MSII 6K 4U English neutral user manual
Contents
1. JAGUAR LEOPARD 6 20 KVA Sinercom S r l Headquarter Via Alessandro Dudan 9 00143 Rome RM Italy tel 39 06 79800323 fax 39 06 79814644 Factory Via Cascina Secchi 247 4b 24040 Isso BG Italy tel 39 0363 938231 fax 39 0363 998235 Commercial office tel 39 02 303126850 828 Fax 39 02 70051026 USER MANUAL Please comply with all warnings and operating instructions in this manual and on the unit strictly Save this manual properly Do not operate this unit before reading through all safety information and operating instructions carefully 1 IMPORTANT SAFETY INSTRUCTION 1 Safety and EMC instructions Please read carefully the following user manual and the safety instructions before installing the unit or using the unit 1 1 Installation mCondensation may occur if the UPS is moved directly from a cold to a warm environment The UPS must be absolutely dry before being installed Please allow an acclimatization time of at least two hours m Do not install the UPS near water or in damp environment m Do not install the UPS where it would be exposed to direct sunlight or near heat m Do not block ventilation openings in the UPS s housing m Do not connect appliances or items of equipment which would overload the UPS e g laser printers etc to the UPS output m Place cables in such a way that no one can step on or trip over them mUPS has provided earthed terminal in the final installed system confi2. 6000 10000 Input Ground Output Ground Input Neutral Output Neutral Input Line Wire A Output Line Input Line Wire B Input Line Wire Input and Output Terminal Block wiring diagram of LEOPARD 10000 20000 5 3 Operating procedure for connecting the long backup time model UPS with the external battery 1 The nominal DC voltage of external battery pack is 192VDC Each battery pack consists of 16 pieces of 12V maintenance free batteries in series To achieve longer backup time it is possible to connect multi battery packs but the principle of same voltage same type should be strictly followed 2 For JAGUAR 6000XL 10000XL and LEOPARD 10000XL 15000XL 20000XL The procedure of installing battery bank should be omplied with strictly Otherwise you may encounter the hazardous of electric shock 1 A DC breaker must be connected between the battery pack and the UPS The capacity of breaker must be not less than the data specified in the general specification as follow 6000 6000XL 10000 10000XL 10000 10000XL 15000XL 20000XL psi 192VDC 192vpc 192vDC 192vDC 192vpc 192vDC 192vDC 192VDC a 102A may 2 Set the battery pack breaker in OFF position and connect the 16 pieces of batteries in series 3 To complete the connection by plugging the connector of the external battery cable into the external battery socket of the UPS Do not attempt to connect any loads to the UPS now You should conn
3. Battery Replacement 1 Before disposing of batteries remove conductive jewelry such as necklace wrist watches and rings 2 If it is necessary to replace any connection cables please purchase the original materials from the authorized distributors or service centers so as to avoid overheat or spark resulting in fire due to insufficient capacity 3 Do not dispose of batteries or battery packs in a fire they may explode 4 Do not open or mutilate batteries released electrolyte is highly poisonous and harmful to the skin and eyes 5 Do not short the positive and negative of the battery electrode otherwise it may result in electric shock or fire 6 Make sure that there is no voltage before touching the batteries The battery circuit is not isolated from the input potential circuit There may be hazardous voltage between the battery terminals and the ground 7 Even though the input breaker is disconnected the components inside the UPS are still connected with the batteries and there are potential hazardous voltages Therefore before any maintenance and repairs work is carried out switch off the breaker of the battery pack or disconnect the jumper wire of connecting between the batteries 8 Batteries contain hazardous voltage and current Battery maintenance such as the battery replacement must be carried out by qualified personnel who are knowledgeable about batteries No other persons should handle the batteries 10 Operating mod
4. 46 4 c 5 LI jj 25 50 75 100 10 9 Battery Low voltage warning The LCD display in Battery Low voltage warning is shown in the following diagram Notice When Battery low voltage or short back up time both low voltage marker and clock marker would bright synchronously 10 10 Battery Low voltage warning The LCD display in Battery Low voltage warning is shown in the following diagram LOAD STATUS VAC Note The above all diagrams temperature battery voltage Input voltage input frequency output voltage output frequency would alternately displayed in each mode once every three seconds 11 Communication Port 11 1 RS232 Interface The following is the pin assignment and description of DB 9 connector Pin Description VO Output 11 2 Intelligent slot This series is equipped with an intelligent slot for Webpower optional accessory or other optional card to achieve remote management of the UPS through internet intranet Please contact your local distributor for further information 11 3 AS400 Interface Option Except for the communication protocol as mentioned above this series UPS has AS400 card an optional accessory for AS400 communication protocol Please contact your local distributor for details The following is the pin assignment and description of DB 9 connector in AS400 card _Pin Description VO Pin Description VO UPS Fail Output 6 Bypass Output CEREA G
5. ND Input 8 UPSON Remote fa I I UPS FAIL BYPASS SUMMARY ALARM BATTERYLOW REMOTE SHUTDOWN LINE FAIL COMMON DB 9 Interface of AS400 communication protocol Appendix1 Rear Panel BACK VIEW of JAGUAR 6000 10000 amp oe 1 RS232 2 Inteligent Solt 3 Fan 4 Parallel Port 5 Input Breaker 6 Maintain Switch 7 Terminal Block Cover 8 Cable Rack 9 9 EPO BACK VIEW of LEOPARD 10000
6. attery the temperature and load could be displayed The operating mode code of the UPS is 03 1 When the UPS is running in Battery mode the buzzer beeps once every 4 seconds If tte ENTER button on the front panel is pressed for more than 1 second again the buzzer will stop beeping in silence mode Battery mode 10 4 Self Test mode The LCD display in Battery mode is shown in the following Diagram The information about the utility power the battery emperature and load could be displayed The operating mode code of the UPS is 04 LOAD STATUE Self Test mode 10 5 Parallel mode The LCD display in parallel mode is shown in the following diagram When the UPS operating in parallel mode the operating mode code of the UPS is P2 Parallel mode 10 6 Warning mode The LCD display in warning mode is shown in the following diagram the symbol WARNING is shown instead in code display LOAD STATUS BATTERY CAPACITY 25 50 75 100 Warning mode 10 7 Fault mode The LCD display in fault is shown in the following diagram The symbol MODE not be shown and the symbol FAULT is shown instead in code display BATTERY CAPACITY 25 50 75 100 Fault mode Bus Fault 10 8 Set Mode The LCD display in voltage set is shown in the following diagram Set Voltage The LCD display in Frequency set is shown in the following diagram Da LOAD STATUS z TEMP GUE
7. e ON position this step only for long backup time model 2 Press the ON button continuously for more than 1 second to power on the UPS and the buzzer will beep once UPS operates in No Output mode the mode code is 00 3 A few seconds later the UPS turn into Battery mode and the mode code is 03 3 Turn off the UPS with utility power supplied in Line mode 1 To turn off the inverter of the UPS by pressing the OFF button continuously for more than 1 second and the buzzer will beep once The UPS will turn into Bypass mode 2 Upon completion of the above to turn it off output of electric current of the UPS is still present In order to cut off the output from the UPS simply cut off the utility power supply a few seconds later there are not any display is shown on the display panel and no voltage output is available from the UPS output 4 Turn off the UPS with no utility power supplied in Battery mode 1 To power off the UPS by pressing the OFF button continuously for more than 1 second and the buzzer will beep once 2 When being powered off the UPS will turn into No Output mode Finally not any display is shown on the display panel and no voltage is available from the UPS output Suggestions Please turn off the connected loads before turning on the UPS and turn on the loads one by one after the UPS is working in INV mode Turn off all of the connected loads before turning off the UPS 7 Battery Mainte
8. e breaker must be not less than the specification as follow Model No Capacity of breaker JAGUAR 6000 gt 40A 250VAC JAGUAR LEOPARD 10000 260A 250VAC LEOPARD 15000 20000 2100A 250VAC The requirement of the output wiring is as follows e Vhen the distance between the UPSs in parallel and the breaker panel is less than 20 meters the difference between the wires of input amp output of the UPSs is required to be less than 20 eWhen the distance between the UPSs in parallel and the breaker panel is greater than 20 meters the ifference between the wires of input amp output of the UPSs is required to be less than 10 3 Operation and maintenance 1 To perform the general operation follow the stand alone operating requirement 2 Startup The units transfer to INV mode simultaneously as they start up sequentially in Line mode 3 Shutdown the units shut down sequentially in INV mode When the last one completes the shutdown action each unit will shut down the inverter simultaneously and transfer to Bypass mode It is easy to operate the equipment with no previous training You just need to read through this manual and operate according to the instructions in it Input switchboard Fun Peer i il LS OLI L s k z ry Pa Pe if 2 fH Load Load Load Load Parallel Installation Diagram 4 To perform the maintenance follow the stand alone requirement YVNOVI dO WV aDVIC DNI IA Output Ground Output Ne
9. e for all models The different codes could be displayed on the LCD screen corresponding to their own operating modes and they are illustrated as the follow Mode Code Table Parallel Mode Battery mode Battery test mode il Warning Code Table Charger Bad IP Fuse Open Battery Low er E Fault Code Table Inverter Fault Bus Fault 06 _ Overload Fault Over temperature Fault 08 other 09 45 10 1 Bypass mode The LCD display in Bypass mode is shown in the following diagram The information about the utility power the battery the UPS temperature and load could be displayed The operating mode code of the UPS is 01 The UPS will beep once every 2 minutes in Bypass mode 25 50 75 100 Bypass mode 10 2 Line mode The LCD display in Line mode is shown in the following diagram The information about the utility power the battery the temperature and load could be displayed The operating mode code of the UPS is 02 LOAD STATUS INPUT T vac LL BATTERY CAPACITY A CHARGING 25 50 75 100 ti Line mode If output overloaded the load percent is shown and alarm will keep twice every second You should get rid of some unnecessary loads one by one to decrease the loads connected to the UPS less than 90 of its nominal power capacity 10 3 Battery mode The LCD display in Battery mode is shown in the following diagram The information about the utility power the b
10. ect the input power wire to the right position first And then set the breaker of the battery pack in the ON position After that set the input breaker in the ON position The UPS begins to charge the battery packs at the time 5 4 Parallel operation 1 Brief introduction of the redundancy N X is currently the most reliable power supply structure N represents the minimum UPS number that the total load needs X represents the redundant UPS number i e the fault UPS number that the system can handle simultaneously The bigger the X is the higher reliability of the power system is For occasions where reliability is highly required N X is the optimal mode As long as the UPS is equipped with parallel cables up to 3 of them can be connected in parallel to realize output power sharing and power redundancy 2 Parallel installation 1 Users need to opt a standard 25 pin communication cable which should have 25 cores corresponding stitches and shield as the UPS parallel cable The length of the parallel cable is appropriate to be less than 3 m 2 Strictly follow the stand alone wiring requirement to perform the input wiring of each UPS 3 Connect the output wires of each UPS to an output breaker panel first and then connect the wiring to the load via the breaker panel 4 The parallel UPS must be equipped with battery individually 5 Please refer the figure followed to see the wiring of parallel operation The capacity of th
11. guration equipotential earth bonding to the external UPS battery cabinets m An integral single emergency switching device which prevents further supply to the load by the UPS in any mode of operation should be provided in the building wiring installation m An appropriate disconnect device as short circuit backup protection should be provided in the building wiring installation m For three phase equipment connection to an IT power system a four pole device which disconnect all phase conductors and the neutral conductor should be provided in the building wiring installation m This is permanently connected equipment it must be installed by qualified maintenance personnel m Earth connection essential before connecting to the building wiring terminal 1 2 Operation m Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any time since this would cancel the protective earthing of the UPS system and of all connected loads m The UPS output terminal block may be electrically lived even if the UPS system is not connected to the building wiring terminal m In order to fully disconnect the UPS first press the OFF button then disconnect the mains lead m Ensure that no liquid or other foreign objects can enter the UPS m The UPS can be operated by any individuals with no previous experience 1 3 Maintenance servicing and faults m The UPS operates with hazardous voltages Repairs may be carried out
12. he rear panel of the UPS please refer to the appearance diagram 2 For JAGUAR 6000 UPS it is recommended to select the UL1015 10AWG 6mm2 wire or other insulated wire which complies with AWG Standard for the UPS input and output wirings 3 For JAGUAR LEOPARD 10000 UPS it is recommended to select the UL1015 8AWG 10mm2 wire or other insulated wire which complies with AWG Standard for the UPS input and output wirings 4 For LEOPARD 15000 20000 UPS it is recommended to select the UL1015 6AWG 25mm2 wire or other insulated wire which complies with AWG Standard for the UPS input and output wirings Note Do not use the wall receptacle as the input power source for the UPS as its rated current is less than the UPS s maximum input current Otherwise the receptacle may be burned and destroyed 5 Connect the input and output wires to the corresponding input and output terminals according to the following diagram o o o e o o L N Input Ground Output Ground Input Neutral Input Line Bat Output Neutral Output Line Bat Note you must make sure that the input and output wires and the input and output terminals are connected tightly 6 The protective earth ground wire refers to the wire connection between the equipment which consumes electric equipment and the ground wire The wire diameter of protective earth ground wire should be at least as above mentioned for each model and green wire or green wire wi
13. nance e This series UPS only requires minimal maintenance The battery used for standard models are value regulated sealed lead acid maintenance free battery These models require minimal repairs The only requirement is to charge the UPS regularly in order to maximize the expected life of the battery When being connected to the utility power whether the UPS is turned on or not the UPS keeps charging the batteries and also offers the protective function of overcharging and over discharging e The UPS should be charged once every 4 to 6 months if it has not been used for a long time e In the regions of hot climates the battery should be charged and discharged every 2 months The standard charging time should be at least 12 hours e Under normal conditions the battery life lasts 2 to 4 years In case if the battery is found not in good condition earlier replacement should be made Battery replacement should be performed by qualified personnel e Replace batteries with the same number and same type of batteries e Do not replace the battery individually All the batteries should Be replaced at the same time following the instructions of the battery supplier e Normally the batteries should be charged and discharged once every 4 to 6 months Charging should begin after the UPS shuts down automatically in the course of discharging the standard charging time for the standard UPS should be at least 12 hours 8 Notes for Battery Disposal and
14. only by qualified maintenance personnel m Caution risk of electric shock Even after the unit is disconnected from the mains power supply building wiring terminal components inside the UPS are still connected to the battery which are potentially dangerous m Before carrying out any kind of service and or maintenance please disconnect the batteries Verify that no current is present and no hazardous voltage exists in the capacitor or BUS capacitor terminals m Batteries must be replaced only by qualified personnel mCaution risk of electric shock The battery circuit is not isolated from the input voltage Hazardous voltages may occur between the battery terminals and the ground Verify that no voltage is present before servicing m Batteries have a high short circuit current and pose a risk of shock Take all precautionary measures specified below and any other measures necessary when working with batteries remove all jewellery wristwatches rings and other metal objects use only tools with insulated grips and handles m When changing batteries replace with the same quantity and the same type of batteries m Do not attempt to dispose of batteries by burning them It could cause explosion m Do not open or destroy batteries Effluent electrolyte can cause injury to the skin and eyes It may be toxic m Please replace the fuse only by a fuse of the same type and of the same amperage in order to avoid fire hazards m Do not di
15. re which could be displayed from 0 to 999 C The two items alternate displayed once every three seconds indicates the battery capacity For example 25 and 50 lighting synchronous it means current battery capacity is 50 LOW BAT lighting indicates the battery is weak and the UPS should shut down soon BATTERY FAULT lighting indicates indicates the present load value For example 25 and 50 lighting synchronous it means current load is 50 When load 100 lighting and the OVER LOAD lighting with warning it means ups in overload Indicates ups input voltage value output voltage value output frequency value which could be displayed from 0 to 999VAC The four items alternate displayed once every three seconds 208 220 230 240VAC The four value of the output voltage could be selected 50 60HZ the two frequency value of the output voltage could be selected N licates have mains power and when mode code display 02 that mean the ups working in Line mode CHARGING ECO lighting indicates ups working in ECO N _ Lighting indicates ups chargin fs lighting and mode code display 03 that mean the ups working in battery mode Nag ig coinstantaneous and mode code display 03 that means UPS working in Bypass and LOW BAT lighting coinstantaneous and UPS with warning that means Battery low voltage the ups will would shut down soon 5 Installation the system may be installed and wired only by qualified elec
16. smantle the UPS except qualified maintenance personnel 1 4 Transport m Please transport the UPS only in the original packaging to protect against shock and impact 1 5 Storage m The UPS must be stockpiled in the room where it is ventilated and dry 2 Description of commonly used symbols Some or all of the following symbols may be used in this manual It is advisable to familiarize yourself with them and understand their meaning Symbol and Explanation i Alert you to pay E EN Caution of high Turn on the UPS Overload indication Alarm silence idle or shut down an Alternating current Do not dispose with source AC ordinary trash Direct current source DC 3 Introduction 3 1 System and model description The On Line Series is an uninterruptible power supply Incorporating double converter technology It provides perfect protection specifically for strict load The double converter principle eliminates all mains power disturbances A rectifier converts the alternating current from the socket outlet to direct current This direct current charges the batteries and powers the inverter In the event of power failure the maintenance free batteries power the inverter Thus the inverter generates a sine wave AC power which permanently supplies the loads Designed with the proven on line double conversion architecture this series of UPS offers the greatest degree of availability in power protection and provides contin
17. th yellow ribbon wire is used 7 After having completed the installation make sure the wiring is correct 8 Please install the output breaker between the output terminal and the load and the breaker should with leakage current protective function if necessary 9 To connect the load with the UPS please turn off all the loads first then perform the connection and finally turn on the loads one by one 10 No matter the UPS is connected to the utility power or not the output of the UPS may have electricity The parts inside the unit may still have hazardous voltage after turning off the UPS To make the UPS have no output power off the UPS and then disconnect the utility power supply 11 Suggest charging the batteries for 8 hours before use After connection turn the input breaker in the ON position the UPS will charge the batteries automatically You can also use the UPS immediately without charging the batteries first but the backup time may be less than the standard value 12 If it is necessary to connect the inductance load such as a monitor or a laser printer to the UPS the start up power should be used for calculating the capacity of the UPS as its start up power consumption is too big when it is started Lollo 0 0 le o Input Ground Output Ground Input Neutral Input Line Bat Output Neutral Output Line Bat Input and Output Terminal Block wiring diagram of JAGUAR
18. the output power must be derated in use please refer to the following Altitude M 4 Display Panel O s A 25 50 75 100 SHORT OVER LOAD LCD Screen ara z m T fe lx dn o qa On Off Button Select Button Enter Button I he following table describes the function of the button switches of the front panel This button has two functions Turning on the UPS system By pressing this button the UPS system turns on Shut off the UPS system When mains power is normal the UPS System switches to ON OFF Button oressing OFF button and the inverter is off if the ups system is in bypass mode or self test mode the output frequency could be ee ing Select button and confirmed b ing Enter button Enter Button if the ups system is in bypass mode or self test mode the output frequency could be selected by pressing Select button and confirmed by pressing Enter button Mode Fault Warni ng code Set type Load Information Input output voltage and Battery Voltage frequency UPS temperature information Battery Indication of UPS information work mode Display FAULT lighting indicates mode code fault code and warning code which could be displayed from 0 to99 SET lighting indicates the set code type V set voltage F set frequency BATTERY lighting indicates the battery voltage value which could be displayed from 0 to 999Vdc TEMP lighting indicates the ups inside temperatu
19. tricians in accordance with applicable safety regulations 5 1 Unpacking and Inspection 1 Unpack the packaging and check the package contents The shipping package contains e A UPS e A user manual e A communication cable e A battery cable for XL series only 2 Inspect the appearance of the UPS to see if there is any damage during transportation Do not turn on the unit and notify the carrier and dealer immediately if there is any damage or lacking of some parts 5 2 Input and output power cords and protective earth ground installation 1 Notes for installation 1 The UPS must be installed in a location with good ventilation far away from water inflammable gas and corrosive agents 2 Ensure the air vents on the front and rear of the UPS are not blocked Allow at least 0 5m of space on each side 3 Condensation to water drops may occur if the UPS is unpacked in a very low temperature environment In this case it is necessary to wait until the UPS is fully dried inside out before proceeding installation and use Otherwise there are hazards of electric shock 2 Installation Installation and wiring must be performed in accordance with the local electric code and the following instructions by Professional personnel or safety please cut off the mains power switch before installation The battery breaker also needs to be cut off if it is a long backup time model XL model 1 Open the terminal block cover located on t
20. uous high quality AC power to connect strict load especially for the basic equipments in some areas as finance communication government traffic manufacture education and so on This manual is applicable to the following models Standard Long back up 10kVA UPS JAGUAR LEOPARD 1000XL External battery bank time ISkVA UPS LEOPARD 15000XL External battery bank 3kVAS UPS LEOPARD 20000XL External battery bank XL Model Long backup time 3 2 Product Specification and Performance 1 General specification Frequ input full load a Weight Rating H2 ee Voltage ae E JAGUAR 176 276 JAGUAR 176 276 LEOPARD 304 478 LEOPARD 304 478 LEOPARD 304 478 2 Electrical performance INPUT Single phase 50 60Hz t5 JAGUAR 6000 10000 220VAC 230VAC adjustable gt 0 99 Full load Three phase 450 LEOPARD 10000 20000 380VAC 220 VAC si gt 0 95 Full load 380VAC 230 VAC J OUTPUT Voltage TON Frequency tolerance Distortion Overload capacity Current regulation factor crest ratio Synchronized 105 125 load 3 46 54Hz in Line mode THD lt 2 transfers to bypass 1 3 mode after 1minutes 3 1 AC mode 1 of Full load 130 load se normal frequency in Linear load Transfers Bypass pane mode mode after 30second 3 Operating Environment Humidity Altitude Storage temperature 0 C40 C lt 1000m 0 C40 C Note if the UPS is installed or used in a place where the altitude is bove than 1000m
21. utral il Output Line Input Line Input Neutral Input Ground J8 ye aJg ndino LSdN layeeig ndino ZSdn JayeaIg Ndu ZSdN g Jayeaig jnduj LSdN JJyvdOod HO NVADVId DNIHIAMA Output Ground Output Neutral i Output Line Input Line Wire C Input Line Wire B InputLine Wire A Input Neutral Input Ground JayeaJg ndino LSdN Jayeasg jndu zSdn A JayeaJg Indul LSdN y kaa N N l Ly cl e AI 6 Operation 6 1 Operation Mode 1 Turn on the UPS with utility power supplied in Line mode 1 After you make sure that the power supply connection is correct and then set the breaker of the battery pack in the ON position this step only for long backup time model after that set the input breaker in the ON position At this time the fan rotates and the UPS supplies power to the load via the bypass The UPS operates in Bypass mode the mode code is 01 2 To power on the UPS by simply pressing the ON button continuously for more than 1 second the buzzer will beep once 3 A few seconds later the UPS turn into Line mode and the mode code is 02 If the utility power is abnormal the UPS will operate in Battery mode without output interruption of the UPS 2 Turn on the UPS with no utility power supplied in Battery mode 1 After you make sure that the breaker of the battery pack is in th
Download Pdf Manuals
Related Search