Key Pro TPX Generator User Manual
Contents
1. Q x elettronica TPX GENERATOR USER MANUAL ne elettron ica el Emme KEY pro N2 9 ERIFY RAM READ Bt pros Es e TiEmme elettronica Summary MRO 3 1 1 A E o 3 1 2 doo a A 3 1 3 TECNICA OSTA rata ia at 3 1 4 IMEEKRAMONTON rt ba 5 1 4 1 PE MOde a Inle ROIN T FPHPRREEpRp Ry R FT y 6 1 4 2 MEMO Caral a se TTT ETRTTTTTTTRTTRERTRETT TR y L 6 1 5 AE DA PTT 7 1 6 FOS c o E 1 7 TA 9 1 8 TG P 11 1 9 Is nn 14 o E Po A 15 2 e ES do AA eE EE EP o 16 2 1 e EWS Mista ClO Mera ia iaa 16 2 2 A A 17 23 CrEdhO pO a PP IIO sse NEA DO E E Kvon E 17 2 4 Crean ota SPI TIO sasa A E E E ra o 18 2 4 1 Converting a file parameters TIM sssss ssssssscsssssscsssssssesqsusssseqnassssqsassesessss 18 2 4 2 Extracting the parameter set from a format tpp file sesssssssssesesssssssena 19 2 4 3 Firmware upgrade of Key P O ria 19 l TiEmme elettronica KEY PRO 1 1 FEATURES This guidebook provides the whole information required for the right utilization of the device Key Pro combined to the products of TiEmme elettronica Key pro is a device developed for the updating of all the produc2. e Open the panel for selecting the connection mode F Connection Mode Serial Port GSM Modem TERAP Connect to e Control board f USB Programmer COM Port Selection COM Part COM10 E Search Fig 21 Select Connect to control board and press Search the system starts searching the device between the COM ports system available and automatically connects At connection occurred it displays a green LED on the bottom left in the status bar of the software System Evolution To end the connection it is necessary to use the Disconnect button F Connection Mode Serial Port GSM Modem TEFAIP f Control board f USB Programmer COM Port Selection COM Port COMO Fig 22 14 TiEmme elettronica 1 10 SETTINGS Through the SETTINGS menu you can set the date and time and adjusting the brightness of the display From the Main screen select the SETTINGS button to access the two submenus 12 00 SETTINGS TiEmme elettronica KEY Pro PROGRAM VERIFY Fig 23 Select item DISPLAY LIGHT to adjust the brightness of the display Menu Display Light Time and date X Fig 24 Use the and buttons to set the desired value To apply the changes you made use the OK button To cancel the operation use the X button Menu Display Light 92 Min 10 Val 92 Max 100 ok Fig 25 15 TiEmme elettronica Select the item TIME AND DATE to set t
3. the SD memory With the BROWSE button it access the file selection screen Select File MB100 MB250 SY400 FSYSI01000003 FSYSI01000004 A OK V Fig 11 This screen displays all the files and folders on the SD card Here it is possible to browse its contents using the navigation arrows Folders are identified by the symbol L3 while usable files for programming the device are identified with the symbol Selected the desired file the device proposes the screen with name and any notes entered by the user while creating Fig 10 Through the START button it starts the process of reading and leads to the following screen Selected file for read MB100 Idro Easy Tech One Please do following operation Connect target To start then press MAINS for mains power mode OR BATTERY for battery power mode BATTERY CANCEL Fig 12 10 TiEmme elettronica On the screen are displayed the operations to perform and it is also required the mode with which comes powered the product during the reading Choose MAINS if the product is connected to the mains choose BATTERY to use the internal battery of the device After choosing the power source begins the reading process Reading to 0014 11 21 1459 9590 CANCEL Fig 13 After the procedure displays a summary screen with the result of the operation Result for read Operation summary Operation completed No errors fou
4. card The greater is the number of files and folders in the root of the memory card the more time browsing and access required from the device TiEmme elettronica 1 4 1 PC MODE FUNCTION The PC Mode function takes disabling user touch interface and activation of the profile of Mass Storage The device is identified by the PC operating system as a storage device allowing all the typical file operations manager copy rename delete files and so on The device will appear in the PC resources identified as a removable disk To activate PC Mode it is necessary to use the included USB cable and connect the device to a PC USB port On the device screen the activation button will appear Fig 1 and the screen Fig 2 at activated action 12 00 SETTINGS TiEmme elettronica KEY Pro PC MODE PROGRAM VERIFY Fig 1 PC MODE Fig 2 To quit the PC Mode and restore normal operability proceed as follows a Remove the device following the safe removal procedure of the Windows Hardware b Disconnect the USB cable and wait until the device turns off c Turn on the device after shutdown 1 4 2 MEMORY GARD READER To access the contents of the removable memory it is possible to use a memory card reader compatible with the format micro SD HC Remove the card from the right slot and insert it into the player The memory will be identified as a mass storage device and the content will be accessible from the Windows file manager This m
5. evel o Preview of the features of the file Notes Product ID Product Date Release Version o Selection of the power source o Report at the end of the operation READ It allows to read parameters from the control board based on a structure file TPR chosen by the user The main functions are o Reading parameters from the control board with rescue in the internal memory o Identity verification of the product for the validation of the structure parameters o Report at the end of the transaction VERIFY Check the parameters inside the control board based on a structure TPR ot TPP reference USE WITH SYSTEM EVOLUTION Combined with the software System Evolution it acts as a converter from USB COM virtual to RS232 serial with the same functionality of the product USB Programmer 1 4 INTERNAL MEMORY The device has an internal removable memory based on a card type Micro SD HC Only memory cards formatted with the FAT32 file system are supported It is possible to turn on and then to use the programmer only with a SD card inserted into the right slot lt is possible to organize the contents of memory in a structure to files and folders To access the content stored in the device proceed as follows e Using the function PC Mode e Using a card reader memory to access to the SD card N B for maximum performance in terms of speed navigation and scrolling files you may want to organize your files in a single folder in the root of the SD
6. he date and time The format data used is DD MM YYYY Menu Display Light Time and date X Fig 26 Use the and buttons to adjust the date and time To apply the changes you made using the OK button To cancel the operation using the X button Set Timedate gt 8 45 2 6 2014 Fig 27 2 TPX GENERATOR The software TPX Generator is the tool that allows the creation of files in TPP format and the conversion of program TIM file in TPR file The main functions available to the user are e Create a TPP file that contains FW parameters and other resources e Create a TPR file starting from a parameter TIM file e Create a TPR file starting from a TPP file holding parameters e Update of the device s FW 2 1 SOFTWARE INSTALLATION To install the software launch the setup exe file and follow the directions provided by the wizard The setup also installs the drivers necessary for the proper operation of the device At the end of the installation the TiEmme elettronica grouping will be created between the available programs or if already present updated with the inclusion of the new software To use the software it is possible to double click the icon on the desktop or to click the exe present on Programs gt TiEmme elettronica gt TPxGenerator exe 16 TiEmme elettronica 2 2 SOFTWARE INTERFACE The software interface is organized into the following main sections 1 Platform for the c
7. hoice of the product platform 2 Add application FW for selecting source Firmware files type of TFW or TPP 3 Add Program for selecting the source from which to import the set parameters Database System2000 mdb System evolution TIM file file TPR and file TPP 4 Add other resources for selecting additional resources that differ from the set of parameters Images for Easy touch keyboard etc 5 User Notes user editable text field in which it is possible to enter the comments present in the imported FW o TiEmme Program package Parameter package preparator V 1 0 0 11 Fie Programmer E F 2 Add Application FW 7 3 Add program Fig 28 2 3 CREATION OF A TPP FILE The format TPP allows the distribution in a single file of FW of parameters and other eventual resources of a product Cannot be created TPP files containing only FW or parameters resources but both elements must be present The files TPP containing only FW can be created and distributed only by TiEmme elettronica The creation process is divided into four main steps 1 Choice of product platform on which to operate via the drop down menu of Section 1 2 Apply the flag check to activate the section 2 Add application FW and choose the FW source file using the Browse button ln the event that within the FW there are comments the software proposes theirs import These comments will appear in the User Notes 17 TiEmme elettr
8. lected file for verify B100 Idro Easy Tech One Please do following operation Connect target To start then press MAINS for mains power mode OR BATTERY for battery power mode Fig 18 On the screen are displayed the operations to perform and it is also required the mode with which comes powered the product during the verify Choose MAINS if the product is connected to the mains choose BATTERY to use the internal battery of the device After choosing the power source begins the verifying process Executing 9590 A CANCEL Fig 19 After the procedure displays a summary screen with the result of the operation Result for verify Operation summary Operation completed No errors found DONE Fig 20 13 TiEmme elettronica 1 9 USE WITH SYSTEM EVOLUTION The device similarly to what happens with the product USB Programmer can be used for connecting to the control board through the Software System evolution In this case the device performs the function of converter from the USB COM virtual port to RS232 serial To connect the System software evolution to the control board proceed as follows e Connect the device Key Pro to PC with the USB cable provided Do not activate the PC Mode e Connect the device Key Pro to the control board via the RS232 communication port and the cable with RJ11 plug supplied e Turn on the control board and launch the software System Evolution
9. nd DONE Fig 14 1 8 VERIFY The VERIFY function allows the comparison between the set of parameters in a control board and those of a program in file format TPR The file TPR used must have a parameter structure compatible with the control board in question From the main screen select the VERIFY button to access the verification function parameters 11 TiEmme elettronica 12 00 SETTINGS TiEmme elettronica KEY Pro PROGRAM VERIFY Fig 15 The device offers the ultimate file TPR selected as structure set benchmarks Selected file for verify MB100 Idro Easy Tech One Note utente START BROWSE CANCEL Fig 16 Then it is possible to read or choose a different reference file from those available in the SD memory With the BROWSE button it access the file selection screen Select File MB100 7 FMB250 SY400 FSYSI01000003 l FSYSI01000004 A OK V Fig 17 This screen displays all the files and folders on the SD card Here it is possible to browse its contents using the navigation arrows Folders are identified by the symbol L3 while usable files for programming the device are identified with the symbol Selected the desired file the device proposes the screen with name and any notes entered by the user while creating Fig 10 Through the START button it starts the process of verify and leads to the following screen 12 TiEmme elettronica Se
10. ode is preferable when it is necessary to transfer within the device a considerable amount of data For the removal of the board follow the safe removal procedure of the Windows Hardware TiEmme elettronica 1 5 INTERNAL BATTERY The device is equipped with an internal lithium battery that lasts for 12 hours with the device on and about 30 days in Standby mode The battery in addition to the normal operation of the device can be used for feeding the products during the stages of programming lt is possible to recharge the battery by connecting the device to a USB port of a PC or to the mains 230V via the supplied power adapter and USB cable 1 6 PROGRAM With the function Program it is possible to program firmware of the TiEmme elettronica products To access this feature use the button PROGRAM directly from the Main screen 12 00 SETTINGS TiEmme elettronica KEY Pro PROGRAM VERIFY Fig 3 In the next screen the device remembers the last selected file Selected file for program A FSYSI01000003 SY100 Air FSYSI01000003 SY100 IDRO EasyTech STD Product ID SYEVO0000368 Release Date 12 02 14 Release Version 0 5 START BROWSE CANCEL Fig 4 For each file it comes displayed the following information e File name e Product ID Product identity e Release Date Date of file review e Release Version Number of review e Notes Any notes you entered during the review or file creation It is possible to p
11. on TiEmme Program package Parameter package preparator V 1 0 0 11 File Programmer 1 Platform SY100 2 Add Application FW v 3 Add program 9 Program from tim or System2000 Product SY325 Standard per Caldaie Idro e ad Aria Program Parametri per Caldaia Idro Air Program from existing tpr or tpp file User notes Fig 29 18 TiEmme elettronica 2 4 2 EXTRACTING THE PARAMETER SET FROM A FORMAT TPP FILE 1 Apply the flag check to activate the only section 3 Add program 2 Choose the type of file source parameters to use TPP TPR Use the Database button for the selection of the file 3 Editor enter any notes and comments that will be displayed in the device under User Notes 4 Save the final format TPR file using the Save button TiEmme Program package Parameter package preparator V 1 0 0 11 File Programmer 1 Platform SY100 E 2 Add Application FW Y 3 Add program Program from tim or System2000 9 Program from existing tpr or tpp file Selected file si Browse User notes Fig 30 2 4 3 FIRMWARE UPGRADE OF KEY PRO To update FW device from the Programmer menu choose Key Pro Firmware Update Through the dialog box that appears select the file format TPP for upgrade lf the FW updating has been successful is incremented revision numbers displayed on the main screen 19
12. onica 3 Apply the flag check to activate the section 3 Add program Choose the file type to be used between source parameters TIM MDB OR TPP TPR In the first case use the Database button for the file selection The software displays the products and programs in the file respectively in the drop down menu Product and Program If the source file consists TPR or TPP use the Browse button to select the file 4 If necessary apply the flag check to activate the section 4 Add other resources and use the Browse button to select the file 5 Editor enter any notes and commenis that will be displayed in the device under User Notes 6 Save the final format TPP file using the Save button 2 4 CREATION OF A TPR FILE The TPR files contain only one set of parameters encrypted The creation of a TPR file can be done in the following ways e Converting a file parameters TIM e Extraction the parameter set from a format TPP file 2 4 1 CONVERTING A FILE PARAMETERS TIM 1 Apply the flag check to activate the only section 3 Add program 2 Choose the type of file source parameters to use TIM System2000 Use the Database button for the selection of the file The software displays the products and programs in the file respectively in the drop down menu Product and Program 3 Edit or enter any notes and comments that will be displayed in the device under User Notes 4 Save the final format TPR file using the Save butt
13. onica Result for program Operation summary Operation completed No errors found DONE Fig 8 Operation completed The process is completed with no errors The FW selected is not compatible with the Operation ERROR Incompatible target product to be programmed l There were errors during programming eg PARINI CE WEGO Disconnection of the cable etc Operation canceled by user Procedure aborted by user Operation ERROR verify error Error in the verify procedure 1 7 READ The READ function allows you to capture the set of parameters stored in a control card and save them to the root of the removable memory as a file TPR To read and create files the device requires a structure set benchmarks A valid structure is a program in TPR format usable with the control board in question The TPR file created is structured as follows OOYY MM DD hhmm TPR e YY current year e MM current month e DD current day e hhmm hours and minutes at the starting process From the Main screen select the READ button to access the function of reading parameters 12 00 SETTINGS TiEmme elettronica KEY Pro PROGRAM VERIFY Fig 9 TiEmme elettronica The device offers the ultimate file TPR selected as structure set benchmarks Selected file for read MB100 Idro Easy Tech One Note utente START BROWSE CANCEL Fig 10 Then it is possible to read or choose a different reference file from those available in
14. protocol ModBUS e Port for connecting and updating the radio terminal 2Ways2 Micro USB B Port to use with the Micro USB cable supplied to connect the device to the PC and to the power supply network Maso Slot for internal memory card type micro SD Supported file TPP TiEmme Product Package Holding FW and resources File encrypted with 64 bit key There are inside many additional resources such as graphics for Easy Touch keyboard The resources are classifiable like support information to the product Images and parameters set in TiEmme elettronica generally fall between the following TiEmme elettronica TPR TiEmme Product Parameter Holding only resources of set parameters type and it is structurally identic to the file TPP not having within the FW File encrypted with 64 bit key The file TPR can be created with the software Try generator Firmware file of TiEmme elettronica products Available functions PC MODE Mode that disables the user touch interface and the activation profile of Mass Storage The device is identified by the operating system of the PC as an external storage device allowing all the typical file operations manager The PC mode is activated by the user when the programmer is connected to the PC via USB PROGRAM This mode allows to select files in the internal micro SD memory card and sent them to programming The main functions are o Selecting files via navigation system folders multi l
15. roceed with the programming or choosing a different file from those stored in the SD memory With the button BROWSE it is possible to access to the file selection screen TiEmme elettronica Select File MB100 MB250 SY400 7 FSYSI01000003 x FSYSI01000004 x A OK V Fig 5 This screen displays all the files and folders on the SD card Here it is possible to browse its contents using the navigation arrows Folders are identified by the symbol L3 while usable files for programming the device are identified with the symbol Selected the desired file the device proposes the screen with his features Rif Fig 3 Selecting START button it starts the programming procedure Selected file for program FSYSI01000003 SY100 Air Please do following operation Connect target To start then press MAINS for mains power mode OR BATTERY for battery power mode BATTERY CANCEL Fig 6 On the screen are displayed the operations to perform and it is also required the mode with which comes powered the product to program Choose MAINS if the product is connected to the mains choose BATTERY to use the internal battery of the device After choosing the source of alimentation it starts the process of updating Erasig Programming 95 95 A A CANCEL CANCEL Fig 7 At the end of the procedure it displays a summary screen with the result of the operation TiEmme elettr
16. ts of TiEemme elettronica and in particular for the updating of the firmware of the parameters set and eventually additional resources The main functionalities are Programming FW and updating parameters set through the connection to serial ports RS485 and RS232 Internal SD card for files storage Firmware and programs Internal lithium battery rechargeable Completely touch interface Graphical navigation menu Functions of verify and reading of the parameters set Storage and browsing structure to files and folders PC connection for charging battery and accessing internal memory 1 2 PRODUCT COMPOSITION The product is delivered with the following articles Device Key Pro 1 Communication cable with RJ45 and RJ11 plug 1 Communication cable with RJ11 and RJ11 plug 1 USB cable with Micro USB type B connector 1 power supply wall with USB type A connection 1 Micro SD Card 1 3 TECHNICAL DETAILS System requirements Compatible with operating systems 32 and 64 bits It can be installed on Windows XP Vista 7 8 It requires NET framework 2 0 or higher TiEmme elettronica Size and dimensions Top view Ports and conections RS485 Connection port with RJ45 plug for updating keyboards cards lambda and products that use the ModBUS protocol for communication Serial port connection with RJ11 plug for updating the control cards and all the devices that do not use the communication
Download Pdf Manuals
Related Search