LU-202 Large Capacity Unit INSTALLATION MANUAL
Contents
1. A Top door of the LU 3 Adjusting directions vertical opening level Example If the top end of the LU is too far away extend the LU adjuster feet to raise the LU 1 Loosen the nuts front rear 2 places on the LU adjuster feet using a wrench 2 Lower the up down plate to the very bottom and use a flathead screwdriver to extend the LU adjuster feet from inside the LU to raise it 3 Adjust the front and rear adjuster feet to make the LU parallel to the direction the paper passes Note Check again the vertical opening 4 When the adjustment is complete tighten the nuts front back 2 places on the LU adjuster feet A03WIXE012SA cog J OME G Adjuster foot rods l K Paper Size Setting 1 Open the top door of the LU 2 Loosen the knobscrews 2 pcs each of the paper guide side plates adjust the plates to the size of the paper and tighten the knobscrews 3 Loosen the knobscrews 2 pcs of the end guide plate adjust the plates to the end of the stack of paper and tighten the knobscrews A03WIXE013SA VI Skew adjustment Make a sample copy and if it is skewed move the set position of the positioning pin at the LU bottom plate AO3WIXE014SA E 52. LU 2 02 Large Capacity Unit INSTALLATION MANUAL Applied Machine C6501 C6501 P C5501 C6500 C6500P C5500 C65hc C7000 C7000P C6000 C70hc COLOR MFP 65ppm 55ppm COLOR PRESS 71ppm 71ppm 70ppm 70ppm 60ppm 60ppm Product code AOU0 A0U1 A0U2 A03U A03V A0E7 A0Y8 A1 DU A204 A1 DV A205 Note Ill Installation procedures Take the same procedures though the machine 1 Remove all the locking tapes put on the LU photographs are different from the ones illus trated in the procedures Accessory parts Locking tapes Locking tape LU fixing plate A03WIXC001SA 2 TP screw M4x10 TP screw M3x6 4 Paper type label Locking tape og Accessory parts i ancora North America only ll Preparation Prior to Installation 1 Turn the machine s Sub and Main switches OFF poesind tapes and unplug the power cord Locking tapes 2 Do not turn the power switch ON unit all the lock ing materials are removed from the LU Locking tapes AO3WIXE001SA E1 A03W955044 2 Attach the enclosed paper type label to the posi tion as shown below Note Only for products bound for North America 3 Open the right side door of the machine put the LU fixing plates 2 pcs in the door and close the door Right side door LU fixing plates A03WIXE002SA 4 Secure the LU fixing plates 2 pcs with screws from the accessory parts TP screw M4x10 4 pcs through the front screw holes to the machine TP s
3. crews M4x10 AO3WIXE003SA 5 Remove the right cover 3 2 screws Note Remember to remove the right cover Right cover 3 A03XIXE007SA 6 Cut off the split cover on the right side of the machine with a nipper Split cover Right side cover A03WIXE005SA 7 Pull out the connector plate screws Connector plate AO3WIXEO06SA 8 Connect the LU 202 connectors 3 to the machine aes el Mven 9 Fix the connector plate and wire relay bracket together TP screw M3x6 2pcs TP screw M3x6 2pcs A03WIXE008SA 10 Install the connector plate using the 2 screws removed from the connector plate a r _ rt AO3WIXEO09SA E 3 11 Open the LU front door and mount the LU on the LU fixing plates Be sure to meet the positioning pin of LU fixing plate to the junction hole of the LU bottom plate on mounting l 12 Fix the LU to the LU fixing plate with the screws TP screw M4x10 2 pcs from the accessory parts g AO03WIXE010SA IV Vertical opening level adjustment 1 Adjust the height of the adjuster feet to make the vertical opening between the machine and the LU even A03WIXCO003SA 2 Open the top door of the LU and check if the machine s paper passing area is parallel to the gap in the top door If it s not parallel adjust the heights of the front and rear adjuster feet Coe ort F O OOO OERIOOOOOOCON OOOSOSOOOO D ee 7
Download Pdf Manuals
Related Search