GSM WIRELESS DIGITAL ALARM SYSTEM USER GUIDE
Contents
1. cellular phone call will be made to the first programmed phone number and your voice message will be heard by the answering party or coded message sent to your central monitoring station The system will then proceed to call up to an additional 5 telephone numbers if you have programmed it todo so Atthe same time a text message indicating an alarm will be sent to the designated telephone 2 If the first telephone number does not answer within 40 seconds the alarm panel will proceed to call the second listed telephone number and so forth until a call is answered and the alarm acknowledged 16 To acknowledge an alarm you must press the button of your telephone or you can de activate the alarm system by pressing the 5 button of your telephone You may press the 1 button to listen to the area around your alarm panel or press 2 to turn on your siren if programmed or press 3 to turn off the siren if programmed or press 4 to activate the alarm system again If you wish to hear your recorded message press the key REMOTE CONTROL FUNCTION 1 Your Diamond Designs Alarm System is capable of being operated by remote control with most telephones with either telephone keypad commands or via text messages 2 To control your alarm system via a telephone keypad first you must dial the telephone number of your system After approximately 3 4 rings the system will answer and acknowledge you with o2. GSM WIRELESS DIGITAL ALARM SYSTEM USER GUIDE Please read it carefully before installation and operation Your New Diamond Designs Alarm works with a GSM SimCard via the cellular phone system to call up to 6 phone numbers with alarm information Additionally your new alarm system will optionally send Text Messages via your local cellular system Installation amp Instruction This system requires a GSM SIM Card You can use either a prepaid minutes card or on a monthly service It is Important That Your Cellular Alarm telephone number be kept confidential to protect your alarm system It is important that you carefully follow these installation instructions for the proper operation of your new alarm system 1 Put the small GSM SIM Card in the slide tray as shown below and slide it into the slot PRIOR TO plugging in your alarm system This Is Important 2 Install your alarm sensors according to your plan for protecting your property Extra sensors are available Once the sensors are installed be sure that they are activated to the on position Plug in a siren if you wish to use that feature 3 Plug the supplied 110 120 or 220 240V power supply into an outlet and plus the barrel end of the power cord into the back of the alarm panel The green POWER LED light will turn on 4 The alarm system will now initialize and you will hear one buzz sound 5 The alarm will auto check the GSM network and log on Initiali
3. is disturbed the alarm panel will automatically send a text message to the designated telephone that the AC power shut off Once the a c power is back on it will automatically send a text message that AC power recovered Notice The Use of an alarm system is subject to a wide variety of factors which can affect the utility and effectiveness of the alarm system we do not assume or represent the assumption any liability for any loss resulting from the use of this alarm equipment It is important that the user install the equipment properly maintain the equipment and operate the alarm system in an effective manner The purchaser or user of this alarm equipment agrees that the sole liability of us which is limited to the replacement of the alarm system should in it s sole judgment determine that such replacement is necessary Specifications GSM main unit 100 240AC 6DC 2 5A Approx Extended Antenna Receiving Distance 100Yards Without Signal Interference Stand by current lt 90mA Alarm current lt 200mA Power Consumption 0 5W Built in Li lon Back Up Battery 1800mA 3 6V
4. ne BUZZ sound Input your 4 digit password and if correct the alarm system will acknowledge with two BUZZ sounds If the password is incorrect you will hear a continuous BUZZ The alarm system will hang up if you input the wrong password three times After hearing the two BUZZ sounds you can complete the following actions 1 is for listening for sounds in the protected area for 20 seconds repeat for additional 20 second periods 2 will turn on the siren if it is programmed for this function 3 will turn the siren off if it is programmed for this function depending on current status 4 will activate your alarm system A C Power Indication 5 will deactivate your alarm system a If your system has an internal battery backup that is 3 You can control your alarm system via a text message however you must use the specific text order as shown with capital letters The message is composted of your password plus The test messages are as follows Password ARM i e 1234ARM Reply Message Host Is Activated Password DISARM i e 1234DISARM Reply Message Host Is Deactivated Password ONSIREN i e 1234ONSIREN Reply Message The Siren ls Opened Password OFFSIREN i e 1234OFFSIREN Reply Message The Siren Is Closed Password CHECK i e 1234CHECK Reply Message Host Is Activated OR Host Is Deactivated working properly and the a c power supply
5. ose the telephone number is 555 1234 you would input the following with your alarm keypad 1 5551234 The panel will make one short and one long BUZZ sound to indicate successful input or a continuous BUZZ sound if the input was not successful To input a second phone number your input would be 2 5551235 etc To dial outside your local area code you will need to input the area code i e 2 18095551235 If you are using a central monitoring station it may be best to program that phone number as 1 the indicating the number of minutes For instance 3 To delete a telephone number from the calling sequence if you wish the siren to sound for 3 minutes prior to input on your keypad 1 to remove the first self resetting then input 9 43 If you wish to have stored telephone Input 2 to remove the second the siren sound continuously the input would be stored phone number etc 9 4 The siren will now sound continuously until 4 To program the keyfob and detectors by inputting 9 you acknowledge the alarm and reset the system 4 90 password four digitals The original 10 Password Setup Your Diamond Design Alarm System password is 1234 thus enter 9 901234 to comes coded with a default password of 1234 You should program the keyfob and detectors change your password to protect against unauthorized alarm 5 Cancel the keyfob 9 91 passwo
6. rd changes 6 Cancel other detectors 9 92 password To change your default password to 6789 enter the following 7 How to learn the wireless siren Horn Press 9 on your keypad 7 6789 The password can be any 4 digit 93 Code Number The number on the flash siren 8 number digitals 11 Your Diamond Design Alarm System can be programmed 8 The alarm siren can be plugged in for use inside or to work with many central alarm monitoring stations You outside your protected premises or left unplugged for a will be assigned a unique ID code by your central monitoring silent alarm station which can be inputted to your alarm panel To enter 9 Setting Siren Reset time You can customize the amount a 6 digit code of 123456 input the following on of time the siren will sound by inputting 9 4 with your keypad 8 123456 12 Text Message Your Diamond Design Alarm will send a short text message to one telephone capable of receiving text messages generally a cellular phone To program this function input the following on your keypad 0 phone number for example with 555 1234 being the phone number the input would be 0 5551234 If calling outside your local area you may need to add an area code i e 0 18095551234 When an alarm is triggered the selected telephone will receive a short text message indicating that a specific zone has been triggered or that the po
7. wer has been lost to the alarm panel or that the power has been turned back on If you do not wish to use the text message function enter the following on your keypad 0 to delete any previously selected telephone number 13 It is important that you test your system once you have set it up to assure correct programming You should test it several times to assure every possible function is working as you have directed It is also important to test your system monthly to assure correct function 14 15 You can activate your alarm system by pressing the lock symbol on your keyfob or by making a telephone call to your system as noted under Remote Control Function System Recovery Should you wish to return the alarm panel to it s original programmed configuration you should input the following on your keypad 9 69Password if your password is 1234 then the command would be 9 691234 IMPORTANT Press any keypad number once following system recovery You will hear two BUZZ sounds if the recovery was successful if the recovery failed the BUZZ will be continuous until you try again This action will recover all original settings except your system password which will remain as you have previously set it When An Alarm Signal Is Received 1 When one of the sensors of your alarm system is activated the alarm panel led in the lower right area next to the word ALARM will begin to blink immediately a
8. zation time is about 1 minute The red LED flashes as initialization proceeds 6 As initialization is completed you will hear on long buzz sound the ARM LED light stops flashing and is on continuously This means the entire system is activated Use your key fob off on switch to immediately turn the system off If initialization is successful the red NETWORK LED will flash If initialization failed you will hear a constant short buzz sound This indicates that the SIM Card is out of network or the initialization was not correctly completed Assure that your SIM Card is correctly installed and repeat steps 2 to 6 Screw the antenna into the input jack of the GSM alarm panel ALARM SETUP All THE SETTING SHOULD DISARM THE ALARM SYSTEM 1 You have the option of setting up a 10 second recorded voice message which will be played when the alarm calls up to 6 phone numbers Input with your alarm keypad the following 9 80 Password The original password is 1234 thus enter 9 801234 to record your message The ARM LED will be constantly on Face the GSM main panel from a distance of about 12 inches and record your message Then press any key on your alarm keypad and you will hear one short and one long BUZZ This indicates recording was successfully You can set up six 6 telephone numbers to be called by the alarm panel To program the first telephone number input from your alarm keypad supp
Download Pdf Manuals
Related Search