VNS-HC8510A series detailed operating instructions
Contents
1. f VNS HC8510A series detailed operating instructions Remote Controller key features additional information F1 F4 advanced user defined extensions design for specific users and machine general users will not need it Remote is a multi model fits all HOME shortcut key of preset position the user can customize a particular location DISP display software version number non customers use function key PRSET preset point setting key PATTERN set the parade path to preset point RUN Run PATTERN setted parade path and quit the cruise mode A shortcut key of preset position parade starting point B shortcut key of preset position parade ending point CAM shortcut key of camera selection mode SHOT into the preset point of call mode shortcut AUTO Automatic parade DELETE delete key of the preset point SPEED camera speed setting key ENTER confirm button and automatic cruise stop button P1 P8 shortcut of entering preset point 1 S4 shortcut of different cruise speed SETUP Baud rate and protocol settings button Setting Methods 1 Call preset points Press the SHOT button to enter Preset point call mode respectively enter the numbers 0 9 can be directly invoked 9 below preset point do not need to press ENTER button to confirm the camera will reach preset point position If want to enter 9 or more preset point please press key To delete the wrong please press C key and pres2. 001010 001011 001100 001101 001110 001111 010000 010001 010010 010011 010100 010101 010110 010111 011000 011001 011010 011011 011100 011101 011110 10 01 11 00 10 01 11 00 10 oO Oo O O O na O a O O gt a O O a a 00 00 00 10 10 10 10 01 01 O O O O O O DIP switch position camera switch position 1 6 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 3 4 9 fi NO 31 011111 111110 NO 32 100000 000001 4 Multi cameras Selection Control The first step set the camera address According to the method described above to definite of the camera number and set the corresponding address of the camera The second step select the camera Click CAM key to enter the ball machine selection mode respectively enter the numbers 0 9 can directly select the 9 below camera do not need to press ENTER button to confirm To set up nine or more numbered camera press key you can enter values greater than 9 to delete the wrong press C key to confirm press ENTER key then this number of camera choose successfully The third step is to use other keys to control on the camera s operations W Highlight 1 The maximum operating speed of the camera is of 63 2 APTZ controller is defaulted can control 32 cameras and most can control up to 1
3. 27 from No 33 to start somewhere need to use the software Write up to 32 preset points can be set can only be used to set the start and end location of the two cruise mode and between the and B it can not set other preset points To set more pre set points the method please accordance with Article 4 to set up 4 Remote control of other key features please refer to the original manual Appendix Operation Setting for AY HC8510A Series 1 Camera Address Setting A Press CAM Key then choose the Address of the Camera need to be setted B Press PRESET SETUP button 3 seconds separately 2 Baud Rate Setting A Press SETUP button 3 seconds into camera s set the baud rate and protocol mode use the up down key to select protocol or protocol B Press PRESET SETUP button 3 seconds separately 4 4
4. ill see the PCBA there is a 10 bit mode DIP switch which DIP 1 6 is the camera address DIP7 8 is the baud rate DIP7hit the ON DIP8hit the OFF baud rate is 1200bps DIP7hit the OFF DIP8hit the OFF baud rate is 2400bps DIP7hit the ON DIP8hit the ON baud rate is 4800bps DIP7hit the OFF DIP8hit the ON baud rate is 9600bps DIP 9 is the camera protocol the switch hit the ON is a Pelco P hit the OFF switch is Pelco D DIP 0 is a RS485 terminal resistance hit the ON switch is to connect a 1200 resistor 2 Camera Address Setting Camera addresses are set aside in the form of binary code on switch To simultaneously control more than one camera at the same time need to set up different address For example if you want to set on the 4th camera s address first decimal 4 must be converted into a binary that is 100 Then hit the DIP 3 switches ON while hit in the other switch among DIP 1 6 OFF 3 To simultaneous control several cameras the specific address settings please see the following comparison table in the following table use 1 to indicate when DIP switch position is ON and use 0 for OFF 2 4 Camera number decimal NO 1 NO 2 NO 3 NO 4 NO 5 NO 6 NO 7 NO 8 NO 9 NO 10 NO 11 NO 12 NO 13 NO 14 NO 15 NO 16 NO 17 NO 18 NO 19 NO 20 NO 21 NO 22 NO 23 NO 24 NO 25 NO 26 NO 27 NO 28 NO 29 NO 30 Camera address binary 000001 000010 000011 000100 000101 000110 000111 001000 001001
5. reset points the beginning of setting mode enter a number 1 2 3 2 1 respectively the camera will reach the preset point position that is to guide the camera to go a complete manual parade between 3 points and then press button PATTERN 3 seconds to complete the setup The fourth step press RUN button to start to run this parade pattern The camera will follow a ready pre set path to start parade and also will stay in the running the stay location is the all preset points To exit the cruise mode just press RUN button 5 To set the starting point to the end of the parade path Methods The first step set preset points Click PRSET button 3 seconds to enter preset point setting mode respectively enter the letters AB directly to set start and end point If you are running and found anti AB path then re set the AB can be exchanged AB location The second step press AUTO key to run the AB model camera repeatedly uniform parade between AB press 51 54 can change the speed of parade To stop the parade press ENTER button 6 To set the baud rate and protocol Methos Press SETUP button 3 seconds into camera s set the baud rate and protocol mode use the up down key to select P protocol or D protocol use the left right key to change the baud rate there are 1200 bps 2400 bps 4800 bps 9600 bps optional and then press ENTER button Camera Address Setting 1 DIP Switch Description Open the camera you w
6. s ENTER key the camera will arrive the preset point location 2 Remove existing preset points Press DELETE button for 3 seconds to enter delete mode preset points respectively enter a number 0 9 can directly delete the following nine preset points do not need to press ENTER button to confirm If you want to delete more than 9 preset points please press key then you can enter values greater than 9 To delete the wrong please press C key then press ENTER key the camera will delete this preset point 3 Set up a new preset points Press PRSET button for 3 seconds to enter preset point setting mode enter the numbers 0 9 respectively can be directly preset settings the 9 below point do not need to press ENTER button to confirm To set up more than 9 preset points press key you can enter values greater than 9 To elete the wrong plese press C key then press ENTER key to confirm when the preset point was successfully set 4 Set tour path of preset points The first step set preset points Example pre set point 1 point 2 and points 3 the location of these three preset points and camera lens positions are different that is non linear three positions The second step determine the parade path Such as a parade of the three point manner is 1 2 3 2 1 that is 1 4 N CCTV repeated among 123 parade The third step the memory parade path Press PATTERN button 3 seconds into the parade path of p
Download Pdf Manuals
Related Search