APT R Power Assist Folding Electric Bicycle USER MANUAL Model
Contents
1. Lower the mudguard by Pull the trigger of the pedal and fold the loosening the tighten knob pedal simultaneously Repeat the same steps for the other side of the pedal 2007 5 11 12 Pull out the safety pin from the Fold the front amp rear locking hole frame assembly as shown Insert the safety pin into the locking holes to engage the front and rear frame assembly Loosen and then lower the lever to retreat the pin to release the clamping of the handle bar Keep the crank pedals on the level while folding the handle bar Fold the handle bar downward toward the same side of the kickstand and beyond the level of crank pedals Note Move the cables away from the quick clamp to prevent accidental scratch on cables while folding The folding steps are completed 2007 5 11 13 steps to restore the E Bike N Po 4 Remove the safety pin from Unfold the front amp rear frame the locking hole assembly as shown Coincide the locking holes and insert the safety pin to engage the front and rear frame assembly securely Lower the lever by fingers as shown to retreat the pin for the engagement of the handle bar Restore the handle bar and then heighten the lever to engage pin and slot in and then clamp the lever to secure the handle bar Note Move the cables away from the quick clamp to prevent accidental scratch on cables while unfolding 2007 5 11 14 Adjust the tighten knob to fasten the mudg2. Electric Bicycle unless approved and authorized by SUNRUNNER will automatically invalidate the warranties Standard warranty does not extend to consumable items and parties other than the original purchaser The preceding guidelines are intended to assist you in the safe operation of this APT Power Assist Folding Electric Bicycle Should you have any questions about the correct operation of the APT Power Assist Folding Electric Bicycle please contact your authorized dealers Model Name SUNRUNNER SFB 18 Provider Stamp Serial No P N 300905 25 2007 5 11 18
3. 007 5 11 9 Check the battery specification or consult your authorized dealer Stop charging immediately and check if there is a problem with the charger or the batteries Caution 1 Make sure the DC output correspondingly connected to the battery to be charged is at the rated voltage or it may cause unexpected danger or damage For your safety do not charge the batteries for longer than 24 hours Do not expose the charger to the rain water or a humid place Do not use the battery charger near flammable articles or in unventilated places For your safety do not short circuit output plug or it may cause unexpected danger or damage Use the specified charger only for LiFePO Lithium Iron Phosphate Based Battery Pack 24V supplied by PMMC Always use the battery charger and power cord supplied by PMMC Before plugging in the power cord of the charger please confirm that the local power supply corresponds with the requirement of the charger The manufacturer will not be responsible for any damage or injury due to improper or unsafe use of the battery charger 2007 5 11 10 Cover of Battery Case Features Charging Port Charging Port e Main Switch Function Switch Depressed Function Position LED Light of Start the controller is function of lightened up Power Assist Both LED Lights by pedaling on controller and battery case are lightened up 0 Poweroff o The LED Light of cont
4. 2007 5 11 5 The operating instructions of derailleur Shimano Inter 3 Gear The E Bike is equipped with the Shimano Inter 3 3 speed gear shifting at the rear wheel axle It is easy to change the gear ratio by shifting the gear change handle while riding Handle peer Riding Gradient Speed Gear Ratio At a moderate gradient To save your energy while climbing a slope If the derailleur can not be performed with its intended function please contact your authorized dealer for adjustment To shift the derailleur the steps as blow should be followed 1 Stop pedaling to be ready for shifting the gears while riding 2 Only shift one gear one time while switching the gear change handle 3 Start pedaling for your riding Note If you shift the gears without stopping pedaling a clash may be heard due to gears shifting over dynamic moving parts Adjust saddle height A y an ea 2 1 Loosen the clamp lever 2 Adjust the seat post to the desired position 3 Take heed of the maximum height 4 Tighten the clamp lever markings MIN INSERTION on the tube of the seat 2007 5 11 6 Regular check for safety before riding ils Check Tire Pressure Check the tire pressure of front and rear wheel to be maintained at 50PSI or 3 5Bar Check if the tread of tires with excess worn out should be replaced Check Power Assist The power assist will be cut off when one of handbrakes is engaged or the peda
5. As the last battery indicator light starts flashing the rider can continue to ride the E Bike Remarks for approx 2 KM further 2 Go Button Kit and Throttle Handle Kit are optional 3 The maximum weight capacity of the E Bike is around 90 kgs The maintenance guarantee period of this product except consuming parts begins on the day of purchase and ends at one year later Only the original purchaser is entitled to the guarantee Performance and mileages of the unit will be varied with the factors such as battery condition temperature terrain wind speed tire pressure rider weight and the maintenance etc PMMC reserves the right to revise the wording and specification of the E Bike without prior notice 2007 5 11 17 Power Assist Folding Electric Bicycle DISCLAIMER Congratulations on your purchase of SUNRUNNER APT Power Assist Folding Electric Bicycle This APT Power Assist Folding Electric Bicycle is not intended to be used by individuals with physical limitations that could prevent the user from operating the APT Power Assist Folding Electric Bicycle safely PMMC disclaims all responsibility for any personal injury or property damage which may occur as a result of improper or unsafe use of its products Mechanical or electrical defects will be dealt with on a contingency liability basis Warranty is only valid when genuine SUNRUNNER parts are used All modifications on the APT Power Assist Folding
6. USER MANUAL Model SFB 18 Table of Contents MALEO GUC HOM esate a trees ee ioe et recent arenes eee 3 PS LUN CS sertgecsetis banter E E 3 Safety WArNINGS cccc cece ee eeee cece ee eeeeeeeeeeeeeeeeeeeneuaueneees 4 Uce GUIDING erremu rien eE E o Batteries and Charging ccccccceeeeceee eee e eee e ee eenateeeaees 8 11 Steps to fold the E Bike 0 ccc cece eee eee eee e ees 12 13 Steps to restore the E BIKe 0 cece cece cece eee eee e eens 14 15 TTOUDIC SHOOUING a2 acinceaiuce esse aadtonenentoaneemonctonmn Eaa 16 SPECIMENS eison a aaa 17 DICAM E ere RE 18 2007 5 11 2 Introduction Thank you for purchasing the SUNRUNNER APT Power Assist Folding Electric Bicycle hereinafter referred to as E Bike tactfully designed and manufactured by PIHSIANG MACHINERY MFG CO LTD hereinafter referred to as PMMC The user s manual contains all kinds of important information concerning the operation and the safe use of your E Bike Please read this manual carefully and thoroughly before riding your E Bike and make sure that you have learned all the instructions of the E Bike If you have any queries about the spare parts for the maintenance or any other concerns of your E Bike please contact your authorized dealer for assistance Features 1 Saddle ON I OFF ON II Switch Main Switch Battery Gauge Handle LiFePO Battery Case w Light Controller w Light T
7. en released to restore to its disengaged position Power assist function Battery case with an empty As the last battery indicator light discontinued when charge start flashing then the battery case riding must be recharged as soon as possible or the power assist will be discontinued after approximately 2KM riding further Poor traveling range Frequent riding on Decrease chance to ride on gradients poor tire gradients to check if a longer range pressure battery case with lis acquired fill up tire pressure to insufficient charge or 50 PSI fully charge the battery battery aging etc daily after use or replace a new battery case etc sound noise existed on wheels or motor wheels and motor X Note Must use the genuine SUNRUNNER charger dedicated for C LiFePO Battery Case to be charged X Please contact your authorized dealer if the above solution has been checked and the problem is still existed 2007 5 11 16 Specification onon om 1385 wmn m Dimension Handlebar ae 1050 Wheels Center saree mm OoOo Reference Range on the level ground without wind Set to the 1 85Kg The output power assist from the stage of a rider s 28Km 34Km controller can be set up from 1 10 power assist weight stage for riders Power Assist Driving Wheel Front Wheel Drive Hub Motor Model Brush Motor with reduction gear 24 V Type Dedicated for C LiFePO Battery Charger Charging Time 25 min 2 5 hrs 1
8. er once you ride it Before you depressing pedal on the E Bike please ensure ahead of the road is clear 10 Adjust the height of the saddle to fit your body size Take heed of the maximum height markings on the post of the saddle Your authorized dealer will give you assistance if requested 11 Refer to the instruction sheet of the SHIMANO Inter 3 Gear to switch 3 stages of gears for a more comfortable riding at different slopes 12 Always consult your doctor for advice on your physical condition and follow your country s traffic rules while riding 13 Make sure that your dress and shoelaces must be secured from involvement to moving parts of the E Bike while riding 2007 5 11 4 User Guidance 10 stages power assist output adjustment 1 Depress the pedal against a wall Do not grab the front or rear brake lever while depressing the pedal 2 Then press the main switch to either left 1 or right II position while depressing the pedal 3 After 10 seconds the light of controller will flash as below The 1 flash means the 1 stage The 2 flash means the 2 stage The 10 flash means the max the 10 stage output from the controller Release the pedal at once after selecting your desired stage Note X It s recommended to set up at the 1 stage if riding on level ground frequently to save battery charge X It has been set up at the 10 stage for the default setting on your E Bike
9. ire Spoke 9 Rim 10 Pedal 11 Kickstand 12 Hub Motor Assembly 13 Chainwheel Assembly 14 Gear shift Handle 15 Derailleur Shimano Inter 3 Gear 3 Po ey Eas I E X SUNRUNNER is a registered trademark of the PMMC products X APT is registered for Advanced Power Technologies developed and owned by PMMC 2007 5 11 3 Safety Warnings 1 Do not operate the E Bike before reading this user manual thoroughly 2 Do not disassemble the battery case and modify the unit without PMMC written approval or your warranty will be void and you will be responsible for the modification 3 Front basket is optional and the maximum load for the basket is 2 kgs 4 Check the tire pressure of front and rear wheel to be around 50PSI or 3 5bar before riding 5 Make sure that the battery has been fully charged before use and remove the charger after fully charged 6 Check all electrical connections and mechanical parts are securely locked and fastened before using your E Bike and check all cables connector plugs and sockets must be dry and undamaged 7 The E Bike is not recommended for competition stunt any aggressive or off road riding 8 The performance and mileage of the unit will be varied with the battery condition temperature terrain wind speed tire pressure rider weight and the maintenance etc 9 The E Bike is able to sense your feet s force on the pedal to provide you the assist pow
10. ling is stopped Check Battery Check if the battery case fits into the battery holder firmly and the LED Light of the battery case is lightened up when the main switch is on at the II position Check if the battery is fully charged before use Check Motor and Control System Must check the motor and control system are performed well General Inspection Check if any of brake shoes with excess worn out should be replaced Check if the braking function is performed well Check if the front and rear wheels are performed smoothly Check if all connectors on E Bike are firmly secured without any damage If you have any questions after checking please refer to the solutions for trouble shooting page 16 or contact your authorized dealer for inspection and maintenance Cautions for Riding Always follow the county s traffic rules while riding Check the battery gauge if the charge is sufficient to keep the power assist for your riding Do not keep riding your E Bike if any problem is occurred and then refer to the solutions for trouble shooting page 16 or contact your authorized dealer for further inspection and maintenance Ensure to use the spare parts supplied by PMMC for replacement Other Keys to Lifespan The lifetime of your E Bike will be adversely affected by exposures to aggressive road dirt rain waters or salt soray To package your E Bike including the battery case with a good protection for
11. r port of battery case Operating Instruction 1 Must assure the input voltage is between 100V 240V 2 Must assure the battery to be charged is a LiFePO Lithium Iron Phosphate Based Battery Pack supplied by PMMC 3 Make sure the power cord battery cable and battery terminals are in good condition 4 Make sure the connecting battery rating is the same as the charger output voltage 24V 5 While charging LED will display a RED light When the light turns GREEN the battery is fully charged LED Indication 1 LED GREEN Power On when not connected to the batteries 2 LED RED Charging 3 LED GREEN Fully Charged when connected to the batteries Trouble Shooting 1 If the LED light is OFF all the time while charging Check if the power connections are in good condition If the LED light is still off all the time while charging the battery charger may be malfunctioning Please consult your authorized dealer for further assistance 2 If the LED light does not switch from GREEN to RED when the charging process begins Check if the connection of the battery polarity is correct Check if the connection between charger plug and charging port of the battery is correct Check if the battery case is already fully charged Check if the battery is functioned properly 3 The charging time continues for a long duration Irregular Check if the battery is out of order or aged 4 The battery overheats 2
12. roller and battery case utilizes the 1W Warm White LED Light which is green energy and provides moderate light in the dark e The battery gauge with 4 battery level indicators Warm White LED Light precisely indicate the remaining charge of the of Battery Case battery As the last battery indicator light starts flashing the rider can continue to ride the E Bike for approx 2KM further e Swivel the cover from the charging port to charge the battery After charged fully must swivel the cover back to the charging port to prevent water and dust from getting into the socket e The battery case is not allowed to be disassembled and should be prevented from dipping into water and exposing to fire e Portable battery case with 1 4kg weight around can be placed in a carrying bag attached with each E Bike and may be used for individual lightening system same as a flashlight device With different capacity of the battery the warm white LED light can be lasted for 3 6 days e The threading hole is available underneath the battery i i case for the connection to other devices such as Battery Case mounted camera s stand as shown on camera s stand 2007 5 11 11 Steps to fold the E Bike Refer to the instruction for Dismounting Battery Case to remove the battery case m Loosen the clamp lever to remove the saddle Note Keep the battery case and the saddle in a safe place after removed from the E Bike
13. transportation and to store your E Bike indoors when not in use are essential to prolong the lifespan of product 2007 5 11 7 Battery and Charging Dismounting Battery Case Before sliding out the battery case make sure the battery holder latch is at the position as shown 2 Switch the key to horizontal flat position Depress the key to release the lock and use the other hand to push the battery case out from the battery holder 3 Remove the battery case Mounting Battery Case 1 Please secure the battery case holder with one hand and slide the battery case onto the rail all the way down to lock the battery case as shown Note If the battery case can be removed without depressing the key this means that the battery case has not been properly locked Then please repeat the above procedures again 2 The battery case will be locked and can t be removed when the key is in the vertical position 2007 5 11 8 Battery and Charging Steps to charge the Battery 1 Switch your E Bike off on the main switch of Power Plug Charger Plug battery case 2 Dismount the battery case and then place it ata ventilated place to be charging 3 Swivel the charging port cover of battery case and then connect the charger plug of the charger 4 Plug the power plug of the charger into secure power source to start charging battery Note Ensure that the charger plug is dry and securely connected to the charge
14. uard Note Follow the same steps while installing the Mudguard on a new unit Pull the trigger of the pedal and unfold the pedal simultaneously Repeat the same steps on the other side of the pedal a A Install the saddle and adjust Refer to the instruction for Mounting it to the desired height and Battery Case to be mounted then tighten the clamp lever Note For your safety do not set the saddle height exceeding the bottom line on the seat post The unfolding steps are completed 2007 5 11 15 Trouble shooting PROBLEM POSSIBLE CAUSE SOLUTION Battery case with a Battery case has not been Follow the instruction to dismount loosening issue such _ totally locked onto the then mount battery case again to as battery case could be battery holder firmly check if battery case can not be removed when the key removed without depressing the on battery case is not key depressed Battery gauge LEDs with Battery case has a low Check if battery case has been no display when power icharge or a loosening issue fully charged before use To check on the solution as above if the battery case has a loosening issue Power assist fails to Controller may go to sleep Switch power off and then back on perform its intended mode to preserve battery ito remove from sleep function when pedaling charge after being idle for Check handbrakes are totally few minutes disengaged when the levers have Or one of handbrakes fails be
Download Pdf Manuals
Related Search