Home

Ditec DAB105 User manual

1. Elbow switch 11 see page Radar 12 see page 9 Wireless transmitters not illustrated Access control not illustrated Door stop not illustrated Safety accessories Even though the Ditec DAB105 is installed to comply with all applicable safety regula tions it is possible to enhance safety comfort with the following add ons please con tact your local ENTREMATIC representative for detailed description Safety sensors 13 see page 9 Finger protection 9 see page 9 Troubleshooting What s wrong Remedies The door does not open The motor does not start Change the setting of the program selector See page 6 Check that there are no objects in the detection zone if a sen sor is fitted Check the mains switch and fuse in the building The motor starts but door s Unlock the mechanical locks willnotopen Check that nothing is jammed beneath the door The door does not close Change the setting of the program selector See page 4 Check that there are no objects in the detection zone if a sen sor is fitted Check that nothing is jammed beneath the door The door opens and closes Check that there are no moving objects within 1 1 5 m 39 continuously 59 from the door if an automatic activation unit is fitted If the problem continues please contact your ENTREMATIC representative IP2173EN 2013 06 05 IP2173EN 2013 06 05 Declaration of conformity We Entrematic Group AB Lodju
2. 06 05 Regular safety checks To help you fulfil the national international requirements and to avoid malfunction and risk for injuries we have provided the following checklist Do not use if repair or adjustment is necessary Disconnect supply 14 when cleaning or other maintenance is to be carried out If problems Daily Action occurs Activate your operator and check visually fastening of e operator 1 e arm system 2 e cables 3 programme selectors 4 hinges 5 door and glass 6 e Also inspect your operator and check visually for sharp edges on the door leaf and door frame if any 7 condition of door seals 8 finger protection 9 and finally that the complete door runs properly and closes slowly in a smooth way Set the programme selector to OFF and check that the operator and electrome chanical lock if fitted work together Also check that the lock 10 really secures the door Activate the manual activation units 11 if any and walk towards the door Check that the door has opened appropriately while you pass the entrance exit Then proceed with the automatic activation units 12 in the same way Check the non monitored safety sensors 13 if any by standing in the swing path and activate the operator The door must not hit you when opening nor when closing If you are unsure of which type of sensor you have please contact your ENTRE MATIC representative Escape doors Set the programme selector i
3. _Ditec ENTREMATIC Ditec DAB105 IP2173EN iF mm i Instruction for safe operation e Failure to observe the information in the user manual may re sult in personal injury or damage to equipment To reduce the risk of injury to persons use this operator with single or double pedestrian swinging or folding doors only Do not use the equipment if repair or adjustment is necessary Disconnect supply when cleaning or other maintenance is to be carried out e The operator can be used by children age 8 and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction by a person responsible for their sa fety concerning safe operator use and the possible hazards involved This does not however prevent those persons to use the door where the operator is installed Cleaning and user maintenance shall not be made by children without supervision e Do not let children climb on or play with the door or the fixed remote controls All the rights concerning this material are the exclusive property of Entrematic Group AB Although the contents of this publication have been drawn up with the greatest care Entrematic Group AB cannot be held responsible in any way for any damage caused by mistakes or omissions in this publication We reserve the right to make changes without prior notice Copying scanning and changing in any way are ex
4. age Check that all required signage is applied and intact Mandatory indicates that the signage is required by Euro 200 1100 mm 800 mm pean directives and equivalent national legislation outside the European Union Ref 6 Contact your ENTREMATIC service representative For contact information see last page Description Product label Mandatory Supervision of child Mandatory if applicable Apply to both side of the door To be placed on entrances where risk analysis shows use by children elderly and disabled Operator designed for disabled people Raccomended if applicable applied to both sides of the door Automatic door Only mandatory in GB Keep clear Only mandatory in GB No entry Identifying one way traffic Mandatory in GB and US If applicable Emergency break out Mandatory if approved for escape route Door sticker Mandatory if applicable to highlight the presence of the glass applied to all glass sections that are moving Activation by disabled people Recommended if applicable General accessories Your Ditec DAB105 can be further improved with the following add ons please contact your local ENTREMATIC Group company for detailed description e Position switch 4 see page 9 e Electrical lock 10 see page 9 Key switch 11 see page 9
5. atteries containing materials which are hazardous to the environment Discon nect power before removing electronics and battery and make sure it is disposed of properly according to local regulations how and where as was done done with the packaging material Product liability According to regulations the following are the responsibility of the owner or caretaker of the equipment e that the equipment operates correctly so that it gives sufficient protection in regard o safety and health e that the equipment is operated and regularly maintained inspected and serviced by someone with documented competence in the equipment and in applicable re gulations e that a journal is kept of inspection maintenance and service records including the provider e that inspection covers the emergency opening function when applicable e that the closing force is appropriate for the door size on fire approved door systems when applicable Service Regular inspections by a trained and qualified person and the frequency of service occasions should at minimum be made according to national regulations or industry standard in the absence of a national regulation This is especially important when the installation concerns a fire approved door or a door with an emergency opening function To extend the life of your investment and ensure safe and reliable operation of the door we recommend a minimum of 2 visits per year or more depending on usage an
6. d operating conditions Environmental aspects shall also be considered Intended use The Ditec DAB105 is an automatic swing door operator developed to make life easier or everyone who can benefit from automatic doors The Ditec DAB105 is a low energy as well as a full power operator using a DC motor and a gear reduction system to drive an arm system which opens the door t is to be installed indoors where it is suitable for almost all types of external and internal swing doors This widely used operator can be found on applications ranging from handicappedac cess in private homes to high traffic retail operations For installation and maintenance see Installation and Service manual IP2159 Save these instructions for future reference IP2173EN 2013 06 05 IP2173EN 2013 06 05 How the Ditec DAB105 works The swing door operator Ditec DAB105 uses a DC motor and a gear reduction system to drive an arm system which opens the door Closing power is provided by a motor and ac ock spring A highly sophisticated electronic control unit uses a motor encoder and a microprocessor to control the door s movement To activate the operator you can use a manual activator elbow switch or an automatic act the ivator radar device It is also possible where local standards allow to activate operator by just pushing the door if Push amp Go is selected After the door has been activated it will open and stay open
7. for a specified Hold Open Time HOT When the HOT has elapsed the door will close The Ditec DAB105 can be set in three or four different modes depending on program me selector type see table below In fully manual use or in case of a power failure the Ditec DAB105 acts as a normal door closer Position Function A AUTO The door can be opened with the inner and outer manual and or o mm Normal automatic activators tv C position The electric strike if fitted is open OFF The door is closed The door cannot be opened with inner and m outer activation units The door is locked if an electromechanical J C locking device has been fitted The door can be opened with a key switch if fitted OPEN The door is held permanently open by the motor J C A EXIT Passage from inside only The door is normally locked if an elec er tromechanical locking device has been fitted The door can only be opened with the inner activation unit and with a key switch if fitted Technical specification Manufacturer Address Type Mains power supply Power consumption Class of protection Approvals Entrematic Group AB Lodjursgatan 10 SE 261 44 Landskrona Sweden Ditec DAB105 100 240 V AC 10 15 50 60 Hz max 75 W IP20 Third party approvals from established certification organizations valid for safety in use see Declaration of Conformity IP2173EN 2013 06 05 IP2173EN 2013
8. n AUTO mode Push the door manually in escape direction and make sure that no object or function will prevent the door from opening Also make sure the escape route is free for use Fire doors Let the door close after an impulse en suring nothing prevents the door from closing and locking if regulations re quire it DO 8G OG regularly by trained person By law these tests must be nel performed take appropriate measures Contact your ENTREMATIC service representative For contact information see last page Function and visual inspection Clea The bes soft clot enamel ning t way to remove dust and dirt from the Ditec DAB105 is to use water and a h or a sponge A gentle detergent may be used To maintain the quality of the ayer the surfaces should be cleaned once four months period The cleaning should be documented To avoid damages to the profiles the brushes weather strip ping mu Do no sensit Do no may b e Do no Dono st be vacuum cleaned weekly expose windows doors or profiles to alkalis Both aluminium and glass are ive to alkalis t clean with high pressure water Operator programme selector and sensor e damaged and water may enter the profiles use polishing detergent scrub with materials like Scotch brite as this will cause mechanical damage IP2173EN 2013 06 05 IP2173EN 2013 06 05 Sign
9. pressly forbidden unless authorised in writing by Entrematic Group AB IP2173EN 2013 06 05 IP2173EN 2013 06 05 Electronic equipment reception interference The equipment complies with the European EMC directive US market FCC Part 15 provided installed according to Installation and Service manual The equipment may generate and use radio frequency energy and if not installed and used properly it may cause interference to radio television reception or other radio frequency type systems If other equipment does not fully comply with immunity requirements interference may occur However there is no guarantee that interference will not occur in a particular installa tion If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient the receiving antenna e Relocate the receiver with respect to the equipment e Move the receiver away from the equipment e Plug the receiver into a different outlet so that equipment and receiver are on diffe rent branch circuits e Check that protective earth PE is connected If necessary the user should consult the dealer or an experienced electronic techni cian for additional suggestions Environmental requirements Entrematic Group products are equipped with electronics and may also be equipped with b
10. rsgatan 10 SE 261 44 Landskrona Sweden declare under our sole responsibility that the type of equipment with name serial number Ditec DAB105 Complies with the following directives 2004 108 EC ElectroMagnetic Compatibility Directive EMCD 2006 42 EC Machinery Directive MD Harmonized European standards which have been applied EN 60335 1 EN 16005 EN 61000 6 2 EN 61000 6 3 EN ISO 13849 1 Other standards or technical specifications which have been applied EN60335 2 103 DIN 18650 1 2 FCC 47 CFR Part 15 B UL 325 EC type examination or certificate issued by a notified or competent body for full address please contact Entrematic Sweden AB concerning the equipment The manufacturing process ensures the compliance of the equipment with the technical file The manufacturing process is regularly accessed by 3rd party Compilation of technical file Johnny Persson E mail johnny persson dentrematic com Entrematic Group AB Lodjursgatan 10 SE 261 44 Landskrona Sweden Place Date Signature Position Landskrona 2013 04 17 Johnny Persson Product Safety amp Liability Manager IP2173EN 2013 06 05 Entrematic Italy S p A Via Mons Banfi 3 e 21042 Caronno P lla VA Italy Tel 39 02 963911 Fax 39 02 9650314 www ditecentrematic com ICIM ISO 9001 Cert n 0957 Ditec ENTRE MATIC

Ditec DAB105 User manual

Contents

Download Pdf Manuals

Related Search

Related Contents