Operating Instructions Tumble dryer
Contents
1. and remove it Support the door at the same time 4 Remove both door pins top and bottom Fit them on the other side of the machine Refit the hinge 5 Loosen the screws 13 in total on the inside of the door 6 Loosen the inner part of the door pull down and lift out 7 Switch the catch magnetic lock and the cover plate First loosen the screw holding the catch magnetic lock in place Then use a flat bladed screwdriver to remove the cover plate Refit the catch magnetic lock and the cover plate on the other side 26 8 Reattach the inner part of the door with the screws 13 in total 9 Move the plastic plugs on the upper and lower edges of the door Use a flat bladed screwdriver to remove the plugs 10 Loosen the two screws holding the handle in place on the door Push out the two plastic plugs inside the screw holes on the other side of the door Use the two screws to attach the handle to the other side of the door and press the plastic plugs into the holes where the handle was previously fitted 11 Refit the door by loosening the hinge screws slightly affixing the door and closing it Retighten the hinges Replace the plinth Quick guide Fabrics e Dry fabrics of the same type together to ensure that they dry as evenly as possible Turn on the main power switch Select a programme and any options e Turn the programme selector to the requir2. operating instructions and keep them in a safe place e Electrical installation if required should be carried out by a qualified electrician e The machine should only be used for tumble drying as described in these instructions e Repairs and maintenance relating to safety or performance must be carried out by a qualified professional e Damaged mains cables must only be replaced by a qualified electrician e Sufficient ventilation is required to prevent smoke from open fires or fumes from equipment burning other fuels being sucked into the room when the tumble dryer is running e Do not dry dirty laundry in the tumble dryer e Items that are stained with e g cooking oil acetone alcohol petrol kerosene stain remover turpentine wax and wax remover should be washed in hot water with extra detergent before they go in the tumbler dryer e tems such as foam rubber latex plastic waterproof textiles rubber coated items and clothes and foam rubber filled cushions must not be dried in the tumbler dryer e Fabric softener or similar products should be used as per the recommendations of the detergent manufacturer e he machine is not designed to be used by persons even children that are physically or mentally handicapped or lack experience and knowledge Such persons must receive instruction in how to use the machine from the person responsible for their safety e Children must be watched to ensure they do not play with
3. the machine AN Safety e The machine must not be used for drying items that have been dry cleaned at home or fabrics that may contain residues of flammable liquids A float shuts off the machine in the event of a blockage in the condensed water hose or if there is a risk of the condensed water container overflowing WARNING A When the tumble dryer is operating the back of the tumble dryer will get very hot Leave the machine to cool completely before touching the back Installation See the section Installation WARNING A Do not start the machine until it has been in position for 24 hours If for some reason the tumble dryer needs to be laid down for transport or service it must be laid on its left side viewed from the front Transport Winter storage If you need to move your machine or store it over the winter in unheated premises make sure that you drain the condensed water container beforehand Packing material Please sort waste materials in accordance with local guidelines Recycling This machine is manufactured and labelled for recycling In order to prevent personal injury the machine must be made inoperable after deciding to take it out of service Contact your local authority for information about where and how your machine should be correctly recycled Child safety General WARNING A Do not allow children to play with the tumble dryer e f the door is opened when a programme is runni
4. 0 00000001 4 Pull out the filter by grasping the handle in the middle 5 Wipe the net filter A Brush the lint from the filter with your hand Use a soft dry cloth to remove any deposits Care and cleaning 6 Remove the foam filter B found behind the net filter Wash the foam filter in a washing machine using a rinse or quick wash programme No detergent or hot wash is necessary The lint is washed away and the filter is not damaged 7 Clean the evaporator C by spraying water on the ribs with a plant spray bottle The lint runs off together with the water which is then evacuated by the condensed water pump 8 Replace both filters and close the evaporator door NOTE Avoid touching the ribs on the evaporator They are very thin and easily damaged If the ribs are bent or damaged the efficiency of the condenser is greatly impaired as is the drying result Cleaning the auto filter Clean the filter at the intervals shown on the machine s display or more often 1 Pull the condensed water container out and UP 2 Unscrew and remove the auto filter 3 Rinse the auto filter clean with water 4 Screw the autofilter back into place Check that the seal is properly seated Cleaning the outside of the machine Clean the outside of the machine and the programme panel with a mild cleaner Do not use solvents as
5. 4 14 14 14 14 14 15 15 16 16 17 17 Troubleshooting The machine will not start The machine loses all power during a programme The machine leaks water Drying takes too long Error messages Technical information Technical data Standard tests Information on energy labelling Service Before contacting the service division Installation Positioning the tumble dryer Adjusting the feet Condensed water Electrical installation Door hanging Follow these instructions Quick guide 18 18 18 18 18 18 19 19 19 20 21 21 21 22 22 23 23 23 25 26 21 Before using your machine for the first time Language selection You will be prompted to select the display language when you have connected your machine and start it for the first time Do as follows 1 Turn the programme selector to choose from US English English Svenska Dansk Norsk Suomi Fran ais Deutsch ltaliano Espanol PyccHMM Nederlands 2 Press Stop to save the setting Laundry labels Certain materials are not suitable for tumble drying Always check and follow the instructions on each item s laundry label You can find more information in the Advice and tips before you tumble dry chapter NOTE When starting the tumble dryer for the first time or after a long period without use you may notice a slight thumping noise This noise is completely normal and will disappear after a few loads Safety instructions Read the
6. alf load T Auto normal dry with full load Auto normal dry with half load Airborne acoustical sound Type of dryer A Automatic NA Non Automatic Standby mode duration Condensation efficiency class IMESA ES7PEHP 7 kg A 212 kWh year 1 77 kWh 0 94 kWh 91 96 91 91 Auto normal dry 131 minutes 174 minutes 99 minutes 66 dB A A 2 minutes AS 1 Based on 160 standard drying cycles for Auto normal dry full and half load and consumption in accordance with the low power modes The actual energy consumption will depend on how the machine is used 2 Auto normal dry used with a full or half load is the standard programme to which the information on the label and the information sheet refer This programme is intended for drying normally wet cotton laundry and in terms of energy consumption is the most effective programme for cotton 3 On a scale from G least efficient to A most efficient 20 Service Before contacting the service division See the Troubleshooting and Care and cleaning chapters to see whether you can rectify the problem If you need to contact the service division make sure that you know the model designation type designation and serial number The model designation 1 can be found on the first page of the operating instructions and on the machine panel The type designation 2 and serial number 3 can be found on the type plate which is found on the
7. and cleaning chapter Call the service division if Thermistor fault appears on the display Press the Stop button to close any error messages Technical information Technical data Height 850 mm Width 595 mm Depth 585 mm Weight net 52 kg Cylinder volume 1121 Max drying capacity 7 Kg Speed 50 55 rpm Rated povver See type plate Drum material Stainless steel Outer casing material Powder coated and hot galvanized sheet steel or stainless steel Setup Stacking or freestanding Standard tests For the standard test the machine s condensed water hose must be connected to a drain Europe Drying performance EEN 611 21 392 2012 Auto normal dry 7 kg cotton Energy declaration EN 611 21 392 2012 Auto normal dry 7 kg cotton Test method for noise IEC 60 704 2 6 measurement Technical information Information on energy labelling Information sheet in compliance with Commission Delegated Regulation EU No 392 2012 Imesa Model designation Max drying capacity Energy efficiency class Annual energy consumption AE Energy consumption Auto normal dry with full load E ary Auto normal dry with half load E m Power consumption Off mode P Left on mode P Condensation efficiency Auto normal dry with full and half load C Auto normal dry with full load C Auto normal dry with half load C Drying programme Programme time minutes Auto normal dry with full and h
8. e text Done appears on the display when the programme is finished The compressor s cooling fan continues to run after the programme finishes but stops automatically or when any button knob is activated 6 Backlighting Two minutes after the drying programme finishes the backlighting on the display and option buttons enters energy saving mode Condensed water The condensed water container must be emptied after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes full to overflowing the programme is interrupted and Over Flow appears on the display Empty the container and press the Start button to start a new programme TIP The condensed water is decalcified and can be used in steam irons Pour it through a coffee filter Automatic emptying For connection to a separate drain see the installation instructions in the set of documents NOTE e Clean the lint filter after each load e Drain the tank after each load WARNING A If the lint filter becomes clogged the machine s automatic overheating cut out may be triggered Clean the filter wait until the machine has cooled then try starting it If it still does not start Call the service division Once drying has finished Turn off the main power switch Remove the clothes and close the door to prevent small children from climbing into the machine Settings You can carry o
9. ed programme Load the garments e Close the door o 6 7 Press the Start button Drying programme finished e Done appears on the display vvhen the programme is finished e Clean the lint filter after each load Once drying has finished e Turn off the mains power switch and close the door LLUIS La MIX Ges MHIL ATLL Art No 8094267 Rev 02 We reserve the right to make changes FSC pone sees C TD70 C SPK HP www fsc org FSC C1 14278 502843 en 10 13
10. ed to the bottom left corner of the back of the machine 22 How to assemble the stack 1 Remove the two tip guards from the back of the tumble dryer Replace the screws that held the tip guards in place SL Z 2 Undo the two screws indicated on the back of the washing machine 3 Secure the anti tilt device using the screws as shown in the picture 4 Attach the plastic cups for fixing the tumble dryers front feet to the washing machine s top cover This is essential as only when the tumble dryers feet are resting in the plastic cups can you be sure that the tumble dryer is correctly positioned on the washing machine Break off tag A on the cup fitted on the right hand side and tag B on the cup fitted on the Installation left hand side Then remove the paper from the self adhesive surface under the plastic cups Pl A 5 Fit the plastic cups so that the tags marked with arrows are against the front edge or side edge of the cover and press them firmly onto the cover Then break off the remaining tags E 6 Push out the knock out hole on the back of the tumble dryer you must not remove it just open it using a hammer and screwdriver 7 Push the tumble dryer in under the metal brackets At the same time keep the front edge raised by 10 mm to 20 mm 8 Lower the tumble dryer s front feet into the plastic cups and adjust the tumble dryer to ensure it is level V Ad
11. front of the tumble dryer inside the outer door 0 0 0 0 0 OOOSODCOOOOOO OOOOOOOOOO OOCOCO TYPE 21 Installation WARNING A Do not start the machine until it has been in position for 24 hours If for some reason the tumble dryer needs to be laid down for transport or service it must be laid on its left side viewed from the front Positioning the tumble dryer The tumble dryer can be free standing or in a stack Remember that the tumble dryer produces heat and should therefore not be located in a room that is too small If the room is very small drying will take longer due to the limited quantity of air WARNING A e Any electrical installation must be carried out by qualified professionals e The machine must not be installed behind a lockable door a sliding door or a door with hinges on the opposite side to those of the tumble dryer e The tumble dryer s plinth ventilation must not be blocked by a rug or the like NOTE To improve ventilation leave the door to the room where the tumble dryer is located open Freestanding The tumble dryer can be positioned beside the washing machine An air gap of at least 5 mm must be left between the washing machine and the tumble dryer Stacking The tumble dryer can be placed on top of a IMESA washing machine Use the two foot cups found in the document bag included with the machine and the two tip guards attach
12. justing the feet Screw the feet in or out so that the tumble dryer is both stable and level Condensed vvater The machine is supplied as shown in Option 1 inset This means that the condensed water is pumped into the condensed water container which must be removed and emptied by hand Option 2 allows you to remove the small short hose from the nipple Attach the rubber hose supplied to the same nipple The water can then be pumped out into a sink or a floor drain 2a Max 1000 mm Electrical installation If the machine is delivered from the factory with a plug attached it can be connected to an earthed wall socket Otherwise a permanent connection using a multipolar circuit breaker must be made by a qualified professional 23 Installation Connection on delivery e 230V 1 Phase 10A e 50Hz e Use a type A residual current device 24 Door hanging o oo o o 06020 00000 696969 0000990969909 o 00 0009950959 00 6000099509 o 0 o9 060 080 o 009990 O 020090 H 0920 oo 4 Locking hook 1 Hinge pins top and bottom 2 Cover plate 5 Hinges left right side 6 Plinth 3 Plastic plugs on the upper and lower edges 25 Door hanging You can choose whether the door is hung on the right or the left Follow these instructions 1 Remove the plinth 2 Remove the hinge two screws 3 Lift the door up
13. lter The lint filter must be cleaned after each load 1 Grasp the filter holder handle and pull it towards you to open the lint filter 2 Open the lint filter Use your thumb to press on the edge as illustrated and pull it out 3 Use your hand or a soft cloth to remove the lint from all sides of the filter If necessary use a damp sponge and a small amount of washing up liquid to remove any deposits Dry the filter thoroughly with a towel 4 Close the lint filter before closing the door Care and cleaning Emptying the condensed water container If you have not connected the machine to a separate drain the condensed water container must be emptied after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes full to overflowing the programme is interrupted and Over Flow appears on the display Empty the container and press the Start button to restart the programme For connection to a separate drain see the installation instructions in the set of documents Cleaning the evaporator filter and evaporator Clean the evaporator and the evaporator filter at the intervals shown on the machine s display or more often 1 Turn off the Main power switch and open the outer door 16 2 Remove the plinth 3 Open the evaporator door J 2 gt U00
14. mption values given below the requirements are as follows Temperature of intake air 23 C Moisture content of intake air 55 96 Drying temperature Normal Program Load Spin speed rpm Energy consumption Programme time approx kWh approx min 1 1 Auto extra dry Cotton linen Auto dry Cotton linen Crease resistant polyester cot ton LI ECS H9 00 0 ECS EE ECS 6 S ES 0 94 Cotton linen Crease resistant polyester cot ton Auto Iron dry Cotton linen Test program according to EN61121 2012 The option Time save shall be active 5 1 0 1 9 1 1 1 1 9 1 7 1 6 Auto normal dry Cotton linen 1 1 1 5 1 3 1 1 1 7 1 5 1 2 12 Tumble drying 5 Press the Start button Remaining drying time An estimate of the remaining drying time will be shown on the display a few minutes after the drying programme starts For example 1 35 means that it will take approximately 1 hour and 35 minutes for the load to dry The actual remaining time may be longer than the estimated time shown on the display The remaining time is then shown as 0 15 until the load is sufficiently dry You can stop the tumble dryer by pressing the Stop button or by opening the door In both cases the programme is stopped and starts from the beginning if restarted NOTE The programme will not be affected if you change the programme selector after the programme has started Drying programme finished Th
15. ng the garments may be very hot with a risk of burn injuries e The tumble dryer does not start automatically when the door is closed if a child pulls the door shut from the inside for example Child safe start By activating the child safe start function you can prevent children from starting the tumble dryer or changing the current programme Activating deactivating Child safe start Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stop button and switch on the machine with the main power switch Then press the Stop button 5 times within 10 seconds 3 Select the setting you want to change by turning the programme selector 4 Press the Stop button once 5 Change and save the setting as described below 6 Press the Start button to return to the programme menu You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe On or Child safe Off 2 Press the Stop button once to save the setting You can temporarily deactivate Child safe start by pressing the Start and Stop buttons at the same time Child safe start will be deactivated for 3 minutes Description of the tumble dryer OOOOOOOOOO OOOOO 1 Main power switch 5 Lint filter 2 Condensed water container 6 Outer door 3 Panel 7 Evaporator and filter 4 Type plate Advice and tip
16. ramme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto normal dry Temperature normal These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto extra dry Below temperature Energy Save This programme is for items that are particularly difficult to dry such as jeans with very thick seams Auto dry Bow temperature Energy Save These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto normal dry Bow temperature Energy Save These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto Iron dry This programme shuts off the heat once the load is just damp enough for ironing or pressing Tumble drying Programme chart Here we present the energy and time consumption of a few different programmes The table shows the effect of using different spin speeds when washing the load Consumption can vary depending on room temperature humidity load variations in the power supply and selected options For the consu
17. s before you tumble dry Here are some tips that may help you before you begin tumble drying Have the clothes been spun ltems to be tumble dried should be spun at 1000 rpm or faster Higher spin speeds save energy and reduce drying time Materials that can be tumble dried This symbol means that the material is suitable for tumble drying Fabrics best suited to tumble drying are cotton fabrics terry cloth and synthetic fibres Garments will be softer and lighter when tumbled than when hung out to dry NOTE The tumble dryer does not cause any significant wear on fabrics The lint that collects in the lint filter consists of dust and fibre residues formed when the items are used Materials that must not be tumble dried esa This symbol means that the material is not suitable for tumble drying Certain materials may melt or become a fire hazard if exposed to heat and others can lose their shape or shrink And do not tumble dry e materials labelled Do not dry near heat e garments that have been dry cleaned at home e plastic foam e fibreglass material e wool must not be tumble dried because of the risk of felting Static electricity To reduce the risk of static electricity in the laundry after tumble drying you can e Use fabric softener when washing e Wait five minutes after the drying program ends before opening the door and removing the laundry from the dryer NOTE You can stop the tumble dryer b
18. these can damage the machine Do not hose down or spray the machine with water NOTE Do not allow dust to accumulate around the machine Keep the area around the tumble dryer clean and cool dust heat and moisture prolong drying times Troubleshooting The machine will not start Check that the door is properly closed that the main power switch is on that the plug is connected that the main fuses have not blown The machine loses all power during a programme Contact the service division The machine leaks water Check that the autofilter and its seal are installed correctly and not faulty Drying takes too long 18 Check that the lint filter is not blocked See the Care and cleaning chapter Empty the condensed water container Clean the evaporator filter net filter foam filter evaporator lint filter and autofilter see chapter Care and cleaning Error messages If Over Flow appears on the display the condensed water container is full or the evaporator filter is blocked Empty the container clean the filter and restart the machine See the Care and cleaning chapter Read Drying takes too long in this chapter if Max program time appears on the display If Clean Lint Filter appears on the display clean the lint filter lf Clean condenser appears on the display clean the evaporator See the Care and cleaning chapter If Clean auto filter appears on the display clean the auto filter See the Care
19. tty Operating Instructions Tumble dryer IMESA ES7PEHP Operating Instructions Tumble dryer IMESA ES7PEHP Dear IMESA customer Welcome to the family of IMESA customers We hope that you will have many years of use from your new machine The machine has many features To make the most of its functions we recommend that you read the operating instructions before using the machine The operating instructions include information on how you can help protect the environment Contents Before using your machine for the first time Language selection Safety instructions Safety Transport Winter storage Packing material Recycling Child safety General Activating deactivating Child safe start Description of the tumble dryer Advice and tips before you tumble dry Materials that can be tumble dried Materials that must not be tumble dried Static electricity Tumble drying Sort your fabrics Press the main power switch until the display lights Open the door load the items and then close the door Select the programme Press the Start button Drying programme finished Settings You can carry out the following settings How to choose the settings Audible Volume Language Child safe Care and cleaning Cleaning the lint filter Emptying the condensed vvater container Cleaning the evaporator filter and evaporator Cleaning the auto filter Cleaning the outside of the machine 10 10 11 13 13 1
20. ut the follovving settings e Language e Child safe e Audible Volume How to choose the settings Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stop button and switch on the machine with the main power switch Then press the Stop button 5 times within 10 seconds Select the setting you want to change by turning the programme selector Press the Stop button once Change and save the setting as described below Press the Start button to return to the programme menu Audible Volume 1 Turn the programme selector and choose Buzzer On or Buzzer Off to set whether the tumble dryer should audibly indicate that the programme is finished or that an error has occurred 2 Press the Stop button once to save the setting O C C Language 1 Turn the programme selector to choose from US English English Svenska Dansk Norsk Suomi Francais Deutsch Italiano Espanol Pyccknh Nederlands 2 Press the Stop button once to save the setting Child safe You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe On or Child safe Off 2 Press the Stop button once to save the setting You can temporarily deactivate Child safe start by pressing the Start and Stop buttons at the same time Child safe start will be deactivated for 3 minutes 14 Care and cleaning Cleaning the lint fi
21. y pressing the Stop button for three seconds or by opening the door In both cases the programme is stopped and starts from the beginning if restarted If you do not want to restart the programme then immediately remove all laundry and spread it out to allow the heat to dissipate Tumble drying Below are step by step instructions to help you achieve the best possible tumble drying results You will achieve the most uniform drying results if the items are made of the same type of material Do up zips and buttons fasten belts sort the items and adjust the load and temperature 2 1 Sort your fabrics Press the main power switch until the display lights Open the door load the items and then close the door 3 10 Tumble drying 4 Select the programme Programme selector Programme name Start Stop Select a programme by turning the programme selector The selected programme is shown in the display window Guidelines as to what specific programmes can be used for The Auto extra dry Auto dry and Auto normal dry programmes have two temperature settings Normal temperature but also low temperature for more delicate items Auto extra dry Temperature normal This programme is for items that are particularly difficult to dry such as jeans with very thick seams Auto dry Temperature normal These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry prog
Download Pdf Manuals
Related Search