Operating Instructions (English)
Contents
1. Push turn Rivets Hang the elite Panaboard on the wall mounting plates with the screw heads Operating Instructions 49 Installation Manual 5 Remove the screws on each end of the bottom 7 Fasten to the wall of the lower frame cover e Use 4 screws to attach the fasteners on the e UB T880 2 screws bottom of the board securely to the wall UB T880W 4 screws UB T880 is shown in the following figure as an example Notice e Screws 4 count are not included with the elite Panaboard Please purchase screws with a size of M6 appropriate for your type of 6 Open the pen tray remove the screw caps and wall the screws and remove the lower frame cover Open the pen tray and remove the right and 8 Attach the lower frame cover left screw caps 2 locations Then remove the Perform step 6 and step 5 in reverse and attach screws and remove the lower frame cover the lower frame cover making sure there is no unevenness with the front surface Notice When removing the screw caps hold them Notice E with your finger to prevent them from flying e When mounting on a wall do not hit or jolt off the elite Panaboard After mounting gently apply some weight on the elite Panaboard to make sure that it is Screw Caps securely fastened to the wall 9 Confirm that the elite Panaboard can operate e See Confir2. 16 Operating Instructions Usage Notice e When the electronic pen and your finger are used simultaneously the elite Panaboard can not recognize these separately Wait 1 second or more when changing between your finger and the electronic pen When changed in a shorter time or when the electronic pen and your finger touch simultaneously the result is according to which one the elite Panaboard recognized first Confirm that the status LED lights when using the electronic pen e To avoid operating errors do not touch the penpoint when the electronic pen is not in use Inserting Replacing Batteries 1 Unlock the battery cover Q and open the cover Q reverse e When replacing the cover follow the procedure in 2 Insert replace the battery and then reattach the cover and lock it e Make sure to use a AAA alkaline battery and ensure that and face the correct directions Dispose of expired batteries quickly by covering the terminals in tape and following the disposal regulations in your country area Registering the Electronic Pen The elite Panaboard automatically detects electronic pens within approximately 10 m approximately 30 ft but if other electronic whiteboards are nearby electronic pens for those whiteboards may be detected accidentally Similarly other electronic whiteboards may detect electronic pens for the elite Panaboard In the following case
3. No Part Name illustration Q ty Remarks May not be included OT Warranty LE 1 depending on country area Notice e Screws 8 count for wall mounting are not included Please purchase screws with a size of M6 appropriate for your type of wall page 42 38 Operating Instructions Installation Manual Wall Mounting Construction Checking the Wall When mounting on a wall consult with your building s owner caretaker or construction manager to determine if the wall strength is sufficient to install the elite Panaboard For safety install the elite Panaboard only after thoroughly understanding the type of walls the appropriate types of screws and the construction method page 42 CAUTION Do not attach the electronic board to mortared walls Accidental electric leakage from the wall mounting plate bolts to metal laths or wire laths can cause heat smoke or fire l Necessary Tools and Parts not included with the elite Panaboard Drill Phillips head screwdriver Flat head screwdriver Measuring tape Level 8 screws M6 size ll Before Starting 1 Make sure that the wall is strong enough to support the elite Panaboard Rated strength greater than 1 962 N 200 kgf Notice If necessary reinforce the wall so that it is strong enough to support the elite Panaboard 2 Make sure that the location is large enough to accommodate the elite Panaboard Height greater than 2 100 mm 6 ft 10 5 8 in Width grea
4. ge e Screws 8 count are not included with the elite Panaboard Please purchase screws with a size of M6 appropriate for your type of wall Tighten the bolt so that it will not become loose e When drilling the holes and installing the wall mounting plates follow the procedure in Wall Types and Installation Procedures page 42 5 Mount the elite Panaboard on the wall e See Assembling the elite Panaboard For Wall Mounting page 49 Operating Instructions 41 Installation Manual Wall Types and Installation Procedures The method for attaching the wall mounting plates to the wall will vary depending on the wall s structure 42 Three available options are listed below Other methods may be necessary depending on the wall Metal or Concrete walls Stud plugs not included are needed Drill bit Metal or concrete wall Stud plug Z em Insert a stud plug in the hole oe Wall mounting plate Bolt Operating Instructions Drill 8 holes in the wall For the correct hole size refer to the instructions for the particular stud plugs used Insert the bolt through the hole in the wall mounting plate and tighten until the wall mounting plate is securely fixed to the wall Plasterboard walls Split wing toggles not included are needed Split wing toggle Wall mountin Plasterboard Q l J plate l TZ Bolt Arms Arms V M d Wooden walls Wood scre
5. Ed USB speaker USB Hub 2 Ports You can connect external devices directly to the elite Panaboard using these ports page 20 USB Port Directly connect a computer using a USB cable included AC Inlet Power Cord Notice The operation of external devices connected via the USB hub is not guaranteed e External devices connected via the USB hub that require a lot of power such as scanners or CD CD Rs may not operate properly For more information please consult the relevant dealer e When the elite Panaboard is used while peripherals connected to the USB hub are operating the response of the elite Panaboard may be delayed and the electronic pen may malfunction If such problems occur connect the peripherals directly to the computer Note e The elite Panaboard detects a change in electrostatic capacitance when touched by your finger For this reason it may not react to fingernails gloved hands or the electronic pen when a glove is worn e If you touch multiple points in a close area within 10 cm 4 ml this may be recognized as a single point or freehand lines may be drawn connected or intersecting Operating Instructions 15 Usage Electronic Pen Strap Loop For attaching straps if desired No strap is included Use a strap from which the cord will detach if excessive force is applied Selector Dial Selects features of the electronic pen L A d Ee i 4 Status
6. For detailed information about using the elite Panaboard software refer to the help menu For details on accessing the help information see Viewing the Help of the Software page 27 26 Operating Instructions Starting the elite Panaboard book The elite Panaboard book can be started in the following ways e If the elite Panaboard software has been installed click the icon in Select Function Menu e Double click the desktop icon of 57 elite Panaboard book e Click Start All Programs Panasonic gt elite Panaboard elite Panaboard book After Calibration Do Not Move the elite Panaboard or the Projector The following changes will bring the position of projection out of alignment with the position of your finger or the electronic pen and you will need to recalibrate the equipment The location of the projector changed The location of the elite Panaboard changed The image area or placement was changed due to changes in the zoom focus etc The resolution of the projector or the computer changed The resolution may be changed when you turn on your computer display If you are using the elite Panaboard installed on a stand be aware that accidentally hitting the elite Panaboard or pushing too strongly with the electronic pen while operating can move the stand s position which will result in misalignment of the projected image and the electronic pen s p
7. Package the unit as depicted in the diagram in Preparing for Removing the elite Panaboard from Its Packaging page 48 Notice e When handling the electronic board hold it by the edge frame and not the screen board Holding the screen board can result in damage Operating Instructions 55 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products packaging and or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste For proper treatment recovery and recycling of old products and used batteries please take them to applicable collection points in accordance with your national legislation and the Directives 2002 96 EC and 2006 66 EC By disposing of these products and batteries correctly you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling For more information about collection and recycling of old products and batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contac
8. D Wrench 2 A Washer i 7 Use the two wing bolts when securing the elite Panaboard to the stand 2 The included wrench is necessary for tightening and loosening the screw so keep it in a safe location 44 Operating Instructions Installation Manual CAUTION Before assembly be sure to lock the casters Locking the casters Push to lock Assembly Instructions 1 Assemble the fall prevention extension legs Operating Instructions 45 Installation Manual 2 Assemble the stand Assemble with the holes toward the front Locking caster side rear Locking caster side rear FRONT Notice Do not over tighten the screw GG Doing so can warp the support beams e Assemble the stand so that the locking casters are on the rear side 46 Operating Instructions Installation Manual 3 Pull the fall prevention extension legs down Note e When folding back the fall prevention extension legs release the lock as follows 4 Mount the elite Panaboard See Assembling the elite Panaboard For Mounting on a Stand KX B061 Sold Separately page 52 Operating Instructions 47 Installation Manual Assembly Instructions Preparing for Removing the elite Panaboard from Its Packaging Remove the 10 joints open the box remove the accessory box amp packing foam and open the plastic sheet of the eli
9. about 1 second intervals even after you turn the power switch off and then on again contact your dealer Error LED red is Turn off the power and turn it on SS blinking If the problem persists contact your dealer The elite Panaboard and your computer are not connected The computer does not Securely connect the elite Panaboard and your computer recognize the elite using a USB cable Panaboard The USB cable is connected to a USB hub Do not connect the elite Panaboard through a USB hub The connection between the computer and the Check that the elite Panaboard is in an operable state and that the elite Panaboard is USB cable is properly connected unexpectedly lost The elite Panaboard Other applications or anti virus software are active 5 response is delayed Shut down the other applications and anti virus software In Windows 7 there is a considerable delay in the elite Panaboard The USB operation is erratic response when you Unplug and reconnect the USB cable touch the screen board with your finger The projected image is misaligned 26 The point of control is out Perform the calibration again of alignment with your The display resolution pixel count has been changed 26 finger or the electronic Perform the calibration again pen e The edge of the projected image is curved 25 Perform Advanced Calibration Lines or comments drawn with your finger are not shown on
10. e Manipulate objects on the computer screen remotely by using the up and down buttons on the electronic pen e Supports Windows 7 multi touch functionality elite Panaboard book Use the elite Panaboard book software that supports elite Panaboard operations such as writing drawing attaching images and computer operations This software lets you save the contents of the screen on your computer and retrieve it for later use In built USB Speaker The elite Panaboard has an in built USB speaker Sound can be heard through the USB speaker when it is connected to a computer USB Hub Features The elite Panaboard comes with a 2 port USB hub as standard By connecting equipment such as scanners printers or external USB memory sources you can use their respective features directly with the elite Panaboard Input from the USB peripherals can be easily incorporated in whiteboard presentations Usage Scenarios For Education Create an effective learning environment by using your finger for direct control of a variety of educational software projected onto the elite Panaboard Write or draw on software screens with your finger or the electronic pen e With several tools at your disposal for aiding in explanations such as illustration and marker tools you can keep students attention through a dynamic screen display Draw your students interest by using the screen shade feature to show questions to students while hiding the answers an
11. Your Safety Battery Gei LC O00 G Use only the specified type of battery Using the incorrect type of battery can result in overheating burning or leakage of battery acid Make sure that the battery is installed with the correct polarity as indicated on the battery holder Incorrectly installed batteries may burst or leak resulting in injuries Do not use the damaged batteries Using damaged batteries may result in leaking Do not charge short heat break or throw in a fire as it may result in the battery leaking generating heat or bursting When disposing of the battery cover the battery contacts with insulation ex tape Direct contact with other batteries may result in leaking fire or explosion Do not solder the battery as it may result in the battery leaking generating heat or bursting Remove empty batteries immediately to avoid battery fluid leakage Avoid contact of battery fluid with eyes skin or clothing as this may result in irritation or injury In these cases do not rub the affected area and rinse thoroughly with clean water 10 Operating Instructions Electronic Pen elite Panaboard Do not use near medical equipment Do not bring into a surgery room intensive care unit critical care unit etc Electromagnetic waves generated by this device can affect equipment and can cause equipment to malfunction Do not use near automatic doors smoke detectors and other automati
12. as instructed below About Positioning the Image e When you are projecting an image make sure the image is inside the screen frame Project the Image as a Rectangle e Adjust the location of the projector to project at a right angle with the elite Panaboard 24 Operating Instructions If the image is projected trapezoidally the position may not be read correctly Adjust the projector so that the projected image is a rectangle Refer to your projector s documentation for information on adjusting the projected image NZ ENI ZS Set the Proper Resolution e Set your computer s and projector s resolutions to the most appropriate setting If the resolution is not set properly the image will be difficult to see Particularly if the projector s resolution is lower than the computer s thin lines can appear cut or broken Refer to your projector s documentation for information on adjusting the resolution Do Not Look Directly into the Projector Lamp e When using a projector try to avoid looking directly into the projector lamp Doing so can hurt your eyes Usage Using the elite Panaboard After Positioning the System Calibration About Calibration Calibration refers to setting up the elite Panaboard and projector so that lines and comments drawn with your finger or the electronic pen are displayed in the correct position Be sure to perform calibration before use
13. the computer screen e You are touching the screen board with a part of your hand other than your finger Use only your finger tip to touch the screen board You are touching too lightly with your finger Touch the screen board more firmly e Operating Instructions Appendix Symptom Possible cause and solution See page e You are using the electronic pen and your finger simultaneously While you operate the elite Panaboard with your finger the electronic pen produces the same result as when touching the 17 elite Panaboard with your finger After operating with your finger wait 1 second or more before using the electronic pen The electronic pen loses Other applications or anti virus software are active 5 the functions Shut down the other applications and anti virus software Buttons are e The electronic pen is low on batteries 17 unresponsive Replace the electronic pen s battery Lines written with the e The electronic pen is in low power mode 16 electronic pen are broken Turn the selector dial to change the mode or colors change e Peripherals are connected to the USB hub 15 Connect the peripherals directly to the computer e Another electronic whiteboard is in use nearby Use the Electronic Pen Registration Tool to register the _ electronic pen See Registering the Electronic Pen in Software Help for instructions on registering the ele
14. After you have set up the elite Panaboard project an image onto the screen board and use the elite Panaboard software installed on your computer to perform calibration Performing Calibration When the elite Panaboard is connected to your computer the calibration screen is automatically displayed Note e When using the projection screen of a projector to which the HD Visual Communication Unit has been connected refer to the help menu For details on accessing the help information see Viewing the Help of the Software page 27 _ H Turn on the elite Panaboard 2 Connect the elite Panaboard to your computer with the USB cable e The calibration screen is displayed e When the elite Panaboard software is installed on your computer the calibration screen is automatically displayed after the elite Panaboard software starts Restart your computer if you are prompted to do so After the computer has restarted connect the elite Panaboard to your computer with the USB cable e 3 Calibrate the equipment by using your finger to touch the center of the indicated points following the instructions on the screen for about 2 seconds each Xo e Touch the screen board at a right angle with your finger e After you touch an indicated point correctly the next point is shown automatically e When calibration has finished normally a completion dialog box is displayed Calibration Basic Calibr
15. LED green y Lights when the electronic pen power is on Blinks when the electronic pen battery is low Prepare a new battery and replace the old battery soon Up Button Performs the same function as pressing the Page Up key on a computer by remote control Battery Cover Down Button Performs the same function as pressing the Page Down key on a computer by remote control Menu Button Hold this button and touch the screen board with the pen to Penpoint Cover display the Drawing Menu page 26 Penpoint Note The up and down buttons can be used in a range of approximately 10 m approximately 30 ft from the elite Panaboard without obstructions Electronic Pen Features Draws with a marker in the selected color Black Red Blue Green Marker line thickness and other settings can be specified in the Drawing Menu e O Erases marker lines that you have drawn Eraser size and other settings can be specified in the Drawing Menu Eraser Highlights with a highlighter in the selected color Yellow Yellowish Green Highlighter line thickness and other settings can be specified in the Drawing Pink Menu e 1D Operates in the same way as using your finger a Mouse Puts the electronic pen in low power mode a 2 The pen detects motion to turn itself on or off automatically To conserve battery power put the pen in low power mode before carrying it while Low Power Mode walking when it is not in use
16. Panasonic Operating Instructions Electronic Board elite Panaboard Model No UB T 880 UB T880W de Stand is sold separately Installation Manual Included for qualified service personnel e To assemble this unit please refer to the Installation Manual on pages 35 through 55 e Before operating this unit please read these instructions completely and keep them carefully for future reference This unit is designed for installation by a qualified servicing dealer Installation performed by non authorized individuals could cause safety related problems with the operation of this equipment For U S A only e To locate the closest authorized dealer in your area please call 1 800 449 8989 Introduction Introduction Thank you for purchasing the Panasonic Electronic Board For optimum performance and safety please read these instructions carefully Feature Highlights By connecting the elite Panaboard to a computer and using a projector to display the contents of the computer s screen on the elite Panaboard you can do the following Touch and Electronic Pen Features e Manipulate objects on the computer screen by using your finger as a mouse e Use the electronic pen to draw or erase lines on the computer screen and to select line colors and other options es Up to 3 people at once can draw or erase lines on the computer screen by using their fingers e Save what you draw on the computer screen as image files
17. Panasonic System Networks Co Ltd 2010 F0510E7042
18. aaneduasinirentnnunanhstnscnsaansdasinnanieiandinenantinaaiunneinnusannciund 13 US LE 14 INGIUDER Accessories isciiitis dita isceidccoiceneninncedadrnndidendaicotenisinamnninnoniemuanneusneetadnneindundadarnncs 14 Names and Uses of the Parts vscicstincsacesisatssateacsnccedicnedencansntecsiscvadainenesunssdateticneadiuneladienes 15 Connecting External COMPONENMS cccccceeeseeseeeeeeeeeeeeeeeeeeeeeeeseeesseeeeseeeeseeeseeeeeeeeees 18 installing the SoftWare sssini unaensis naonn aaa aaea 22 Setting the EE 24 Using the elite Panaboard After Positioning the System Calibration keen 25 Viewing the Help of the Software ccsssssesceeesesseeeeeeeeeeeseneeseneeeseeeeesesseceneeeeeeeesenenes 27 Uninstalling the SoftWare scsssasitadeinccasicaieicanesaienaabduccisertbesatactenasnesacetuaansbbienidedinersencedaanindes 27 Uninstalling Panasonic Software Update Manager s ssssssssesssunnunnnrennnnnnnnnnnnnnnnnnnnne 27 Download the Latest Software siscsisciicestveciincusrcciviatnessdnniaadsitindvatnanendnvibantuddicentouredacinian 27 PMO EEN 28 ge 28 Cleaning the elite Panaboard ssc ccu cdscsessckssusatss ann conch ees idaenedeandeansusredouacaveadietiendenedduauas 28 Replacing the Battery in the Electronic Pen ccccceeeeeseeecceeeeeeeeeeseneeeeeeeeeeeeesees 28 Replacing the Penpoint of the Electronic Pen 29 TOUDISS E 30 Specifications scissors aaae a aa aaae aaa E Ee aaa kaadaa Eiana 32 Supplies amp Accessories
19. ach the electronic board to mortared walls Accidental electric leakage from the wall mounting plate bolts to metal laths or wire laths can cause heat smoke or fire Confirm the bolts of the unit are certainly caught by the wall mounting plate by pulling the unit after hanging the unit on the wall mounting plate if the unit is mounted on a wall Be sure to put on a glove to avoid electric shock or injury Installation Manual Included Accessories Confirm that the following items are included with the elite Panaboard No Part Name Illustration Q ty Remarks The illustration of the power cord is for the Power Cord 1 United States The 3 m 9 ft 10 1 8 in shape of the plug may vary depending on country area USB Cable 1 For computer 5 m 16 ft 4 7 8 in connection Va V Operating Instructions DVD ROM 1 Drivers IN A Application software Wall Mounting Plate Left 1 Wall Mounting Plate Right 1 Battery LRO3 AAA alkaline 1 A battery ed For electronic pen Electronic Pen ca 1 EE 1 For electronic pen Replacement A 2 4 GHz USB Wireless Adaptor is preinstalled on the elite oe USB Wireless IF i l Panaboard P FCC ID ACJ5Z6UE 608049 IC 216A UE608049 Y Operating Instructions Operating Instructions Ad 1 includes Installation Manual Operating Instructions 37 Installation Manual
20. ard and click Download the latest version Note e If Panasonic Software Update Manager is installed the software update programs are notified over the internet For details on the Panasonic Software Update Manager operations refer to Panasonic Software Update Manager help For the steps to take refer to Viewing the Help of the Software page 27 Operating Instructions 27 Appendix Daily Care When cleaning the elite Panaboard or inside the elite Panaboard make sure to switch off the power and unplug the power cord from the AC outlet Cleaning the elite Panaboard uN Gently wipe the elite Panaboard with a soft moist cloth Notice e The elite Panaboard is designed exclusively for projector images To remove marks written with a whiteboard marker or stubborn stains use whiteboard cleaner or neutral household detergent diluted with water e Do not use thinner benzine or abrasive chemicals to clean Doing so can result in discoloration 28 Operating Instructions Replacing the Battery in the Electronic Pen When the electronic pen battery is low the pen status LED blinks Continued use of the electronic pen can lead to poor performance Replace the battery as soon as possible See Inserting Replacing Batteries page 17 for details on replacing the battery Dispose of expired batteries quickly by covering the terminals in tape and following the di
21. ation succeeded Always use this calibration information To further reduce misalignment press the Advanced button and perform Advanced Calibration Advanced 4 If the edges of the image projected on the elite Panaboard are curved click Advanced to perform Advanced Calibration Go to the next step if not required e Advanced Calibration reduces misalignment of a projected image 5 Click OK e If the elite Panaboard and projector are fixed so that they will not move Wall mounted case select the Always use this calibration information check box and click OK to skip calibration from the next time you start the elite Panaboard software Operating Instructions 25 Usage Starting the elite Panaboard software When the elite Panaboard software is installed the amp 4 icon is displayed in the notification area when calibration is finished and you can use the elite Panaboard software e To display the Select Function Menu click the Menu Start Tab left side right side g on the screen with your finger Example of the Select Function Menu e To display the Drawing Menu touch the screen board while holding the menu button on the electronic pen Example of the Drawing Menu Note e When the elite Panaboard software is not installed the GN icon is not displayed in the notification area The Menu Start Tab and Drawing Menu of the electronic pen are not displayed on the screen
22. cally controlled equipment Electromagnetic waves generated by this device can affect equipment and can cause equipment to malfunction Use at least 22 cm 9 in away from pacemakers Electromagnetic waves generated by this device can affect the operation of pacemakers For Your Safety Power A When the unit is not used over an extended period of time switch it off and unplug it If an unused unit is left connected to a power source for a long period degraded insulation may cause electric shock current leakage or fire The unit should be used only with the power cord enclosed with the unit Installation and Relocation AG OO Do not position the unit in a location where it is unstable Do not place the unit in a hot humid or dusty environment Prolonged exposure to these adverse conditions may cause fire or electric shock To prevent fire or shock hazard do not expose this unit to rain or any type of moisture When moving the unit be sure to unplug the power cord from the AC outlet If the unit is moved with the power cord attached it can cause damage to the cord which could result in fire or electric shock Move this unit with two persons Otherwise this unit may fall down and cause injury Locking the casters Push to lock After installing or moving the unit lock the casters and set the fall prevention extension legs Operating Safeguards 00A Battery I
23. can damage it and cause fire or electric shock During thunderstorms do not touch the unit and plug It may cause an electric shock For Your Safety Installation and Relocation Gei Operating Safeguards G O A Have the unit installed removed and disposed of only by qualified service personnel When the unit will no longer be used in order to prevent it from falling do not leave the unit installed but remove it If the unit falls it can cause injury If metal fragments or water gets into the unit turn the unit off and unplug the unit immediately Contact your dealer for service Operating the contaminated unit can cause fire or electric shock Never open or remove unit covers that are screwed with screws unless specifically instructed in the Operating Instructions A high voltage component can cause electric shock Do not alter the unit or modify any parts Alteration or modification can cause fire or electric shock CHOKING HAZARD Keep the penpoint and battery out of reach of children to prevent swallowing Do not look into the lens while the projector is being used Strong light is emitted from the projector s lens If you look directly into this light it can hurt and damage your eyes Be especially careful not to let young children look into the lens In addition turn the projector off and unplug the power cord when you are away from the projector Operating Instructions 9 For
24. ctronic pen The electronic pen status The electronic pen is low on batteries 17 LED is blinking Replace the electronic pen s battery Because the elite Panaboard is designed exclusively for projector Marks written with a images you cannot erase the marks with a standard eraser whiteboard marker f 28 Use commercially available whiteboard cleaner or neutral cannot be erased i household cleaner diluted with water e The volume level of the elite Panaboard is low Adjust the volume using the volume dial The volume of your computer is low or set to mute Adjust the volume using the volume control in the notification area or uncheck the mute setting The sound level is low or epee e e The volume of the application is low no sound is output from 15 the speaker Adjust the volume of the application e g Windows Media Player The connection between the external audio input port and the VCR or DVD player etc is not correct Securely connect the external audio input port and the VCR or DVD player etc e The external device connected to the USB hub does not work properly e The elite Panaboard and external devices are not connected Securely connect the elite Panaboard and external devices A driver or application for enabling the use of external devices may not be installed on your computer Install the driver or application following the instructions in the
25. d incrementally showing the rest of the screen e The teacher can prepare materials before class to display on the elite Panaboard 2 Operating Instructions Introduction For Business e Visually convey your product s characteristics and create an appealing product presentation by displaying images and using your finger or the electronic pen to highlight key points e Information projected on the elite Panaboard at your company including what you add using your finger or the electronic pen can be displayed in real time at remote locations using videoconferencing equipment Things you should keep a record of For your future reference Date of purchase Serial number Dealer s name Dealer s address Dealer s tel no Abbreviations Windows refers to the Microsoft Windows operating system Windows XP refers to the Microsoft Windows XP operating system Windows Vista refers to the Microsoft Windows Vista operating system Windows 7 refers to the Microsoft Windows 7 operating system DirectX refers to the Microsoft DirectX application programming interface Trademarks e Microsoft Windows Windows Vista DirectX Windows Media and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e IBM is a trademark of International Business Machines Corporation in the United States othe
26. e party responsible for compliance could void the user s authority to operate this device About Using the Battery If a battery is used improperly the battery may leak causing corrosion of the unit or it may burst To prevent this always follow the precaution given below e If the electronic pen ceases to function because the battery has run out remove it immediately and dispose of it according to local regulations Leaving a drained battery in the electronic pen may result in leakage About Disposing of the Battery For Taiwan ZS Other Information Usage Note Operating the elite Panaboard near electrical appliances may cause interference Move away from the electrical appliances such as TVs radios cordless phone or wireless devices MEDICAL Consult the manufacturer of any personal medical devices such as pacemakers to determine if they are adequately shielded from external RF radio frequency energy The unit operates in the frequency range of 2 402 GHz to 2 481 GHz and the power output level is 0 001 watts Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so Hospitals or health care facilities may be using equipment that could be sensitive to external RF radio frequency energy No responsibility will be taken by our company with respect to consequences resulting from the use damage or both of the equipment For Euro
27. ed of only by qualified service personnel To ensure safe operation the power cord supplied must be inserted into a standard three prong AC outlet which is effectively grounded earthed through the normal wiring The fact that the equipment operates satisfactorily does not imply that the power point is grounded earthed and that the installation is completely safe For your safety if in any doubt about the effective grounding earthing of the power point consult a qualified electrician Electronic Pen elite Panaboard 36 Do not use near medical equipment Do not bring into a surgery room intensive care unit critical care unit etc Electromagnetic waves generated by this device can affect equipment and can cause equipment to malfunction Do not use near automatic doors smoke detectors and other automatically controlled equipment Electromagnetic waves generated by this device can affect equipment and can cause equipment to malfunction Use at least 22 cm 9 in away from pacemakers Electromagnetic waves generated by this device can affect the operation of pacemakers Operating Instructions Locking the casters Push to lock Gi After installing or moving the electronic board lock the casters and set the fall prevention extension legs If the unit is hung on a wall confirm the wall must be capable of supporting at least the following weight 1 962 N 200 kgf Do not att
28. elite Panaboard safely e When installing the elite Panaboard on a wall or on the stand perform installation with 2 people For Your Safety Notice To prevent severe injury and loss of life read this section carefully before using the unit to ensure proper AN WARNING and safe operation of your unit The following graphic symbols are used in this Installation Manual Safety check must be done by qualified service personnel after installing this option Denotes a potential hazard AN WARNING that could result in serious injury or death Be sure to disconnect the power cord while installing the unit Otherwise it may cause electric shock or injury Denotes hazards that could result in Be sure to use the specified parts for the AN CAUTION minor injury or installation Otherwise it may cause fire damage to the electric shock or injury unit Notes in the operating instructions or notes of labels on the cabinet chassis or parts should be observed These symbols are used to alert operators to a specific operating procedure that MUSNA DE perfomed Do not alter the unit and install Installing an altered unit can cause fire electric shock or injury These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the unit safely Operating Instructions 35 Installation Manual Have the unit installed removed and dispos
29. f the unit falls down or gets damaged turn the unit off and unplug the power cord Otherwise it may cause fire or electric shock Do not lean against the screen or on the cover lower even if the unit is mounted on the wall When using the stand be sure to watch your step so that you do not bump into or trip over the fall prevention extension legs The label of precautions is attached to the stand KX B061 sold separately When operating the screen board with your finger for a long time be sure to take regular breaks Continuous use for a long time may hurt your fingertip When the unit is not used over an extended period of time take the batteries out of the unit Otherwise the batteries may leak Do not use the leaked batteries Operating Instructions 11 For Your Safety Safety Information For United Kingdom only This appliance is supplied with a moulded three pin mains plug for your safety and convenience A 5 amp fuse is fitted in this plug Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362 Check for the ASTA mark E or the BSI mark g on the body of the fuse If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced If you lose the fuse cover the plug must not be used until a replacement cover is obtained A replacement fuse cover can be purchased from you
30. from the electronic board or the comupter Installation may take a few minutes to complete During installation Cancel is unavailable 9 When the installation wizard is displayed follow the on screen instructions and continue with the installation 10 When installation has finished click Finish Restart your computer if you are prompted to do so The elite Panaboard group and the Panasonic Software Update Manager group will be created in the Panasonic group in the program menu The following items are installed in the elite Panaboard group A function that you deselected on the Select Features screen in step 7 will not be displayed 1 elite Panaboard software elite Panaboard book Electronic Pen Registration Tool Operating Instructions Software Help Download the latest version HD Visual Communication Unit Screen Selection Tool The following items are installed in the Panasonic Software Update Manager group They are not displayed if they have not been selected on the Select Features screen in step 7 Panasonic Software Update Manager Help Note To view the Operating Instructions you must have Adobe Reader installed on your computer If your computer is connected to the Internet you can download Adobe Reader from Adobe s web site Operating Instructions 23 Usage Setting the Projector Set up your projector
31. he User Account Control window is displayed click Continue to continue with the installation es In Windows 7 if the User Account Control window is displayed click Yes to continue with the installation When the Select Features screen is displayed select the required function or deselect a function that you do not want and then click Next e Click the corresponding check box to select or deselect a function e You cannot deselect a function that is shown with a gray check box because it is a mandatory function e When you deselect a function that is already installed this function will be deleted uninstalled e If Panasonic Software Update Manager is already installed it will not be deleted uninstalled even when it is deselected For details on how to uninstall it refer to Uninstalling Panasonic Software Update Manager page 27 Usage 8 When the following screen is displayed confirm that the USB cable is not connected to your computer or the elite Panaboard and click OK e If the USB cable is connected to the elite Panaboard disconnect the cable and click OK e If Microsoft NET Framework 3 0 SP 2 or later or 3 5 SP 1 or later is not installed an installation screen will be displayed Follow the on screen directions to install these components Software Installation Software installation will begin Please confirm that the USB cable is disconnected
32. he elite Panaboard on the stand you can adjust its height to 4 different levels When changing the height remove the left and right screws from the back of the elite Panaboard and securely insert them at the desired height Torque greater than 1 Nem 10 kgf cm 9 Ibfein elite Panaboard Height Screw Position 100 mm 3 7 8 in Highest Standard 2nd from top 100 mm 3 7 8 in 2nd from bottom 200 mm 7 7 8 in Lowest Confirm that the elite Panaboard can operate e See Confirming the elite Panaboard Operation page 54 Turn off the power switch and unplug the power cord from the AC outlet Wipe the screen board surface e Gently wipe the screen board surface with a soft moist cloth ae Notice es Do not use thinner benzene or abrasive chemicals to clean Doing so can result in discoloration e Do not wipe the screen board with a dry cloth Doing so can cause static electricity build up Installation Manual Operating Instructions 53 Installation Manual Confirming the elite Panaboard Operation After assembling the elite Panaboard confirm that it operates properly by following the procedure below Checkpoints Action Operation Measure 1 Turn on the power Power LED green lights Normal operation Power LED green does not Check the power cord light or Error LED red i
33. in diagonal Model Number UB T880W General External Dimensions 1 320 mm x 1 900 mm x 117 mm Height x Width x Depth 4 ft 4 in x 6 ft 2 13 16 in x 4 5 8 in Weight 44 kg 97 lbs Input Unit Screen Board Size 1 175 mm x 1 845 mm Height x Width 3 ft 10 1 4 in x 6 ft 5 8 in Interactive Effective Area 1 036 mm x 1 842 mm 3 ft 4 3 4 in x 6 ft 1 2 in Features Height x Width 83 in diagonal Operating Instructions 33 Appendix Supplies amp Accessories 34 Replace the penpoint after it has become worn and no longer slides across the surface Optional Device Stand KX B061 Electronic Pen UE 608026 Stylus Pen UE 608027 Pointer UE 608028 Up Down Unit UE 608030 Stand Table Unit UE 608031 Short Throw Arm Unit UE 608032 Consumables Penpoint UG 6026 To purchase separately sold items contact your dealer Operating Instructions Installation Manual Installation Manual for qualified service personnel Request assembly of the Electronic Board stand and wall mounting from your dealer Before constructing or installing the elite Panaboard please read Installation Manual for qualified service personnel carefully Panasonic System Networks Co Ltd cannot be held responsible for accidents or damage to property resulting from incorrect installation e Please read For Your Safety pages 8 13 and pages 35 36 carefully and install the
34. line contact your dealer The cost of installing a grounding connection is not included in the price of the elite Panaboard The included power cord is exclusively for use with the elite Panaboard Do not use it with any other devices 18 Operating Instructions Usage 2 Connect the elite Panaboard to a computer using the USB cable included elite Panaboard Plug the B connector smaller connector into the elite Panaboard s USB port Computer Plug the A connector larger connector into a USB port on the computer e Do not connect the elite Panaboard via a USB hub This could result in erroneous operation Notice Do not connect the elite Panaboard to a computer via USB unless elite Panaboard driver software book is installed Only connect the USB cable after following the steps in Installing the Software page 22 to install the software To USB Port USB Cable Included a Kc Video Cable AC 3 Connect the computer to a projector e For instructions on connecting your computer and projector refer to the respecting instruction manuals Operating Instructions 19 Usage Connecting External Devices 1 Connect the external device to the elite Panaboard using a USB cable sold separately elite Panaboard Plug the A connector larger connector into the elite Panaboard s USB port External device Plug the B connector smaller connector into a USB p
35. manual for the external device e Operating Instructions 31 Appendix Specifications Model UB T880 UB T880W Number General Power AC 100 V 240 V 50 Hz 60 Hz 32 Power Consumption During Operation 0 5 A When power is OFF by the power switch 0 2 W Operating Environment Temperature 10 C to 35 C 50 F to 95 F Humidity 30 to 80 Storage Environment Temperature 20 C to 40 C 4 F to 104 F Humidity 15 to 80 Interface USB 2 0 No of Hub Ports 2 ports Electronic Transmission System GFSK Pen Electronic Pen Power LRO3 AAA alkaline dry cell battery x 1 Electronic Pen Battery Life 30 hours when used continuously at 25 C 77 F When using Panasonic LRO3 alkaline dry cell batteries Audio Audio Input Input level 309 mVrms 1 kHz 0 dB 10 kQ Features Stereo 1 system 3 5 mm 1 8 in stereo mini jack Audio Output 2 W 2 W maximum 4 W 4 W Operating Instructions Appendix Model Number UB T880 General External Dimensions 1 320 mm x 1 657 mm x 117 mm Height x Width x Depth 4 ft 4 in x 5ft 5 1 4 in x 4 5 8 in Weight 40 kg 88 Ibs Input Unit Screen Board Size 1 175 mm x 1 602 mm Height x Width 3 ft 10 1 4in x 5 ft 3 1 16 in Interactive Effective Area 1 175 mm x 1 567 mm 3 ft 10 1 4 in x 5 ft 1 11 46 in Features Height x Width 77
36. ming the elite Panaboard Operation page 54 50 Operating Instructions Installation Manual 10 Turn off the power switch and unplug the power cord from the AC outlet 11 Wipe the screen board surface e Gently wipe the screen board surface with a soft moist cloth T aS Jj CG Notice e Do not use thinner benzene or abrasive chemicals to clean Doing so can result in discoloration e Do not wipe the screen board with a dry cloth Doing so can cause static electricity build up Operating Instructions 51 Installation Manual For Mounting on a Stand KX B061 3 Hang the elite Panaboard on the stand with the screw heads Sold Separately 1 Attach the power cord e Connect the power cord to the elite Panaboard before installing on the stand sg _ 1 Il Toe i 2 Depending on the location of the outlet install the power cord as illustrated in the following diagrams e When attaching the power cord downward 4 Secure the elite Panaboard to the stand frame using the two wing bolts M5 x 12 mm 1 2 in nR i SS E 2 count included with the stand UR e When attaching the power cord along the lower side of the elite Panaboard 52 Operating Instructions When installing t
37. n select Help from the elite Panaboard book Help menu We recommend that you view the help using Internet Explorer 6 0 or later for Windows Uninstalling the Software If it is necessary to uninstall the elite Panaboard driver software book follow the procedure below 1 Turn on your computer and start Windows Log into an account with Administrator privileges 2 Select Add or Remove Programs from the Control Panel e In Windows Vista or Windows 7 select Uninstall a program 3 Select Panasonic elite Panaboard then remove it 4 Follow the on screen instructions 5 When uninstallation is complete restart your computer Uninstalling Panasonic Software Update Manager If it is necessary to uninstall the Panasonic Software Update Manager follow the procedure below 1 Turn on your computer and start Windows e Log into an account with Administrator privileges 2 Select Add or Remove Programs from the Control Panel e In Windows Vista or Windows 7 select Uninstall a program 3 Select Panasonic Software Update Manager then remove it Follow the on screen instructions When uninstallation is complete restart your computer oe Download the Latest Software Follow the procedure below to download the latest version of the software from the download web site 1 Turn on your computer and start Windows 2 On the Start menu point to All Programs gt Panasonic elite Panabo
38. ng EE 55 Operating Instructions 7 For Your Safety For Your Safety To prevent severe injury and loss of life read this section carefully before using the unit to ensure proper and safe operation of your unit This section explains the graphic symbols used in this manual Denotes a potential A h d that Id WARN ING eal in ae injury or death Denotes hazards that Id It i AN CAUTION I m damage to the unit These symbols are used to q Ap D L alert operators to a specific operating procedure that must not be performed These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the unit safely 8 Operating Instructions 0S O 00 For Users Power and Ground Connection The power source voltage of this unit is listed on the nameplate Only plug the unit into an AC outlet with the proper voltage If you use a cord with an unspecified current rating the unit or plug may emit smoke or become hot to the touch When you operate this product the power outlet should be near the product and easily accessible To ensure safe operation the power cord supplied must be inserted into a standard three prong AC outlet which is effectively grounded earthed through the normal wiring The fact that the equipment operates satisfactorily does not imply that the power point is grounded earthed and that the ins
39. nts are available for purchase separately page 34 The warranty may not be included depending on country area About Using the DVD ROM To prevent damage to the DVD ROM Do not touch or write on the surface of the disc e Do not leave the disc out of the protective case e Do not leave the disc in the direct sunlight or near heat sources Do not place heavy objects on the disc case or drop the case To clean the disc hold the disc by its edges and wipe it from the center to the edges with a dry soft cloth 14 Operating Instructions Usage Names and Uses of the Parts Screen Screen Board Detects the position of your finger or the electronic pen Project the contents of a computer screen using a projector Power Switch Power LED green Turns the elite Panaboard on or off each time the power switch is pressed Lights green when the power is on Error LED red Blinks red when an error occurs Pen Tray D the center of the door to open the pen tray which can hold the electronic _ l USB Speaker Outputs sound from a computer or the audio input port in stereo Power Inlet for Optional Devices Il Is for optional elite Panaboard accessories only Do not use this inlet with other devices ga Volume Dial bt Adjusts the volume of the speaker at External Audio Input Port Connect the audio output port of a VCR or DVD player etc to this port and hear sound through the
40. o Ltd is not responsible for accidents or injuries caused by but not limited to the following 1 Altering the device or improper installation construction 2 Using the device for purposes beyond its intended use 3 Earthquake fire flood tidal wave hurricane lightning or other natural phenomena 4 Natural aging of the building or similar phenomena Operating Instructions 5 Introduction For FRG Users For Germany Only Note Machine noise information regulation 3 GPSGV the maximum sound pressure level is 70 dB A or less in conformity with EN ISO 7779 This device is not intended for use in the direct field of view at visual display workplaces To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view 6 Operating Instructions Table of Contents Table of Contents For YOUR Safety icion aaa aai aaa Eaa AE NENE aE EA ARENE 8 For Your Safety ccceesinsecsnceapeaansnmncsansansnannteindsinankoesmnanpnasions tannin ans arnore auaa a auas 8 For USOT S iv svisannnananseaninsanniidenewannusonaseinauslen admssveavinnuninunedal saasaa sepa E aiaa EE auaa ENUS Ena Sakes 8 Safety Information For United Kingdom only sssssssnununneennnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 12 Precauti ns ssssosiriusinisusnesusenra peisses uasai Ki Paa iadaaa aeaa S NENE sabu ES EHu Sra Eiu saana raais 13 Other INTO ATG scisirscnscstcendnsasinenmntzananns
41. ock the casters 5 Pull the fall prevention extension legs down Operating Instructions 21 Usage Installing the Software To install the elite Panaboard driver software book follow the procedure below Notice ech 22 Do not connect the USB cable until the installation is completed e Do not connect more than 1 elite Panaboard to the same computer Doing so can cause erroneous behavior on the computer Turn on your computer and start the Windows operating system Log into an account with Administrator privileges Insert the included DVD ROM into the DVD ROM drive e The setup screen will be displayed e If the setup screen does not appear select your DVD ROM drive in Explorer and double click Menu exe e In Windows Vista or Windows 7 if the Autoplay dialog box is displayed click Run Menu exe When the elite Panaboard screen is displayed click the type of device you are using When the Menu screen is displayed click Read Me First Menu UB T880 Ver x xx Read Me First Install elite Panaboard e After the system requirements are displayed make sure that your computer meets the requirements Operating Instructions Click Install elite Panaboard on the Menu screen If you agree to the terms in the END USER LICENSE AGREEMENT select I accept the terms in the license agreement and then click Next In Windows Vista if t
42. oeroet ia eE i a E ea aE E EAEE E AOSE ENERE 34 Installation Manual iisesececcscec cc cacttc ies iradte cece caesveveueacegectiiies Miduedieceeenceeedss 35 Installation Manual for qualified service personnel 35 F r Your Safety osere nines eich a a eee seage re EE AKSE NNN raaa 35 EE ege a a N a a a e 35 included Accessories scscsesiseviveceicecnineaess cussdantnesasuedeiurehdstnsnsuussistsiescwbensnsucedanupindandastnrnss 37 Wall Mounting Ke e EE 39 Checking the eege 39 Installing the Wall Mounting Plates cccccssseeeeenseeeeeeeeeeseeeeeeeeeeeseneeeeeeeeeeeeeenneesoes 40 Wall Types and Installation Procedures cccececeeeeeeeeeeeeeeeeeeeeeseenaaaeeeeeeeeeeseneeeeeeeeeees 42 Stand KX B061 Assembly Sold Separately cccccccsseseeeeeeeeeeeeeeneeeeeeeeeeeeseeeeeeeeeneess 44 Included Bl ce gcc Aerie rhe interdia Ere mR nina Rene ene er eer ne ene eee net EEES 44 ue Ee EE 45 Assembly INSUIUCUONS wisseiicrincecsincontnrnecnernisaiusdsaceiaisiccbewsniaduncitesiddnnandasacudiutaduauandsdedecinenin 48 Preparing for Removing the elite Panaboard from Its Packagoimg 48 Assembling the elite Pamaboard cccceeeeesseeeneceeeeeeeeeeeeneeeeeeeeeeeeeesseeeeeeeeeeeeeeneees 49 Confirming the elite Panaboard Operation cccccccceseseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 54 Confirming the Interactive Features scascteciac cicsscsnccactcasvetaadenececdetensadecteliateauevenccoeneieedanaies 54 Repackagi
43. ort on the external device To USB Port USB Cable Sold Separately Flatbed Scanner About the Usage Location Do not place the elite Panaboard where it is directly exposed to sunlight e Do not use the elite Panaboard in a location less than 10 C 50 F or in a location subject to extreme changes in temperature Note e The elite Panaboard may not work properly when used in one of the above locations e Operating the elite Panaboard near electrical appliances may cause interference Move away from the electrical appliances 20 Operating Instructions Usage Volume Control e The volume of the USB speaker on the elite Panaboard can be controlled using the Volume Dial the volume of Windows and the volume of the application being used To adjust the volume use the Volume Dial or adjust the volume of the application Power Switch e After turning the elite Panaboard off wait more than 2 seconds before turning it back on Moving the elite Panaboard When Using the Stand Sold Separately 1 After confirming that the power is off disconnect the power cord and USB cable 2 Release the locks on the casters Note e When folding back the fall prevention extension legs release the lock as follows 3 Move the elite Panaboard avoid banging or shaking the board Notice e Always move the elite Panaboard with 2 people e Do not drag or step on the cable 4 L
44. osition Make sure to lock the stand s casters when using the elite Panaboard as failing to do so can cause misalignment Performing the Recalibration Displaying the Calibration Screen Manually e When the elite Panaboard software is already installed Click the amp icon in the notification area and click Calibration in the pop up menu e When the elite Panaboard software is not installed Double click the desktop icon of lt _ elite Panaboard Calibration Tool 8 Exiting the elite Panaboard software Click on the SN icon in the notification area and select Exit from the menu Usage Viewing the Help of the Software Follow the procedure below to view the help of the software installed on your computer 1 Turn on your computer and start Windows 2 Open Software Help from the Start menu Start All Programs Panasonic elite Panaboard Software Help e General help information of the installed software is displayed 3 Open Panasonic Software Update Manager help from the Start menu Start All Programs Panasonic gt Panasonic Software Update Manager Help e Panasonic Software Update Manager help is displayed Note e To access the help information of elite Panaboard software and Electronic Pen click the amp icon in the notification area and select Help from the pop up menu e To access elite Panaboard book help informatio
45. pean Union EU Panasonic System Networks Co Ltd declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio amp Telecommunications Terminal Equipment R amp TTE Directive 1999 5 EC Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting http www doc panasonic de Contact to Authorised Representative Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Operating Instructions 13 Usage Included Accessories Check that all of the following items are included with your elite Panaboard In the event that an item is missing please contact your dealer List of Accessories Power Cord USB Cable 3 m 9 ft 10 1 8 in l 5 m 16 ft 4 7 8 in A SES 1 oJ Lo NA AAA Battery LR03 Penpoint Disposable Electroma Pen i Replacement l Operating Instructions 2 4 GHz USB this document 1 Waman 1 Wireless Adaptor 1 LP E A 2 4 GHz USB Wireless Adaptor is preinstalled on the elite Panaboard FCC ID ACJ5Z6UE 608049 IC 216A UE608049 Note e The illustration of the power cord shown above is for the United States The shape of the plug may vary depending on country area Stand is sold separately e Store the extra penpoint along with this operating manual e Replacement penpoi
46. r countries or both e Intel and Pentium are trademarks of Intel Corporation in the U S and other countries e Adobe Reader and Flash are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries e All other trademarks identified herein are the property of their respective owners Operating Instructions 3 Introduction Help of the Software Instructions for elite Panaboard software and elite Panaboard book included are provided in the help information accompanying the software For details on accessing this information see Viewing the Help of the Software page 27 Federal Communications Commission and Industry Canada Requirements For United States and Canada Only This device complies with Part 15 of FCC Rules and RSS Gen of IC Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of this device Federal Communications Commission Requirements For United States Only Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio f
47. r local Panasonic Dealer IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR PREMISES THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET If a new plug is to be fitted please observe the wiring code as shown below If in any doubt please consult a qualified electrician WARNING This appliance must be earthed IMPORTANT The wires in this mains lead are coloured as follows Green and Yellow Earth Blue Neutral Brown Live 12 Operating Instructions As the colours of the wire in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire that is coloured GREEN AND YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN AND YELLOW The wire that is coloured BLUE must be connected to the terminal in the plug that is marked with the letter N or coloured BLACK The wire that is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED How to replace the fuse Open the fuse compartment with a screwdriver and replace the fuse and fuse cover For Your Safety Precautions Any changes or modifications not expressly approved by th
48. requency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Warning To assure continued FCC compliance the user must use only shielded interface cable and the provided power supply cord Also any unauthorized changes or modifications to this equipment would void the user s authority to operate this device RF Exposure Warning This Electronic Board may be used with below referenced optional low power 2 4 GHz USB Wireless Adaptor and Electronic Pen and may not be co located or operated with any other antenna or transmitter These transmitters comply with FCC radiation exposure limits set forth for uncontrolled environment general population to meet the FCC radio frequency RF Exposure Guidelines in FCC OET Bulletin 65 Supplement This satisfies RF exposure evaluation by calculated Maximum Permission Exposure MPE without the need for tested localized specific absorption rate SAR measurements Industry Canada Requirements For Canada Only This equipment complies with IC radiation exposure limits set forth for an uncontrolled equipment and meets RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that are deemed
49. s register the electronic pen to the elite Panaboard e Buttons on the electronic pen are unresponsive e The elite Panaboard responds as if you were operating it but you are not e The elite Panaboard operation is erratic Once you register an electronic pen it cannot be used with another electronic whiteboard To use registered electronic pens with another electronic whiteboard unregister the pens See Registering the Electronic Pen and Unregistering the Electronic Pen in Software Help for instructions on registering and unregistering the electronic pen For details on accessing the help information see Viewing the Help of the Software page 27 Operating Instructions 17 Usage Connecting External Components 1 Connect the power cord included to the elite Panaboard and plug the power cord into an AC outlet Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is easy to unplug If you are using the optional stand plug the power cord into the AC inlet and secure the cord as shown in the illustrations below When attaching the power cord downward When attaching the power cord along the lower side of the elite Panaboard About Grounding If you cannot connect the grounding
50. s See step 1 of Assembling the elite Panaboard blinking e For Wall Mounting page 49 For Mounting on a Stand KX B061 Sold Separately page 52 Confirming the Interactive Features 1 Following the procedure in Installing the Software page 22 install the software and connect the included USB cable 2 Confirm that the interactive features are operating correctly If a projector is not available confirm operation using only the elite Panaboard and computer e When the elite Panaboard software starts the calibration screen is displayed on the computer screen Perform tentative calibration by touching the locations on the elite Panaboard that correspond to the points displayed on the computer screen in the order shown for about 2 seconds each For precise adjustment it is necessary to use a projector Approx 100 mm 3 7 8 in Approx 100 mm 3 7 8 in Confirm operation by writing on the screen board with the electronic pen and checking that the writing is displayed on the computer s screen Your writing with the electronic pen will not appear on the screen board itself 54 Operating Instructions Installation Manual Repackaging To repackage the elite Panaboard perform steps in the following Assembling the elite Panaboard in reverse For Wall Mounting page 49 For Mounting on a Stand KX B061 Sold Separately page 52
51. sposal regulations in your country area For Taiwan ZS CF Ka Appendix Replacing the Penpoint of the Electronic Pen As the penpoint of the electronic pen becomes worn the penpoint will no longer slide easily across the surface Continuing to use the electronic pen in this condition may make the screen dirty and cause malfunction Replace the penpoint with a new one as soon as possible 1 Remove the penpoint cover La 2 Remove the old penpoint and attach the new one O RAS ow ne R A BEN oe wer 3 Reattach the penpoint cover OD bk O Operating Instructions 29 Appendix Troubleshooting When experiencing problems please refer to the table below for possible solutions If the problem persists contact your dealer In the case of the kinds of trouble which are not described in the table below refer to Troubleshooting in the software help 30 Symptom Possible cause and solution See page The LEDs do not light Check that the power cord is properly plugged in when the power switch is If the problem persists unplug the cord momentarily wait about turned on 2 seconds and plug it in again You turned on the power switch while touching the screen board The Error LED red Do not touch the screen board for about 3 seconds after turning blinks twice repeatedly at on the power switch If the Error LED red continues to blink
52. t your dealer or supplier for further information These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples This symbol might be used in combination with a chemical symbol In this case it complies with the requirement Cd set by the Directive for the chemical involved Information on Disposal in other Countries outside the European Union Information on Disposal for India For the purpose of recycling to facilitate effective utilization of resources please return this product to a nearby authorized collection center registered dismantler or recycler or Panasonic service center when disposing of this product Please see the Panasonic website for further information on collection centers etc http Awww panasonic co in wps portal home Panasonic Corporation of North America One Panasonic Way Secaucus New Jersey 07094 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Panasonic Marketing Europe GmbH Hagenauer Strasse 43 65203 Wiesbaden Germany For information of Compliance with EU relevant Regulatory Directives Contact to Authorised Representative Panasonic Testing Centre Panasonic Marketing Europe GmbH For EU only Winsbergring 15 22525 Hamburg Germany Panasonic Corporation Web Site http Awww panasonic net
53. tallation is completely safe For your safety if in any doubt about the effective grounding earthing of the power point consult a qualified electrician If the plug cannot be inserted into the AC outlet contact a licensed electrician to replace the AC outlet with a properly grounded earthed one Do not defeat the grounding earthing plug ex do not use a conversion plug S006 OOo oc Plug the power cord firmly into an AC outlet Otherwise it can cause fire or electric shock Do not pull bend rest objects on or chafe the power cord and plug Damage to the power cord or plug can cause fire or electric shock Do not attempt to repair the power cord or plug If the power cord or plug is damaged or frayed contact an authorized service representative for a replacement Ensure that the plug connection is free of dust In a damp environment a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time Never touch the plug with wet hands Danger of electric shock exists Stop operation immediately if the unit emits smoke excessive heat abnormal smell or unusual noise These conditions can cause fire or electric shock Immediately turn the unit off and unplug the power cord and contact your dealer for service When disconnecting the unit grasp the plug instead of the cord Pulling on a cord forcibly
54. te Panaboard Shipping Box Accessory Box Contents e Power Cord e USB Cable e Wall Mounting Plate Cushioning Right Left material e Battery e Electronic Pen e Penpoint e Operating Instructions Board e Warranty Electronic Notice e When handling the electronic board hold it by the edge frame and not the screen board Holding the screen board can result in damage e The packing materials in the shipping box are necessary for repackaging so keep them in a safe place Note The warranty may not be included depending on country area 48 Operating Instructions Installation Manual Assembling the elite Panaboard For Wall Mounting 1 Attach the power cord e Connect the power cord to the elite Panaboard before installing on a wall Mo 1 GN a tS Power Cord 2 Depending on the location of the outlet install the power cord as illustrated in the following diagrams When attaching the power cord downward J e When attaching the power cord along the lower side of the elite Panaboard a Remove the push turn rivets 4 on the fasteners on the bottom of the board e Turn the push turn rivets counter clockwise with a Phillips head screwdriver When the fastener pops up the part can be removed
55. ter than 2 000 mm 6 ft 6 3 4 in 3 Make sure that the AC outlet is within 3 m 9 ft 10 1 8 in of where the elite Panaboard will be mounted and that it will not be behind the elite Panaboard Operating Instructions 39 Installation Manual Installing the Wall Mounting Plates 1 Ensure that the wall is strong enough to support the elite Panaboard Rated strength greater than 1 962 N 200 kgf 2 Using the measuring tape and level mark the 8 locations to insert the screws UB T880 421 8 mm 208 2 mm 1 ft 4 19 32 in 8 3 16 in 40 mm 1 9 16 in 1 006 mm 3 ft 3 19 32 in 324 2 mm 1 ft 49 64 in 23 5mm 220 9 mm 15 16 in 8 11 16 in 543 3 mm 208 2 mm 1 ft 9 3 8 in 8 9 16 in 1 006 mm 3 ft 3 19 32 in 1 ft 49 64 in 23 5mm 220 9 mm 15 16 in 8 11 46 in Note The dotted line in the illustration represents the outer edge of the elite Panaboard 3 Drill 8 holes for the wall mounting plates e Drill holes that are appropriate for the screws you are using 40 Operating Instructions Installation Manual 4 Install the wall mounting plates using the 4 screws 2 screws are used for each wall mounting plate The remaining 4 screws are used after installing the elite Panaboard on the wall page 50 UB T880 UB T880W 813 st lt r Tele JAA 40 mm 1 9 16 in ra 1 006 mm 3 ft 3 19 32 in pe 23 5 Sein Ge 220 9 8 16 in
56. to comply without testing of specific absorption ratio SAR 4 Operating Instructions Introduction Warning about saving data When the system storage device or any of its optional storage device is adversely effected by operational errors static electricity electrical noise vibration dust or when the power has been cut off due to malfunction repair or inadvertently the memory contents may be lost or changed Before operating the system make a point of reading the precautionary notes in the Operating Instructions and the help information and observe them during operation Please observe carefully the following precaution e Make absolutely sure that all important data is saved by back up or the original is saved The manufacturer hereby declares that it cannot be held accountable for any loss or change in any data stored on floppy disks hard disks optical disks or other memory devices System Requirements Computer IBM PC AT compatible with a DVD ROM drive CPU Intel Pentium 4 processor or later Interface USB 2 0 Note e For details about the system requirements refer to Read Me First page 22 in the install menu of the included DVD ROM e Even when the system requirements are met the elite Panaboard response may be delayed or the electronic pen may malfunction if other applications anti virus software etc are active Exemption of Liability Panasonic System Networks C
57. ws not included are needed Wall mounting plate Wooden wall Notice Installation Manual Insert the bolt through the hole in the wall mounting plate and into the hole in the wall so that the arms of the split wing toggle are horizontal For the correct hole size refer to the instructions for the particular split wing toggles used After the arms expand pull the wall mounting plate out until the arms of the split wing toggle grip firmly into the wall Tighten the bolt until the wall mounting plate is securely fixed into the wall Insert the wood screw through the hole in the wall mounting plate and tighten until the wall mounting plate is securely fixed to the wall For the correct hole size refer to the instructions for the particular wood screws used When mounting onto a thin panel use reinforcing material and mount in the same manner as when mounting on plasterboard walls Operating Instructions 43 Installation Manual Stand KX B061 Assembly Sold Separately Included Parts Check that the following parts are included with the stand KX B061 No Part Name Illustration Q ty O Stand Base 2 Support Beam 2 Cross Bar A 2 Gi Cross Bar B 1 Screw M6 x 45 mm D 3 4 in Gg 10 Two wing Bolt M5 x 12 mm 1 2 in 1 Support Bracket 2 Fall prevention Extension Leg L 4 Screw M6 x 60 mm 2 3 8 in F Nut 7
Download Pdf Manuals
Related Search