Operating Instructions ZC-AF16 (PAL, high-resolution)
Contents
1. LI 9 10 ZC AF 16 2 Control names and Functions 1 Tripod adaptor This adaptor can also be attached on the bottom of the camera 2 Lens mount cap 3 When push the TELE Key picture is telephoto 4 When push the WIDE Key picture is wide angle 5 FOCUS NEAR Key In a manual situation focus get near 6 FOCUS FAR Key In a manual situation focus get far 7 MENU Key If you want to set up a diverse function you can push this button 8 Video output S Video type Connect to the S Video in connector of a monitor 9 Interface of camera control JACK 6Pin Din Jack Type e Connect to an external voltage controller e You can supply a camera with power from this DC12V 10 Video output BNC type Connect to the video in connector of a monitor POWER IN CONTROL side of the camera You can adjust focus and zoom by a pin terminal on the back PIN NO Description Color 1 RXD RS232 Green 2 TXD RS232 White 3 External Key input A D IN Brown Blue 4 NC Yelllow 5 GND Black 6 Power input DC 12V Red is the color of the cable ADIN 6 8K 8 2K 12K 18K 68K 180K Hm I re A a Power O MENU DIGITAL 709 CF onor owore TELE _f WIDE NEAR FAR Fam ef it I ji ji Jr Auto MENU 1 INITIAL SET ON BACKLIGHT OFF COLOR ON NEGATIVE OFF FOCUS PUSH AUTO FLICK2. Operating Instructions ZC AF 16 PAL high resolution Before installing and using the camera please read these instructions thoroughly and retain them for later reference E Bal RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Warning To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only Regulatory Notices For U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica
3. e High magnitude of zoom lens with optical X 16 Digital X128 e Auto Focus e Auto White balance e Auto exposure with DC Iris control e On Screen display Cautions for Safe Operation Power Supply Where it is exposed to rain This camera must always be operated a 12V Where it is subject to strong vibration DC power supply Close to generators of powerful electromagnetic radiation such as radio or TV transmitters Handling of the unit Be careful not to spill water or other liquids on Care of the unit the unit or to get combustible or metallic Remove dust or dirt on the surface of the material inside the body If used with foreign lens with a blower matter inside the camera is liable to fail or to Use a dry soft cloth to clean the body If it is be a cause of fire or electric shock very dirty use a cloth dampened with a small quantity of neutral detergent then Operating and storage location wipe dry Avoid viewing a very bright object such as light Avoid the use of volatile solvents such as fittings for an extended period Avoid operating thinners alcohol benzene and insecticides or storing the unit in the following locations They may damage the surface finish and or impair the operation of the camera Extremely hot or cold places operating temperature 10 C 50 C however we recommend that the unit be used within a temperature range of 0 C 45 C Damp or dust place Noo Operating Controls and Their Functions
4. of Lens s Iris IRIS of lens is fixed manually and the action of exposure compensation depend on its of AGC AE MODE AE MODE IRIS ADJUST IRIS ADJUST 10 gt IRIS ADJUST Set the AE mode to IRIS using Adjust the IRIS ADJUST to a The whole MENU is displayed using F or F key code The IRIS desired value TELE or WIDE key code Moving ADJUST menu is appeared another item of MENU is available e AGC The change of AGC is available 00 255 AGC of camera is fixed manually and the action of exposure compensation depend on its of IRIS of LENS AE MODE AE MODE AGC AGC ADJUST AGC ADJUST 10 AGCADIUST 10 Set the AE mode to AGC using Adjust the AGC ADJUST toa The whole MENU is displayed using F or F key code The AGC desired value TELE or WIDE key code Moving ADJUST menu is appeared another item of MENU is available e MANUAL Use to set the shutter speed IRIS and AGC manually AE MODE MANUAL AE MODE MANUAL SHUTTER NORMAL SHUTTER NORMAL SHUTTER NORMAL IRIS ADJUST 0 IRIS ADJUST 0 IRIS ADJUST 10 AGC ADJUST 60 AGC ADJUST 60 Set the AE mode is MANUAL to a desired value mode using F or F key Adjust the SHUTTER code The SHUTTER IRIS or WIDE key code ADJUST AGC ADJUST MENU Moving another item of is appeared MENU is available The whole MENU is displayed using TELE a desired value Adjust the IRIS ADJUST to AE MODE MANUAL AE MODE MANUAL SHUTTER NORMAL SHUTTER NORMAL IRI
5. value by using desired value by using displayed using TELE or or F key code The F or F key code F or F key code WIDE key code Moving RED BLUE ADJUST menu another item of MENU is is appeared available Caution The values of RED ADJUST and BLUE ADJUST are not changed when the INITIAL SET is set to ON e INDOOR amp Use to set the preset WBC INDOOR Mode 3200 K WBC MODE INDOOR e OUTDOOR lt Use to set the preset WBC MODE OUTDOOR WBC OUTDOOR Mode 5100 K e MANUAL MWB Hue control adjustment is available manually Adjust MWB CONTROL to a desired value WBC MODE MANUAL WBC MODE MANUAL MWB CONTROL 0 MWBCONTROL 0 NIWBCONTROL 0 Set the WB mode is MANUAL mode Adjust the MWB CONTROL The whole MENU is displayed using using F or F key code The to a desired value TELE or WIDE key code Moving MWB CONTROL menu is appeared another item of MENU is available e PUSH AUTO PWB A regular environment or object was forced to do White Balance action And then the PWB mode turn off Manual WB mode It makes good use of Manual WB mode in the usual environment It can prevent unsuitable color reproduction or decolor on the act of White Balance WBC MODE PUSH AUTO WBC MODE PUSH PUSH AUTO OFF PUSH OFF gt push ON PUSH OFF Set the WB mode is MANUAL Adjust the PUSH AUTO Adjust the PUSH AUTO The whole MENU is mode using F or F key cod
6. ERLESS OFF WBC MODE AUTO Setting The Menu e The On Screen Display menu can be used by MENU TELE WIDE F NEAR F FAR Key Menu 1 1 INITIAL SET Set the initial mode ON the changed data are renewed 2 BACKLIGHT In case of the excessive light is behind the center object It is necessary to prevent the center object too darken Turn the BACKLIGHT ON then the center object became lighter 3 COLOR Use for changing color and monochrome of picture e ON Color mode e OFF Black and White mode MENU 1 INITIAL SET ON BACKLIGHT OFF COLOR ON NEGATIVE OFF FOCUS PUSH AUTO FLICKERLESS OFF WBC MODE AUTO 4 NEGATIVE Use for changing NEGATIVE and POSITIVE mode e ON NEGATIVE mode e OFF POSITIVE mode 5 FOCUS AUTO MAN Set the focus mode to Auto or Manual PUSH AUTO Set the focus mode to Push Auto mode 6 FLICKERLESS Set the FLICKER ON mode then the flicker is removed e In case of NTSC system Shutter Speed 1 100 sec e In case of PAL system Shutter Speed 1 120 sec 7 WBC MODE e AUTO WB Range 2800 K 8000 K e SPECIAL SWB Under the special WB condition Differ from curve of the control color temperature Adjust Red and Blue to perform a desired White Balance WBC MODE SPECIAL WBC MODE SPECIAL RED ADJUST 2 me RED ADJUST 10 RED ADJUST 0 BLUE ADJUST 253 BLUE ADJUST 10 BLUE ADJUST 0 Set the WB mode is Adjust the Red toa Adjust the Blue to a The whole MENU is SPECIAL mode using F desired
7. P NO 3834RS0071J CBC Deutschland GmbH Hansaallee 191 D 40549 Dusseldorf Phone 49 211 53 06 70 Fax 49 211 53 06 71 80 mail info cbc de com www cbc de com
8. S ADJUST 10 lt 9 iris ADJUST 10 AGC ADJUST 80 AGC ADJUST 80 AGC ADJUST 60 Adjust the AGCADJUST The whole MENU is to a desired value displayed using TELE or WIDE key code Moving another item of MENU is available The whole MENU is displayed using TELE or WIDE key code Moving another item of MENU is available On Screen Display Some of these functions will FUNCTION OSD Format Description be displayed every time the 1 Focus Mode Non displa Focus Auto Mode camera is operated and then F eniai disappeared after 5 seconds CSUS MANNA MEYS 2 Back Light Non display Back Light OFF j Back Light ON 1 2 3 46 3 Shutter Speed Non display Normal Shutter NTSC 1 60 PAL 1 50 1 125 8 variable steps 1 10 000 STAND BY 4 STAND BY Indicate the camera stand by during the camera s power turning on 5 CAMERA ID According to write the identification number to Tx12 125 each camera multi point control is available PC Control 000 255 On Screen Display FUNCTION OSD Format Description 6 WBC Mode Non display White Balance AUTO SWB Special Auto White Balance Adjustment Mode according to change of external illuminant RED ADJUST and BLUE ADJUST 0 255 are available After changing R B value the maintenance mode is AUTO WB Preset for INDOOR 3200 K Wb Preset for OUTDOOR 5100 K Manual WB Adjustment In manual mode the HUE contro
9. e mode ON WB act mode OFF WB act displayed using TELE The MWB CONTROL menu is automatically manually or WIDE key code appeared Moving another item of MENU is available MENU 2 CAMERA ID SHARPNESS BRIGHTNESS ZOOM START ZOOM END FOCUS FROM AE MODE OFF 10 42 x1 x128 1CM AUTO Menu 2 8 CAMERA ID To connect a large number of camera It can be assigned to identification number to each camera control easily OFF 1 255 total numbers of ID are 256 CAUTION To transfer ID code of camera set the ID number of camera in first And then the ID number display continuously 9 SHARPNESS Use to change the contour of scene 0 15 10 BRIGHTNESS Use to change the brightness of scene 0 99 11 ZOOM START x1 x15 Use to change the start magnification of zoom 0 99 12 ZOOM END x2 Use to change the end magnification of zoom Caution This value must be larger than the value of ZOOM START 13 FOCUS FROM 1CM 10M Use to change the object distance limit for focusing For example 1CM means that the camera is able to focus on the objects which are from a distance of 1cm to infinite 14 AE MODE In the situation is unadjustable exposure AE mode support to make a fit exposure e AUTO Use to compensate the exposure automatically e SHUTTER Use to change the Shutter Speed control In this time AE mode act automatically 8 steps control is available e IRIS Use to change the value
10. l is available 0 99 PWB Push Auto White Balance Turn this mode ON the white trace automatically Turn this mode OFF preserve the white of final auto tracing action Manual 7 ZOOM Display W E T x16 In case of 16X Zoom WwW IT T x32 In case of 32X Zoom Digital Zoom 2X WE IFT x64 In case of 64X Zoom Digital Zoom 4X Specifications Image device Sync system Horizontal resolution Lens Digital Zoom Minimum illumination S N Automatic control 1 4 interline transfer CCD NTSC High resolution 380 000 NTSC Normal resolution 250 000 PAL High resolution 440 000 PAL Normal resolution 290 000 Internal sync Approx 450 Line NTSC High resolution 320 Line NTSC Normal resolution 450 Line PAL High resolution 320 Line PAL Normal resolution at center of screen x16 Optical Zoom f 3 9 63mm F1 6 2 4 Auto IRIS Normal resolution x32 Zoom Digital Zoom x2 High resolution x128 Zoom Digital Zoom x8 1 Lux F1 6 More than 48dB AGC OFF Auto Exposure DC iris AGC Auto white balance Auto focus Zoom tracking Specifications Power requirement 12V DC Video output BNC type S Video type 1 0Vp p 750hms Power consumption Max 4 7w operating temperature 10 C 50 C Operating Humidity 0 80 Storage temperature 20 C to 60 C Dimensions 59 4mm W x 61 2mm H x 95mm D Specifications are subject to change without notice
11. tions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Contents FATES cerne caine eee cme sete dune ease E E E E aiasnetss 3 Cautions for Safe Operation roning an pig raa a a ernennen 4 Operating Controls and Their Functions ersuunssennsenssennnnnennnnnnnnnnnnennnnnnnnnnnnnnnnnennnnennnnnann 5 Power IN CONTROLwiniec isi cticissheisscctiecdbedctdebsucehagdenssdedecdetnedatie innen anhand nennen innen heiten 6 setting The Men s ariii aan 7 13 On Screen Display sie atti de ia ee tn ee aed eee ace ae a 14 15 Specifications siseses ear irin rE nE EA RE E MiA A EE a T EAE Eas EEES 16 17 FEATURES The power zoom color video camera is designed for use in monitoring system e High resolution and high sensitivity with a 1 4 inch CCD Charge Coupled Device
Download Pdf Manuals
Related Search