QuickTake 30 Sample Pump 228-9530 Operating Instructions 40079
Contents
1. FLOF Digital display Flow fault Fault restart will attempt to restart the pump every 10 seconds up to five times Cumulative run time can be displayed by pressing Press again to return to the fault FLOF display If pump does not automatically restart attempt to correct the flow blockage then press A V to place pump in Hold Press A V to resume sampling Fault restart user disabled Cumulative run time can be displayed by pressing Press again to return to the FLOF display Attempt to correct flow blockage and press A V to place pump in Hold Press A V to resume sampling The flow fault and flow fault restart features can be enabled or disabled by the user as desired See Advanced Disabling Alarm and Fault Features 13 Setup Enabling Advanced Setup Intermittent Sampling Intermittent Sampling allows the pump to be programmed to run for a specific number of minutes up to 999 to shut off for a programmed Vt length of time and to continue sampling on and off for a predetermined number of cycles e g program the pump to run three cycles n of 15 minutes each r with a five minute delay d between each cycle Le Digital display Intermittent Sampling LL Entering Intermittent Sampling Mode Press A or Y to scroll to Intt Press to enter the intermittent sampling setup mode Setting Run Time r 1 Press A or Y to increase or decrease run time The di2. 3 Press A or Y to increase or decrease the flow until the desired flow rate is displayed on the calibrator 4 Press A flashing Stor will appear on the LED To save new setting Press A V The pump will stop running gt E Gr To ignore new setting Press The pump will i stop running Digital display Store setting Note A security code is not needed to change flow rate It is only required when changing factory settings To change factory settings see Advanced Setup Setup Press A or Y to scroll through the run time presets on the LED Run Time Mode LED Display Timed Run defaults 15 10 5 2 and 1 min t xx Intermittent Sampling Intt Continuous Run Cont The user may change run time presets See Advanced Setup Programming Your Own Run Time Presets Timed Run Run time accumulates only while pump is running predetermined time from 1 to 999 minutes selected from presets The user starts the pump running and the pump automatically stops running after the sample time has Timed Run mode is designed to perform one sample for a J N _ Digital display Timed Run 2 minutes elapsed 1 Press A or Y to scroll to the desired run time preset F 2 Press A V to select the desired preset The pump will start running and the LED will display a count down to Digital display Run time remaining is zero run time remaining below one minute is displayed f p SECONAS i
3. will not appear as an option during setup of first preset 4 When the LED displays the desired time or mode press to move to the next preset time F a Repeat Steps 3 and 4 for each preset up to eight presets The sequence will repeat from one to eight Digital Display When finished press A V Stor will display on the Time set for preset 1 LED To save new settings Press A V The pump will m return to normal pump operation AF OT To ignore new settings Press The pump will return to normal pump operation Digital display Store settings Note While programming presets scrolling below Intt will display End after the first preset is selected Choosing End will truncate the stored preset sequence see below For example if the user desires to store only two presets preset time 3 can be set to End shortening the number of presets to scroll through Times programmed for preset times Pt 4 through 8 will not display until the presets are changed to make them display or the factory defaults are reset see Resetting Pump to Manufacturer Default Settings Presets Sequence Preset 8 Preset 8 Preset 7 Preset 7 Preset 6 Preset 6 Preset 5 Preset 5 Preset 4 Preset 4 Preset 3 Preset 3 Preset 2 Preset 2 Preset 1 Preset 1 Manufacturer Default Presets The pump returns to the beginning preset at the first End it encounters This allows the user to sh
4. not a battery eliminator Therefore it will not provide indefinite run times To navigate presets and displays Press A or Y to scroll through presets or displays To select a run time preset and run the pump Scroll to desired run time preset Select preset by pressing A V The pump will start to run Selecting the Available Presets Press A or Y To run the pump Press A V To place the pump in hold Press A V To repeat a sample run From Done reset rSEt or sampling error SErr press A V to return to run time preset Press A V to sample To turn off LED Pump automatically turns off LED after it is idle for 4 minutes User can reactivate the LED by pressing and holding To interrupt run terminate a sample or reset pump From Hold press Sample reset rSEt will display Press A Y to reset pump or to ignore reset and return to Hold To set flow or calibrate See Calibration and Setting Flow for details 1 Connect a flowmeter to the pump inlet 2 Scroll to any run time preset Press and hold CAL for 2 seconds to enter calibration mode pump will start running 3 Press A or Y to change flow rate until desired flow appears on the calibrator Flow rate does not display on LED 4 Press and Stor will display Press A V to save setting or to ignore changes Mounting Sampling Media Sampling with a Spore Trap Cassette Use the cassette adapter
5. sequence Programming Sequences e To activate pump LED Press and hold for 2 seconds e To check battery status Press e To choose a run time preset Press A or Y to scroll through presets Once desired preset displays press A Y to start sampling e To Run or Hold Press A F e To repeat a sample run From Done reset rSEt or sampling error SErr press A V to return to run time preset Press A V to sample e To change or calibrate flow Note Flow rate does not appear on LED Press A or Y and scroll to a run time preset Press and hold CAL for 2 seconds Does not require a security code Press amp or W to change flow rate until desired flow appears on calibrator Press When Stor displays press A V to save setting or to ignore changes to flow setting e To interrupt run terminate a sample or reset pump While in Hold press Sample reset rSEt will display Press A V to reset pump or to ignore reset and return to Hold www skcinc com SKC Inc 863 Valley View Road Eighty Four PA 15330 Description The QuickTake 30 Sample Pump is a portable battery powered air sampling pump that maintains constant airflow from 10 to 30 L min for use with impactors spore trap cassettes such as Versa Trap asbestos cassettes or other samplers requiring flows to 30 L min A diaphragm pump operating with a closed loop flow control system the QuickTake 30 maintains true constant flow The QuickTak
6. supplied with the pump Insert the tube end of the adapter into the pump inlet up to the flange Remove the seal from the outlet of the cassette and push the cassette onto the bowl end of the adapter until a firm seal is established Empty cassette Cassette adapter with adapter spore trap cassette Calibration Note Flow rate can be calibrated by pushing the bowl end of a second cassette adapter onto the spore trap cassette inlet seal removed attaching flexible tubing to the tube end of the second adapter and attaching the other end of the flexible tubing to the outlet of a calibrator Sampling with Sampling Wand Accessory Cat No 228 9521 Tubing adapter Included with wand ee 6 I Make 30 cassette JA a Cassette adapter 0 Tubing Included with wand Insert the tube end of a cassette adapter into the hole on the top end of the sampling wand accessory see above up to the center flange Remove the seal from the outlet of the cassette and push the cassette onto the bowl end of the adapter until a firm seal is established Insert the tubing adapter on the flexible tubing supplied with wand into the pump inlet up to the center flange Sampling with a BioStage Impactor Use with Mounting Bracket accessory Cat No 228 9531 1 Place BioStage on L shaped bracket Align BioStage outlet to the 10 o clock position on the bracket Secure with thumbscrew on bottom of bracket BioStage outlet Thumbscrew s
7. 2 pumps QuickTake 30 3 pumps 3 Ship to SKC freight prepaid to the following address SKC Inc National Service Center 863 Valley View Road Eighty Four PA 15330 O SKC Inc will accept for repair any SKC product that is not contaminated with hazardous materials Products determined to be contaminated will be returned unserviced Replacing parts with non SKC parts voids the manufacturer warranty Li lon Battery Shipment Rechargeable lithium ion batteries for use with SKC sampling pumps have been tested in accordance with the UN Manual of Tests and Criteria and are designated as UN3091 For air shipments Rechargeable lithium ion batteries in SKC pumps are subject to the A 45 exemption to the IATA regulations and are not regulated for air shipments This information must be written on the shipping document when shipping by air For ground shipments US DOT regulations specify a limit of 24 or fewer battery cells in one shipping box If you exceed 3 QuickTake 30 pumps with battery packs in one shipping box specific shipping requirements must be followed Contact SKC for more information or refer to the regulatory authority in your area SKC INC LIMITED ONE YEAR WARRANTY 1 SKC warrants that its instruments provided for industrial hygiene environmental gas analysis and safety and health applications are free from defects in workmanship and materials under normal and proper use in accordance with operating instru
8. atically reset to zero and count up to 999 minutes again until the user manually stops the pump 2 Press A V to place the pump in Hold when the desired sampling time has elapsed The LED will display cumulative run time and Hold alternately To continue sample run Press A V To terminate sample and reset pump Press while in Hold Sample Reset rSEt will flash on the LED Press A V User Options During Continuous Run Sampling Viewing battery status Press X Display will automatically return to cumulative run time after five seconds or press H H E again Hold mode Press A V while the sample is running to place the pump and timer in Hold Hold and Hol yd cumulative run time will display alternately Press A V while in Hold to continue the sample run Terminating a sample and resetting the pump ir 5 E E Press while in Hold Sample Reset rSEt will flash on the LED To terminate sample and reset pump Press A V To continue sample run Press to return the display to Hold Press AV For Intermittent Sampling see Advanced Setup Sampling 2 3 QuickTake 30 with cassette adapter and a spore trap cassette Ensure that the battery has sufficient capacity for the desired sampling time see Operation Battery Status Indicators Calibrate the QuickTake 30 for the desired flow rate see Calibration and Setting Flow Place the pump in the sampling location O Protec
9. ctions provided with said instruments The term of this warranty begins on the date the instrument is delivered to the buyer and continues for a period of one 1 year This warranty does not cover claims due to abuse misuse neglect alteration accident or use in application for which the instrument was neither designed nor approved by SKC Inc This warranty does not cover the buyer s failure to provide for normal maintenance or improper selection or misapplication This warranty shall further be void if changes or adjustments to the instrument are made by other than an employee of the seller or if the operating instructions furnished at the time of installation are not complied with 2 SKC Inc hereby disclaims all warranties either expressed or implied including any implied warranties of merchantability or fitness for a particular purpose and neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of these instruments No a tion of the goods being sold has been made a part of the basis of the bargain or has created or amounted to an express warranty that the goods will conform to any such description Buyer shall not be entitled to recover from SKC Inc any consequential damages damages to property damages for loss of use loss of time loss of profits loss of income or other incidental damages Nor shall buyer be entitled to recover from SKC Inc any consequential damages resulting from
10. defect of the instrument un but not limited to any recovery under section 402A of the Restatement Second of Torts 3 This warranty extends only to the original purchaser of the warranted instrument during the term of the warranty The buyer may be required to present proof of purchase in the form of a paid receipt for the instrument 4 This warranty covers the instrument purchased and each of its component parts 5 In the event of a defect malfunction or other failure of the instrument not caused by any misuse or damage to the instrument while in possession of the buyer SKC Inc will remedy the failure or defect without charge to the buyer The remedy will consist of service or replacement of the instrument SKC Inc may elect refund of the purchase price if unable to provide replacement and repair is not commercially practicable 6 a To obtain performance of any obligation under this warranty the buyer shall return the instrument freight prepaid to SKC Inc at the following address SKC Inc National Service Center 863 Valley View Road Eighty Four PA 15330 USA b To obtain return authorization information or for further information on the warranty performance you may telephone 724 941 9701 at the above address See Service Policy section in operating manual if applicable 7 This warranty shall be construed under the laws of the Commonwealth of Pennsylvania which shall be deemed to be the situs of the contract for purchase o
11. e 30 features a programmable timer that provides up to eight programmable run time presets of 1 to 999 minutes continuous run with manual shut off or intermittent sampling A rechargeable lithium ion battery pack provides effective run times see Performance Profile Typical Cumulative Run Time on p 3 Cassette Adapter Tubing Adapter Handle Inlet for easy shown without adapter portability LED indicates active battery charging High contrast LED display for readout of presets run time and battery status Calibration mode button Up arrow Charging jack increases flow and time and scrolls through presets Star button activates LED and toggles Par between displays timed run alarm on side of case not shown Down arrow decreases flow and time and scrolls through presets Printed Quick Guide Performance Profile Flow range Flow compensation accuracy Compensating flow back pressure range 10 to 30 L min 5 of set flow 10 L min at 90 inches water back pressure 20 L min at 50 inches water back pressure 30 L min at 15 inches water back pressure Typical Back Pressure of Sampling Media inches water Filter Pore Size um 25 mm MCE 0 8 65 80 103 148 25 mmMCE 045 138 172 gt 200 37 mmPv50 9 n 15 21 Compare the information in this table to pump compensation range to determine appropriate applications Power Battery recharge
12. ecuring Short leg BioStage of bracket BioStage outlet aligned to 10 o clock position 2 Place L shaped bracket to the right on the pump faceplate with the short leg of the bracket fitting over the right edge of the pump Align hole on short leg of bracket with the hole on the side of the pump Secure bracket to pump with thumbscrew Y Thumbscrew securing bracket Bracket Inlet Inlet adapter adapter BioStage inserted into inlet tubing g outlet 3 Insert the inlet adapter included with bracket into the pump inlet and connect inlet adapter tubing to the BioStage outlet Thumbscrew securing bracket Calibration and Setting Flow Use a primary standard calibrator to calibrate pump flow rate Calibrate flow rate with representative sampling medium in line Note Use a second cassette adapter to attach calibrator to a spore trap cassette Tubing Spore trap cassette Cassette adapter Calibrator outlet Pump inlet Calibration with a spore trap cassette 1 Using 3 8 inch ID flexible tubing and appropriate adapters connect the inlet of the pump to the outlet of a representative sampling medium and a primary standard calibrator to the inlet of the representative sampling medium as shown above 2 Scroll to any run time preset Press and hold the CAL button for two seconds The pump will start running and a flashing CAL will appear on the LED Digital display Calibration mode
13. f SKC Inc instruments 8 No other warranty is given by SKC Inc in conjunction with this sale Form 3755 Rev 0207 21 Ordering Information Description Cat No QuickTake 30 Sample Pump includes battery pack and cassette and tubing adapters requires 223 245 charger accessory below 228 9530C QuickTake 30 Sample Pump and Charger includes one pump with battery pack AC charger adapter 100 240 V cassette and tubing adapters and tubing 228 9530 QuickTake 30 Sample Pump Rotameter and Charger includes one pump with battery pack AC charger adapter 100 240 V cassette and tubing adapters rotameter and tubing 228 9530A QuickTake 30 BioStage Pump Kit includes pump and charger as described above Standard BioStage Impactor mounting bracket with inlet adapter calibration adapter rotameter and deluxe carry case 228 9530K Replacement Parts Replacement Inlet Filters pk 50 P40021A Stem Tubing Adapter pk 2 P31239 Cassette Adapter P33100 Reducing Adapter for Tubing 3 8 inch to 1 4 inch pk 2 P31211 Replacement Battery Pack P75689 Replacement Stack for QuickTake 30 P21266 Accessories Worldwide Charger Adapter 223 245 Defender Primary Flowmeter 300 ml min to 30 L min includes lead acid battery multi plug charger 100 240 V Optimizer 110 Software and 1 meter serial cable 717 510H Sampling Wand telescopes to 34 inches for ductwork and hard to reach locations includes 6 ft of tubing 228 9521 Tr
14. ipod Stand telescopes to 5 ft for mounting sample media QuickTake 30 pump will not mount on this stand 225 9536 Mounting Bracket for BioStage Impactor includes inlet adapter 228 9531 Rotameter to check approximate flow rate 320 100 Tygon Tubing 3 8 inch ID 10 ft 225 1351 50 ft 225 1352 Li lon Battery Shipment Rechargeable lithium ion batteries for use with SKC sampling pumps have been tested in accordance with the UN Manual of Tests and Criteria and are designated as UN3091 For air shipments Rechargeable lithium ion batteries in SKC pumps are subject to the A 45 exemption to the IATA regulations and are not regulated for air shipments This information must be written on the shipping document when shipping by air For ground shipments US DOT regulations specify a limit of 24 or fewer battery cells in one shipping box If you exceed 3 QuickTake 30 pumps with battery packs in one shipping box specific shipping requirements must be followed Contact SKC for more information or refer to the regulatory authority in your area
15. n seconds with a colon The pump will stop and beep four times The display will flash Done _ 3 Press to return to the run time preset display If the A DU user wishes to repeat the sample press A V DOITE Digital display Sample run completed User Options During Timed Run Sampling Viewing battery status Press Display will automatically return to run time B A E remaining after five seconds or press again Hold mode Press A V while the sample is running to place the pump and timer in Hold Run time remaining and Hold na will display alternately Press A V while in Hold to OL continue the sample run Terminating a sample and resetting the pump Press while in Hold Sample Reset rSEt will flash r GEL on the LED To terminate sample and reset pump Press A V To continue sample run Press to return display to Hold Press A V 10 Continuous Run with Manual Stop Run time accumulates only while pump is running 5 Lire 999 minutes then automatically resets to zero and counts Continuous Run mode performs one sample from 1 to up to 999 again until the user manually stops the pump Digital display Continuous Run 1 Press A or Y to scroll to Cont Press A V to select it The pump will start and the LED will display cumulative run time up to 59 seconds in seconds then switch to minutes The timer will count up to 999 minutes autom
16. orten the number of presets to be scrolled through Preset 1 cannot be set to End Enabling Disabling Alarm and Fault Features 1 Press the security code XA V to enter setup mode 2 Press CAL The pump serial number will display briefly 3 Press A or Y to turn feature on or off see below Press to advance to next feature 4 Press A V to exit feature setup Press A V again to return to run time presets Feature ON OFF Button Beeper On Off LLAM I G L Digital display Digital display Button beep on Button beep off Alarm Beeper On Off OL O 1 PIO I Digital display Digital display Alarm beep on Alarm beep off Flow Fault On Off ZEL Peefri II ol PF EL Digital display Digital display Flow fault on Flow fault off Flow Fault Restart On Off r L rr ECLI Digital display Digital display Flow restart on Flow restart off Resetting Pump to Manufacturer Default y m E F E oe Press the security code KA V 3 and then press the CAL button The pump serial number will display briefly 2 Press repeatedly to scroll through until the LED 3 Press A V The word No will appear on the display To reset to factory default settings Press Yes Digital display will appear on the display Press A V Yes reset to pump default To retain existing settings Press to scroll to The number 30 will appear briefly then the display will return to run time presets Digital display No do not reset to
17. pump 17 default Digital display Pump default Maintenance 1 Keep the pump clean and free of dust and dirt It may be wiped with a dry cloth 2 Keep the battery charged see Battery Operation Charge periodically when pump is not used for prolonged periods Battery Operation Charging the battery To charge the battery insert the charger plug into the jack on the pump and the charger into a wall outlet A red LED will flash on the pump display to indicate the unit is charging When charging is complete the LED will stop flashing and the pump will go to sleep The QuickTake 30 can be operated using AC power See Operation To operate from AC Power The battery charges completely in five hours The pump will not sleep during charging Connecting a sleeping pump to the charger will wake it up from sleep The AC charger adapter can be used to extend battery run time but it is not a battery eliminator Therefore it will not provide indefinite run times Installing a Replacement Battery 1 Lift up and remove the two panels covering the screws from the back plate of the pump pressure fit 2 Loosen the four safety screws 3 Lift off back of pump case 10 Remove the two screws from the bracket slide bracket forward and lift it out Carefully lift the battery pack out of the case and detach it from the connector Attach the new battery to the connector Replace the battery pack in the p
18. r 15 min Manually set continuous run with manual shut off 1 to 999 min repeats 1 to 999 min runs indefinitely until user stops pump or power supply is depleted Intermittent sampling See Advanced Setup If the pump is unable to compensate due to excessive back pressure the pump will go into flow fault mode see page 13 for details Flow fault features are enabled as the default setting Flow fault may be disabled at the user s option See Advanced Setup Flow fault Flow fault displays immediately Pump shuts off after 5 seconds Fault restart Pump attempts restart every 10 seconds up to five times Viable cascade impactors spore trap cassettes e g VersaTrap asbestos cassettes wall cavity samplers and other impaction samplers that require flows from 10 to 30 L min ABS plastic 9 3 x 8 4 x 3 5 in 23 6 x 21 3 x 8 9 cm 4 8 lbs 2 2 kg Li lon Battery Shipment Rechargeable lithium ion batteries for use with SKC sampling pumps have been tested in accordance with the UN Manual of Tests and Criteria and are designated as UN3091 For air shipments Rechargeable lithium ion batteries in SKC pumps are subject to the A 45 exemption to the IATA regulations and are not regulated for air shipments This information must be written on the shipping document when shipping by air For ground shipments US DOT regulations specify a limit of 24 or fewer battery cells in one shipping box If you exceed 3 QuickTake 30 pump
19. r the programmed number of delay minutes while the LED displays a count down from cd om E i the set delay time to zero The pump will start sampling pa again The pump will beep four times and the display will Digital display flash Done after the desired cycles are completed Press Sample run completed to display cumulative run time Press to return to Done Press A V to return the display to the run time preset If a repeat sample is desired press A V 1 lt O Intermittent sampling settings are retained when pump goes to sleep User Options During Intermittent Sampling Viewing number of cycles remaining and cumulative run time Press repeatedly while the sample or delay is running If the unit is left untouched for five seconds the display g 5 will automatically return to cumulative time Terminating a sample and resetting the pump There is no Hold available in intermittent sampling Therefore pressing A V will stop the sampling and the 5Err LED will display SErr sampling error Press to view cumulative run time Press A V to return to run time presets 15 Programming Your Own Run Time Presets l Ze 3 5 Press KA V Pt 1 will alternately display with T xx This corresponds to the first stored preset time Press A to scroll to the number of minutes 1 to 999 Digital display Press Y to scroll to Cont Intt or End mode options End First preset
20. s with battery packs in one shipping box specific shipping requirements must be followed Contact SKC for more information or refer to the regulatory authority in your area See http www skcinc com instructions 1721 pdf for more information on maintaining disposing and shipping Li Ion batteries Indicates a warning caution or note www skcinc com Operation Button Sequence Buttons must be pressed in the sequence shown A or Y Press individually A VW Press both simultaneously A V Security code press in sequence Operating the Pump e To activate LED Press and hold for 2 seconds e To check battery status With the LED on press Battery Status Indicators Full charge approximately 75 to 100 battery capacity remaining Battery is charged enough to operate the pump approximately 25 to 75 battery capacity remaining H H E Battery charge is low charge battery approximately 1 to 25 battery capacity remaining HALL Low Battery Fault Pump will stop running beep and go to sleep in 10 seconds To operate from AC power The QuickTake 30 may be run using AC power with the battery and AC charger adapter Insert the charger plug into the jack on the pump and the charger into a standard wall outlet Operate the pump The charge light on the LED will flash if the battery is charging during AC operation The AC charger adapter can be used to extend battery run time but it is
21. splay will flash If no change to run time is desired press to move to delay time 2 When finished press Stor will flash on the display To save new setting Press A V Press to move to delay time setup To ignore new setting Press Display will move to Digital display the delay time Set run time If displayed values are not changed the flashing Stor will not appear and pressing will move the display to the next parameter to be set Setting Delay Time d 1 Press A or Y to increase or decrease delay time The display will flash If no change to delay time is desired press to move to number of cycles 2 When finished press Stor will flash on the display f Digital display To save new setting Press A V Press to move to Set delay time number of cycles setup To ignore new setting Press Display will move to the number of cycles Setting the Number of Cycles n 1 Press A or Y to increase or decrease number of cycles The display will flash If no change to number of cycles is desired press to return to Intt Digital display 2 When finished press Stor will flash on the display Set number of cycles To save new setting Press A V Press to return to Intt To ignore new setting Press The LED will return to Intt Start sampling by pressing A V The LED will count up to 59 seconds then switch to minutes up to the set minutes run time The pump will stop fo
22. t sample pump from weather when in use outdoors 4 9 Replace representative sampling medium used for calibration with a fresh unexposed sampling medium Press A or Y to scroll to a run time preset See Timed Run Continuous Run or Intermittent Sampling Once the desired preset is displayed press A W to start the pump running Record sample start time If the user wishes to stop sampling and reset the pump see Terminating a Sample ve and Resetting the Pump When sampling is completed a Timed Run mode The display will count down to f zero and the pump will stop The alarm will beep four I G mC times The display will flash Done Press to return to resets If a repeat sample is desired press A V b r ia Run mode The timer wil count up to nn 999 minutes automatically reset to zero and count I again to 999 minutes until user stops the pump Press H OL O A V to place the pump in Hold when the desired Da sampling time has elapsed Hold and cumulative run Pump and Timer in Hold time will flash alternately Press while in Hold Sample reset rSEt will appear on the LED Press A V to terminate the cumulative run and reset the pump If a repeat sample is desired press A V TR c Intermittent Sampling mode The display will eo ad count up to set run time count down from set delay reset pump time to 0 then run again Pump will cycle until the programmed number of cycles are completed The alarm
23. time Typical cumulative run timet Temperature Rechargeable 7 2 volt lithium ion Li lon battery see Li lon Battery Shipment on p 4 or battery with AC charger adapter 100 240 V Approximately 5 hrs Spore Trap e g VersaTrap 5 hrs at 15 L min battery only BioStage viable cascade impactor 4 hrs at 28 3 L min battery only 25 mm 0 8 um MCE filter 1 5 hrs at 10 L min battery only 25 mm 0 8 um MCE filter 2 5 hrs at 10 L min fully charged battery and AC adapter charger 25 mm 1 2 um MCE filter 9 hrs at 10 L min fully charged battery and AC adapter charger 37 mm 0 8 um MCE filter gt 14 hrs at 10 L min battery only Sampling times when using spore traps are usually lt 10 min SKC recommends reducing length of sample time when using a 30 L min flow rate to prevent overloading the media t Results obtained using a new pump and new fully charged batteries Pump performance may vary The AC charger adapter can be used to extend battery run time but it is not a battery eliminator Therefore it will not provide indefinite run times Operating 32 to 113 F 0 to 45 C Storage 4 to 113 F 20 to 45 C Charging 32 to 113 F 0 to 45 C O Protect sample pump from weather when in use outdoors Run time features Flow fault features Media compatibility Housing Dimensions Weight User selectable features user adjustable presets see Advanced Setup Preset timed runs 1 2 5 10 o
24. u exceed 3 QuickTake 30 pumps with battery packs in one shipping box specific shipping requirements must be followed Contact SKC for more information or refer to the regulatory authority in your area See http www skcinc com nstructions 1 72 1 pdf for more information on maintaining disposing and shipping Li Ion batteries Service Policy To return products to SKC for servicing 1 Call 800 752 8472 724 941 9701 for international customers to obtain a Return Materials Authorization RMA number and Product Decontamination Form 2 Carefully package the product Mark the RMA number on any correspon dence relating to the return and on the outside of the package Package product carefully to prevent damage during transit Include a contact name phone number shipping address RMA number and a brief description of the problem For nonwarranty repairs a purchase order number and billing address are also required The Service Department will contact nonwarranty customers with an estimate before proceeding with repairs Rechargeable lithium ion batteries for use with SKC sampling pumps have been tested in accordance with the UN Manual of Tests and Criteria and are designated as UN3091 To be exempt from Dangerous Goods Shipping requirements the box must contain 12 or fewer lithium batteries or 24 or fewer cells Therefore limit any box to be shipped to the following number of pumps Leland Legacy Pump 2 pumps QuickTake 15 1
25. ump case Replace the bracket and two screws Replace the back of the pump case and tighten four safety screws Replace the two panels and press until flush with case Battery Bracket Bracket screws Battery Battery connector Cautions and Warnings e To reduce risk of injury fire or electric shock always follow basic safety precautions when using this product e Batteries may explode or leak and cause burn injury if disassembled e Use only the approved charger and battery for this product Mixing this product with a different battery type or charger may cause damage to the pump and cause injury if the battery explodes Using non approved batteries or charger voids the warranty e Do not submerge the pump or subject it to any liquids Slide bracket forward and lift out Battery connector pulls apart O Protect sample pump from weather when in use outdoors Li lon Battery Shipment Rechargeable lithium ion batteries for use with SKC sampling pumps have been tested in accordance with the UN Manual of Tests and Criteria and are designated as UN3091 For air shipments Rechargeable lithium ion batteries in SKC pumps are subject to the A 45 exemption to the IATA regulations and are not regulated for air shipments This information must be written on the shipping document when shipping by air For ground shipments US DOT regulations specify a limit of 24 or fewer battery cells in one shipping box If yo
26. utck Take 30 Operating Instructions Catalog No 228 9530 SKC Inc 863 Valley View Road Eighty Four PA 15330 USA Form 40079 Rev 0709 Table of Contents BUICK SC assistant 1 A HOM aa sa et ta an ee ne ee 2 Performance Profile coccion 3 IDEE FAN e O caaeeroaneneneanaan 5 Mounting Sampling Media ccccooccncccccnncconnncnnncnnononcncnnonenonnnons 7 Calibration and Setting FlOW ooonccccoccnnoncnnoncnnnconannnncnnancnnnos 9 A E A 10 Sr ga o n E O AT TEETE E T ENA 12 Advanced SE LUD iaa 14 Maintenance score 18 Battery Operation resinas 18 Cautions and Warnings sense nen 19 VSS PONY ee ino 20 A q 21 Notice This operating instruction may not address all safety concerns ifany associated with this product and its use The user is responsible for determining and following the appropriate safety and health practices and regulatory limitations if any before using the product The information contained in this document should not be construed as legal advice opinion or as a final authority on legal or regulatory procedures QuickTake 30 Quick Guide Terms Star Button Turns on LED toggles between displays and exits without saving Up and Down Arrow Buttons AV scroll through presets increase or decrease sampling parameters and toggle between setup options Button Sequence A or Y Press individually A Y Press both simultaneously A V Security code press in
27. will beep four times The display will flash Done Press A Y to return to the run time preset If a repeat sample is desired press AV Digital display Digital display Cumulative run time 12 8 Remove and seal the sample medium 9 Re assemble the calibration train see Calibration and Setting Flow and verify flow 10 Send sample blanks and pertinent sampling information to a laboratory for analysis Terminating a Sample and Resetting the Pump For timed and continuous runs from a running pump press A V The pump is now in Hold Press while in Hold Sample reset rSEt will display Press A F to zero the cumulative run time and reset the pump For intermittent sampling there is no Hold Press A V to stop the pump The LED will display SErr sampling error Press to view cumulative run time Press A V to return to run time presets Cumulative run time resets to 0 even if intermittent sampling is started again Flow Fault Manufacturer default enabled User may disable feature If the pump is not able to compensate due to excessive back pressure a flashing FLOF will appear on the LED If the fault is not corrected within five seconds the pump will beep four times and stop running Restoring Sampling from a Flow Fault Fault restart manufacturer default enabled Digital display Terminate sample and reset pump LI I co__ Digital display Sampling Error
Download Pdf Manuals
Related Search