below FlexWATCH login root Password SYSTEM FlexWATCH VERSION 3 0 040130 MODEL FW 3110 login 504 root login on ttySO bash
18. 35 Seyeon Tech Co Ltd Network Video Server User s Manual video related value string for his own application Camera Configuration Default Video Format NTSC PAL Video with UART sensor data Enable Video with channel name Enable Video with server name Enable Video with IP address Enable Image Encryption Enable Encryption Key ess Back Apply Default Video Format To manually change video format Note that server auto sense the video format Video with UART sensor data Serial input data can be sent along with video so that application program can read serial input data Video with channel name To send video along with channel name Video with server name To send video along with server name Video with IP address To send video along with IP Address Image encryption Image encryption is security feature Once it is enabled user must enter encryption code to view live video amp Note All of video related values are encrypted in the JPEG image and can not be read by any program as it is It is intended to help application program developer to utilize video related value string for his own specific application Manufacturer can provide more technical documentation for the programmer to decrypt value string for his programming ee 36 Seyeon Tech Co Ltd Network Video Server User s Manual Thus please contact your local vendor to get more in depth technical info to decrypt the value strin
19. Please Select Network Status menu in the Network configuration mode of Admin Window Network Status Common Status Gateway 211 255 36 254 Gateway Device DWS1 1668 DNS2 IP Address Netmask 255 255 255 126 MAC Address PPPoE Status Connection Status IP Address oS O Netmask WAN Modem Status Connection Type PPP Server Dial Inj Connection Status Lei ip Remote Ip Netmask S y O Back Reload LAM Status E 61 Seyeon Tech Co Ltd Network Video Server User s Manual External Device connection amp configuration External device such as Serial input device Serial output UART device PTZ pan Tilt Zoom device Audio kit and Alarm input and output device can be connected to the system and controlled over the TCP IP network L Serial Ports Configuration Guide This chapter will guide you how to install and configure Serial interface devices FlexWATCH server is designed to support simultaneously TWO different Serial interface devices RS 232 RS 485 RS 422 through COM and AUX ports 1 1 Hardware Description There are two DB 9 terminal ports Aux and COM for RS 232 interfaces and one RJ 45 terminal port for RS 485 and RS 422 interfaces at the rear part of FlexWATCH server as below picture RJ 45 terminal port provides 8 pins that are divided into AUX and COM part as well 1 1 1 Pin Out Information E 62 Seyeon Tech Co Ltd Network Video Server User s Manual 123
20. RH 100 100 100 is hypersensitive Motion Enable Enable Disable Time Stamp Enable Disable Back Default User defined camera name will be appeared on the camera name column of video Up to 20 different English characters can be used Notice If you are using 2 Byte Unicode Character number of character is limited to 10 Image Size 4 different size of video can be set up Pull IL Large Normal Smal NTSC 704 x 480 704 x 240 352 x 240 176 x 112 704 x 576 704 x 288 352 x 288 176 x 144 ZE Application Idea Full size of video can show interlaced video when the camera is displaying fast moving picture To avoid interlaced video use large size of video which use Field image only Note that in this case camera quality can slightly be degraded Channel install Whether to enable video channel or not If Disable is selected camera will not be SSS eee 38 Seyeon Tech Co Ltd Network Video Server User s Manual displayed Video Source color and Gray mode option Image Quality 5 quality levels highest high normal low lowest L Note Please note that if you increase image size and quality actual J PEG file size will be increased and this may affect actual transmission frame rate Thus you are required to check out your network bandwidth available for FlexWATCH server and select the right size and quality of video Motion Detection Refer to description about Motio
21. a DHCP server which can be a computer on the network or another piece of hardware such as router A dynamic IP address may change every time your computer connects to the network DHCP Dynamic Host Configuration Protocol DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP IP network DCHP eliminates troublesome job to manually assign permanent IP addresses to every device on your network DHCP software typically runs in servers and is also found in network devices such as routers Most of Cable Modem for Internet access uses DHCP Public IP address and Private IP address Public IP address is an IP address which can be identified uniquely in Internet world All IP addresses excluding private IP addresses are public IP addresses Private IP addresses range from 10 0 0 0 until 10 255 255 255 and from 192 168 0 0 to 192 168 255 255 Generally speaking private IP addresses are used in local area network which are hidden from the Internet world Also when public IP addresses not enough private IP addresses are used while sharing global IP addresses Router Router is a network hardware which routes either Private or Public IP address to Public network so that network device between private IP network and Public IP network can communicate over the network Router has NAT Network Address Translation function and through this function Public IP address will be mapped into private IP network so that Netwo
22. be acquired by contact your local distributor or sales flexwatch com 6 2 AOIP configuration As described above once you register product in the AOIP server and Network setting is correctly done to user AOIP function you need to configure AOIP function in the FlexWATCH server 1 Check the Enable option to use AOIP function 2 Type in AOIP server address Either Domain name or IP address can be typed in 3 Select whether to use HTTP or NVCP TX port HTTP port must be selected to view ADIP Service Enable Disable ADIP Server IP www aoip co kr HTTP Port Enable Disable MVCP Tx Port Enable Disable AOIP Server IP AOIP server IP is subject to change depending on where you are and who is your local distributor since AOIP server can be run by local distributor in some countries If there is no local AOIP service available you can contact manufacturer to use www aoip co kr Is AOIP Service address run by manufacturer HTTP Port This is enable HTTP connects to AOIP server You must select Enable option NVCP TX Port eene 60 Seyeon Tech Co Ltd Network Video Server User s Manual NVCP Tx Port should be enabled only when video is transmitter to NDVR server such as FW 5440 and FW 5000 or Video proxy server supplied by FlexWATCH server If not do not enable this option 7 Network Status You can see all the network status configured in the system through Network status option
23. browser PTZ PTZ pan tilt zoom device can be controlled through web browser When click PTZ button PTZ control panel will separately be appeared But note that you need to get permission to control it SSS ee 34 Seyeon Tech Co Ltd Network Video Server User s Manual Output control Relay output device can be controlled through simple view page But note that you need to get permission to control it 2 FW Voyager based view and recording FW Voyager is web based DVR software for personal video recording Using this free software user can easily install the software and do video recording at any time Note that FW Voyager is works on MS Internet explorer of Window OS Click Voyager tab in the web page of the server Wait till the Voyager program is automatically downloaded Click yes in the Security warning panel Then software will automatically installed For the operation of the software please refer to user guide of FW Voyager software included in the product CD MOli isl your remote eye e surveillance le OOD GM Of OAS beet 2 amp PENT 5 91 KB frame 30 fps 3 Camera configuration This is to configure camera related settings such as camera value string and video quality setting 3 1 Camera value string configuration Some of video related value string can be transmitted along with live video stream so that client program can receive and utilize eee a
24. channel and 120fps NTSC 100fps PAL for 4 cameras at 5kbps image size Channel based user authentication Channel based multi user level protection for camera control PTZ control Alarm output and Audio control 2400 frames Pre Post video alarm buffer 2400 frames pre post alarm buffer to store event triggered video in the internal memory Built in Motion detection and time stamp Built in motion detection per each camera with up to 144 block of motion area to filter out unnecessary motion detection area Optional time stamp on the video DE 10 Seyeon Tech Co Ltd Network Video Server User s Manual 2 2 Product Specification Hardware 32bit Embedded CPU Flash 4Mbytes SDRAM 32Mbytes Hardware Motion J PEG engine Linux version 2 4 xx operating system System Requirements OS Windows 95 98 2000 XP NT ME Linux Mac Unix Linux Operation system Browser MS Internet explorer 5 x or above Netscape 6 x or above PC H W Pentium III 500M or above RAM 64 MB and above Network Protocols HTTP TCP IP FTP Telnet RARP PPP PAP CHAP DHCP SMTP client e mail NTP Java Video NTSC 704x480 704x240 352x240 176x112 BAL 704x576 704x288 352x288 176x144 NTSC PAL video auto sensing Frame Rate 30fps 352X240 352x288 based on Pentium4 2 0G and 100M dedicated network Image quality 6 levels Auxiliary Video in amp output 1 video inputs amp 1 loop through outputs LA
25. entry to AAF table ing Trying ping 10 10 225 100 Description of Window Menu Description A Serial No MAC Address Enter FlexWATCH server Serial No Mac of System address attached at the bottom of the unit and select the LAN port WAN PORT is only for setting up FW 5000 and FW 5440 model which has two LAN Card inside of the box B IP Address on PC Auto scanned IP address of user s computer with IPI nstallationWizard exe running on 25 Seyeon Tech Co Ltd Network Video Server User s Manual IP Address Input an IP address to be assigned to FlexWATCH server Note that the IP must be directly connectable with user s PC The above IP 10 10 225 100 is only an example C IP Subnet Gateway Whether to change IP Subnet and Gate or IP and Subnet mask only D Set I P Address Button To activate a new IP assignment click this button E Save IP Address Button To save IP Address in the Flash Memory F Go to Home Page Button To launch FlexWATCH Web browser and start other configuration through Administration page G Telnet to System Button To guide you Telnet mode for Advanced Configuration H Result window Show the result of IP assignment If failed try again from the start or use other configuration method 3 Input the Serial No MAC address and Select LAN Port 4 Input the IP address which will be assigned to the system 5 Click Set IP Address button to save the above
26. is enabled in the FlexWATCH server System Information gt gt Date amp Time Condition 1 gt Admin Password Service Recording x Access Permission Module ID o User Registration Serial Ports SE Rx Module Registration Enable Disable C Always Network Configuration Schedule Only gt gt LANCIP address Select Mode gt gt WAN Ethernet P Event Only gt gt Port Mapping Schedule and Event gt Network Ports Schedule gt WAN Modem Sun Mon Tue Wed Thu Fri Sat gt View Network Status Week Network Status Notify a a ee EN gt AOIP Setup E Time hh mm xx xx xx xx gt NTP Setup E Date mmfdd xx xx xx xx Service Configuration Event Service Dial Up Path 12 3 456 e Ge e Input Open State DD DD E E gt gt sn Alarm Output Control Input Clase State eee DW H Advanced Service Motion Detection KM UD O E E IC SE Camera Connected DO CODOD E onfiguration Recording Configuration Camera Disconnected COOCOO E E Local Device 0 Channel 1 _Back_ _Save_ Channel 2 Channel 3 H Channel 4 View Recording Condition Recording Mode EN C a D Le CE a KE FE OOO 40 Seyeon Tech Co Ltd Network Video Server User s Manual Recording in the FW Manager To record motion triggered image in the FW Manager NDVR Software client program you should not use Software motio
27. module at NDVR server side should also be enabled as well Two different modes are provided as a connection type One is Passive and the other is Active mode Depending on which device tries to establish the connection to the other party the connection type will be decided Passive mode NDVR server tries to establish connection to FlexWATCH server Active Mode FlexWATCH server tries to establish connection to NDVR server Once connection type is decided in the FlexWATCH server the connection type in the NDVR server should be opposite so that it can communicate with FlexWATCH server For example once Passive mode is set up in the FlexWATCH server Active mode must be set in the NDVR server SSS eee 47 Seyeon Tech Co Ltd Network Video Server User s Manual EE 1 Click TX Module registration menu in the System configuration mode of Admin window 2 Type in NVCP Password in the NVCP Password configuration filed L Notice NVCP Password is security feature which authenticate server access by RX module FW 5440 or 5000 NDVR server to FlexWATCH server Once NVCP Password is configured that password must be set up in the NDVR server to get video from FlexWATCH server Thus you must make a note of NVCP password N CP Password Configuration New Password Confirm Password Back Save l Itis security code to authenticate communcation between the video server and NVR server The default
28. must be used for FlexWATCH server to assign an IP address from your PC keeping Subnet mask amp default gateway as same that of your PC For example 192 168 0 155 or other available IP address except 192 168 0 158 can be assigned to FlexWATCH server since it is the same class of your IP address and can be communicated in your local network If you want to check out whether 192 168 0 155 is available Please try ping command in the DOS window If there is any response it means 192 168 0 155 is assigned to other network device Thus you need to randomly select other IP address and try ping test or consult with your network administrator C gt ping 192 168 0 155 Pinging 192 168 0 155 with 32 bytes of data Seyeon Tech Co Ltd Network Video Server User s Manual Reply from 192 168 0 155 bytes 32 time 10ms TTL 128 Reply from 192 168 0 155 bytes 32 time lt 10ms TTL 128 Reply from 192 168 0 155 bytes 32 time lt 10ms TTL 128 Reply from 192 168 0 155 bytes 32 time lt 10ms TTL 128 2 1 2 DHCP Enabled PC If your PC is set to use DHCP you need to check out IP address of your PC using ipconfig command at DOS Prompt window You need to get IP address from your network administrator to assign it to FlexWATCH server IP address should be Surplus of IP address which will be not randomly assigned to any network device in your network Your network administrator must make sure that IP address should be excluded from IP
29. of your mouse on the Local area connection icon and select Property option 3 Select Internet protocol TCP IP option and click Property icon 4 Select use the following IP address option from the TCP IP property option and set the IP address as follow IP address 10 20 30 41 Network Mask 255 255 255 0 5 Connect FlexWATCH server using Cross over cable to your PC and run your web browser and enter default IP address 10 20 30 40 of FlexWATCH server in the URL field Note that Cross over cable is not supplied with product 6 Once you are connected to the server click Admin icon and click LAN configuration menu 7 Enter IP address you would like to assign to the FlexWATCH server and change your PC IP address again SSS eee 23 Seyeon Tech Co Ltd Network Video Server User s Manual 2 3 PC Environment Check out whether your PC is connected to LAN or WAN network or stand alone If stand alone you need to use Cross over cable or build up LAN environment to use LAN cable 3 Factory Default Please refer to the following factory defaults to change setting up Factory Default Admin ID root Admin password root IP address 10 20 30 40 Network mask 255 255 255 0 4 IP Assignment FlexWATCH server can be configured by two different configuration method and following is brief explanation Installation Wizard Program IP installation program is provided in CD form Once Fl
30. only since respective service e mail ftp or Alarm buffering service consumes separate memory in addition to pre alarm buffer size configured to make a real service Delay between pre alarm image This is the set up pre alarm speed when the server store image in the system memory 1000mse is equal to 1sec and basic unit is 10msec If you want to get 10fps pre alarm speed 10 will be very appropriate number for Delay value Maximum Pre alarm buffer should be the half size of Total Pre Alarm buffer size memory assigned in the system since Pre alarm images for e mail FTP or alarm buffering service are taken from Pre alarm buffer pool and any Pre alarm image for these services require additional memory space 1 Go to Advance service mode in the Service configuration section 2 Go to Buffering service mode 3 Set up pre alarm Buffer size and delay time 4 Click Buffer Calculator button to run the calculator 1 2 Buffer calculator Through Buffer Calculator option you can easily calculate assignable pre post alarm buffer size for each channel before setting up Pre Post alarm buffer frame in the system memory Following is logic for Pre Post alarm assignment By running buffer calculator you can try pre post alarm size Total Pre alarm buffer size 40 SSS SS 81 Seyeon Tech Co Ltd Network Video Server User s Manual Alarm buffering service size 60 e Total Buffer size is variable de
31. pre post alarm image per video channel can be sent to ftp server when the event is occurred Alarm buffering service Pre configured number of Pre post alarm image will be stored in the system memory and user can playback stored image through web browser Steps to use Buffering Service Following is a step to configure and use Buffering services A System memory allocation This is to allocated limited system memory for e mail SSS eee 78 Seyeon Tech Co Ltd Network Video Server User s Manual amp ftp and Alarm buffering service B Pre alarm buffer size Once memory allocation is done assign Pre alarm buffer size Pre alarm image buffer pool to be used for e mail FTP and Alarm buffering services Any pre alarm buffer for respective e mail fto and Alarm buffering services can be done within Pre alarm buffer size C Pre Post alarm for respective service Once Pre Alarm Buffer Size is decided go to respective e mail ftp and alarm buffering service menu and configure the options 1 1 System and Pre Alarm Buffer memory 1 1 1 System Memory allocation The number of Pre Post alarm image for advanced services should be pre defined to effectively use the limited memory capacity an Buffering Service This configuration is for advanced services which need Pre Post alarm video e mail tp and alarm buffering services recording in the system memory Assign memory space for each services Total buffer size 17300 kh ri
32. service condition 8 Click Advance Service menu in the Admin window and click Stop and Apply button to start record alarm triggered image in the system memory L Note that Stop amp Apply button in the Advance Service window must be refreshed by clicking the button to start recording of any video in the memory Otherwise no pre post alarm image can be stored 5 2 Playback of Pre post alarm I mage Once Alarm buffering service configuration is correctly done and pre post alarm image is stored any stored Pre post alarm image can remotely playback through admin window 1 Click Alarm Buffering Service menu from the Advance Service configuration menu 95 Seyeon Tech Co Ltd Network Video Server User s Manual EE Alarm Buffering Service Configuration at Camera 1 Pre alarm Buffer Size 200 frames aa Check video buffer Delay between pre alarm images 0 msec aa Check video buffer Number of pre alarm images 50 frames Number of post alarm images 100 frames Delay between post alarm images iw unit unit 10 msec Back Save Notice Pre post alarm images will be stored in the pre defined buffer space according to the service conditions Once configuration is done please go to Advanced Services page after setting up alarm condition below and click Apply button to start Alarm Buffering serivce Otherwise no recording with new configuration will be started Preview single images Preview m
33. type of sensor Please check out sensor type connected to FlexWATCH server ee 86 Seyeon Tech Co Ltd Network Video Server User s Manual 3 e mail configuration Schedule event or schedule and event driven e mail sending is supported by the server so that when there is any pre configured event is happened e mail notice will be sent to any e mail account 3 1 e mail function configuration Up to 10 pre post alarm image can be appended and sent through one e mail when the event happens By configuring pre post alarm for e mail you can decide the number of image to be sent by an e mail 1 Go to Advance service mode in the Service configuration section 2 Go to Buffering service mode and set up pre post alarm image for e mail 3 Select e mail option from menu 4 Set up e mail account in the e mail configuration This setting will be applied for all Cameras E mail Service Configuration Service Enable Disable SMTP server address Authentication Lagin Enable Disable User ID Pd Password Sender Email SERVER S N 00206f003267 lt E mailaddresst 1 E mail address2 0 E mail address3 s Back Save SMTP Service address This is sending mail server address of ISP from which you get Internet access service To get this info consult with your Internet service provider or check the e mail setting in your e mail program such as outlook or Eudora SSS eee 87 Seyeon Tech Co
34. underside of FlexWATCH server Product Model Purchase Date Serial Number E 8 Seyeon Tech Co Ltd Network Video Server User s Manual Overview of FlexWATCH Server 1l Packing List Please check and make sure following items are included in your package without any missing items If there are any missing items please refer to your local distributor A FlEXWATCH ai B RS 232 Serial Geier P Cross cable DB9 Female C Power AGG DEC E Power Cable SMPS DC 12V Adapter D User s Manual CD LUNI E O O 9 Seyeon Tech Co Ltd Network Video Server User s Manual 2 What is Flex WATCH The FlexWATCH server is the Network Video Server which transmits digital images captured by Analog CCD camera over the Internet So users can view real time live images over the Internet at anytime and anywhere using the standard web browser such as MS Internet Explorer or Netscape Communicator There is no need other specific software to view real time live images over the Internet The FlexWATCH server is state of the art device and leads new generation of monitoring and security solution 2 1 Key Function of FlexWATCH Self contained stable system Built in Web server Real time operation system and hardware video compression engines are included No PC required to transmits real time video over the TCP IP network High performance of video transmission 30fps NTSC 25FPS PAL per each
35. 01 10000 65535 Back Anply 3 1 HTTP port configuration When you need to change Default HTTP Port 80 to other port you can change HTTP port This is very useful when more than one server should be installed behind a router By assigning different HTTP port number for each server and configure port forwarding feature of Router you can install more than one server behind the router For more information about this please contact your local vendor 3 2 NVCP Tx Port Tx port is a TCP port number through which FlexWATCH server can communicate with other devices such as FW 5440 or FW 5000 NDVR servers This port number is user definable NVCP Tx port must be opened when the FlexWATCH server transmits data through Internet in a Passive way When TX Module Registration is configured as PASSIVE MODE When NVCP port is to be used you must open TCP port in the router as well 3 3 VDCP Port configuration VDCP port is UDP port for Voice Communication By changing VDCP port Default number is 32001 you can install more than one Voice kit and Video server under the router DEE El 53 Seyeon Tech Co Ltd Network Video Server User s Manual Note that when Voice Kit is connected to I nternet respective UDP port of the router must be opened 4 WAN Configuration and Application Server is designed to make a call to ISP or can receive a call from outside so that server can establish Internet connect to send FTP
36. 35mm H Weight 0 5kg without power supply PWR Supply DC 12 Volt 1 5Am SMPS Operating temp 40 125 F 5 50 C Approval FCC Class A CE Class A Accessories Console cable for system set up LAN cable CD for User Guide Installation wizard amp Technical note Quick Installation guide Miscellaneous Voice kit FW V10s support Freely downloadable NDVR Software AVI conversion tool support by FW voyager Work with FW Manager NDVR S W 11 Seyeon Tech Co Ltd Network Video Server User s Manual Dynamic IP support through AOIP 2 3 Basic Network Connection Diagram FlexWATCH server provides flexible connectivity with any type of networks available around you such as Leased line Cable modem xDSL line and PSTN POT line Thus it can be installed either in LAN or WAN environment as long as there is network available But its configuration is subject to change depending on its environment Following is basic network diagram for using FlexWATCH server Thus you are required to consult with your network administrator or network consultant for more information Also you are recommended to refer to Network configuration guide in the CD manual for more details 2 3 1 Leased Line connection Simply get a Static IP address from Network Administrator and assign IP address to FlexWATCH server and view from the Internet Global Static FP fom Leased Line PTZ camera Loop Thinaug
37. 5 04 3 Serial Number 00 30 6F 63 00 01 3 Browse your pc and select the right file to update following the update guide If you want to skip specific update click Skip button E nO 101 Seyeon Tech Co Ltd Network Video Server User s Manual EE Upload Firmware Image Please upload e_kerow file for Firmware If you don t want to upload Firmware Please click Skip you will get the next step For the system safety Do not close this window compulsory Select file Browse Next Skip 4 Once update is successfully done following result will come up Write Kernel Image to Flash Please wait for awe Ir will take a few seconds 4 After procedure is completed you will see the next page Please click Cancel this system will reboot For the system safety Do not close this window compulsory File Name _ker_xx File Size 625 EB Previous Mest Cancel 5 If you want to update RAM Disk System and web page please click Next button follow the web guide to update more files 6 If all of file update is finished System Reboot window will come and do system reboot to apply new update Upgrade Done This command will reset this system All connections will be disconnected and Flex WATCH can not monitor your site within several seconds You should to reboot this system After reboot restart your browsers Reboot IS 102 Seyeon Tech Co Ltd Net
38. Ltd Network Video Server User s Manual Authentication Login Now these days most of ISP is try to authenticate sender e mail address due to security and spam mail issue If sender authentication is enabled by your ISP you need to get your login ID and Password from your e mail service provider Sender E MAIL put the sender e mail If you use system default sender e mail address it will not work E mail address 1 3 put recipient e mail address Up to 3 different e mail account can be supported 5 Select channel to configure e mail for each camera after setting up e mail account E mail service configuration for Camera Maximum 10 pre post alarm frame can be transmitted through e mail trigger Assigned Pre alarm Buffer Size 0 frames Delay between pre alarm images U mseci Number of pre alarm images lo frames Number of post alarm images lo frames Delay between post alarm images lc unit funit 10 msec Subject Message From FlexWATCH 0 0 Message Value Format NONE INT HEX BIN IPA EWT O EE eg e Ieielele OOJOO sack Save Ww ha Re Number of Pre alarm images Number of pre alarm image should be less than Assigned Pre alarm buffer size and maximum number of pre alarm can not exceed 10 frames Number of post alarm images Less than 10 frames can be assigned as post alarm images Post alarm has nothing to do El 88 Seyeon Tech Co Ltd Network Video Server User
39. N Interface 10 100BaseT Ethernet auto negotiation Alarm I O interface 1 Opto coupled inputs or ldigital inputs 1 Relay output Serial Interface Two serial ports for console modem PSTN amp GSM serial input output device PTZ or voice kit Each port can be configured as RS 232 RS 485 or RS 422 max 115kbit s Security features Channel based multi user level protection for camera access PTZ Alarm I O Voice IP address Filtering Image Encryption Advanced Service Up to 5M Pre Post alarm buffer memory Built in Motion detections Up to 144 blocks e mail FTP alarm Buffer by event or schedule IP notification Alarm Notification to e mail CGI path by event or schedule PTZ amp UART Control PTZ and UART device control through serial interface Up to 29 PTZ protocols from Panasonic Dome Pelco P amp D protocol Sony EVI D30 Kalateland AD Delta dome Vicon Surveyor CannonVC C4 and etc Refer to user guide for more vendors X10 device control Others Video loss detection Up to 100 concurrent user access Dial in out via PSTN or GSM modem Time stamp on Video Transmit Serial input data transfer with Video P notification by e mail Developer support Provides HTTP CGI API ActiveX control development kit Management Configurable by serial web or telnet Remote system update via telnet FTP or web browser Dimension Size 122mMm W x 84mm D x
40. Network Video Server User s Manual EE User s Guide Flex WATCH 3110 Version 3 0 Rev0O Seyeon Technology Co Ltd www flexwatch com Seyeon Tech Co Ltd Network Video Server User s Manual Table of Contents Overview of FlexWATCH Server cccccsecscccuceceeecueueveeeceeueuauauenaeeeuauauanenenas 9 1 Se ele EC 9 2 What is FleXWATCH oo cccsecccseccceeececseccereseesueeccseseneseerresetteetirteeteeneenes 10 2 1 Key Function of FlexWATCH 00 cccccccccecececccecececeeeceeeeeeceeerereenteenteaeens 10 2 2 Product SPECICATION EEN 11 2 3 Basic Network Connection Dice ecient rere re er tn te E E ree 12 2 4 POD lg Lg OD EE 14 3 Hardware DCS COM renaren EEE N E EER 16 3 1 Caution and observance ccccceccucceeceeeceeceeecececeeceeecereeeaeeteereeereneaenes 16 3 2 Hardware DE SCID UO ME 16 IP IHte ET 18 1 Key Words for Network 18 2 Check Points before IP O LE 20 2 EE 20 2 2 LAN cable or Cross Over Cable 22 2 3 PC Environment eee eRe RETR ee eee ee ee en reer ee 24 3 PaClory Dela se saetec incense eutareduacrssteseuceniniepiiecstucerqurenpestssrecrivasanessenaieianen 24 4 ip EEGENEN 24 4 1 Through Installation Wizard Program cccccccceeeeeeeeeeeeeeeeeeeeneeeeeeeeanas 24 d Zum Assignment through Hyper Terminal mode 27 Live view amp Camera Confguratton e 32 L Live View 32 SSS eee 2 Seyeon Tech Co Ltd Network Video Server User s Manual 1 1 Activex based simple view E
41. O EE EEN 87 3 2 e Mail condition set Die ME 89 4 FTP CONFIQUIATION cece cece cece eee e ence cent teen eee ee tense eeeeeeeeeeeeeeeteseengeseeeeeeeeanenags 89 4 1 DW CEO RY eine E 89 4 2 FTP service CO TIC E EE 92 5 Alarm BUTFEriING Service 94 5 1 Alarm Buffering Service Configuration sssesererrererrrrererrererrerererrrrere 94 5 2 Playback of Pre post alarm Image c cece cece cece cesses eeeeeeeeeeeeeneeeeeneenees 95 Sensor Notification service ccccccccccecsscecccccceeessacceccccceessutececcecerttsuteseceeeetreey 96 IN dE 98 1 save CORNO SUO ceina E E E A rE REER 98 DEE 5 Seyeon Tech Co Ltd Network Video Server User s Manual QD Beboot vececccccccecseccceccccecseecccccscevsseussecescecsessuesessececsusuesesececevtvatesececeetneres 98 3 Pac On Dora EEN 98 4 System Update 99 4 1 Description of files system EE 99 4 2 Upar Deel e EE 101 E 6 Seyeon Tech Co Ltd Network Video Server User s Manual Notice e The material in this document is for information only and is subject to change without notice While reasonable efforts have been made in the preparation of this document to assure its accuracy Seyeon Tech assumes no liability resulting from errors or omissions in this document or from the use of the information contained herein e Seyeon Tech reserves the right to make changes in the product design without reservation and without notification to its users Copyright Copyright
42. OM RS232 and AUX RS422 You cannot make use of AUX RS232 port and AUX RS485 422 part at the same time Also it is not available to use of COM RS232 port and COM RS485 422 part together 2 Installation amp Configuration of External Device 2 1 Console Hyper Terminal cable connection Console has to be connected to COM Port with RS 232 Serial cable Serial Ports Configuration COM Mode Console AJ Mode Serial Input Serial Output Mone 1 Connect COM1 or COM 2 Port at your PC and COM Port at FlexWATCH server with RS 232 Serial cable 2 Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration SSS eee 65 Seyeon Tech Co Ltd Network Video Server User s Manual 3 Select Console at COM mode and Click Apply button 4 System reboot will be recommended then click Reboot button 2 2 Serial Input device Serial input device such as Car Speed sensor BOG sensor POS Point of sales ATM device which communicate with external device through RS 232 port can be integrated with the system And that data can be transmitted along with video to anywhere over the TCP IP network 1 Connect your Serial Input Device to RS422 485 Port or RS232 COM or AUX port 2 Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 3 Select Serial Input at COM or AUX mode and Click Apply button 4 System reboot will be recommended
43. R 1 2 Java Applet based liVe VICW ccc cece cece rO 33 1 3 Live view POC e re TEEN ER 2 FW Voyager based view ANC recording sessssererrrrererrererrrrererrrrerrrrrrerrrrerre 35 3 Camera Scint tel leide E 35 3 1 Camera value String CONTIOUIALION EE 35 3 2 Camera COO O EE 37 3 3 Video Motion Detection cc ccccccccececececeeeeeeeeceecereeeaeesecereceeeeeaeereneaenes 39 System CONTIGUIATION WE 42 1 ERR lei teig nee ME 42 A Date amp Time 42 2 1 Date amp Time in the server cJock 42 2 2 Date amp Time USING NTP server 43 3 Admin Password DOCU ET 43 4 access Control and User FEC SU ALON PET E E E E E 43 d Full Access 44 4 2 Limited Access and User Kegel el ER 44 D Frame rate Control 46 6 Tx Module REJIS UCONN UNV CP EE 47 Network Configuration siiniscccnsnnssiescunnsdecssiurinesseasenenenunsscrenmnnternesnesneveunenns 50 1 Network COonfiguration 50 UE Sc dot E 50 1 2 DACP e TE 50 3 Seyeon Tech Co Ltd Network Video Server User s Manual 2 PPPoE CONT QULATION NEEN 52 3 Network OPC COMtOUT AION NEE 53 3 1 HTTP port Confguration ccc cece eee cece teen cece eee eeeeeeeeeeeeeeeeeeeeeegeeeeeenegs 53 B 2 NVOP TX POrt esicesessiiuesetiii tetikte teana EEEL EEEE EEEE EEE EE EE EEEEE EEEE EEEE EEEE 53 3 3 VDCP Port Sitte Te en SE 4 WAN Configuration ANd Appitcatton seen cece ee eeeeeeeeeeeeeeeeteeeeaeeneenees 54 4 1 External Modem conpnecton 54 4 2 Application with Dial in Out feature cc cccccccccc
44. c FTP means that image will continuously be sent to FTP server when there is any event No pre post alarm image will be sent to FTP server 1 Go to Advance Service menu in the service configuration mode and select None Buffering Service option 2 Set up FTP directory and file name option 3 Select the camera and set up FTP condition for each camera Example 1 Let s suppose that a Camera takes a image every 15min and sends it to FTP server continuously And the images are being accumulatively stored under the directory namely FlexWATCH in the FTP server for one year Before starting this configuration you must create a cetain directory name in the FTP server The directory name FlexWATCH ts only an example 1 Go to Advanced Services gt Non buffering Service gt FTP Periodic gt Cameral gt Conditionl on the Admin menu Select Enable and Always then click Save 2 Goto Camera 1 menu Input 90000 units at Delay between I mages and click Save 3 Go to FTP Periodic menu Please set up as below then click Save DEE 93 Seyeon Tech Co Ltd Network Video Server User s Manual 4 Go to Advanced Services menu Status Stop pack stat sep D Click Apply button to apply the new service configuration as above Close the window of Admin menu When Save configuration window pop up click Save Configuration
45. ce Sensor Notification Service Configuration Service Enable Disable IP Address 192 168 0 nxx CGI Path User ID Password som Ee Please click the below link to configure Sensor Notification service for each video channel Input 1 e Input 2 gt Input 3 se Input 4 IP Address IP address of target device to which sensor notification will be sent CGI Path Common Gateway Interface to the Application program User ID Password Authentication ID and Password of the application program 3 Type in CGI Path and User ID amp Password to third party application program 4 Select sensor input number 5 Type CGI Name User definable and set up condition to trigger Sensor notification function E 97 Seyeon Tech Co Ltd Network Video Server User s Manual Utilities Utilities is to manage and control system properly Save Configuration Flash Update System Reboot and system upgrade options are provided 1 Save Configuration This is to save all new configuration and settings in the system memory Once new configuration is saved by Save Configuration menu new configuration will permanently saved in the system memory only after system Reboot or system power off 2 Reboot Reboot means restart system It is needed to reinitialize and restart system after changing some configurations that has influence on the system Thus it is highly recommended to reboot the system after executing
46. ce Voice kit PTZ Console for Hyper Terminal must be connected to this port only D LAN LED Blinking only when LAN is connected to the network Green light on when LAN connection is OK E PWR LED Indicate power on off Always red light on when turned on Rear Panel View A BNC IN OUT 4V ideo input and 4 loop through video output B General I O 1 Opto coupled input and 1 output C RS 232 RS 232 Port to connect Serial input device Voice kit PTZ device or Modem F RS 485 To connect RS 485 based PTZ device For more information refer to External device configuration menu 17 Seyeon Tech Co Ltd Network Video Server User s Manual IP assignment 1 Key Words for Network LAN Local Area Network Under the LAN network any network device in the same LAN network can be accessed by any other network device But LAN network can not be accessed from the Internet WAN Most of case LAN is built after Router which is connected to WAN network so that Network device in the local area network can access to the Internet through Router Most of case LAN networked device can not be accessed from the Internet WAN unless it is not configured to be accessed from the Internet through NAT function of router WAN Wide Area Network WAN enables all network device can be accessed by each other over the Internet It included Leased Line Cable modem xDSL ISDN and Telephone line etc IP address P address is abbreviation of Interne
47. ck Save button to save your configuration 3 Alarm input device connection FlexWATCH server has Alarm Sensor interface so that it can send alarm notification by activating e mail or FTP function or activate alarm output device such as Siren or light FlexWATCH server supports opto coupled input circuit and any dry contact type of Alarm sensor can easily be interfaced to the server Following is circuit diagram for Alarm input part Opto coupled Sensor input Diagram FlexWATCH 7 Sensor 1 Simply connect the alarm sensor to the server 2 Go to Alarm input out menu to name the alarm input name 3 Once configuration is done alarm based services can be done such as e mail FTP Sensor notification ZE Application Idea Followings are list of services which is related to alarm input device connection Thus when you use following features you must make sure that Alarm input device is correctly configured e mail FTP Sensor notification Alarm output device control 4 Alarm Output Relay output device connection FlexWATCH server can easily be interfaced with Alarm output device such as Siren and SSS eee 74 Seyeon Tech Co Ltd Network Video Server User s Manual light Manual or automatic control of alarm output device is supported by the server so that relay output device such as siren light or any output device can remotely be controlled through standard web browser or third party applica
48. configuration 6 Check whether message type is correctly appeared on Result window as below Set Server IP Address ARP Adding static entry to ARP table OK Ping Trying ping 10 10 225 100 OK ARP Deleting static entry from ARP table OK 7 If message come up as below IP address setting has been failed Set Server IP Address ARP Adding static entry to ARP table OK Ping Trying ping 10 10 225 100 FAILED Please check whether IP address and MAC address is valid Then please retry again ARP Deleting static entry from ARP table OK If IP address setting is failed please check whether correct P MAC address is entered And try again with correct P MAC address or please use HyperTerminal method If the above result is O K follow the next step to finish Network Configuration Bee 26 Seyeon Tech Co Ltd Network Video Server User s Manual 8 Click Save IP Address button to save IP Address in the Flash Memory 9 Click Go to Home Page button to access to FlexWATCH Web browser 10 For server configuration click Admin Icon and Input User ID and Password Factory default is root root to get into configuration mode and then press OK button Note Once you changed the IP address of FlexWATCH server you need to connect the server with the changed IP address If you lost the IP address assigned to F
49. d by third party application program and if you want to give different control authority for each camera to different application program you can give different access and control authority for PTZ Audio Relay output device control for specific camera by creating different User account in the server Following is step for Limited access account for each camera 1 Select Limited Access option in the Access Permission menu 2 Click Apply button 3 Click user registration menu in the System configuration section of Admin window 4 Fill out the column provided such as User name ID amp Password 5 Select the Camera module for which you would like to give permission and check control item such as Alarm control PTZ and Audio control L Note default VS Module ID is O and only Default VS Module ID is workable DEE 44 Seyeon Tech Co Ltd Network Video Server User s Manual User Registration Add Add Edit Delete Name Flex WATCH User ID guest Password esses Confirm password System Resource Access Permission Full Access ge 1 Si Gei COOC Mo Access Selective Access Alarm PTZ Audio Enable YS Ge E antral Controll Control o b g S o eil i B o w 2 B C F C o S 3 H a O E C all ull E pack Appi Notice The User ID amp Password must be alpha numeric within 31 charecters Diferent control authority for Camera Alarm PTZ and Audio control can be given to respective us
50. d for the installation of Flex lt WATCH server e Please carefully read this chapter before the installation e Please prepare all the necessary items before start installation to prevent any possible malfunction or any other hazard can be happened during the installation 3 1 Caution and observance e Keep the device in the clean and dried area where air ventilation is guaranteed The device is not waterproof The waterproof device or similar device must protect from any possible hazard by water or heavy moisture etc e Regulated power supply is prerequisite for stable and optimal operation of the device Use only power supply SMPS 12V 1 5Am supplied with FlexWATCH server Manufacturer shall not liable for any hazard or shock caused by use of any other power Supply e To prevent risk of electric shock do not remove system case No user serviceable parts inside Any repair or modification for the product will be allowed to qualified service personal only e Use the cable supplied with FlexWATCH server If you need to connect FlexWATCH server to the other device External Modem PTZ device power on the devices before connect to the FlexWATCH server 3 2 Hardware Description 3 2 1 FW 3110 Hardware Description Front Panel View 16 Seyeon Tech Co Ltd Network Video Server User s Manual Menu Description A DC12V DC 12V power B LAN LAN Port for 10 100M Base T Auto sensing COM RS 232 port for serial input devi
51. d it Note that Pre alarm buffer for Alarm buffering service can be done within the Pre alarm Buffer size Thus you need to count in required pre alarm buffer for alarm buffering service and reserve enough space for this service in the Pre alarm Buffer size 1 1 2 Pre alarm buffer size Pre alarm buffer size Image Buffer Pool means the number of images to be stored and continuously refreshed in the system memory Maximum Pre alarm buffer should be the half size of Memory capacity since Pre alarm images for e mail FTP or alarm buffering service are taken from Pre alarm buffer pool and any Pre alarm image for these services require additional memory space Buffering Service Configuration Total pre alarm buffer size 27690 kb Current used buffer size H frames Chi ch ch3 ch4 Sum Pre alarm Buffer Size ole oie ie unit frametimages o lo lo lo Delay between pre alarm images lo lo fe Ilo leen unt 10 msec Back Save Preyiew buffer configuration Pre alarm Buffer size This is to assign pre alarm image buffer for each camera Once this is configured the Ea OO 80 Seyeon Tech Co Ltd Network Video Server User s Manual maximum number of pre alarm for e mail ftp or Alarm buffering service Pre alarm only can be done with this buffer size if there is enough memory space for respective services Note that there must be enough memory space left for e mail fto and Alarm Buffering service Pre alarm
52. e you need to upgrade some specific file only Following is brief explanation about the file system for FlexWATCH server Files Size unit KB Description Kernel file Game as Os in the e ker_xx window e_rfs_xx gz Root file system System file Application e_sys_xx tar gz software in the window Web file Web server of FlexWTCH server Note depending on the hardware initial of each file can be different e_web_xx tar gz You can download the latest version from Downloads menu on www flexwatch com www seyeon co kr file size will be different in each version In addition to above 4files PTZ device driver and Sensor Device Driver module can separately uploaded into the system through web browser dea El 99 Seyeon Tech Co Ltd Network Video Server User s Manual System Update All Firmware RAM disk System Web Update Start System and Web Update Start Web Only Update Start PTZ Device Driver Update Start Sensor Device Driver Update Start Back System Information Web Version 3 0 Build 2004 10 25 Firmware Version 3 0 Build cU04 00 04 Serial Number O0 30 6F 63 00 01 All kernel RAM disk System Web Update To completely update all the system for Kernel RAM Disk System and Web all together except PTZ Device Driver or Sensor Device Driver This option is recommended if there is special notice by manufacturer Generally complete system update com
53. ectory name Multiple directories can be created in the Base directory so that ftp image can be stored in a Classified directory Once you select Directory name filed and click Make Directory button multiple sub directories will automatically be created in the Base directory according to selected option Only one directory option among the multiple options can be selected Example If you select Weekday option in the filed and Based file name is flexwatch server following sub directory will automatically be created flexwatch server Sun Mon Tue Wed Thu Fri Sat File name File name will automatically be created with the prefix the Base file name Multiple file name option field can be selected at the same time In this case each Field is concatenated sequentially But total length of file name is 32 characters including based directory name 4 1 2 Directory option for Periodic FTP Duration Service Configuration of Directory option for periodic is same as those of buffered service The only difference is that there are Sequence Modulo and Overwrite option in the option filed Sequence Modulo This is used when some number of ftp images should be stored and refreshed as new ftp images are stored in the ftp server By setting up Modulo number for sequence you can Ree 91 Seyeon Tech Co Ltd Network Video Server User s Manual limit number of image to be stored and refreshed If you set i
54. eeeeee eee eeeeeeeeeeeeeeeeetenes 54 4 3 Dial Out Seite Teen 55 4 4 Dial in Configuratio EE 57 D Service Path 58 AOIP Setup 59 6 1 How to use AOIP service 59 6 2 AOIP Seine ege EE 60 T Network Status 61 External Device connection amp Confguration e 62 L Serial Ports CONTGUFAUION e e 62 1 1 Hardware De PION aeee a E EAE EEEE ERN 62 2 Installation amp Configuration of External Device sssseserrerererrrrerrrrrrerrrrerrrrne 65 2 1 Console Hyper Terminal cable connection ssssesererrererrerererrrrererrereree 65 2 2 Serial visite EE 66 2 3 Serial OUREA VIC e 67 2 4 PTZ device connection and Seille fe Late E 69 2 5 Voice Kit Connection and Sai biet leg e TEE 72 ue eaa 4 Seyeon Tech Co Ltd Network Video Server User s Manual 3 Alarm input device CONNECTION ccc cece cece cece eee ence eee eeeeeeeeeeeeeeeteeeeeeeeeeeeeennas 74 4 Alarm Output Relay Output device Connechon ccc cece eee eeeeeeeeeeeeeeseneeaes 74 4 1 Alarm output device Connection 75 4 2 Manual control of Alarm OULOUT C6 TER 75 4 3 Automatic Control of Alarm Output device 76 Advanced Service configuration EEN ENEE ENEE ENEE ENEE EE EE E EEN 78 1 BUTFErING Service 78 1 1 System and Pre Alarm Buffer memorn cece cece eeeeeeeeeeeeeeeeanenaes 79 1 2 Buffer calculstor innr tr ntre rreri rrr r ninr err narenn enn 81 PAIE Aa 83 2 1 Condition E SE 84 2 2 Criteria Re DEE 85 3 e mail CONTIGUIATION EE 87 3 1 email function COMING Ua U
55. er Check appropriate box to give control authorizty Full Access If full access is selected any body can access the server and control the video No Access This is to temporally restrict camera access by specific user without delete user account to temporally block access to the camera Selective Access This is to set up control authority for the respective or all cameras VS Module ID is FlexWATCH server ID which is recognized by the server Default is O Please disregard other VS Module ID appeared in the drop down menu Other module numbers is for future use which is not currently workable Camera number start from O which is the first camera connected to BNC connect 1 ue eaa 45 Seyeon Tech Co Ltd Network Video Server User s Manual Thus 4 camera can be Camera 3 in this menu 5 Frame rate control Maximum Video frame rate which sever can transmit over the IP network can be set up through Frame rate control option Through this maximum frame rate control option user can limit network bandwidth consumption by video transmission 1 Go to Access Control option in the system configuration menu in the Admin page 2 Set up Maximum frame rate Following table could be an example File size is variable depending on the complexity of the scene Thus it hard to get exact and fixed number of file size Access Control Configuration Access Permission GG Full Access View and control camera amp voice w
56. es only when there is big change for all of the system software System and Web Update To update system and web related software together This update can be common to update the system Web Only Update To update only Web page of the server This is useful to uploaded customized web page only to save update times E 100 Seyeon Tech Co Ltd Network Video Server User s Manual PTZ Device Driver PTZ Device Driver is already built in the system But if there is a new PTZ Device driver Supported by the system it can separately uploaded into the system without other software change Sensor Device Driver Serial input device driver can separately be uploaded into the system so that independent Serial input device can work with FlexWATCH Server 4 2 Update Procedure Step by step procedure is provided by the system which means each file will separately uploaded one by one Please make sure that all the system files to be updated reside in your PC before starting update 1 Go to Utilities column and select System update option 2 Select option provided in the system update window and click Start button System Update All Firmware RAM disk System Web Update Start System and Web Update Start Web Only Update Start PTZ Device Driver Update Start Sensor Device Driver Update Start Back System Information Wiel Version 3 0 Build 2004 10 25 Firmware Version 3 0 Build 2004 0
57. exWATCH server is connected to LAN network you can assign IP address through program and access the Web browser HyperTerminal mode If no network is available and you want to set up IP address you can directly connect FlexWATCH server to your PC through Serial cable provided together with product HyperTerminal mode is very useful tool to recover Admin password when you lost your admin password or to report any problem to Manufacturer when product is on malfunction status 4 1 Through Installation Wizard Program IP setting with Installation Wizard program is easy and simple way and after IP setting is done you can do other configuration through web browser eee 24 Seyeon Tech Co Ltd Network Video Server User s Manual You can use IP Installation Wizard Program through following step IPI nstallationWizard exe is provide in the product CD Preset a PC with Microsoft Windows O S 1 Connect FlexWATCH server into the network Hub that your PC belongs to 2 Run the IP installation Wizard program in your PC Then following IP Installation Wizard window will show up CIP Installation Wizard E x Seral Number MAC Address of System e neice al Wl bal Set IF Address C WAN For Assign IF Address for System save IP Address IP Address on PL 10 70 207 759 IF Address 10 10 226 100 Subnet Mask 255 255 0 0 Default Gateway Th mp Tt gt D gt E LARP Adding static
58. g 3 1 1 Image encryption Image encryption is security feature to prevent unwanted image hacking when anonymous user accesses the system Once it is enabled user must enter encryption code to view live video 1 Simple set up encryption code 2 Enter encryption key code to view live Up to 8 alpha numeric characters can be used Enter JPEG encryptio Eg ZS Note Once you lost your encryption code you can reconfigure encryption code through Admin Mode Once I mage encryption is enabled FW Manager can not display live video Thus you must disable Encryption mode when the image is to be viewed from FW Manager program 3 2 Camera configuration Through camera configuration mode you can adjust the video quality to meet your requirement 1 Click Camera configuration menu in the Service configuration mode of admin window 2 Set up camera value string 3 Select Camera channel and set up camera related information such as Camera name and quality setting ees 37 Seyeon Tech Co Ltd Network Video Server User s Manual Camera Configuration Camera Number 1 Camera Name Camera 1 Camera Install Enable Disable Camera Mode Color Gray Image Size 352x240 NTSC 352x288 PAL ei Image Quality Normal K Hue os f 100 100 Saturation o f 100 100 Contrast D f 100 100 Brightness D 100 100 Motion Detection 4rea Select Area Motion Sensitivity
59. h p Video ott TU A 2 3 2 Static IP address from Cable modem or xDSL line Simply get a Static IP address from Network Administrator or ISP and assign IP address to FlexWATCH server and view from the Internet DoI I I UUO O 12 Seyeon Tech Co Ltd Network Video Server User s Manual Static IP from Cable Modem xDSL Trawel 2 3 3 Dynamic IP address from Cable or xDSL line FlexWATCH server can be installed on even Dynamic IP network But it needs to be registered in AOIP server which is an IP gateway running by Flexwatch com or your local Distributor For more details please refer to Technical guide book in the CD manual Global Dynamic PP from Cable Modem 2061 CCD camera Loop Through e Video output TE i a CTL Ta eo Register ideo server in ADIP Server Kiss Assign Private IP to FlexWATCH exer Dice Mella Client get connected to Video server through ADIP server Travel ADIP acts as IP gate way 2 3 4 Dial up to AOIP server Using Dial up function of FlexWATCH server and AOIP service you can set the FlexWATCH server to make a call to ISP and get it connected AOIP server Once FlexWATCH server is registered in AOIP server you can connect FlexWATCH server through AOIP server Using this connection you do not need to make multiple call or international call to FlexWATCH server since FlexWATCH server will be connected by 13 Seyeon Tech Co Ltd Netwo
60. here is not other setting to be changed in the network works configuration except DNS info if required 2 1 1 11P notification by E mail service You can receive IP address of the server through e mail from the server when the server is connected to DHCP server Please do not enable DHCP client feature till you open a way to receive or get I P address of server 1 Check whether you are in the DHCP environment before starting set up 2 Go to Network Status Notify menu in the network configuration mode 3 Set up e mail account through which you would like to get IP address information when the server is set up DHCP Client Network Status Notification Mail Notification Enable Disable SMTP Server kornet net Authentication Login Enable Disable User ID flaxwatch Password as Sender luser 1st Recipient luser flexwatch cam 2nd Recipient 3rd Recipient IP Address from flexwatch 4 Now go to Network configuration mode and select DHCP option For more information about e mail configuration refer chapter for the e mail DEE 51 Seyeon Tech Co Ltd Network Video Server User s Manual configuration in Advanced Service 2 1 1 1 Server access through AOIP server Once Server is registered in the AOIP server and DHCP is enabled you can access the server through AOIP server IP address of server can be found from AOIP server as well In this case you do not need to configure e mail address sett
61. ically given to remote client PC by FlexWATCH server when FlexWATCH server is connected by remote client PC using dial up networking This IP address 192 168 2 2 is for data communication between FlexWATCH server and Remote client PC So you do not need to change this IP address But if you change default IP address of FlexWATCH server 192 168 2 1 for modem connection to different class of IP address you need to change remote IP address to the same class of IP to match the IP class L Note that when Local IP address is change remote IP address should be changed into the same class of the IP address 5 Service Path This is to specify service path through which server can send any information to target device 1 Go to Service path menu in the service configuration mode 2 Select Modem if any data should be sent through PSTN or external modem device and click Apply button EP O 58 Seyeon Tech Co Ltd Network Video Server User s Manual Service Dial Out Path Configuration This is to select service path to send any data through modem connection only Service Dial GQut Path Monel Lan O Modem Gi sg Set Notice Modem connection will be automatically disconnected if there is no data transmission through this connection for a couple of minutes LAN This is default path the send any data to outside Modem when PSTN or other medium than LAN is used to send data to outside This serv
62. ice port must be checked when any data is to be sent through PSTN or other medium than LAN which is connected to COM port ZS Note Service path must be set up and checked before starting WAN configuration to send any data through external PSTN modem connection or equivalent If LAN is to be used select None LAN option 6 AOIP Setup AOIP Always On IP is an IP gateway through which user can access the FlexWATCH server when it is connected to Dynamic IP address Thus if the server should be connected to the Dynamic IP network and you want to view live video from anywhere it is the right solution for you 6 1 How to use AOIP service Following is a step you need to take to use AOIP service Contact your local vendor or sales flexwatch com to get user account for AOIP service Register product in the AOIP server under your account Set up your network Port mapping function of your router Enable AOIP service option in the FlexWATCH server ee 59 Seyeon Tech Co Ltd Network Video Server User s Manual Once things are set up you can login to AOIP server and connect your FlexWATCH server ZS Note AOIP is proprietary data service run by FlexWATCH or its business partners around the world Thus depending on the country AOIP service can run by your local vendor or master distributor or in some case you need to user AOIP server run by manufacturer More detailed information about how to use can
63. ing to get IP address from the server Please contact your local vendor or manufacture to get more information about AOIP server which is an IP gateway for Dynamic IP user 2 PPPoE Configuration Some DSL or Cable Modem based ISP provides PPPoE based internet connection service If FlexWATCH server must directly be connected to the external DSL or Cable modem PPPoE option must be enabled Note that you must open a way to get IP address information since there is no way you can get to know IP address of the server through web browser when the server is set to PPPoE network The only way you can get IP address is through e mail or AOIP server Please refer to above DHCP client part to set up e mail and AOIP connection PPPoE Configuration Service Enable fe Disable User ID User Password Confirm Password DNS1 168 126 63 1 DNS2 168 126 63 2 Back Apply Please contact your local I SP to get User ID and Password for your I nternet connection amp Note Ce eee 52 Seyeon Tech Co Ltd Network Video Server User s Manual Once PPPoE is enabled LAN network setting will be disabled 3 Network port configuration HTTP port NVCP and VDCP ports are application port through which video and audio data can be transmitted over the TCP IP network Network Ports Configuration HTTP Port GR Default 80 80 65535 NWOCP Tx Port 50200 Default 50200 10000 65535 YOCP Port 32001 Default 320
64. itec ET 50 USA Ba 7 Select the installed PTZ Model on the dropdown menu as above 8 Select the Channel number installed with the PTZ and click Apply button 2 4 2 Supported PTZ Pan Tilt Zoom Device list e Following is list of PTZ devices which are directly supported by FlexWATCH server Note that some of PTZ has not been field approved although manufacturer integrated its protocol into FlexWATCH server Thus it is highly recommended for you to use only field approved PTZ device e In addition although Manufacturer integrated Protocol of PTZ device and did field test PTZ can not be workable since PTZ manufacturer can change its protocol or other functions Thus it is highly recommended for you to contact your distributor or sales flexwatch com to make sure its connectivity through FlexWATCH server e You are also required to refer to Technical note for installation guide per respective PTZ device in the CD manual Supported PTZ List by FlexWATCH Server a ee 70 Seyeon Tech Co Ltd Network Video Server User s Manual Comman Auto Program Field _ Cane sem fete e Teme sees wo fe ee Trew wesw e fe S e n owen as e es ae sme es fete l e sone seen ms fefe 7s e Tse wom fs fet e Teen ore e fe sen ose ws f efe e Tower ee a fefe ep ven wm fs fepe e wen seer as pe e Tae ow pepe om a e e e ane e ws e 0 rm sons fs fe fe
65. ithout permission Limited Access In accordance with an user s permission Frame Rate Control Maximum Frame Rate 30 fps sl Back Apply oy rate requirement i ee File Required Bandwidth mnz E E Fe NTSC 8KBps 640K bps 1 6Mbps S 20KBps 1 6Mbps_ 4Mbps_ 173X114 4KBps 320Kbps 800K bps 352X 288 10KBps 800K bps 2 0Mbps 704X576 25KBps 2Mbps 704X 576 Above file size table is average file size manufacture got from the lab test Formula to calculate required Bandwidth File Size x FPS X 8 bits 3 Click Apply button 46 Seyeon Tech Co Ltd Network Video Server User s Manual 6 Tx Module Registration NVCP Notice If you do not connect FlexWATCH server to NDVR server do not set TX module configuration Once Tx Module configuration is done set up RX module configuration in the NDVR server as well Video proxy function is supported by NDVR server such as FW 5440 and FW 5000 server By registering FlexWATCH video server into NDVR server live video can be recorded in the NDVR server and live view can be accessed through NDVR server web page which means user does not need to separately run web browser to view respective cameras from FlexWATCH video servers TX module registration is to set up the FlexWATCH server to communicate with FW 5440 or FW 5000 NDVR server or FW VSS Proxy Server only When TX module is enabled at the FlexWATCH server RX
66. lexWATCH server you need to set up a new IP address again r Note If IP address set result is failed please check whether correct IP MAC address is entered And try again with correct IP MAC address or please use HyperTerminal method 4 2 IP Assignment through Hyper Terminal mode Microsoft Windows provides Terminal emulation program namely Hyper Terminal For HyperTerminal connection Power RS 232 Cable and LAN cable must be connected to FlexWATCH server with user s PC LAN cable is to run Web browser after configuration using HyperTerminal You can continue the below configuration after Network setting and the next process will be same as using Installation Wizard Program 1 Link up with the provided serial cable between COM port at FW 3440 and COM1 or COM2 at user s PC 2 Run Hyper Terminal Program on user s PC Window start gt Program gt Accessories gt Communication gt Hyper Terminal d Le Accessibility j Le ATI Multimedia Center dES Communications ka Accessories FivvoyagersP For Internet Explorer e Entertainment Th HyperTerminal E Internet Explorer Le Games ae Internet Connection Wizard Microsoft Access Le Microsoft Script Debugger Es NetMeeting Microsoft Excel System Tools V Network and Dial up Connections Microsoft FrontPage EEN Address Book Phone Dialer 3 Microsoft Outlook EA Calculator HyperTerminal 3 If Hyper Terminal window come up as below input HyperTerminal name
67. load and install FlexWATCH Simple Viewer control program Click Live view tab in the web browser Click Yes button when security Warning panel come up Then live view will be displayed SSS eee 32 Seyeon Tech Co Ltd Network Video Server User s Manual SW Warning a xjl Ba you want to install SE run Fl TEH SimpleViewer Geen Of an ukoum SE distribute Publisher authenticity verified by Thawte Code Signing EA Caution Se e Te eh Con Ltd asserts that this content iz gate Vou should SC install view this content if you trust Seyeon Tech Co Ltd to make that assertion Always trust content from Seyeon Tech Co Lid e Il mes When the Client pc is not connected to Internet you need to manually install Activex components in your viewing PC Insert the product CD in your PC Select FlexWATCH Simple Viewer control program ZE Application idea ActiveX based SDK is provided for software developers so that application program developers can easily utilize digital video from FlexWATCH server for his own video application 1 2 Java Applet based live view Java applet is to display live video through any web browser on any Operating system Supporting J ava Virtual Machine This is to view live video through Netscape navigator on MS window or other Operation system such as Unix Linux MAC and OS2 Thus if you are using MS IE on MS Window Java Applet can not be e
68. n detection feature below Time stamp Date and Time information can be engraved in the JPEG Image It is recommended to use time stamp only when you need image with built in time info L Note that once Time stamp is enabled over all transmission speed can be degraded 3 3 Video Motion Detection Built in motion detection function is supported by the FlexWATCH server so that server can sense the motion in the picture and trigger any services such as e mail FTP or alarm buffering services Up to 144 square blocks can be configured as a motion area so that you can flexibly filter out motion area 3 3 1 Setting procedure 1 Go to Camera amp Motion option in the Admin Menu 2 Select the camera for video configuration 3 Click Select Area button from the Camera configuration menu 4 Click the square block to set up motion detection area 5 Adjust Motion sensitivity the lower the number the higher the motion sensitivity 6 Check Motion Enable check box and Click Apply button to save your configuration SSeS 39 Seyeon Tech Co Ltd Network Video Server User s Manual EE Flex WATCH Administration Microsoft Internet Explorer E LD xj System Configuration gt gt System Information gt gt Date amp Time Video Channel Configuration gt gt Admin Password Access Pe
69. n detection function in the FW Manager Simply configure motion detection for the selected camera in the FlexWATCH server Set up Motion based recording condition in the FW Manager Do not set up motion detection area in the FW Manager software E 41 Seyeon Tech Co Ltd Network Video Server User s Manual System Configuration System configuration is to set up basic functions which help you properly run and manage the system It is highly recommended to set up the configuration before any other configurations Following functions are provided in the System configuration mode System name and Info System Administration account set up System access level setting Serial port configuration PTZ or external device connection TX Module configuration 1 System Information System information is very important one Following menu will be provided User definable and Identifier of the system when the system is accessed by third party program such as NDVR software Serial Number Product serial number This information must be submitted for RMA or Warranty claim This information also needs to be submitted for technical support request System firmware version This information also needs to be submitted for technical support request 2 Date amp Time Date amp time Is very important factor to trigger any service at the right time such as FTP e Mail Alarm notification etc If Date amp time is not correctly set
70. nabled Note that J RE Java Runtime Environment must be running in your web browser to display live video on Unix Linux Mac OS2 Operating system or Netscape Navigator on Window If not you need to manually download and install J RE file from the web page of Sun Microsystems 1 3 Live view page guide Simple viewer page provides various control option such as image magnification full Ree 33 Seyeon Tech Co Ltd Network Video Server User s Manual screen snapshot PTZ control Relay output control Voice kit connection as well Moliaelt 9 your remote eye e surveillance leader Module Selection Ir OJLocal Device O Local zl Cam Control M Cameral lf Camera 2 IT Camera3 Camera 4 Al _None Frame Ratel fastest D OO Sequence On il Pause Snap xi x2 Be Voice gt DO PTZ Control Cam Control By checking the camera you can get any number of camera displayed on the same screen Camera 1 2 3 4 and all cameras can be displayed together Sequence To view camera selected camera sequentially Frame rate You can adjust display frame rate by control Frame rate option Display size X1 for Real size x2 for double size and Full screen mode is supported Snap shot You can make a snapshot of video while viewing the live video Voice When the voice kit FW V10S is connected to the FlexWATCH server you can Simultaneously listen and speak with your counter part through web
71. ne buffering Service its directory option is SSS eee 89 Seyeon Tech Co Ltd Network Video Server User s Manual Slightly different 4 1 1 Directory option for Buffered FTP Buffered FTP means that only pre post alarm buffered image will be sent to FTP server when the ftp is triggered by the event FTP function of FlexWATCH server has two different level of directory and file name option and following are details FTP Buffered Service Configuration Service Enable Disable Server Address 10 10 212 28 Base Directory Name flexwatch server Base File Name User ID flaxw atch Password eee Option Directory Name File Name weekday E F Month L Day L ad Hour C a Minute IT Sec d Sequence F Video Channel E C Back Make Directory Base Directory Name Base directory is a path where ftped image will be saved in the FTP server Directory name can be made under ROOT or Home directory of FTP server If you select directory name in the option filed above sub directory will be created under the Base Directory If you do not select Directory option and select File Name option filed only file name will be created with combination of Base File Name in the Base Directory Base File name SSS 90 Seyeon Tech Co Ltd Network Video Server User s Manual User defined prefix of file name of each image File name of FTP images will automatically be concatenated after prefix Base File name Dir
72. p the connection with AOIP server not terminating the connection with ISP Thus you can quickly connect the server through AOIP server and view live video The key benefit of using AOIP connection is to view live video without making a separate call to FlexWATCH server whenever there is alarm and you can easily access the server If you are running FW Manager software live video will be automatically display on the FW manager screen when there Is any alarm 4 3 Dial Out configuration This is to set up the system to make a call to ISP when the dial out condition is activated to transmit live video or send e mail or FTP image 4 3 1 Dial up through Standard modem Dial out through standard PSTN modem is quite common and general 1 Connect the server to PSTN line through RS 232 cable Connect the cable to COM Port or server Use the standard D Sub 9pin connector provided by PSTN modem 2 Go to WAN PPP Modem etc menu in the Network configuration mode 3 Select PPP client option and fill out the option field DE 55 Seyeon Tech Co Ltd Network Video Server User s Manual WAN Modem PPP Client Dial Out PPP Server PPP Client TEL lo 1414 User ID syta 1000 User Password Confirm User s Password Jesse Default Route DNS 168 126 63 1 DNS2 168 126 63 2 Back Reset PPP Client This means that FlexWATCH server act as client and call out to ISP PPP Server This means that FlexWATCH
73. password is nvcp The new password automatically replaces old ane If the NWiCP passord is changed that nvco password should be assigned to NWR server Otherwise no communcation can be set up between the devices Please click the below link to configure Tx Module Tx Module Tx module Name Connection Type IP Address MAT Address Tx Module 0 Passive Mode O0 30 6F 00 00 00 Tx Module 1 Passive Mode O0 30 6F 00 00 00 Tx Module 2 Passive Mode O0 30 6F 00 00 00 Tx Module 3 Passive Mode O0 30 6F 00 00 00 Tx Module 4 Passive Mode O0 30 6F 00 00 00 Tx Module 5 Passive Mode O0 30 6F 00 00 00 Tx Module 6 Passive Mode O0 30 6F 00 00 00 Tx Module 7 Passive Mode O0 30 6F 00 00 00 Tx Module 8 Passive Mode O0 30 6F 00 00 00 Tx Module 9 Passive Mode O0 30 6F 00 00 00 Tx Module 10 Passive Mode O0 30 6F 00 00 00 Tx Module 11 Passive Mode O0 30 6F 00 00 00 Tx Module 12 Passive Mode O0 30 6F 00 00 00 Tx Module 13 Passive Mode O0 30 6F 00 00 00 Tx Module 14 Passive Mode O0 30 6F 00 00 00 Tx Module 15 Passive Mode O0 30 6F 00 00 00 Back Apply Ts module registration is to set up the server to transmit video streams to external device such as FY 5440 or 5000 HMR server over the TCP IP network Video can be transmitted up to 16 different external devices simultanously 3 Select TX Module By configuring TX module you can program the server to communicate with different NVR servers Up to16 different NDVR servers can simultaneously work with FlexWATCH
74. pending on the memory used by the system Preview buffer configuration Chi ch ch3 ch4 Sum Rate rao 72 9 df 21 Pre alarm Buffer Size 150 150 200 200 Pre alarm Je IS is lb Email Service e Post alarm 5 5 5 EW dl l 140 Fre alarm Ian 30 40 KE 14 6 FTP Edge Service ap Post alarm Ian 20 20 Eg 5 3 cumRate 212 210270270 960 um Rate a oun 281 281 99 999 Chi ch ch3 ch4 Sum Rate FOO Pre alarm 150 150 200 200 Alarm Buffering 413 6 Service 700 y Post alarm 150 200 200 48 6 ue 0 30 400 400 1400y um Rate an oun 278 278 972 Sum Close Total number of Pre Alarm Post Alarm for FTP per channel lt 256 frame Total number of Pre Post alarm for e mail per channel lt 10 frames for channel Pre alarm frame for FTP amp e Mail and Alarm buffer service shall be done within Total pre alarm buffer size Post alarm for FTP amp e mail has nothing to do with Total buffer size Post alarm for Alarm buffering service can be done within the Memory allowed by Alarm buffering service size The ratio of sum in the Buffer Calculator should be less than 100 1 Go to Advance service mode in the Service configuration section ue eaa 82 Seyeon Tech Co Ltd Network Video Server User s Manual 2 Go to Buffering service mode 3 Click Buffer Calculator button to run the calculator 4 Pre configure pre post alarm buffer fo
75. r Server reboot and Serial device activation or combined activation can be recognized as an event a 85 Seyeon Tech Co Ltd Network Video Server User s Manual Event 1 E 4 5 6 Input Open State BI P Input Close State EI EI Motion Detection Camera Connected EI EI EI Camera Disconnected DI P EI E Boot Finished Enable Serial Input Lol Activated Event number can be mapped as a Sensor port and camera number DI Open State This means that sensor is triggered and become open status from Normal close status Select this when you use NC Normal Close type sensor DI Close State This means that sensor is triggered and become close status from Normal open Select this when you use NO Normal Open type sensor Motion Detection By selecting this option motion detection based event can be configured Camera Connected and Disconnected Camera status change by lost of camera signal can be recognized as an event Boot Finished Boot finish means Server reboot Thus when the server is rebooted it can be recognized as an event Serial input FlexWATCH server can carry serial data along with video When serial data from external serial device is activated this can be recognized as a event Sensor state means when the sensor status is Open or closed If you use NC Normal Close type sensor and activate any action when sensor Is open you need to select Open State and vice versa when you use NO Normal Open
76. r RS 232 is already AUX COM assigned or not and use different part for RS 422 RS 485 ee io connection which is not assigned by RS 232 Port 123 45 678 EE EE ER E TX TX RX RX TX TX RX RX When you select PTZ at AUX part AUX make use of Pin No 1 and 2 from RS422 485 port When you select PTZ at COM part make use of Pin No 5 and 6 from RS422 485 port When you install a RS 232 interfaced PTZ model PTZ device has to be connected to AUX or COM Port with RS 232 Serial Cable Standard RS 232 cable can be used to connect AUX or COM port 1 Connect your PTZ device into RS232 COM or AUX port as above explanation Re UUO 69 Seyeon Tech Co Ltd Network Video Server User s Manual 2 Goto Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 3 Select PTZ at COM or AUX mode and click Apply button 4 System reboot will be recommended then click Reboot button 5 After rebooting Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 6 Click PTZ Mode then following window will show up PTZ Mode Configuration Current Port AUX Current Protocol R5232 PTZ Model Not Installed sl Not Installed af Install Flag sm ID Pelco Pelco D USA N 91Ch3 ch4 Pelco Pelco P USA T T KALATEL CyberDome USA Vicon V1311RB USA Vicon Survey Dome USA Sensormatic 4D Dome USA Panasonic WV CS 854 JAPAN e d SONY EVI D30 JAPAN CANON VC C4 J4PAN Ern
77. r each service This previous window can be open till you manually disclose the Window Thus you can refer to this table when you configure e mail ftp or Alarm buffering service configuration 2 Service Condition Sophisticated advanced services can be done by lots of serviced conditions provides by the system To correctly set up the system use must has good understanding about the service condition as well e mail FTP Sensor notification and Alarm output device control function requires service condition set up to activate the function Note that the basic logic for the service condition set up is same for all of other options E 83 Seyeon Tech Co Ltd Network Video Server User s Manual Condition 1 Service E mail Module ID 0 amera UU Enable Disable O Always Condition Setup Select Mode Schedule Only Event Only Schedule and Event Schedule i Sun Mon Tue Wed Thu Fri Sat Wee al A Date mmidd 3 01 jog lad Event Input Open State Input Close State Motion Detection K O k Is O k fs K A fs Is LI Camera Connected O K bgi aS ao Camera Disconnected Boot Finished Enable Serial Inout Activated pack D ss 2 1 Condition Setup This is to define basic condition to activate any option selected Select right condition from the option provided Always To active any selected option regardless condition If you select this condition Schedule
78. r from remote client 3 Check Authenticate more as none 4 Configure User ID and Password if you need to set up authenticate mode 5 Click Apply button and quit configuration menu WAN Modem PPP Server Dial In PPP Server PPP Client Local IP Address 192 168 2 1 Remote IP Address 192 168 2 2 Authentication Mode O PAP CHAP G NONE User 1 Wer o y y Password User 2 ID Password User 3 Df Password Back Apply Reset Local IP address and Remote IP address When remote client is connected to the server through modem connection physical line connection will be done But no way to view live video unless client runs the web browser 57 Seyeon Tech Co Ltd Network Video Server User s Manual of the FlexWATCH server Local IP address and Remote IP address is virtual IP address which is used at the time of Modem connection only Local IP address System default IP address 192 168 2 1 resides in the FlexWATCH server for modem connection only So when you connect the FlexWATCH server from remote PC using dial up networking and physical connection is made you need to run your web browser and enter this system default IP address 192 168 2 1 to view live video You can change this system default IP address as well But it is recommended not to change system default IP address for modem connection to prevent any possible error Remote IP address IP address which is automat
79. ration gt gt Serial Ports Configuration 3 Select Serial Output at COM or AUX mode and Click Apply button 4 System reboot will be recommended then click Reboot button 5 After rebooting Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 6 Click Serial Output Mode then following window will show up E 67 Seyeon Tech Co Ltd Network Video Server User s Manual Serial Output Mode Configuration Current Port None Line Mode R5 232 sl Baud Rate 35400 Data Bit Io sl bit Stop Bit fi pm Parity Bit None sl Mode DG By Pass x10 z256 Back Apply an Sample Page provides an example how to output data through serial part G After setting up the parameters in the each filed click Apply button Note that if you are using X10 device protocol you do not need to set up parameters but simple select X10 Enable option 2 3 2 X 10 device amp Z256 X10 and Z256 is a protocol name of Device which is to control electronic devices over the Power line communications Using this control mode you can build up a system to control any electronic device over the TCP IP network through FlexWATCH server This function is highly recommended for Home automation or remote device control application This function is not for general use Thus if you need more se information about this please contact your local distributor or manufacturer for fur
80. rk Video Server User s Manual your local Phone line based Internet connection Digi Gut connection using ADP Sernice CCD camera Loop Through Video output Raphita Hip tora OP denver Rec TCH make a cal ogtto BP Tor the OR CoC aria g ator ioe ie Lhe 34k BTS St Cognac at fh ed charge 2 3 5 Dial in to FlexWATCH server through PSTN line You can make a call to FlexWATCH server from anywhere and at anytime But if you are concerned about call charge we are recommending using above connection Dian comecton from PC ToD camera Loop Through Wide output 2 4 Application Unlimited application for remote monitoring and surveillance solution can be built up using FlexWATCH server and its supporting peripheral Hardware and software such as FW 5000 or FW 5440 Network video recorder server and FW Manager DVR software Following could be simple application area where FlexWATCH server can be applied A Building live home pager for advertising 44 Seyeon Tech Co Ltd Network Video Server User s Manual B ITS Intelligent Traffic System for real time monitoring C IBS Intelligent Building System using FlexWATCH Manager D Internet broadcasting E School Kindergarten Nursery Franchised Restaurant amp convenient store F Facility monitoring 15 Seyeon Tech Co Ltd Network Video Server User s Manual 3 Hardware Description e This chapter contains list of items to be prepare
81. rk device in the private IP address can be added from Internet Hub Hub is a hardware which relay transmission between Router and Network device There are two types of Hub One is Dummy hub and the other one is Switching hub Note that Hub will be used in the local network only NAT Network Address Translation Network Address Translation NAT translates multiple IP addressed on the private LAN to one public address that is sent out to the Internet This adds a level of security since the address of a PC connected to the private SSS eee 19 Seyeon Tech Co Ltd Network Video Server User s Manual LAN is never transmitted on the Internet AOIP Always On Internet Protocol Server AOIP server Always On IP is run by Seyeon Technology or its business partner and is a gateway for remote users to access FlexWATCH servers which is connected dynamic IP address over DSL Cable modem and PSTN network over the Internet FlexWATCH Network Video Server and Camera Server family is fully supported by AOIP server and any type of IP address Global Dynamic IP or Private IP can be assigned to FlexWATCHTM server and user can access FlexWATCH system from the Internet at anytime and anywhere through AOIP server 2 Check Points before IP assignment Following are list of item to be checked before you start configuration of FlexWATCHTM server 2 1 IP address You need to have Static IP address and other information such as Defaul
82. rmission Channel Number 1 EE Channel Name Camera 1 Rx Module Registration Channel Install Enable Disable Network Configuration esis UNE Color C Gray gt gt LANCIP address Image Size 352x240 NTSC f 352x288 PAL z gt gt Ee ele Image Quality Normal sl gt gt Por apping gt gt Network Ports Hue o 100 100 WAN Modem Saturation 0 100 100 gt View Network Status Contrast o 100 as 100 o gt Network Status Notify S s AOIP Setup Brightness IW 100 100 NTP Setup E SST l A Service Configuration a eee ET ise gt gt Service Dial Up Path Kei L 000 Video amp Motion L JL J TEE Input Output z E Alarm Outpu ontro a eee ee l nS E d Motion Detection Area Welt Configuration Kal Car IIe HDD Configuration Ca eae Recording Configuration 7 e e BAA gt gt Recording Mode ES vn Disk Email Notification E eS le gt Clear Recording Config Check All Uncheck ll gt gt Delete Recorded Data Motion Sensitivity o_ 100 100 100 is hypersensitive Utilities Motion Enable Enable Disable gt gt Flash Update gt gt Reboot Time Stamp C Enable Disable gt gt Factory Default System Update BOGE Default E f 4 3 3 2 How to save Motion triggered image in the NVR solution Recording in the FW 5440 5000 Simply check Motion Detection option in the recording condition menu in the FW 5440 or FW 5000 when motion detection option
83. t Gateway and Network Mask which are to be assigned to FlexWATCH server Please consult with your network administrator if FlexWATCH server is to be installed in your corporate network or consult with ISP if you want to install it in your home or shop for which DSL or Cable modem Internet service is available Following could be a simple way of finding IP address information of your PC and with that information you can set up IP address to FlexWATCH server in the private IP network without consulting to your ISP Open DOS Command window as following procedure Program gt Accessories gt DOS Prompt Enter ipconfig command Following information will come up 2 1 1 Static IP address enabled PC DHCP Disabled PC You can easily check whether Static IP address is assigned to your PC If you are in the Static IP network it is simpler to assign IP address to FlexWATCH server than DHCP EE 20 Seyeon Tech Co Ltd Network Video Server User s Manual network C gt ipconfig Windows 2000 XP IP Configuration Ethernet adapter Local area connection Connection specific DNS Suffix IP Address Subnet Mask 255 255 255 0 Default Gateway gt 192 168 0 1 With above info you can get information about your network from your PC and see which IP class of IP address should be assigned to FlexWATCH server Note that the same class but different IP address appeared in your PC
84. t Protocol address which allows all network devices can communicate other over the network using Internet protocol Each network device has its own unit IP address whether or not it is in the LAN or WAN network Therefore network devices can be accessed by other network device from either LAN or WAN Internet For example www yahoo com is a web server which has its own IP address so that any body can has access to Yahoo web site Like most of public web site has its own IP address Although IP address can not be seen by the client domain name www yahoo com is automatically converted into IP address by DNS server Static I P address A static IP address is an IP address permanently assigned to computer or network devices in a TCP IP network Static IP address is usually assigned to network devices which are consistently accessed by any users For instances www yahoo com has global static IP address Thus any body can access to the site If you want to view live video stream from FlexWATCH server over the Internet you need to assign Global Static IP address Depending the network Public Static P WAN or Private Static IP can be assigned to network device SSS eee 18 Seyeon Tech Co Ltd Network Video Server User s Manual Dynamic IP address A dynamic IP address is an IP address that is automatically assigned to a client station computer network equipment etc in a TCP IP network Dynamic IP address is typically assigned by
85. t as 8 8images will be stored in the FTP directory and FIFO first come first out based image will be saved in the FTP server Overwrite This is to refresh old image with new image in the ftp server This is normally used when the ftped image should be refreshed every time FTP Periodic Service Configuration Service O Enable Disable Server Address Ir O OS Base Directory Name Base File Name Po User ID Password Sequence Modula E Overwrite weekday L Month F Day F Hour F Minute SEC Sequence Video Channel F a DD D i 4 2 FTP service configuration If you get good understanding of Pre post alarm buffering and FTP directory option now you can easily configure FTP function of the system Please make sure that you have your own FTP server and create Based directory in the FTP server 4 2 1 Buffered FTP service Buffered FTP means that rising or falling edge based ftp will be done when there is any event and only pre post alarm buffered image can be sent to FTP server 92 Seyeon Tech Co Ltd Network Video Server User s Manual 1 Go to Advance Service menu in the service configuration mode and select Buffering Service option 2 Set up Pre alarm buffering configuration for FTP service 3 Set up FTP directory and file name option 4 Select the camera and set up FTP condition for each camera Up to 3 different ftp condition can be set up for each camera 4 2 2 Periodic FTP service Periodi
86. the server to be connected to broadband network or PSTN line In addition to basic network application port such as HTTP NVCP Voice port configuration and IP filtering options are provided 1 Network configuration You can change IP address of server through LAN configuration mode Network Configuration Static IP Static IP DHCP Client IP Address 211 255 356 142 Netwask 255 255 255 128 Gateway 211 255 36 254 DNS 1 168 126 63 1 DNS 2 168 126 63 2 Back Apply Reset 1 1 Static IP Select this to assign static IP in the server Subnet mask Default Gateway information must comply with the network where server is installed Otherwise server cannot be connected through network 1 2 DHCP Client This setting is recommended when the server is installed under DHCP environment in the LAN or Cable modem xDSL Modem which provides PPPOA type service We recommend you to use DHCP option when the server is directly connected to Cable modem only 1 2 1 How to access the server under DHCP environment Once DHCP is enabled there is no way for the user to know which IP is assigned to the server from the server web page Following is guide how to get to Know IP address of the server 50 Seyeon Tech Co Ltd Network Video Server User s Manual Network Configuration DHCP Client Static IP DHCP Client DNS 1 168 126 63 1 DNS 2 168 126 63 2 Back Apply Reset Once DHCP is enabled t
87. then click Reboot button 5 After rebooting Go to Admin Menu gt gt System Configuration gt gt Serial Ports Configuration 6 Click Serial Input Mode then following window will show up Serial Input Mode Configuration Current Port None Current Protocol HG 2322 Serial Input Model 7 Select the installed Serial Input Device Model on the dropdown menu as above 8 Click Apply button Note Serial Input device protocol can separately be uploaded into the system per customer needs User can upload serial input device protocol file which is provided by manufacturer eeo a 66 Seyeon Tech Co Ltd Network Video Server User s Manual only This function is not for general use Thus if you need more close information about this please contact your local distributor or manufacturer for further information sales flexwatch com 2 3 Serial output device The system supports to relay third party command to target device through Serial output device control mode Through this user defined message can be reached to target device The system supports two different modes One is X10 protocol for PLC Power Line Communication and UART Universal Asynchronous Receiver Transmitter device 2 3 1 Serial Output Configuration Following is guide for hardware cabling and setting 1 Connect your Serial Output Device to RS422 485 Port or RS232 COM or AUX port 2 Go to Admin Menu gt gt System Configu
88. ther information Ssales flexwatch com 2 3 3 UART Universal Asynchronous Receiver Transmitter device By pass command mode is supported by the system so that user can send command string to target device through the server from the remote area By pass command string can be sent either by third party application program or control panel inside of the system sss eee 68 Seyeon Tech Co Ltd Network Video Server User s Manual A By pass command string from third party This is to send command string from third party application program to the target device connected to the server More about this function can be supplied by HTTP CGI API guide B Control panel inside of the system You can create control panel of external device inside of the server and control target device through server web page This function is not for general use Thus if you need more information about this please contact your local distributor or manufacturer for further information sales flexwatch com 2 4 PTZ device connection and configuration PTZ Pan Tilt Zoom device connected to the server can be controlled through either Standard web browser or specific application program over IP network 2 4 1 PTZ connection When you install a RS 485 422 interfaced PTZ model PTZ device has to be connected to RS422 485 Port with RJ 45 connector And it can be configured either in AUX or COM part As mentioned above please check whether AUX or COM port fo
89. tion program 4 1 Alarm output device connection Any Relay contact type of output device can be interfaced with FlexWATCH server Simple connect the Alarm output device to Relay output DO port of FlexWATCH server Following is a circuit diagram for alarm output terminal Relay Output Circuit Diagram BUZZER BATTERY PlexwWATCH Alarm Circuit 4 2 Manual control of Alarm output device Alarm output device can manually be controlled through simple viewer page or admin page 4 2 1 Alarm output device through web browser Alarm output device control panel can separately run in the simple viewer page if control authority for Alarm output device is given to user If not allow alarm output device control panel will not be loaded in the simple viewer page 1 Go to simple viewer web page 2 Click Output control button in the web page ue eaa 75 Seyeon Tech Co Ltd Network Video Server User s Manual 3 Check the output port number and click apply button to activate the alarm output device 2 Output Contro E fol Output Control p art Name se 1 Do Name 0 C 2 DoNamei 3 A Co Namea DoName 3 Apply a Internet 4 2 2 Alarm output device through Admin Page Alarm output device can manually be controlled through Admin page of the system This option is recommended when web browser based alarm output control panel is hided and administrator want to manually control Alarm output device
90. tivate Alarm output device 77 Seyeon Tech Co Ltd Network Video Server User s Manual Advanced Service configuration Advanced service configuration is intended to provide more sophisticated functions which are required by sophisticated users Thus if you are not familiar with or not good at advanced features we recommend you to read this guide carefully and consult with your local vendor to get more close information about these features Advanced service can be categorized into Buffering service and None buffering service depending on whether server stores pre post alarm video in the system memory Buffering service means that the server can store pre post alarm image in the system memory and send stored image through FTP or e mail or allow user to view stored image inside of memory With this feature user can get pre post alarm image through e mail or FTP without missing any video before and after the event or playback stored Alarm buffered image by connecting the server None buffering service means that Advance service will be done without image buffering inside of the memory FTP Periodic Sensor notification service and Alarm output device control can be provided as a none buffering service option 1 Buffering Service Following services can be done by image buffering services e mail Up to 10 frame of Pre post alarm image can be sent when there is event is occurred FTP Rising or Falling edge Up to 256 frames of
91. u can view live view through standard web browser such as MS Internet Explorer or Netscape Navigator There are two different type of viewing option provided by FlexWATCH server One is simple live view and the other is FW Voyager which provides personal Network DVR Digital Video Recording and viewing solution Depending on the OS and web browser you can get different viewing option as well Following is guide for OS and Web browser for live view Operation System Simple view Activex MS Window Internet explorer only Java Applet mode Window Linux Unix MAC OS2 Netscape and other web browser FW Voyager Recording MS Window Internet Explorer only Note that FlexWATCH server supports only Internet Explorer or Netscape Navigator No additional support will be given to support any specific web browser except above 1 Live View Video server is designed to automatically sense the OS of Client PC and Web browser Depending on the OS and web browser it provides different option such as ActiveX and Java Applet 1 1 ActiveX based simple view This mode is to view live through I nternet explorer on the MS Window Small ActiveX components should be automatically installed or manually installed in the client PC to view live if Client PC use Internet explorer on the MS Window When the client pc is connected to internet ActiveX components will automatically downloaded and installed in the view PC if you accept to down
92. ulti images Clear buffer If pre defined buffer space is full this service will be stopped until the buffer is flushed out Please click below link to configure the service condition s Condition 1 Not Used sa Condition 2 Not Used s Condition 3 Not Used Preview Single I mages This is to view image one by one Preview Multi images You can view panoramic images of all the saved images at a glance 2 Click Preview Single Imager or Preview Multi images option to playback 3 Click Clear Buffer to delete all archived images amp Note Note that if you cleared the buffered image and want to save new images in the memory you need to go to Initial page of Advance Service configuration menu and click Stop amp Apply button to refresh the buffer images ZE Application Idea If you would like to download buffered images and save them in Client PC please contact your vendor or manufacturer to get in depth technical documentation 6 Sensor Notification service Sensor Notification service is to send alarm trigger information to third party application SSS eee 96 Seyeon Tech Co Ltd Network Video Server User s Manual program through CGI Patch This option is to invoke third party application program upon receipt of sensor information from FlexWATCH server 1 Go to Advance service configuration of Service configuration mode 2 Click None buffering service mode and go to sensor notification servi
93. up in the system any service which will be triggered by schedule condition will be not done correctly Also Server Date amp time info will be displayed on the image If you need to display correct time please set up more accurate time information 2 1 Date amp Time in the server clock Date amp time can be set up in the real time clock built in the server Simple set up Date amp Time info in the Date amp Time configuration field 42 Seyeon Tech Co Ltd Network Video Server User s Manual 1 Go to Date amp Time setup menu in the System configuration section of Admin mode 2 Set the correct time and click Apply button 2 2 Date amp Time using NTP server If multiple servers are installed over the network and controlled by client program and synchronized time info is required use NTP Network Time Protocol option 1 Go to NTP setup menu in the Network configuration section of Admin Mode 2 Type in NTP server name or use default NTP timeserver ntp ewha net if you do not know any NTP timeserver available in your area r Note NTP timeserver provides exact time wherever it is located 3 Enable the service and select Time Zone where the FlexWATCH server is located not user s viewing pc area 4 Type in NTP timeserver info 3 Admin Password Setup System administration Menu is user definable It is highly recommended to change default Admin Password to prevent any unwanted server control b
94. work Video Server User s Manual eg 103 Seyeon Tech Co Ltd Network Video Server User s Manual Warranty Product Network Video Server FlexWATCH 3440 Pe 1 year 82 2 3017 0866 www flexwatch com Seyeon Tech Co Ltd TEL 82 2 3017 0855 FAX 82 2 3017 0843 http www seyeon co kr http www flexwatch com A S Center Tel 82 2 3017 0855 Fax 82 2 3017 0843 Ree 104 Seyeon Tech Co Ltd
95. y any other person L Please note followings A Factory default admin ID is root and Password is root Case sensitive B Admin I D root is not user definable and unchanging A Only Admin Password is user definable 4 Access Control and User registration Access permission is to set up user account for the system access Through this configuration you can create multiple user account with different control authority for each camera and edit or delete user account Following features are provided by this mode sss eee 43 Seyeon Tech Co Ltd Network Video Server User s Manual A Option to allow system access without system Login ID amp PW Channel based different user account creation C Different control authority for Video PTZ Audio and relay output device control 4 1 Full Access To allow system access by anyone who know the IP address PTZ Audio and Relay output device can be controlled by anyone Thus if security for video is important it is highly recommended to user limited access mode below 4 2 Limited Access and User registration This is to limit server access to the authorized user only Through this mode you can create multi level access account for each camera not system level with different control authority Once Limited Access option is selected User registration should be followed to effectively use Limited Access function L Application Tips If servers are accessed and controlle

User's Guide - Security Point

Contents

Download Pdf Manuals

Related Search

Related Contents